Interior Works for Players Pavilion Zone 2 at IS Bindra Stadium Sector 63 Mohali

Amount

Lounge Room

Providing and laying Laminate wooden flooring (Grade AC5 or AC5+ laminates) 6 mm to 12 mm thick, having a good backing layer made up of plastic laminate or melamine, core made up of medium-density fiberboard (MDF),which is less resistant to impact damage and less resistant to being dented by heavy furniture, having a décor layer to give each floor its appearance and consisting of one or more sheets of paper impregnated with melamine resin and top wear layer having clear aluminum oxide finish that protects the decorative layer & imparts the desired level of sheen, from full gloss to low gloss, duly fixed to the base floor using adhesive as approved by the manufacturer. (Basic Rate 1750/Sqm)

Providing and fixing at all height false ceiling including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 750mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 750mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 375mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire/ Gypsum Screws of 19mm at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting.(Only Frame Work for POP and Wooden Ceilling), But excludes Gypsum or Ply/Board

Providing and fixing ply wood, plain lining, butt jointed including PVC Plug placed at 45 cm to 65 cm centers complete with necessary nails (Frame work shall be payable extra)

9mm thick commercial ply wood

12mm thick commercial ply wood (Lift Lobby FFl, Players Room FFL)

4mm thick 3 ply decorative ply wood with teak faced on one side

12mm thick commercial ply wood (Beam Panneling)

Coverng with 10mm Gypsum with 4mm Thick MDF pasted 1mm thick laminate (Beam Panneling)

Providing and Fixing 4mm Thick MDF pasted 1mm thick laminate on cold press and fixing to existing ply board with suitable adhesive (Beam Panneling)

Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ per liter respectively conforming to IS: 2547 (Part- 1 & II) 1976, applied on hacked / uneven background such as bare brick/block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish

Wall painting with plastic emulsion paint of approved brand and manufacturer to give an even shade (two or more coats)

Melamine polish two or more coats to give required finish including one coat of wood filler

Providing and Laying Wall paper on false ceiling/ walls (Basic Rate 1500/Sqm). Installed area to be measured.

Providing Picture frames with RHS/SHS MS section, with arrangement of light finished with powder coating/Duco paint/ and fixing with hilti/fischer fasteners. All complete as per drawing.

Providing, fabrication and installation of s make Manually operated Roller Blinds Translucent lighter shade fabric including all connected accessories, Complete as per specification document

Providing and Fixing with 18mm MR grade ply and finisfing. All complete as per drawing.Bar Serving Counter Cabinet Only Elevation Area to be Measured

Providing and Fixing with 18mm MR grade ply and finisfing. All complete as per drawing.Bar Counter Cabinet Only Elevation Area to be Measured

Player Dressing Area (National/ International)

Providing and fixing at all height false ceiling including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 750mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 750mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 375mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire/ Gypsum Screws of 19mm at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting.(Only Frame Work for POP and Wooden Ceilling), But excludes Gypsum or Ply/Board

Providing and fixing ply wood, plain lining, butt jointed including PVC Plug placed at 45 cm to 65 cm centers complete with necessary nails (Frame work shall be payable extra)

9mm thick commercial ply wood

12mm thick commercial ply wood (Lift Lobby FFl, Players Room FFL)

4mm thick 3 ply decorative ply wood with teak faced on one side

12mm thick commercial ply wood (Beam Panneling)

Coverng with 10mm Gypsum with 4mm Thick MDF pasted 1mm thick laminate (Beam Panneling)

Providing and Fixing 4mm Thick MDF pasted 1mm thick laminate on cold press and fixing to existing ply board with suitable adhesive (Beam Panneling)

Wooden profile on wall out of 50x25mm Kailwood Frame in wall panelling at 600mm c/c with neceaary rawla plugs/ screws fixed to wall for straight line and plumb lines of wall panelling

9mm thick commercial ply wood for wall panelling

4mm thick 3 ply decorative ply wood with teak faced on one side

Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ per liter respectively conforming to IS: 2547 (Part- 1 & II) 1976, applied on hacked / uneven background such as bare brick/block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish

Wall painting with plastic emulsion paint of approved brand and manufacturer to give an even shade (two or more coats)

Melamine polish two or more coats to give required finish including one coat of wood filler

Carpet tile size of 50cm × 50cm with .Made with 100% of Nylon with total thickness of 5 to 6mm approx. 15Years Warranty. . Wt of Carpet Min 590gm/Sqm

Providing and Laying Wall paper on false ceiling/ walls (Including layout/ cutting for lights, specialisd services.) Basic Rate 1500 per Sqm

Providing and fixing of teakwood moulding of 25x32mm to walls with necessary hardware. All Acomplete as per drawing

Outer Foyer

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre,

shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : (Including layout/ cutting for lights, specialised services.)

