Renovation of Womens ITI at Khunti, Dist.-Khunti for the Year 2023-2024

Amount

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 6mm cement plaster (1:4) in celling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing two coats of snowcem of approved shade and make over old surface including washing cleaning and preparing the walls, scaffolding , curing and taxes all complete as per building specification and direction of E/I.

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I. With commercial grade white 15X15cm Tiles.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter.

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Bend - 110mm

Shoe - 110mm

Supplying fitting and fixing glass panes including supplying putty. Beads and nails after taking out old and broken glass panes and disposal of debris all complete as per building specification and direction of E/I. 4mm plain

Easing and adjusting door and window shutters with chaukhats in old work complete as per specification and direction of E/I.

Suppling fitting and fixing oxidised iron fitting of approved quality and make to doors and windows all complete as per building specification and direction of E/I.

100mm butt hinge

250mm Tower bolt

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.

15mm Dia

20mm Dia

25mm Dia

Providing and fixing male ended 15mm dia brass bib cock of approved quality (weight not less than 350grams with extra socket all complete as specification and direction of E/I.

Providing and fixing brass / C.I Stop cock of approved quality all complete as per specification and direction of E/I.

Brass Stop Cock - 15mm Dia

20mm Dia

Supplying fitting and fixing the following items complete with all materials as per specification and direction of E/I.

Glass self with C.P. brass rail 600 x 125mm

Mirror of 4 mm thick plate glass mirror with hard wood backing or 3mm ply wood board 600 x 450 mm

C.P. brass towel rail 20 mm x 600 mm with bracket container

C.P. brass liquid shop container

Supplying labours , tools & tackles for cleaning filled and choked man hole , septic tank , inspection chamber ,gully pits ,sewerage tank etc in all lifts and disposal of spoils up to a lead of 50 meter all complete as specification and direction of E/I.

Supplying, fitting and fixing vitreous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on painted C.I. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350gms, 32mm P.V.C waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.

Supplying, fitting and fixing 40 mm high vitreous white glazed earthen ware E.W.C. with ‘p’ trap of Parry Hindustan or any other I.S.S make including supplying & fixing 15 liters C.I mosquito proof low down flushing cistern of approved make with complete fitting with C.I handle and R.S or bracket with telescopic flush pipe with brass coupling and plumbers joints spindles stop cock of approved quality weight not less than 450 grams, 15 mm P.V.C alkathene pipe 45 cm long with brass coupling at both ends and white/black plastic solid state seal and lead of commander/cuckoo or other I.S.S make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. EWC with S trap with 12.50 litre low level CI cistern

Supplying, fitting and fixing flat back or angular lipped front vitreous white glazed earthenware urinal of “Hindustan” “Parry” or any other approved I.S.S make with 5 liters capacity C.I. automatic flushing cistern of reliance for any other I.S.S. approved make with all fitting with C.I or R.S brackets, standard size G.I flush pipe with fitting clamps, 15 mm C.I body brass spindle stop cock of approved quality weight not less than 400 grms,15 mm P.V.C alkathene pipe 450 mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with 2 coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/I. Flat back or standing corner (450 mm x 350 mm)

Supplying, fitting and fixing viterous white glazed earthen ware indian squating type 600 x 350 mm urinal plate of Parry Hindustan or any other I.S.S. approved make with internal flushing rim 100 mm white glazed earthen ware channel about 1m long 5litre capacity C.I. automatic flushing cistern of reliance or any other approved make with fittings C.I. or R.S. brackets 15 mm & 45 cm long P.V.C. alkathene pipe standard G.I. flush pipe for back and front with spreader fitting and brass coupling etc. 15mm C.I. body brass spindle stop cock weight not less than 450 grms. all complete including painting of exposed part with 2 coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/l. 600 mm x 350 mm size large

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. 450 mm long with 12.5 lit. low level C.I. Cistern

Supplying, fitting and fixing H.C.I. pipes with ear of approved make confirming to I.S.I-1729 including supplying nails and bobbins shorts pieces, cutting loose collars lead and yarn for making lead caulked joints, cutting pipes of size including earth work or scaffolding where necessary etc. all complete as per specification and direction of E/I.

100mm Dia

75mm Dia

Supplying and fixing H.C.I fittings of approved make confirming to I.S.S. 1729 including supplying nails and bobbins lead and yam for making lead chaulked joints including earth work or providing scaffolding as the case may be all complete as per specification and direction of E/I.

H.C.I Single junction with door & ear except socket 100 mm dia ( Wt. 10.50 kg Approximate )

80 mm dia (Wt. 7 Kg)

H.C.I Heal Rest Bend 100 mm dia ( Wt. 5.5 kg App.)

80 mm dia (Wt. 4 Kg. app.)

H.C.I double junction with door and ear 100 mm dia ( Wt 15.5 kg App.)

80 mm dia (Wt. 8.5 Kg. app.)

H.C.I bend with door and ear 100 mm dia (6.50 kg App.)

75 mm dia (Wt. 4.5 Kg app.)

Floor trap with gratings 100 mm dia

H.C.I plain bend with door and ear 100 mm dia (6.50 kg App.)

75 mm dia (Wt. 4.5 Kg app.)

Supplying materials and labour for painting the exposed H.C.I. pipe and fitting with two coats of approved paint over a coat of red oxide primer etc all complete as per specification and direction of E/I.

100mm Dia

80mm Dia

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 250X20X6mm L-type M.S clamp properly fishtailed, including maiking holes and setting as same in 250X125X75mm. Cement concrete block (1:2:4) with cost of all labour and materials and taxes as per building specification and direction of E/I.

