Electrification of Power house, Tower, Installation of generator, Solar Street lights, ESE lightning arrester at Tadri lighthouse. Provision of service cable and Replacement of Street light fittings in Staff Quarters compound at Tadri under DLL Goa

Amount

Electrification of TADRI LIGHTHOUSE - ANNEXURE – I (LIGHTHOUSE TOWER)

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

3 x 1.5sq. mm (for fan and light points in service room and tower bottom)

3 x 2.5sq. mm (From DB to Switch Board)

4 x 1.5sq. mm (for staircase wiring From LH tower bottom to service room)

3 x 4sq. mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6A switch

2way 5/6A switch

15/16A switch

3pin 5/6A socket outlet

6pin 15/16A socket outlet

Supplying and fixing following size/ modules, PVC surface mounted box along with modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75mm x 75mm) (for Wall mounted fan and Angular Holder light at lantern room )

3 Module (100mm x 75mm)

12 Module (200mm x 150mm)

Supplying and fixing 3pin, 5A Ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Installation, testing and commissioning of ceiling fan/wall mounting fan including wiring the down rods of standard length (up to 30cm) with 1.5sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling / wall, including connections with 1.5sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Supplying and fixing PVC batten/angle holder including connections etc. as required. (1No. for lantern room)

Switch Gear and DB

Supplying and fixing 5A to 32A rating, 240/415V, 10kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole 6A (1No. for service room) (2Nos. for LH bottom) (2Nos. for Staircase)

Supplying and fixing following rating, double pole, (single phase and neutral), 240V, residual current circuit breaker (RCCB), having a sensitivity current 30mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. (at service room and LH bottom)

40A (1No. for Service room)

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required.

8way, Double door (1No. LH tower Service room) (1No. for LH bottom)

Earthing with G.I. earth pipe 4.5m long, 40mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supply of Indoor Industrial Tube Light Battens, with 4' 20/22W LED tube (refer S. No. 1.06 for installation)

Supply of 10W LED Bulk Head Luminaries IP65/66/67 with integrated LED source

Supply of LED Bulb 12W B22

Supply of Wall Mounting Fan, 400mm sweep, Hi-Speed Model along with Bracket for Wall mounting

Supply of 32 x 12.5mm DLP mini trucking system each 2.1m length each (for staircase light wiring including vertical and horizontal fixing of trunking double run)

Supply and laying of 3Core x 6sq. mm Copper armoured PVC insulated/PVC sheathed/XLPE LT Power UG cable double run as required (Laying from Power house to tower one in service and another one is as spare for Main Light)

Supply and laying of 3Core x 2.5sq. mm Copper armoured PVC insulated/PVC sheathed/XLPE LT Power/Control UG cable double run as required (Laying from Power house to tower for Stair case Lightning)

Making Cable trench for laying cable direct in ground including excavation, sand cushioning, protective covering and refilling the trench, etc., as required (For LT Power cable from EB pole to Power house)

Supply of Bare Copper wire, 8SWG

Laying of 8SWG copper wire in cable duct from earth pit to service room DB & LH tower bottom DB

Laying & fixing of cable duct (for vertical run) and re-routing for new cable in cable duct from Tower bottom to lighthouse tower top (service room) (9m height tower)

Making earth pit charges (additional) of S. No. 1.11 for Lighthouse located at hill & rocky area difficult to digging earth pit (heavy duty machinery and labour charges)

Miscellaneous items for the purchase of SS screws and washer (for fixing cable duct), drill bits, nylon fixtures (heavy wall plugs), 250mm cable ties, SS 'U' Clamps, flexible pipes, etc.,

Electrification of TADRI LIGHTHOUSE - ANNEXURE – II (POWER HOUSE, LT PANEL, DG SET & SOLAR STREET LIGHT)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75mm x 75mm)

3 Module (100mm x 75mm)

6 Module (125mm x 125mm)

8 Module (125mm x 125mm)

12 Module (200mm x 150mm)

Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required

5/6A switch

15/16A switch

3 pin 5/6A socket outlet

6 pin 15/16A socket outlet

Supplying and fixing PVC batten/ angle holder including connections etc., as required (fancy type)