12.5 mm thick tapered edge gypsum moisture resistant board.

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish

Wall painting with plastic emulsion paint of approved brand and manufacturer to give an even shade (two or more coats)

Providing and Fixing 12mm Toughened Glass in railing and replacing of existing glass

Encasing of conduit with 2 runners of 18mm fixed to wall/rcc with suitable hilti/ fischer fastener, and covering with 12mm ply

Providing and fixing pelmet for receiving blinds 250mm clear and depth as per site/as shown in drawing with 18mm MR grade ISI ply. ixed to wall/rcc with suitable hilti/ fischer fastener. All complete as per drawing

Frame to be Replaced With Fixed Glass Partition 12mm thick toughened glass with dorma SS brush finish clips

Providing and Installation tensil Fibre including fraame fibre fasteners duco paint on metal, as per design and Specs. All complete as per drawing.Addition Of Tensile Fiber

Players Dressing Toilet ( National & International)

12.5 mm thick cement plaster 1:4

16mm thick cement plaster 1:4 in two coat work

Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge.

Providing and laying Polished Granite stone 18 mm thick flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/Highlighter/emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 600 x600 mm as approved by Engineer-in- Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement:4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Extra For Using 1000x800mm tile((Basic Rate of Tile Excluding GST 850/Sqm)

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm ( GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns(minimum), including factory painted after bending.) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all Tsections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size 24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-incharge.

Extra for using metal tiles as specified

Providing & fixing 16 gauge stainless steel pipe gate of grade 304 duly fixed at site with the help of M.S pivot & hinges grouted in cement concrete complete in all respect as per any kind of drawing & design (Players Toilet Ice Tub Ladder)

Steel work in built up tubular pipes (round, square or rectangular hollow tubes etc. ISI Marked) for flat shed (ie.Where no truss work is involved) including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. (Vanity Players Toilet)

Providing and Fixing 12mm thick toughened glass/ in partitions and parapets with cleats anchored to floor and Roof. All complete as per drawing

Supplying & laying of approved make and brand of scratch proof, flexible 10mm thick Sports Room rubber flooring, with suitable adhesive, as per the design & instruction of the Engineer-in-charge.(PlayerToilet)

Providing and Fixing 8mm thick toughened lacquered glass with cleats anchored to floor and Roof. All complete as per drawing. Job shall include necessary hardware to achor the glass with floor and roof , suitable hinges for openable door of Dorma make, also gaskets to seal the cubicle. All Complete as per drawing

Providing and Fixing Vanity with 19mm MR Grade MDF board, cladded with synthetic stone, 1mm laminate, with PU Finish and necessary dardware. All complete as per drawing. (MS work shall be paid Separately (Elevation Area to be Measured space between shelves not tobe deducted)

Public Toilets (Male/Female)

12.5 mm thick cement plaster 1:4

16mm thick cement plaster 1:4 in two coat work

Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge.

Providing and laying vitrified floor tiles in different sizes in light colour shades made using Full Body Technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 fine sand), complete. ( Full body vitrified tiles have pigment in entire body / thickness of tile which makes chips and scratches less noticeable and make na ideal choice for high traffic zones.) Size 600x600 mm

Extra over item no 3.07 for using size 2400x1200 using best suitable adhesive for the purpose, approved by Engineer In Charge Basic Rate 2100/Sqm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.

