Construction of Waiting Lounge and Meeting Room at Residential Quarter No.-2 (Occupied by Honble Chief Minister Jharkhand) at Booty Road Dindayal Nagar, Ranchi

Amount

Dismantling tile work in floor and roof laid in cement mortar including stacking material withing 50M lead. For thickness of tiles 10mm to 425mm.

Providing designation 75 A brick work in C.M. (1: 3) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacture, over the plastersd wall surface to prepare the surface even and smooth complete.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

Providing two coats of plastic emulsion paint of approved shade and make over old surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily Size 600X600

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily Size 600X1200

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPV profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately)

Casement door single panel withzink alloy (zamak) 3D hinges, multi-point locking system with cylinder, zinc alloy (zamak) powder coated handles on both sides.

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 5.5 mm thick glass panes

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including:

Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1 .6 mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110m bend

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm Shoe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 Sq.Mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular type switch, modular plate,suitable GI box etc. as required.

Wiring for circuit / submain wiring alongwith earth wire with the following sizes of PVC insulated, copper conductor single core cable in surface/ recessed PVC conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire.

2 x 6 sq.mm. + 1 x 6 sq.mm. Earth wire.

Supplying and fixing of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps. modular switch, connection, painting etc. as required.

Supplying and fixing of following modular switch/ socket outlet on the existing Modular plate & switch including connection but excluding modular plate etc. as required.

3 pin 5/6 amp socket outlet

15/16 amp switch

6 pin 15/16 amp socket outlet

Supplying and fixing following size/ modules, GI box Boxes alongwith modular base & cover plate for modular switches in recess etc as required.

6 Module (78mmX205mmX50mm)

8 /9Module (78mmX230mmX60mm)

12 Module (135mmX205mmX60mm)

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supply and fixing of stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supply and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

Supplying and fixing following way, three pole and neutral, sheet MCB distribution board 415 volts,on surface /recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, Phosphatized and powder painted including earthing etc. as required (But without MCB / RCCB / Isolators).

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required

Supplying and fixing following 240 volts `C' series, miniature circuit breaker (MCB)suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Copper Tube of size 1/4" for aplit ac unit 1/1.5/2/3 Tr capacity including nitride rubber

Copper Tube of size 5/8" for aplit ac unit 1/1.5/2/3 Tr capacity including nitride rubber

drain pipe. For AC

5 KVA wall mounted automatic voltage stablizer from range 140V to 280V

Outdoor stand for 2.0 Tr Split AC

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I.

Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Supplying chemical emulsion in sealed containers including delivery as Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.:

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead do--do-- all as building specification and direction of E/I

Providing and laying in position cement concrete of (P.C.C) with nominal mix of 1:2:4 in Foundation and Plinth do---do-- all Complete job.

Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL)

Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and fixing machine cut, mirror/ eggshell polished , Marble slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire Red or Dark Emperadore etc. stone work for wall lining (veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily Size 1200X1200

Providing & Applying high quality acrylic modified resin based texture of Dholpur/Red sand stone Pattern with anti algae and UV resistance properties to be applied as intermediate finish in desired pattern @ 43.04 kgs/10 sqm to form film of 1- 1.5 mm thickness after scrapping and properly cleaning the surface to remove loose particles from the plaster surface, followed by top coating with Premium Acrylic Smooth exterior paint with Silicone additives of required shade by two or more coats @ 1.43 litres/10 sqm, complete as the direction of Engineer -in-Charge.

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)

Carriage

A) LOCAL SAND , LEAD - 3KM(P)

B) SAND , LEAD - 8KM(P)

C) STONE CHIPS , LEAD - 22KM(P)

D) BRICKS , LEAD-1k+7p=8KM.

E) STONE METAL , LEAD - 20KM(P)

E) STONE CHIPS , LEAD - 22KM(P)

Non-Shedule Items Providing and fixing in position black out curtain with aluminium extrusion track system over the window opening. Required length of cross over shall be provided to ensure total black out. Curtain wands shall be at required distance from the floor. The cost shall include all related hardware, materials, necessary scaffolding etc. Complete. [Manually Operated]

Supplying and Fixing & Fitting of Footmat All complete as per building specification and direction E/I

Providing and fixing Supreme Thermal Insulation Shield in Ceiling, over 2"x1" aluminium pipe under layer Rockwool insulation including labour charge. All complete as per building specification and direction E/I.