Supplying and fixing 3pin, 5A Ceiling rose on the existing junction box/ wooden block including connections etc., as required

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc., as required

Installation, testing and commissioning of Ceiling fan, including wiring the down rods of standard length (up to 30cm) with 1.5sq.mm FRLS PVC insulated, copper conductor, single core cable etc., as required

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5sq.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc., as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/PVC conduit as required

2 x 1.5sq. mm (for Lamp Holder)

3 x 1.5sq. mm

3 x 2.5sq. mm

3 x 4.0sq. mm

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted\ including earthing etc., as required. (But without MCB/RCCB/Isolator)

12way, Double door

Supplying and fixing 5A to 32A rating, 240/415V, 10kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc., as required.

Single pole 10A

Single pole 16A

Supplying and fixing following rating, double pole, 240V, Isolator in the commissioning etc., as required existing MCB DB complete with connections, testing and Commissioning etc., as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240V, residual current circuit breaker (RCCB), having a sensitivity current 30mA in the existing MCB DB complete with connections, testing and commissioning etc., as required.

Earthing with copper earth plate 600mm X 600mm X 3mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7m long etc., with charcoal / coke and salt as required for Power house, panel board earthing, DG body earthing and neutral earthing

Providing and fixing 25mm X 3mm copper strip on surface or in recess for connections etc., as required.

Earthing with G.I. earth pipe 4.5m long, 40mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc., with charcoal/ coke and salt as required.

Supply of Indoor Industrial Tube Light Battens, with 4' 22W LED tube. (refer S. No. 2.07 for installation)

Supply of LED Bulb 12W B22

Supply of Ceiling Fan, Electrophoretic lacquered/ Electroplated surface for anti-rusting, Double Ball Bearing, High speed fan with wider tip blade for effective air circulation with Sweep 1200mm and High performance even at low voltage (refer S. No. 2.06 for installation)

Supply of Outdoor Street light Luminaire, Die cast Aluminium body, powder coated, with structured LED arrays 25W LED, IP65/66 protection

Providing and fixing of Street light Bend pipe 1" dia GI class "C" pipe including clamp/SS screws etc., of length 1m bend at 60° in the top 1’ and bottom 2’ length for fixing 3Nos. of Heavy Duty Clamps

Supply of Bare Copper wire, 8SWG earth wire connecting between earth tape to body of panel board, power house earthing etc.,

Labour charge for laying 8SWG wire from ground level to Distribution box through PVC pipe with clamp

Supply and Fixing of Three phase Energy meter board with necessary holes, comprising of Kit Kat 3Nos. 63A re-wireable porcelain fuse carrier and with neutral link, 63A Isolator as a complete set (as per Drawing)

Supply and Fixing of Kit Kat 63A re-wireable fuse and neutral link kit (Aerial fuse carrier to be installed on top of the EB pole)

Supply and laying of 4Core X 10sq.mm Copper armoured PVC insulated/PVC sheathed/XLPE LT Power UG cable as required (From EB Pole to Power house)

Supply of 10sq.mm Copper Flexible Cable (for internal loop wiring in for connecting Meter board to DB, Generator etc.,

Making cable trench for laying cable direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc., as required. (For power cable from EB pole to Power house)

Applying wall white putty and painting in wherever plastering work done in all quarters

Miscellaneous items for the purchase of screws, Bolts, Nuts & Washers, drill bits, cable ties, 25mm PVC bends, tees, 1/2/3/4 way junction boxes, Cutting plates, 12 mm Fan hooks, Fan rod for extension, wire strippers, steel spring, PVC junctions boxes, SS Clamp etc., Wall white putty and paints

Making earth pit charges (additional) for the Lighthouse located at hill & rocky area difficult to digging earth pit (heavy duty machinery and labour charges) (for plate earthing)

Making earth pit charges (additional) for the Lighthouse located at hill & rocky area difficult to digging earth pit (heavy duty machinery and labour charges)

Red stone cutting charges for concealed wiring and making hole in 600mm wall for cable entry as buildings are constructed by Red stone/laterite stone.