Providing and laying Polished Granite stone 18 mm thick flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/Highlighter/emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 600 x600 mm as approved by Engineer-in- Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement:4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Extra For Using 1000x800mm tile((Basic Rate of Tile Excluding GST 850/Sqm)

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm ( GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns(minimum), including factory painted after bending.) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all Tsections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

Extra for using metal tiles as specified

Providing and Fixing Washing Machine Unit with 19mm MR Grade MDF board, cladded with synthetic stone, 1mm laminate, with PU Finish and necessary dardware. All complete as per drawing. (MS work shall be paid Separately (Elevation Area to be Measured space between shelves not tobe deducted) 1800mm(L)x1000mm(H)x600mm(D)All Complete as per drawing.

Umpire Room

Providing and laying vitrified floor tiles in different sizes in light colour shades made using Full Body Technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 fine sand), complete. ( Full body vitrified tiles have pigment in entire body / thickness of tile which makes chips and scratches less noticeable and make na ideal choice for high traffic zones.) Size 600x600 mm

Extra over item no 3.07 for using size 2400x1200 using best suitable adhesive for the purpose, approved by Engineer In Charge Basic Rate 2100/Sqm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.

Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/Highlighter/emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 600 x600 mm as approved by Engineer-in- Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement:4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Extra For Using 1000x800mm tile((Basic Rate of Tile Excluding GST 850/Sqm)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre,

shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum moisture resistant board.

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish

Wall painting with plastic emulsion paint of approved brand and manufacturer to give an even shade (two or more coats)

Board Room

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge .15.7.4 In cement mortar

Dismantling tile work/ Kota/Granite in floors/ roofs/ cladding laid in cement mortar including stacking material within 50 metres lead. 15.23.2 For thickness of tiles above 25 mm and up to 40 mm

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

230mm First class burnt brick work laid in cement sand mortar 1:4 in superstructure

12.5 mm thick cement plaster 1:4

16mm thick cement plaster 1:4 in two coat work

Providing and laying vitrified floor tiles in different sizes in light colour shades made using Full Body Technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 fine sand), complete. ( Full body vitrified tiles have pigment in entire body / thickness of tile which makes chips and scratches less noticeable and make na ideal choice for high traffic zones.) Size 600x600 mm

Extra over item no 3.07 for using size 2400x1200 using best suitable adhesive for the purpose, approved by Engineer In Charge Basic Rate 2100/Sqm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.

Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/Highlighter/emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 600 x600 mm as approved by Engineer-in- Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement:4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Extra For Using 1000x800mm tile((Basic Rate of Tile Excluding GST 850/Sqm)

Providing and laying Laminate wooden flooring (Grade AC4 or AC4+ laminates) 6 mm to 12 mm thick, having a good backing layer made up of plastic laminate or melamine, core made up of medium-density fiberboard (MDF),which is less resistant to impact damage and less resistant to being dented by heavy furniture, having a décor layer to give each floor its appearance and consisting of one or more sheets of paper impregnated with melamine resin and top wear layer having clear aluminum oxide finish that protects the decorative layer & imparts the desired level of sheen, from full gloss to low gloss, duly fixed to the base floor using adhesive as approved by the manufacturer.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre,

shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum

Extra for Cove Making

Wooden profile on wall out of 50x25mm Kailwood Frame in wall panelling at 600mm c/c with neceaary rawla plugs/ screws fixed to wall for straight line and plumb lines of wall panelling

9mm thick commercial ply wood for wall panelling

4mm thick 3 ply decorative ply wood with teak faced on one side

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish

Wall painting with plastic emulsion paint of approved brand and manufacturer to give an even shade (two or more coats)

Melamine polish two or more coats to give required finish including one coat of wood filler

W I R I N G

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.

Group C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable and 1.5 sq.mm. FR PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel conduit including dismantling as required.

Group A

Group B

Supplying and drawing following pair 0.5 sq mm FR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required.

5/6 amps switch

2 way 5/6 amps switch

15/16 amp switch

3 pin 5/6 amp socket outlet

6 pin 15/16 amp socket outlet

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.