Providing & laying 1.5mm THK SBS modified self-adhesive, cross laminated HDPE Valero lining waterproofing membrane, Dr. Fixit Samshield XL 1500, conforming to IS 16471:2017 Type A, requirements of waterproofing structures, over the solvent based bituminous Torchshield primer @ 4 sq.mt/litre. Including surface cleaned thoroughly of all contaminants like dust, oil and grease. All complete as per building specification and direction E/I

Providing and fixing all height wall paneling of 12 mm thick water proof Century Marine ply IS:710, ISI Mark,Termites proof. over 2"x1" aluminium pipe, 1.5mm laminated sheet all complete including all taxes and royalty all complete as per building specification and direction E/I. (Make of Laminate, Plywood and Veneer (710 Marine Grade) Green/Century/Archid or equivalent as per direction of engineer in Charge)

Providing and fixing Window/Door Frame with 12 mm b.w.p block board & plywood CONFORMING TO IS:710 GRADE OF APPROVED MAKE & BRAND (green ply, century ply or equivalentand Pasting with 1.5 mm laminate with material and labour all complete as per building specification and direction of E/I.(710 Marine Grade) Green/Century/Archid or equivalent as per direction of engineer in Charge)

Providing and fixing door shutter wooden framed by both side best quality ply and 1.5 mm thick water proof laminate both side pasting finishing with all material and labour all complete (including all fancy type fitting) as per building specification and direction of E/I.

Providing and fixing Brass Metal antique type Silent Sweep Wall Clocks

Supply and instalation of (Theme Based Painting) with Framing all complete as per specification and direction of E/I.

Supply and instalation of CO2 Fire Extinguisher 4.5Kg all complete as per specification and direction of E/I.

Providing and Fixing Voltas Make Fixed Speed Slimline 3.0 Tr. (Tower) Ac. (R-32 Gas)- 100% Copper. HSN Code- 8415, in the direction of E/I.

Providing and fixing RO,UV Water Purifier KENT GRAND PLUS in the direction of E/I.

Providing and fixing ICO-WHT-LETS36R009XN ESTUS SWIVEL36° 9W NEUTRAL WHITE in the direction of E/I.

Providing and fixing Jaguar Wall Light Square, Gold WL28-10004 in the direction of E/I.

Providing and fixing OCECO Helico light energy saving bldc ceilling Fan (10W Dmmable light ) 5Star 1200mm BLDC motor with Remote control in the direction of E/I.

Providing and fixing Dolphy Automatic Soap Dispenser-DSDR0117

Providing and fixing Dolphy SS Paper dispenser

Providing and fixing Dolphy Toilet Roll Dispenser-DTPR0015

Providing and fixing Automatic Air Freshner Complete Set

Providing and fixing Dolphy SS Cloth Hook-DTPR0020

Providing and fixing Taski Urinal Screen

Providing and fixing 8L Stainless Steel Indoor Trash Can With Foot PedalDWBN0026

Providing and fixing TOTO, THX20MCRB HEALTH FAUCET

Providing and fixing KEROVIT 411005 2 WAY BIB TAP

Providing and fixing KEROVIT 111032 STOP COCK TRIM

Providing and fixing KEROVIT 111031 STOP COCK CONC.

Providing and fixing CONNECTION PIPE CONNECTION PIPE

Providing and fixing TOTO THX1A-6N BOTTLE TRAP

Providing and fixing KEROVIT T6JV6 WASTE COUPLING

Providing and fixing KEROVIT 3027 VITA ONE PIECE (220 MM)

Providing and fixing TOTO LW818JW/F#W TABLE TOP BASIN

Providing and fixing KEROVIT 7027 URINAL

Supplying and placing of 1 SEATER Leather Brown - Mocha Brown Sofa frame made of Kiln-dried solid wood ensures durability Solid wood tapered legs make the sofa look airy and light Breathable genuine leather upholstery feels buttery soft and sumptuous Soft cushioned back and seat for comfortable seating Padded armrests adds to your comfort Curved wooden accent and classic tufting add a timeless appeal Anti-sag construction offers the right level of support for maximum comfort Comfortable seat depth & height, designed for modern Indian lifestyle Dimension (W)920mm X (D)900mm X (H)940mm Assembly Type Knock Down. The product is BIFMA and FSC certified .Warranty-5 Years MAKE DURIAN.MODEL-RADIANCE/1

Supplying and placing order center table -Dimension (W) 800mm X (D) 800mm X (H) 335mm/abletop made of natural marble. Natural variations in the marble veining make each piece unique. Base made of high-quality metal. The gently curved profile in mixed materials adds dimension to your space. 50mm thick tabletop complements the Champagne Gold hued boxy pedestal. The Antique Chrome finish adds a striking contrast with a white tabletop. MAKE DURIAN - MODEL -DOROTHY/CT

Supplying and placing order center table -Dimension (W) 500mm X (D) 500mm X (H) 500mm/abletop made of natural marble. Natural variations in the marble veining make each piece unique. Base made of high-quality metal. The gently curved profile in mixed materials adds dimension to your space. 50mm thick tabletop complements the Champagne Gold hued boxy pedestal. The Antique Chrome finish adds a striking contrast with a white tabletop. MAKE DURIAN - MODEL -DOROTHY/ST

