REPAIR TO LEAKAGE/SEEPAGE, PLASTERING, JOINERY AND SUNKEN PORTION IN BR II AREA UNDER GE AF GORAKHPUR

Amount

Demolition of reinforced cement concrete in roofs, beams, staircase, lintels, chajja, RCC OHT etc complete all as speciifeid and directed at site.

M&L reinforced cement concrete (nominal mix) type B1 1:2:4 (20 mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, copies, deck slabs, shelves and for fixing rungs etc including necessary form work upto 2 story building complete and directed by Engineer-in-Charge.

S&F for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete, all specified and directed.

Ditto but mild steel TMT bars 6 to 8 mm dia complete all as speciifeid and directed at site.

Supply only liquid water Proofing Compound, complete all as specified and directed by Engineer-in-Charge.

Dismantling of brick tiles or terracing tiles single layer bedded in cement mortar on roof complete all as specified and directed.

Demolition of cement concrete in roof including plastering and leeping including cleaning surface of roof with wire brush / mechanical brush throughly to remove old dirt / loose particles to expose clean concrete slab clean with watering etc complete all as specified and directed.

M&L for cutting out cracks to V section in existing roof or terracing, cleaning out, wetting, grouting with cement and sand slurry in 1:3 complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.50mm graded stone agg with WPC as in padding to maintain proper slope as required al as specified (WPC shall be paid separatly.) complete all as speciifeid and directed at site.

M&L for priming over roof surface @ 0.25 Ltr/Sqm over a cleaned roof surface and applying one coat of bitumen painting with hot blown grade bitumen 85/25 @ 1.20 Kg/ sqm and minimum 3mm thick reinforced with polyester non wove fabric ( wt not less than 150gms/ sqm) land on primed surface by forced application complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in roof kerb / benching in radius 10 cm with waterproofing compound as per manufacturer's instructions complete all as specified and directed.

M&L 40mm thick brick tiles laid on cement mortar 1:6 and pointing in CM 1:3 15mm thick screed bed complete all as specified and directed.

ditto but except tile complete all as specified and directed.

Demolition of brick work built in CM of any descritpion complete all as speciifeid and directed at site.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius in cement mortar 1:4 as in manholes/drain

All as per item No. 16 above but except bricks.complete all as speciifeid and directed at site.

Taking down cement plaster on brick wall and ceiling including raking out joints hacking for key scrubbing down with water etc complete all as directed.

M&L for rendering 15 mm thick in CM ( 1:6 ) plaster on wall / concrete surfaces finish fair and even without using extra cement.

M&L for rendering 15 mm thick in CM ( 1:4 ) plaster on wall / concrete surfaces finish even and smooth without using extra cement complete all as specified.

M&L for rendering 05 mm thick in 1:3 cement mortars as in ceiling, complete all as speciifeid and directed at site.

M&L including preparation of new plastered surfaces and applying two coat of white wash on ceiling, complete all as speciifeid and directed at site.

M&L including preparation of new plastered surfaces and applying two coat of cement base paint on wall, complete all as speciifeid and directed at site.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed. Note : - Sanding of surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer.

M&L for preparation of old surfaces applying two coats of oil bound distemper over 1mm thick putty using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface to achieve excellent application using limited manpower complete all as specified and directed. Note : - Sanding of surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer.

Dismantling of false ceiling board ,fiber insulation board any thickness including wooden cover fillets aluminium frame work complete all as speciifeid and directed at site.

S&F anodised aluminium snap grid ( size 605mm x 605mm) frame work for false ceiling with hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long and fixing 4mm thick non asbestos fibre cement building building boards on aluminium framework complete all as specified and directed.

M&L for raking out cement mortar joints/pointing to brick work in walls or to bricks on edge in floors, surface channels, roofs etc complete all as specified and directed

M&L for flush pointing in brickwork laid flat on roof surface etc with using cement mortar 1:3 complete all as specified and directed

Dismantling existing transparent PVC sheets in roof complete all as specified

S&F 2.0mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed in roof etc complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering complete all as specified and directed.

M& L 0.50 mm thick (total coated thick) pre-painted galvalume aluminum zinc coating GI based corrugeted steel sheet having tensile sterength of 550 Mpa as an roof covering /cladding to wall fixed with self tapping screws as specified complete all as specified and directed.

Dismantling of structural steel work including doors gates , framed truss etc as in grills of windows.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L For Expanded metal, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members weight not exceeding 4 kg per sqm, complete all as speciifeid and directed at site.

S&F in repairs HDPE PVC lid (cover) for 500 to 1000 Litres capacity PVC tanks, complete all as specified and directed by Engineer-in-Charge.

Dismantling of water tanks of any type/pattern exc 500 ltr not exc 1000 Ltr and removing from site of work, complete all as specified and directed.

M&L for rotational moulded polythylene water storage tanks 1000 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified in SSR-I including brass valve high pressure with polythne float and fly nut , tank nipple as required complete, screwd for iron pipe or brass ferrule size 25 mm bore, complete all as speciifeid and directed at site.