1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

8 Module (125mmX125mm)

12 Module (200mmX150mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.

1 or 2 Module

3 Module

4 Module

6 Module

8 Module

12 Module

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc., including supplying and fixing ball and socket arrangement, 2 Nos. down rods of 20 mm dia X 1.6 mm thick steel conduit up to 30 cm length, painting and wiring the down rods and connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

CABLE TRAYS PRE PAINTED WITH POWDER COATING with neccesary supports

MS perforated cable tray 150 X 50 X 1.6 mm

Electric Wire

25 sqmm 4 Core Copper Conductor

16 sqmm 4 Core Copper Conductor

10 sqmm 4 Core Copper Conductor

6 Sqmm 4 Core Copper Conductor

Light Fixture Supply

Supply of architectural Inground LED fixture ranging in 12W Fixture consruction shall be of aluminium die cast Hosuing having High Purity Lens and clear tempered glass with deep inset LEDs for achieveing desired beam angle and Glare free light having minimum system lumen efficacy of 900 lumens with IP>=66 with silicone gasket for use in Dry,Damp and wet locations. Fixture designed to directly install on the ground with help of mounting screws surface mounted type with ease of mounting. LED have useful life 50000 Hrs as per LM80.Fixture should withstand input voltage range form 100V-240V and operating temperature range form -20degC to 40degC . Make: Philips, Wipro, Trilux.

Supply of 24V 100W IP >=65 rated LED Driver for Driving LEDs with input having inbuilt surge protection of 3KV minimum and Minimum conversion efficiency of 85%. Driver must be IS 15885 & BIS approved with R number and CE mark.

Supply of IP67 rated S Connectors Suitable for 2C for Connecting multiple Fixtures to enable looping of multiple fixtures to increase system efficiency.

Supply of IP67 rated T Connectors Suitable for 2C for Connecting multiple RGB Fixtures to enable looping of multiple fixtures with single DMX to increase system efficiency. Approved Make of Pharos, Wipro, Meanwell.

Supply of 35 W +/- 1W Round Hollow ring suspended fixture having Housing made up of extruded Aluminum powder coated White/Black Housing with 100lm/W ,THD<10%,PF>=0.95 CRI 80 and CCT of 4000K only with High efficiency, non-yellowing PMMA diffuser having dia of 600 mm with Surge prortection of2.5 KV. Make: Philips, Wipro, Trilux.

Supply of IP20 12W +/-1W COB LED Reccess Mounted Downlighter with titable head having minimum system lumen efficacy of 100 lm/W with Pressure Die cast aluminium hosuing and clear glass cover having P.F.>0.95 with THD<10% ,CCT 4000K ,CRI 80.The LED life of 50000 Hrs at L70.The Input voltage range shall be 150V to 270V with surge protection 2KV. Make: Philips, Wipro, Trilux.

Supply of IP20 15W +/-1W Low Glare COB LED Reccess Mounted Downlighter having minimum system lumen efficacy of 90 lm/W with minimum system lumen output of 1350 lumens with Pressure Die cast aluminium hosuing with White Finish Trim and High transmittivity diffuser with Chrome Finish reflector having P.F.>0.95 with THD<10% ,CCT 4000K ,CRI 80.The LED life of 50000 Hrs at L70.The Input voltage range shall be 100V to 265V with surge protection 2.5KV. Make: Philips, Wipro, Trilux.

Supply of 20 W + /- 1W Decorative Pendant Mounted LED Fixture made of fiber reinforced Plastic with Diifused Glass Dome with 600 mm dia having minimum system lumens of 1300 with minimum life of 50000 burning hours, CCT 4000K, CRI 80, with surge protection of 2 KV. Make: Philips, Wipro, Trilux.

Supply of IP20 LED Strip Light in 5mtr spool in 10W/ Mtr having 700 lm/mtr with polymide double sided PCB housing having surge protection of 3 KV including driver. Make: Philips, Wipro, Trilux.

Supply of IP20 15W +/-1W COB LED Track Light with system lumen efficacy of 100 lm/W with White housing with Pressure Die cast aluminium hosuing and clear glass cover having P.F.>0.95 with THD<10% ,CCT 3000K/4000K ,CRI 80.The LED life of 50000 Hrs at L70.The Input voltage range shall be 150V to 270V. Make: Philips, Wipro, Trilux.

Supply of suspension mounted cylindrical led downlighter 20W +/- 1W Fixture having inset clear glass diffuser with extruded aluminium black housing having system lumen efficacy of 80 lm/W with P.F.>0.95 and THD<10% with beam angle 36 degree .The LEDs with minimum life of 50000 Hrs. The LEDs used in the luminaire shall have CCT of ANSI Bin 4000 K and CRI of minimum 80. Make: Philips, Wipro, Trilux.