Design, fabrication, Supply, Installation, testing and commissioning of wall mounting type LT Distribution panel, Fabricated out of 16SWG CRCA Sheet not less than 2mm thick, powder coated, dust/vermin proof with hinged doors (as per the drawings 9.1.4, 9.1.4A & 9.1.4B) (Sample on drawing 9.1.5)

Supply and Installation testing and commissioning of 5kVA Single phase, Portable type, Diesel start and Diesel run Generator of 4 stroke single cylinder, air cooled, self-start arrangement (battery included)

Supply and Installation of 25W All-in-one LED solar street light comprising of 6m height pole, Battery included in the luminaire enclosure, with water proof (IP65) and corrosion resistant, along with Lithium Ferro Phosphate battery (LiFePo4) Operating from dusk to dawn, with motion sensor (as per drawing 9.1.6 as per layout drawing 9.1.7)

Supply of 5kVA, Single Phase, air cooled, servo controlled voltage stabilizer of copper transformer, compact size, operating voltage of 160-260V, Output at 230V +/- 1%, Voltage correction 15V/sec, with provision to monitor input and output voltage

Supply of 0-48V, 40A, Dimmerstat controlled battery charger comprising of Voltmeter, Ammeter, Protection fuses for input and output, compact size, Air cooled type

Foundation and base work for Solar Street lights: Foundation Base of Streetlights: Earthwork Excavation in beach area and take out water during excavation (0.6 x 0.6 x 0.5m), 1:2:4 (stone aggregate 20mm) for Concrete Work of the foundation with Post pipe placed in concrete, Brick Work (0.45 x 0.45 x 0.45m) for post base, Plastering Work (4 x 0.45 x 0.45) +(0.45 x 0.45) for post base and Painting Work applying 1 coat White cement primer Paint and 2 coats Synthetic enamel Red Paint, labour charges inclusive of materials (as per drawings)

Transportation charges for carrying by hand such as, Generator, distribution panel Street light poles, copper plates, cement, bricks, UG cables, etc., through rough pathway from approach road to Lighthouse

Electrification of TADRI LIGHTHOUSE - ANNEXURE – III (ESE LIGHTNING ARRESTER)

Providing and fixing 25mm x 3mm copper strip on surface or in recess for connections etc., as required. (For Lightning arrester Down Conductor)

Earthing with Copper Earth plate 600mm x 600mm x 3mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7m long etc., with charcoal / coke and salt as required (For Lightning arrester earthing as per IS 2309 1969)

Supply and Installation of Early Streamer Emission (ESE) Lightning Air Conductor. Equipped with Stainless central pick up rod. Full electrical continuity between the tip and the earth point. Fully autonomous (no battery, no external power supply required) Collect energy through streamer emission controlled with detects the lightning and trigger a streamer (3.5kV and 20A). The ESE shall cover the area of 60m Radius. Manufactured as per CPRI Requirements & as per Indian standards.

Supply and Installation of single length 6m heavy duty elevation pole (Lightning arrester mast) made of GI “C” Class minimum 60mm dia., with a M20 thread at the top to fix the ESE unit. Necessary provisions shall be provided for stay wire termination, fixing of insulated copper flat laying from the top (ESE unit) of the mast to bottom of the mast. The bottom of the mast shall be welded to 300mm x 300mm x 10mm GI plate and supported gazette plate with 4Nos. of 22mm hole suitable for making foundation bolt for fixing the mast. The stay wires shall be made of 6mm SS in the grade of 304 with suitable SS wire rope clamp which withstand salty atmosphere and wind speed of 150km/hr. (as per Drawing 9.1.8)

Supply and Installation of Additional 6 feet Triangle GI support to the mast with hand rail using 40mm GI ‘C’ class pipe (as per Drawing 9.1.8A)

Supply and Installation of IP67 Digital Lightning counter for recording the lightning flashes

Supply of 50mm Insulator pipe for fixing ESE lightning arrester pipe with basement of mast pipe

Supply of Test link box (GI)(Test link point should be copper strip with brass bolt and nut) (as per drawing 9.1.10)

