PROVN OF EXTERNAL SERVICES SUCH AS FOOTPATH, SEWAGE LINE, DRAIN AND CONNECTED ITEMS FOR 12 QTR FOR MES KEY AT NAMKUM

Amount

Excavation in trenches n.exc 1.5 metres wide and n.exc 1.5 metres deep for foundation etc for shafts, cesspits, manholes etc n.exc 10 Sqm on plan and n. exc 1.5 metres in depth and getting out in hard/dense soil.

Returning filling in incl spreading leveling watering, well ramming in layers not etc 25 cm hard/dense soil

Removing excavated materials etc not exc 50 metres depositing where directed at a level of n.exc. 1.5 metres above the starting point

M&L pre cast RCC (1:1.5:3) type A-1 as in manhole cover, drain cover and set in cement mortar (1:4) including necessary formwork complete all as specified and directed.

M&L brick work with sub class 'B' brick straight or curved on plan exc 6 metres radius with old size bricks built in cement mortar (1:4) complete all as specified and directed.

M&L PCC 1:3:6 and type C-2 using 40mm graded stone agregate for concrete bed to drain pipes including packing under hunching against the sides of pipes after they laid and tested for 150mm dia pipes

M&L cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate in fondation and mass concrete for manhole surface channels and drains

M&L Salt-glazed stone ware drain (SWSG) pipe grade 'A' 150 mm dia laid in trenches & jointed in CM 1:1 and tested complete all as specified and directed.

M&L PCC (1:2:4) type B1 using 20mm graded stone aggregate in coping etc, including weathering slightly rounded champers angle forming channels & form work

M&L PCC (1:2:4) type B-1 using 20mm graded stone aggregate as benching including forming channels using forms, moulds etc complete all as specified and directed.

M&L for TMT bars 10mm dia and over cut to length bent to shape required including cranking binding spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips deformed or twisted bars complete all as specified and directed..

M&L steel TMT Bars 6 to 8mm dia cut to length bent to shape required and binding with MS wire complete all as specified and directed.

M&L rendering 15mm thick cement mortar (1:4) on fair faces of brick or concrete surfaces and finished even and fair without using extra cement.

S&F 110mm dia, PVC (SWR) Pipes single socketed in any length with rubber rings joints land in trenches or floor and making good the surface, complete all as specified and directed.

S&F in repairs 110mm dia, PVC (SWR) Pipes single socketed in any length with rubber rings joints fixed to walls, complete all as specified and directed.

S&F 75mm dia, PVC (SWR) Pipes single socketed in any length with rubber rings joints fixed to walls, complete all as specified and directed.

S&F PVC (SWR) vent cowl, 110 mm dia

S&F PVC (SWR) bend, 110 mm dia

S&F PVC (SWR) junction single, (Single T) equal or unequal 110mm dia

S&F PVC (SWR) bend, 75 mm dia

S&F PVC (SWR) junction single, (Single T) equal or unequal 75mm dia

Material & labour for 100mm dia cast iron Nahani traps with grating including jointing with waste pipe fixed in cement concrete type B-1 (1:2:4).

M&L PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement.

Material & labour for 75mm bore PVC floor traps plain with grating including jointing with solvent cement complete all as specified & directed.

Extra for forming fair finished drain or channels not exc. 30cm inner girth finished even and smooth with using extra cement complete all as specified and directed.

Add or deduct for each 25mm girth or part there of over or under 30cm ditto

S&F tubes medium grade galvanised with all fittings & fixed complete to walls & ceiling or laid in floors 15mm bore etc complete all as specified and directed

All as per item No. 27 above but 20mm bore

Supply & fixing rotational moulded polyethylene water storage tanks 1000 liters capacity, (cylindrical, vertical in closed top) hoisted and fixed in position with all fittings all as specified including 20 mm PVC ball valve including dismantling existing water tanks complete all as specified & directed.

S&F Gun-metal, globe or gate valves 20mm, with iron wheel head, screwed both ends for iron pipe etc comlete all as specified and directed .

S&F Gun-metal, globe or gate valves 15mm, with iron wheel head, screwed both ends for iron pipe etc comlete all as specified and directed .

M&L for cement concrete 1:3:6 type C-1, using 20mm graded stone aggregate.) as in surface channel and drain complete all as specified and directed..

Surface exavation n.exc 30cm deep and averaging 15cm deep and getting out in sooft/lose soil all as specified and directed

Material & labour for hardcore of broken stone or boulders of gauge n.exc. 63mm, deposited,spread and leveled in layers n.exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L 75 mm thich PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed

M&L Sand filling under floors including watering and consolidation

M&L Machine pressed precast concrete coloured Inter locking paver block of any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment over sand cushion & laid over sub base all as specified and directed.