Supply of led fixture 15 W +/- 1 W LED Recess Mounted Downlighter with Deep inset diffuser for glare free lighting. Round Shape Fixture having Die Cast Heat housing and minimum system lumen efficacy of 120 lm/W with system lumen output of 1800 lumens with P.F.>0.95 and THD<10% ,CRI 80.The LED with Useful life of 50000 Hrs at L70 ,CCT of 5700 K with CRI of minimum 80.The Input voltage range shall be 150V to 270V .Fixture have Surge Protection 2kV. Make Phlips, Wipro, Trilux.

Supply, installation, testing and commissioning of complete loud speaker ceiling mounted type , Complete as required (Similar to Bosch LBD 0606) with metal grill with necessary wiring and conduting complete connectivity with existing speakers.

Supply of LED Module IP65 Rating of 1.0 W / Module in 6000K for Signage Lighting. Make Osram/ Philips

Supply of LED Driver for LED Modules for Signage Lighting Make Osram/Philips

Providing LED Eye Ball Lights 6Watt IP 65 rating for display unis Make Philips, OSRAM

Pyle PDICBT852RD 250 Watt Wireless Bluetooth Speaker (Multicolor) (Basic Price 18000/-)

Misc for Electrical Works

Provinding and Fixing hook and chain for installation of Chandelier

Installation Testing and Commissioning of Speakers/ Light Fixture including hardware required for installation of fixture. All complete as per drawing

Downlighter/ Ball Light/Speakers

LED Light with fixture, luminaire and Drivers

LED Strip Light for Signages

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 .

Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cord less remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature.

2.0 TR Four Way Cassette AC

Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The unit shall have automatic force shut down provision in case of fire on receiveing signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature.

Mid Static Ductable units (minimum 45 pascal external static pressure)

High Static Ductable units (minimum 110 pascal external static pressure)

Supply, installation, testing and commissioning of following minimum capacity Tower VRV/VRF Tower Type Indoor Floor mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, grill, necessary supports, vibration isolation, cord less remote control etc.,supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature.

04 TR Tower AC

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required :

6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

Control Cabling

PVC insulated PVC sheathed twin flexible copper conductor cable Supply and erection of PVC insulated PVC Sheathed twin flexible wire with copper conductor complete in all respect as desire by the Engineer in Charge.

PVC insulated PVC sheathed twin flexible copper conductor of size 1.5 Sq. mm (48/0.20mm)

Providing and fixing PPRC/ UPVC 10kg/Cm2 pipes of various sizes with 6 mm Nitrile insulation for condensed water drainage from Indoor unit to nearest disposal point in toilet/ outside rain water harvesting system as approved by architect/consultant to the entire satisfaction of EIC.

Supply, installation, balancing and commissioning of Site fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes,hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.

Thickness 0.63 mm sheet 24 Guage

Thickness 0.80 mm sheet 22 Gauge

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32kg/m³,with 25mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications.

Supplying and fixing of following thickness duly laminated19 mm aluminum foil of mat finish closed cell Nitrile rubber (Class “O”) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

Removing Existing AC Supply Linear Grills and Control Dampers

Removing and Reinstallation of AC Units

Core Cutting upto 150mm Dia and 230mm Deep

Dismentalling Pipes and Fittings

Dismentalling pipes laid in trenches to correct gradient and alignment and jointing of UPVC pipes cutting and jointing, including f specials (Specials and Solvent should be of same make as that of pipes) complete in all respects.

110mm o/d pipe

160mm o/d pipe

Dismantling Sanitary fixtures such as Eurpoean/Indian/Orissa W.C., PVC / China ware cistern, Wash Hand Basin, Urinal Pot, Sinks and CP Fittings and disposal of dismantled material within a distance of 100 Mtr. complete in all respect as required by Engineer-in-Charge.