Installation of ESE Lightning arrester, insulator pipe, lightning mast Pipe, flash counter, Test link, etc.,

Making Earth pit charges (additional labour charges) refer S. No. 3.02 (for earthing) Lighthouse located at hill & rocky area difficult to digging earth pit (heavy duty machinery and labour charges) (for plate earthing)

Additional labour risk charges for Laying of 25mm x 3mm copper strip (refer S. No 3.01) (For vertical run) at the outside of LH tower on surface of wall from Lighthouse tower top (lightning arrester) to LH bottom earth pit by clamping the tape at the distance of 2 feet using insulator, fixtures (Nylon wall plug), SS Screws and Tools (including all accessories like, Nylon rope, pulleys, safety belt etc.,)

Miscellaneous items for the purchase of S.S screws, SS washer, bolt & nut, Strip Insulator - 80Nos., Insulation tapes, Insulation sleeves, Fixtures (Nylon wall plugs), etc.,

Electrification of TADRI LIGHTHOUSE IQ & STAFF QUARTERS COMPOUND - ANNEXURE – IV (SERVICE CABLE & STREET LIGHTS)

MODULAR SWITCH BOXES, SWITCHES AND SOCKETS

Supplying and fixing following size/ modules, PVC box along with modular base & cover plate for modular switches in recess etc. as required (for Water Heater)

3 Module (100mm x 75mm)

Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required (for Water Heater)

15/16A switch

6pin 15/16A socket outlet

CONDUIT AND CABLE

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

3Core x 1.5sq.mm (For Street light)

3 x 4.0sq.mm

SWITCH GEAR

Supplying and fixing 5A to 32A rating, 240/415V, 10kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole 16A

Double pole 6A

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (But without MCB/RCCB/Isolator)

6 way, Double door

Supplying and fixing following rating, double pole, 240V, Isolator in the commissioning etc. for existing MCB DB complete with connections, testing and commissioning etc., as required

Supplying and fixing following rating, double pole, (single phase and neutral), 240V, residual current circuit breaker (RCCB), having a sensitivity current 30mA in the existing MCB DB complete with connections, testing and commissioning etc., as required

Supplying and fixing 20A, 240V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top along with 20A, “C” Curve, SP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc., as required

Earthing with Copper Earth plate 600mm X 600mm X 3mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7m long etc., with charcoal / coke and salt as required (For three phase Panel board earthing)

Earthing with G.I. earth pipe 4.5m long, 40mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal / coke and salt as required (For IQ, NA-II Qtrs. and LHA Qtrs.) (as per drawing 9.1.11)

GI PIPES FOR ROAD CROSSING

Providing, laying and fixing 80mm dia G.I. pipe (medium class) in ground complete including trenching (75cm deep) and re-filling etc., as required (for CC road crossing)

Supply of Outdoor Street light Luminaire, Die cast Aluminium body, powder coated, with structured LED arrays 25/30W LED, IP65/66 protection

Supply of Outdoor IP65 Post Top Gate Light Luminaries, 15/20W LED with 12”/18” dome type

Supply of 32 x 12.5mm DLP mini trucking system each 2m length each (for staircase light wiring including vertical and horizontal fixing of trunking double run)

Supply of Bare Copper wire, 8SWG earth wire connecting between earth tape to body of panel board, IQ Earthing, NA-II Qtrs. and LHA Qtrs. earthing

Supply and Fixing of Three Phase Energy Meter board with 3Nos. Kit Kat 63A re-wireable porcelain fuse carrier with neutral link with Sheet Steel enclosure, one set of 4way TPN bus bar box for Incomer Mains, another 3Nos. Kit Kat 63A re-wireable porcelain fuse carrier with neutral link for DB (to IQ, Pump House and Streetlight), and 2Nos. 32A fuse re-wireable fuse carrier and neutral link for Qtrs. as a complete set (as per Drawing 9.1.13)

Supply and Fixing of 3Nos. Kit Kat 63A re-wireable Porcelain fuse and neutral link kit (Aerial fuse carrier installed on top of the EB pole)

Supply and Fixing of Single phase Energy FRP SMC meter box suitable for existing energy meter with Kit Kat 32A fuse and neutral link for NA-II Qtrs. and LHA Qtrs.