S&F 15 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified.Make :- Prayag/ Polytuff

S&F 25 mm size Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Disconnecting existing tanks of capacity 500 litre, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting at other place as directed and reconnecting , repair if required and re-fixing in position complete all as specified.

Taking down eaves gutter rain water pipe (any size of pattern) including all fittings, heads, shoes, bends, swan-necks and cleaning or fixing or removal, complete all as specified and directed.

Supply and Fixing 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including suitable clamps at one meter of interval complete all as specified.

S&F in repairs for PVC (SWR) bends/Tees of radius, suitable for 110mm dia PVC pipes fixed complete all as speciifeid and directed at site.

Taking down chowkats with shutters exceeding 1.5 Sqm but n. exc 4 sqm each ( without taking off shutters from the frames), complete all as speciifeid and directed at site.

Taking down chowkat or frames of frame of any description or specification (wooden/iron/aluminium) (w/o taking off shutters from the frames) not exc. 1.5 sqm each with shutters (without taking off shutters from frames)

Second class hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete.

M&L PCC 1:3:6 type C-1 as in filling in holes of hold fasts complete all as speciifeid and directed at site.

S & F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed by the Engineer-in-Charge

S&F 2nd class hard wood 35 mm thick factory made plain framed, panelled shuttes (two panels) with lock rail and panel of 9 mm BWP commercial or 12 mm veneered particle board with commercial veneer on both faces the size of rail and stile as per IS 1003 (Part-I) kiln seasoned and cehmically presured treated, complete all as speciifeid and directed at site.

M&L for preparation of new wooden surfaces and applying two coat synthetic enamel paint over a coat of pink primer complete all as speciifeid and directed at site.

M&L for 100mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinged pin, anodised and fixed, complete all as speciifeid and directed at site.

S&F aluminium anodised barrel tower bolt extruded section 150 mm long, complete all as speciifeid and directed at site.

S&F 125 mm size extruded aluminium alloy handles, fabricated type anodised, complete all as speciifeid and directed at site.

S&F 300 mm long ordinary rat tail rod pattern springs including roller and roller platecomplete all as speciifeid and directed at site.

S&F 250 mm long aluminiunm sliding door bolt with hasp and staple bolt type and fixing clips of sheet cast or extruded section fixing bolts and sliding bolts of extruded section complete.

S&F PVC door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening, all as specified and directed.

S&F 100 mm size stainless steel but hinges, complete all as speciifeid and directed at site.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & botttom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame including 2 nos aluminium bow handle 150mm and 2nos aluminium tower bolt of size 150mm etc complete all as specified and directed.

Repair/easing/ readjusting of aluminium door/window shutters by taking down shutters from frame and dismentling members of shutters like, glass, rails and styles by necessary cutting, grinding of members etc and refixing of same including rubber gasket ,hinges , handle, screws etc complete all as specified and directed.

M&L anodised sliding type window with frame size 60X40X2.00 mm thick and shutter with section bearing bottom 52x18X1.50, top 39.4 x17.7 x1.5mm and sides 39.4 x 17.7 x 1.5mm (suitable for moving over two track over top of frame work, top and side section of size 61.6x31.75x1.5mm and bearing bottom track of size 61.6x31.75x1.5mm incl necessary aluminium jointing cleats,glazing cleats,rubber packing anodised aluminium snape beading, screws etc with 5mm thick tinted/plain glass in panels incl all fitting & fixture complete all as spesified and directed.

M&L anodised aluminium grill Wt nexc 3.50 kg per sqm with all fittings& fixture, shape and size as approved complete all as spesified and directed .

M&L anodised aluminium doors with frame size 101.6X44.45X 2 mm thick and shutter aluminium anodised and top rail 47.62 x 44.45 x 1.5 and style 47.50X 44.50 X 1.50 mm,lock rail 83.5X 44.45 X 1.50 mm and bottom rail150.00X 44.50 X 2.50 mm incl necessary aluminium jointing cleats,glazing cleats,rubber packing anodised aluminium shape beading, screws etc with panelling in two parts with 4 mm thick aluminum composite board in lower panel and 5mm thick tinted/plain glass in panels incl all fittings, MS 4 lever mortice lock, floor door spring and all fittings& fixture complete all as spesified and directed

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless stell cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed.

S&F in repair door closer hydraulically regulated, aluminium (extruded section body )designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60kg complete all as speciifeid and directed at site.

S&F in repair 5.5mm thick, sheet/ tinted glass, ordinary quality to be fixed with aluminium beading and rubber gas kit in aluminium frame work as in door/ window/ partition etc all as specified and directed.

M&L for 4mm thick both side aluminium decorative sheet laminated partition panel for fixing in aluminium door shutters by taking out old ply/board from exsting aluminium door shutters complete all as specified and directed

S& F in repair aluminum glazing clips / beading for aluminum door and window, complete all as speciifeid and directed at site.

S& F in repair rubber gasket for packing / beading for aluminum door and window, complete all as speciifeid and directed at site.