Eurpoean/Indian/Orissa W.C.,

PVC / China Ware Cistern

Wash Hand Basin / Urinal Pot

CP Bib Cock/Angle Cock/Stop/Concealed Stop Cock

Wall mixer / Sink Mixer / Basin Mixer /

Bathroom Assessories such as Soap Dish, Towel Rail, Towel Ring, Towel Bracket, Mirror, Toilet Paper Holder, Seat Cover, Jet Pressure and all other accessories.

Dismantling heavy flat iron clamps including cartage / disposal within 5 Km.

100mm i/d Clamps

75mm i/d Clamps

50mm i/d Clamps

Providing and fixing Stainless Steel pipe and fitting of grade AISI 304 as per JIS standard 3448 complete with press type fitting i/c fixing of the pipe with clamps at 1.00 m spacing including cutting and making good the walls including testing of joints complete as per direction of Engineer-in-charge. Work shall include necessary fittings threaded, plane. or any special fitting required for the job for particular dia of pipe (The pipe length inserted in the fitting shall not be measured for payment) Internal work - Embedded in wall

15.88 mm outer dia Pipe

22.22 mm outer dia Pipe

28.58 mm outer dia Pipe

34.00 mm outer dia Pipe

Providing and fixing Stainless Steel pipe and fitting of grade AISI 304 as per JIS standard 3448 complete with press type fitting i/c fixing of the pipe with clamps at 1.00 m spacing including cutting and making good the walls including testing of joints complete as per direction of Engineer-in-charge. Work shall include necessary fittings threaded, plane. or any special fitting required for the job for particular dia of pipe (The pipe length inserted in the fitting shall not be measured for payment) Internal work - Exposed on Wall

For 15.88 mm outer dia pipe

For 22.22 mm outer dia pipe

For 28.58 mm outer dia pipe

For 34.00 mm outer dia pipe

Drainage

Single Socket Type A

110mm o/d single socket SWR UPVC pipe lines laid complete

90mm o/d single socket SWR UPVC pipe lines laid complete

75mm o/d single socket SWR UPVC pipe lines laid complete

Single Socket Type B

160mm o/d SWR UPVC pipe lines laid complete

110mm o/d SWR UPVC pipe lines laid complete

90mm o/d SWR UPVC pipe lines laid complete

75mm o/d SWR UPVC pipe lines laid complete

For 110mm o/d pipes

Single Tee

Elbow 90 Degree (All side socketed)

Coupler

P Trap/Floor Trap 110mm x 110mm

Single Y-Junction

Double Y-Junction

Cutting chase in brick walls in cement or in floor for embedding G.I. or C.I pipes line and making good the same to its original condition.

Size 75 mm x 50 mm

Fixtures

Providing and fixing in position Chinaware extended wall mounted E. W.C. type suite (size 66 x 46 x 77.5 cm ) with P trap or S trap of approved make (to the approval of the Engineer-in-charge) with or without 10 ltr. chinaware matching flushing cistern and seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge.

Chinaware wall mounted E.W.C without cistern including seat cover complete in all respect.

Providing and fixing in position concealed cistern including flushing plate of approved make (to the approval of the Engineer-in- charge) complete in all respect.

Providing and fixing in position vitreous Chinaware white Senso urinal size 37 x 39 x 61 cm of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass Urinal waste Coupling dome type 32mm outer length 75 mm complete in all respect.

Toughned Glass Partition 8mm thickness size 450 x 900 mm C/S

Providing and fixing in position C.P. brass Tumbler Holder of approved make (to the approval of Engineer-in-charge ) fixed into wall with rawl plugs and C.P brass screws complete in all respect.

Providing and fixing C.P. brass Urinal Spreader Ocular-Regular complete with fittings for urinals complete

Providing and fixing Stainless steel health faucet complete in all respect.

Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32mm dia with one C.P. brass pillar tap including Rack Bolt Screw Pair 115mm long complete in all respect.

Size 630mm x 500mm (above counter oval)

Providing and fixing in position C.P. Brass Auto close Pillar Cock of approved make (to the approval of Engineer-in-charge) Deduct for CSR item 30.33

Providing and fixing in position C.P. brass bottle trap 32mm dia with 40 mm seal of approved make (to the approval of Engineer-in- charge) complete in all respect.

Providing and fixing in position C.P. brass overhead shower 1 flow with shower arm with 15mm i/d inlet of approved make (to the approval of Engineer-in-charge) complete in all respect.