Supply and laying of 2Core x 6sq.mm Copper armoured PVC insulated/PVC sheathed/XLPE LT power UG cable as required (Laying from junction box to NA-II quarters, junction box to LHA Quarters and Junction box to IQ [NA-II- 40m, LHA-50m, & IQ-75m])

Supply and laying of 4Core x 16sq.mm Copper armoured PVC insulated/PVC sheathed/XLPE LT power UG cable as required (From EB Pole which is located on road to compound premises area via climbing RCC staircase through overhead poles)

Supply of 16sq.mm, Single Core Copper Flexible Cable (for internal loop wiring for meter board to DB)

Supply and laying of 3Core x 4sq.mm Copper armoured PVC insulated/PVC sheathed/XLPE LT power UG cable as required (From DB to well pump motor which is located near to sea)

Supply and laying of 3Core x 4sq.mm Copper PVC insulated flat cable as required. (well top to submersible motor)

Labour charge for laying 8SWG wire from Distribution box to earth pit through PVC pipe with clamp

Making cable trench for laying 2Core x 6sq.mm LT service / power cable direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc., as required (From Distribution box to NA-II, LHA & IQ)

Fabrication, Supply and Installation of 3" Dia Class "C" Class GI pipe 6m Length with clamp arrangement (as per drawing 9.1.14) for carrying the EB power supply through 4Core x 16sq.mm UG cable on overhead along with applying 1 coat primer and 2 coats aluminium paint [for O/H service line UG Cable]

Foundation and base work for Pole for carrying Earthwork Excavation in beach area and take out water during excavation (0.6 x 0.6 x 0.5m) for the foundation of pole 1:2:4 Concrete Work (0.6 x 0.6 x 0.5m) for the foundation with Post pipe placed in concrete inclusive of materials [for O/H service line UG Cable]

Making earth pit charges (additional) for the Lighthouse located at hill & rocky area difficult to digging earth pit(heavy duty machinery and labour charges) (for plate earthing)

Making earth pit charges (additional) for the Lighthouse located at hill & rocky area difficult to digging earth pit(heavy duty machinery and labour charges) (for solid pipe earthing of Qtrs.)

Supply installation of 25W All-in-one LED Solar Street light comprising of 6m height pole, Lithium Ferro Phosphate battery (LiFePo4) Battery included in the luminaire enclosure, with water proof (IP65) and corrosion resistant

Foundation and base work for Solar Street lights: Base of Streetlights: Earthwork Excavation in beach area and take out water during excavation (0.6 x 0.6 x 0.5m) for the foundation of streetlight, 1:2:4 Concrete Work (0.6 x 0.6 x 0.5m) for the foundation with Post pipe placed in concrete, Brick Work (0.45 x 0.45 x 0.45m) for post base and placing of pipes for cable entry, Plastering Work (4 x 0.45 x 0.45) +(0.45 x 0.45) for post base and Painting Work applying 1 coat White primer Paint and 2 coats Synthetic enamel Red Paint. (4 x 0.45 x 0.45)+(0.45x 0.45), inclusive of materials (as per drawing 9.1.7)

Design, fabrication, Supply, Installation, testing and commissioning of wall mounting type LT Distribution panel, Fabricated out of 16SWG CRCA Sheet not less than 2mm thick, powder coated, dust/vermin proof with hinged doors (as per the Drawing 9.1.4, 9.1.4A & 9.1.4B)

Making cable trench for laying 3Core x 4sq.mm LT power UG cable direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc., as required (For water pump located nearer to sea)

Labour Charges for Erection of GI Pole for Laying 4Core x 16sq.mm UG Cable on overhead from EB pole (bottom through RCC staircase to inside the compound) including laying, securing and termination

Electrician Charges for replacement of 12 Nos. of Street light fittings, switch boxes etc.

IMPULSE SOLUTIONS

Abacus Infrastructures Pvt Ltd

CIS GLOBAL INFRATECH PVT LTD

TELECON SYSTEMS