REPAIR/MAINT TO INTERNAL ROADS IN OTM AND MD ACCN INCLUDING CAT EYE, ROAD MARKING, PATHS, BERM, PAINTING AND OTHER ROAD FURNITURE OF AGE B/R-II UNDER GE (EAST) LUCKNOW

Amount

M&L for repair to pot holes of any depth n.exc 1 sqm each including sweeping free from dust and mud or water scroing sunken surfaces in roads, paths etc cutting around edges to at least 25 mm in depth making good by by applying tack coat with bituminous primer using paving bitumen VG 30 grade @ 5 kg per 10 sq m, putting in premix as specified for thin bituminous carpet (2.5 cm thick) well rammed, including rolling depth of potholes n exc 30 mm complete all as specified and directed.

Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area exc 400 Sqm & depth exc 50 mm and n exc 100 mm and removal from site to a distance n.exc 50m complete all as specified and directed.

M&L for Premix bituminous, macadam laid/rolled and compacted to required gradient and camber (consolidated thickness 75 mm or less) with @ 4% binder content (Bituminous grade VG-30) by weight of total mix, laid by mechanical paver, rolled and compacted with 8 to 12 tonne power roller complete all as directed and directed.

M&L for preparing black top surface by brushing with wire brushes for removing caked mud etc. using mechanical compressor to remove all loose dirt etc and applying evenly a priming/tack coat with bituminous primer using paving bitumen VG-30 @ 5.00 kg per 10 sq metre complete all as specified and directed.

M&L for 30 mm thick (consolidated thickness) Bituminous premix semi dense asphaltic concrete with 5.50% binder content (Bituminous grade VG-30) by weight of total mix, laid by mechanical paver rolled and compacted to required camber, gradient and for uniform smooth surface by using power roller 8 to 12 tonne capacity complete all as directed and directed.

Demolition of bricks (laid flat or on edge ) or brick tiles in floors, channels, kerbs, aprons ets (each layer) laid dry and pointed complete all as specified and directed.

M&L continuous brick edging with fly ash bricks with width equal to the width of the brick; laid dry on end vertically complete all as specified and directed

M&L for providing and laying 2.50 mm thick hot applied thermo plastic road marking materials in uniform thickness with glass beads as per clause No 803 of MORTH specification including cleaning of roads surface, heating the material within specified temperature limits for marking with all necessary arrangements required complete all as specified and directed.

S&F "Cat Eyes " of size width not more than 130 mm and height not more than 20 mm made out of strong engineering high impact resistant polymer with electronic welded lenses for retro reflective in dry and wet weather conditions along road complete all as specified and directed. Make : 3M/Stimsonite

S & F speed bumps made of heavy duty tough rubber of size 350 mm x 250 mm x 53 mm and weight 1.2 kg approx, colour black and yellow, as per manufacture instruction complete all as specified and directed Make: Dark Eye/Avery/Dennison.

Supply and fixing M.S pipe having 75mm outer dia, thickness 1.4mm and 1200mm length,duly powder coated in black/white colour and to be embedded in PCC 1:3:6 Type C2(using 40mm graded stone aggregate) with 3 nos x75mm high intensity prismatic(HIP) reflective tapes and MS pipe having powder coated jali & mesh for reflector portion & for anti theft.Below the reflective band of red/yellow/white colour high intensity micro prismatic type - IV tape (As per IRC 67/2010) of 75 mm each shall be provided complete all as specified and directed. Note: Necessary excavation for embedding of M S delinator shall be deemed to be included in the rate quoted against this item.

S & F Retro Reflective signage board made out of 600mmx900mmx 2 mm thick aluminuim sheet face to be fully covered with high intensity prismetic (HIP) Retro Refletive sheeting confirming to ASTMD-4956 01 as per colour required, letters and symbols shall be made of same Retro Reflective sheeting duly processed on base aluminum substrate board to be supplied alongwith back supported angle iron frame minimum 25x25x3mm all around and mounted on 75mmx75mmx6mm MS angle iron and this angle firmely embeded 0.60m below from ground level in PCC 1:3:6 type C2 (using 40mm graded stone aggregate) and duly painted with two coats of synthetic enamel paint over one coat of red oxide primer alongwith fixing accessories complete as per MORTH specification in repairs complete all as specified and directed.

Taking down existing finish completely including washing down and apply two coats of apex paint/ weather proof exterior grade emulsion paint over a coat of primer on plastered sufaces/concrete surface/Kerb stone including prepration of surfaces complete all as specified and directed.

Taking down existing finish completely including washing down and apply two coats of apex paint/ weather proof exterior grade emulsion paint over a coat of JK/Birla putty over primer on plastered sufaces/concrete surface/Kerb stone including prepration of surfaces complete all as specified and directed.

M/s Ram Singh Agarwal

Shakti Tar Products