Providing and fixing in position paper holders of approved make (to the approval of Engineer- in-charge ) fixed in to wall with C.P brass screws complete in all respect.

C.P. brass toilet paper holder

Providing and fixing in position towel rails / ring of approved make (to the approval of Engineer-in-charge ) fixed in with rawl plugs embedded in walls with brass screws complete in all respect.

C.P. brass towel Rails size 15mm dia 610mm long

Providing & Fixing in position C.P./Aluminium Khunti of approved make (to the approval of Engineer-in-charge ) fixed into wall with C.P. brass screws and rawl plugs etc. complete in all respect.

C.P. Brass khunti with 3 pegs

Providing & Fixing in position C.P. Brass flange Dome of approved make (to the approval of Engineer-in-charge ) under various fixtures complete in all respect.

Providing & Fixing in position C.P. Brass extension piece 25mm long to 100mm long of approved make (to the approval of Engineer-in- charge )with various fixtures complete in all respect.

C.P. Brass extension piece, 25mm long to 50mm long

C.P. Brass extension piece 75mm long

C.P. Brass extension piece 100 mm long

Providing & Fixing in position C.P. Brass Hexa Nipple 15mm of approved make (to the approval of Engineer-in-charge ) complete in all respect.

Providing & Fixing in postion stop cock / Angle valve of approved make (to the approval of Engineer-in-charge ) complete in all respect.

C.P.brass 15mm stop cock Male and female end

Providing & Fixing in postion liquid soap container of approved make (to the approval of Engineer-in-charge ) complete in all respect.

C.P. brass liquid soap container

Providing and fixing in position premium range C.P. Brass Fittings and accessories of approved make (to the approval of Engineer-in- charge ) complete in all respect.

C.P. brass 15mm Concealed stop cock with adjustable wall flange with seal.(Outer +Inner Body)

Providing and fixing divertors of approved make (to the approval of Engineer-in-charge ) for bath and shower system complete in all respect.

Single lever concealed divertor for bath and shower system (3 inlet flow) with body and upper part

Providing & fixing in position C.P. copper tube connection of approved make (to the approval of Engineer-in-charge ) complete in all respect.

C.P. copper tube connection of size 15 mm x 450 mm with C.P. Brass nut

Providing and fixing in position SS Grating with frame of approved make (to the approval of engineer in charge) complete in all respects.

Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining.

Providing and fixing in postion storage type automatic electric water heater pressure / non pressure type thermostatically controlled, single phase, vertical wall mounted of approved make (to the approval of Engineer-in-charge) with thermostats, inner container of stainless steel complete with 1 Mtr. three core flexible cord with plug, non return valve and pressure release valve complete including fixing and testing complete in all respect

Stainless Steel Shower Panel Tower System, 4 ways bathing, Rainfall Shower, Handheld Shower, Wall Mount Easy Connect Shower Panel Kit, Chrome Finish

Providing and Fixing of hanging system for all dia pipe with tie rod, fastener and hanging clamp

75mm to 160mm

Providing Installation Testing and Commisiioning of hand dryer Material As Approved Power 1650W, Voltage AC220-240V , 50/60Hz, Operation Touch Free Infra-Red Activation, Auto Cut Off 30 Sec, Speed 25000 RPM Noise Level 80db(A), Heater Element Heating PTC Element Air Speed 85-95 m/s, Drying Time 15 s, Motor Brush Motor Blowing Volume 150 m3/h, Waterproof IPX1, Weight 12 Kg category hand dryer machine

Providing and Fixing AUTO CUT HRT ROLL DISPENCER in SS 304 Body.

Core Cutting upto 150mm Dia and 230mm Deep

Fire System: Removing and Refixing testing and commisioning fire smoke/heat detectors, job includes making identification of detectors of existing location on drawing and submitting to client for approval, removing and storage of detectors in safe place, the cable shall be managed before false ceiling is completed and installation, testing and commission of detector with necessary hardware, support, after false ceiling is complete. All complete as per revised fitout drawing.

Paras Art Studio

THE 21ST CENTURY BUILDERS AND ENGINEERS

LOCO DESIGN PVT LTD