Supplying and placing of VISITOR CHAIR - Dimension (W)570mm X (D)510mm X (H)775mm/Material & Subtype Solid Wood- Rubber Wood,Premium Leatherette Frame Material Solid Wood/Upholstery Material Premium Leatherette. Legs crafted of solid wood in Natural finish. Kiln-dried solid wood construction makes it warp and scratch-resistant. Breathable leatherette upholstery in grey feels soft and sumptuous. Anti-peel family-friendly upholstery, ideal for families with kids & pets. Contouring barrel back, slender arms and soft seat offer comfortable seating experience. The natural brown finish of the wooden frame adds a striking contrast Assembly Type Knock Down. The product is BIFMA and FSC certified -MAKE DURIAN.MODELMELANIE/DC All complete as per building specification and direction E/I

Providing and fixing of 15 mm Solid Teak wood) Wooden floor with matt finish melamine clear polish (Make :- Square feet, Deco foot or Equivalent.) including Labour charge. All complete as per building specification and direction E/I

Supplying and Fixing & Fitting of Kaleen MADE OF SYNTHETIC SHAGGY (6' x 8') All complete as per building specification and direction E/I

Providing and fixing all height wall paneling of 12 mm thick water proof Century Marine ply IS:710, ISI Mark,Termites proof. over 2"x1" aluminium pipe, 6mm PVC louvers all complete including all taxes and royalty all complete as per building specification and direction E/I

Providing and fixing all height wooden celling of 12 mm thick water proof Century Marine ply IS:710, ISI Mark,Termites proof with 4mm veneer. over 2"x1" aluminium pipe and 6mm board. all complete as per building specification and direction E/I. (Make of Laminate, Plywood and Veneer (710 Marine Grade) Green/Century/Archid or equivalent as per direction of engineer in Charge)

LED TV Back Drop Units of Standard Size (varying depth 450 mm to 400 mm) as per the following specification: Supporting system comprising of factory-made 2"x1" rectangular aluminium Chanel of placed vertically & horizontally at 600mm centres. Providing & fixing 19 mm thick BWR Plywood finished to the frames on one side with sheet metal screws. Cladding with wpc louver/leatherette/Texture laminate .Providing & fixing cladding to the walls as per the design enclosed with Tick Beat of approved texture, grains, shade fixed to 12 mm 710 marine grade [Shelves and Drawer units: Providing 75 mm to thick shelves on the Top level and Bottom level of varying depth 450 mm to 400mm. Bottom level to be provided with open draw units of size.(600mm to 800mm) x (450mm to 400 mm depth) x 300mm of Minimum 3 No's of Drawer units 19 mm plywood with 1.5 mm Laminate Providing Hardware i.e., Multipurpose locks, Handles, telescopic channels, Auto Hinges & Heavy-duty magnet catcher’s, Tower Bolts etc. with New Hardware as approved by the engineer in charge. Provision of HDMI cable and necessary strip light as per direction of engineer in charge (Make of Laminate and Plywood(710 Marine Grade) Green/Century/Archid or equivalent as per direction of engineer in Charge)

Providing and fixing Ding Dong wireless Call Bell

Providing and fixing Cunter slab Flower Pot with Artificel Flower

Providing and fixing Decorated antique type besin top Wall Mirror

Supplying and laying corian Soft Maxicon carpet Grass of hybrid best quality including supplying and mixing of vermin compost do--d0--- all complete as per building specification and direction of E/I

Providing and fixing Voltas Make Inverter Hot & Cold One Way 2.0Tr. Cassette Ac. - 100% Copper. HSN Code- 8415, in the direction of E/I.

Providing and fixing 65 INCH LED TV SMAER (QA65S90AUL Samsung) in the direction of E/I.

Providing and fixing STI-WHT-LSTP04X005XW 5W OUTDOR LED STIPLIT WARMIP65(1PACK=5M) in the direction of E/I.

Providing and fixing ZCI-WHT-LDRV01S030XX POWER SUPPLYFOR 5W/PM LED STRIP LIGHT 24V,1A INDOOR in the direction of E/I.

Providing and fixing DCO-GLD-AS11021 COSMOSCHANDELIERWITH ASFOURALMAAZACRYSTAL (D600,H-90MM) in the direction of E/I.

Providing and fixing Jaguar Foot Light Circular, black FL12-80C9 in the direction of E/I.

Providing and fixing WALL HUNG WC RIMLESS WITH DURAPLAST SEAT COVER AND SLIP IN CONN. TOTO CODE - CW162MUNNW1 + TC390CVK + TYX215C

Providing and fixing TOTO MB174P#SS FLUSH PLATE

Providing and fixing TOTO WH132MNF CISTERN WITHOUT FRAME

Providing and fixing TOTO LW4716RE#XW TABLE TOP BASIN

Providing and fixing TOTO UW904VM#NW1 URINAL

Providing and fixing TOTO DUE114UPK URINAL SENSOR

Providing and fixing HAVELLS TROCLA 15L TANK ( geyser )

Providing and fixing TOTO TLG01310B2 WALL MOUNTED BASIN MIXER

Providing and fixing TOTO TLN01301B1 WALL MOUNTED BASIN MIXER CONC.

Add 18 % GST

Add 1% Labour Cess

K & G ASSOCIATES