Excavation in trenches n-exc 1.5 m wide and exc1.5 m and n-exc 3.0 deep in soft/ disintegrated rock and getting out as specified and directed

M&L for RCC type B-1, 1:2:4 (using 20mm graded stone aggregate) as in beam, cantilever or lintle exc 1.5m span.

M&L RCC type B-1, 1:2:4 (using 20mm graded stone aggregate) as in slab supported on wall beam, column in floors, roofs, landing and balconies etc

Form work to sides and soffits of floor and roof beams lintle, cantilver, shelves etc incl support, overhangs etc also splays between floor and beams fair finished flat surfaces of concrete flat rough finished surfaces

Form work to soffits of suspended slab such as roof slab, floor slab, landing etc and similar work nexc 20cm thick flat rough finished surfaces of concrete surfaces.

Loose filling with aggregate of broken stone or boulders of guage 80 to 150mm in soakage pit, soakage well etc

M & L 75 mm thick PCC 1:3:6 type C-2 using 20mm graded stone aggregate including finished surface even & fair without using extra cement as in plinth protection including necessary form work of edge all as specified and directed. Note: 10mm wide and 75mm deep joints shall be made at 3 mtr intervel and at each corner and the same shall be filled with using bitumen 85/25 and sand in the ratio 1:3.

M & L newly plastered surface of walls and applying two coats of apex paint by machanical applicator over a coat of cement primer complete as specified and directed.

M & L complete removal of existing surface of walls of any description by washing, rubbing down and applying two coats of apex paint by machanical applicator over a coat of cement primer complete as specified and directed.

M & L repairing broken edges of chajja's, roof projection, Fascias etc . In small widths/depths ( exposed area not exc 0.16 Sqm ) by breaking the cracked/loose portion and filling with Cement Mortar / Plain Cement Concrete 1:2:4 ,Type B-0 , using 12.5 mm Crushed stone aggregates , over GI wire mesh, giving a coat of anti corrosive paint to exposed Reinforcement and using coat of anti corrosive paint to exposed Reinforcement and using chemical for bonding old and new concrete/plaster and finishing with CM 1:3 plastering, incl 2 coats of white wash to match the exisitng surfaces incl removing debris , necessary scaffolding , etc all as specified and directed. (Note : Reinforcement if any provided shall be measured and paid separately)

All as per ser item No 47 above herein before but exposed area exc 0.16 Sqm but not exc 0.5 Sqm

Supply & fix mild steel framed work such as grills, grating, Flat iron, etc with end of bars shouldered and/ or riveted forged into spikes, framed guard bars, railings and similar work complete conforming to Fe-410-0 or Fe-310-0.

Taking down cement plaster on wall of any description incl racking out joints hacking for key and scrubbing down with water complete.

M&L rendering 15mm thick (10mm + 5mm)in CM 1:4 in two coats on fair faces of brick work , finished even and fair without using extra cement with WPC.

Supply only water proofing compound (liquid),ISI marked.

Providing pressure gunniting averaging 25mm thick in cement mortar 1:3 for soffits of slabs. Chajjas etc complete all as specified and directed including providing double scaffolding as required and removal of the same on completion of the work complete all as required and directed and applying Epoxy Treatment [Nito Bond AR of M/s. Fosroc or its equivalent in M/s. Dr. Fixit] prior to guniting to facilitate proper bonding with old surfaces complete all as specified and as directed.

Providing pressure gunniting averaging 30 mm thick in cement mortar 1:3 for columns / beams/ fins/parapets complete all as specified and directed including providing double scaffolding as required and removal of the same on completion of the work complete all as required and directed and applying Epoxy Treatment [Nito Bond AR of M/s. Fosroc or its equivalent in M/s. Dr. Fixit] prior to guniting to facilitate proper bonding with old surfaces complete all as specified and as directed.

M&L Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc.including (powder coating 50 Micron) complete all as specified.

M&L Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc .including (powder coating not less than 50 micron) complete all as specified.. complete all as specified.

Material & labour for brick work with sub class ‘B’ bricks, straight or curved on plan, exc. 6 metre mean radius built in CM(1:4) as in half brick wall complete all as specified and directed.

Material & labour for brick work with sub class ‘B' bricks in one brick thick honey comb walling, built in CM(1:4) complete all as specified and directed.

Material & labour for preparation of new or previously untreated steel surface of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description, not otherwise described, over 10cm width or girth and change of existing colour including removal of scaled paint where ever required and applying two coats of synthetic enamel paint complete all as specified and as directed

M&L for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth and change of existing colour including removal of sclaed paint and applying two coats of synthetic enamel paint over a coat of red oxide primer for change of existing colour complete all as specified and as directed.

M/S Manoj Kumar Sinha

M K Enterprises

BUILDCON ENTERPRISES