Demolition of lime concrete from sunken portion or concrete of any description and any position and waste materials out from MoD Land complete all as specified and directed .

M & L for preparation of RCC surface of sunken sab ( Floor & sides ) by brushing with grinder machine and cleaning thoroughly with water and removing old treated surface complete. 1. Application of two coats of poly urethane based chemical treatment (as per manufacture instruction Dr. FIXIT /FOSROC/COCO/STP. 2. M & L 15 MM thick CM (1:4) plaster overchemical coating. Note-1.Countinuity with cementtitious WPT beyond sunken portion in toilet shall be maintained 2.In case of Rectangular/ circular RCC tank ,all internal faces including ceiling.

M&L cement concrete 1:5:10 with 40 mm graded stone coarse aggregate in sunken floor 150 mm thick all as specified and directed at site.

M&L 100mm thick cement concrete type B-1 1:2:4 (20mm graded aggregate finished even and smooth with using extra cement in sunken portion) mixed 3% of water proofing compound with cement (water proofing compound shall be measured and paid separately under respective items of this schedule).

Demolition of PCC floor ,plinth and paving not exceeding 15 cm thickness below or above ground level , complete all as speciifeid and directed at site.

M&L 75mm thick PCC (1:3:6) type C1 as in plinth protection etc finished even and smooth without using extra cement, complete all as speciifeid and directed at site.

M&L for providing cement concrete type B-1, 1:2:4 using 20 mm graded aggregate as in 40 mm thick flooring ,finishing the concrete surfaces even and smooth using extra cement, complete all as speciifeid and directed at site.

Taking up or down steel tubing and connections, 15 mm bore including cleaning for refixing or removal or store, complete all as speciifeid and directed at site.

Fixing only GI tubing medium 15 mm bore with all fittings to wall/ceiling or laid in floors completed all as specified and directed

S&F 15mm bore steel water tubes "medium grade" galvanized with all fittings such as bends, elbows tee etc and fixed to walls and ceiling in floor complete all as directed.

Taking up or down steel tubing and connections, 20 mm bore including cleaning for refixing or removal or store, complete all as speciifeid and directed at site.

Fixing only GI tubing medium 20 mm bore with all fittings to wall/ceiling or laid in floors completed all as specified and directed at site.

S&F 20mm bore steel water tubes "medium grade" galvanized with all fittings such as bends, elbows tee etc and fixed to walls and ceiling in floor complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises, complete all as speciifeid and directed at site.

M&L Non-skid ceramic coloured tiles 7 to 8 mm thick ( square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured of tiles including laying of screed bed or bedding layer of mortar 15mm thick in cm 1:6 complete all as speciifeid and directed at site.

M&L for non skid Ceramic coloured tiles 7-8 mm thick (square or recatngular ) area of each tiles exceeding 0.11 sqm and not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement over 15 mm thick screed bed in 1:4 CM complete all as directed.

M&L for glazed ceramic coloured tiles in vertical surface 350 x250 x7mm / 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match coloured tiles including rendering 10 mm thick on faces of brick or concrete surfaces in cm 1:3 complete all as specified and directed.

M&L for Light shade Vitrified ceramic tiles 10mm thick (square/ rectangular) polished, area of each tile not exc 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in colored cement to match over 15mm thick screed bed in 1:4 cement mortar complete all as specified and directed.

S&F in repairs Vitreous China wash basin, white, flat back, size 550 x400 mm excluding water taps waste chain plugs and porcelian stopper but including brackets (Make: Parryware/Cera)

S&F in repairs 15 mm bore pillar tap fancy type cast copper alloy chromium plated screwed down high pressure with or without lettered ' Hot' or 'Cold' with long screw shanks screwed for iron pipe or union complete all as speciifeid and directed at site.

M&L in repairs 32 mm dia waste coupling of PTMT (Half or full threaded) ( Minimum weight 32 mm 45gms/40mm-60gms), complete all as speciifeid and directed at site.

S&F in repairs PVC connection 15mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repairs PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repairs bottle trap of PTMT having minimum water seal of 25mm (min weight 32mm-260gms/ 40mm 270gms)

S&F repairs Vitreous china wash down water closet pan (pedestal pattern) with any type of 'P' or 'S' trap excluding flushing cistern and flush pipe, including fixing of water closet complete with plastic water closet seat black/white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device. complete all as specified and as directed.

S&F in repairs Vitreous China water closet squatting pan, 'Orrisa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete including connection to trap, and to flushing pipe, anti syphonage pipe etc. including trap set in and including concrete and making good to floor. complete all as specified and directed.

M&L in repairs PVC 10 Ltrs valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets

S&F in repairs cast copper alloy chromium plated caste copper alloy screwed high pressure with crutch or butter fly fancy type angle cock, of 15 mm bore complete all as specified and directed.

M/S SHAILZA TRADERS

M/s Durgesh Kumar Mishra

M/S NITISH ASSOCIATES

M/S B.P. CONSTRUCTION

Sheo Prasad

M/s Pandey Trading Company

M/ s J S Kapoor And Sons