Providing primer one coat of red lead paint of approved make over new steel surface & Providing two coat of synthetic enamel paint of approved shade and make over steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over old wooden surface including cleaning the surface after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing.

Carriage of materials from nearest approved sourses of supply including loading into trucks and unloading from truck and stacking properly at work site etc. all complete job as direction of E/I.

a) Bricks lead up to (1 K + 7P) 8K.M

b) Sand lead up to 8 K.M

c) Stone Metal lead up to 20 K.M

d) Stone Chips lead up to 20 K.M

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A&B) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. Extra for earthwork in hard soil as per specification and direction of E/l (vide classification of soil item-B)

Earth filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I.

Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for - Foundations, footings, bases of columns, etc. for mass concrete.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Providing designation 75 A brick work in C.M. (1: 6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

providing Tor steel reinforcement of rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL)

12mm Dia

8mm Dia

10mm Dia

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper scaffolding , curing and taxes all complete as per building specification and direction of E/I.

Supply of Angle 50x50x6mm per post with all complete job.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Dismantling barbed wire fencing with ballah or angle iron post including stacking all materials in countable stacks within 15M lead all complete as per direction of E/I.

Jungle clearance in borrow area, building premises, flanks and slope on the road, canals and embankment by removing the grass and jungle bushes from the top including weeding out shrubs small trees upto 150 mm dia. and their removal all complete job as per direction of E/I.

Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth, watering and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Dismantling R.C.C. work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of all colour and texture except black, Cherry/ Ruby red

Supplying, fitting and fixing M.S. grill gate with M.S. grill made of 20X6mm M.S. flats or 16mm M.S. square bars fitted on 25X25X6mm M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.

Providing designation 75A one brick on edge soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing desination 75A brick on edge flooring in cement mortar (1:4) with top surfaces flush pointed in cement mortar (1:4) with approved quality of sand including the cost of curing,taxes, royality all complete as per building specification and direction of E/I.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Cost of Driled 200mmx165mmx125 mtr deep bore well in all kind of soil and rock in rural area for instalation of pump set with Hydrolic DTH rig machine all complete including all materials, tools, drilling , air compressure and equipments well as fule, lubricans and cost of trsportation of rig machine and other vehile up to site.

a) From 0.00 M to 50.00 M Below G.L.

b) From 51.00 M upto 150.00 M

Supplying assembling lowering and fixing in vertical position in bore well, unplasticised pvc medium well cashing (cm) pipe of required dia conforming to IS:12818,including required hire and labour charges,fitting & accessories etc.all complete for all depths as per direction of engineer -in- charge.150mm nominal size dia

Development of tube well in accordance with IS: 2800(Part I) and IS:11189,to establish maximum rate of usable water yield without and content (beyond permissible limit) with required capacity aircompressore running the compressore for required time till well isfully developed measuring yield of well by "v" notch method or any other approved method, measuring static level &draw down etc by step draw down method ,collecting water samples & getting testeding approved laboratory i/c disinfection of tubewell all complete including hire &labour charges of air compressore,tools &accessories etc.all as per requirement and direction of engineer-in- charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing /cashing pipe removable as per requirement all complete for borewell of : 200mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part - I) including necessary bolts & nuts of required size complete. 200mm clamp

Supplying, submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft ad polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3 HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufaturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP.

Supplying full automatic star selta starter to operate induction motor working on 415V 3 phase 50Hz with no coil. Over load element, On _ OFF push botton with necessary materails and connection to supply etc complete starter with original sheet steel encloser as per 3914. F.A.S.D. starter up to 5 H.P

3 core PVC insulated PVC sheathed copper conductor flat submersible cable. Supplying, Flat Flexible submersible cable with, copper conductor, PVC insulated and PVC sheathed as IS : 7098. 3 core 4 sq.mm copper wire

Supply, fitting and fixing GI pipe 50 mm Dia (TATA or equivalent make) Medium Quality as per IS : 1239 (part 01) 2004

Wiring for light point / exhaust fan point / call bell point with 1.5 sq .mm FRPVC insulated copper conductor single core cable in surface / recessed PVC Conduct, with piano type switch, phenolic laminated sheet, suitable size PVC/G.l. box etx. As Required

Group B

Group C

Supplying and fixing following piano type switch / socket on the existing switch box/cover including connections as required.

5/6 amps , one way switch

3 pin 5/6 amps , socket out let

Wiring for light/ power plug with 2x4 sq.mm FR PVC insulated copper connductor single core cable in surface/recessed PVC conductor single core cable for loop earthing as required.

Wiring for Circuit / submain wiring along with the following size PVC / insulated copper conductor single core cable in surface/recessed PVC conductor single core cable for loop earthing as required.

2x2.5 sq mm+1x2.5 sq mm earth wire

2x6.0 sq mm+1x6.0 sq mm earth wire

Supplying and fixing suitable size G.I /PVC box surface or in recess with phenolic liminated sheet cover in front including provideng and fixing 6 pin 15/16 amps socket out let and 15/16 amps piano type switch in connection painting etc as required.

Supplying & fixing 6amps to 32 amps rating 240 volts "B" series miniature circuit breaker suitable for lighting and other loads of folloing poles in the existing MCBDBcomplete with connectiontesting and commissioning etc.

6/32 amps, single pole,"B" series

40 amps, single pole,"B" series

Supplying & fixing following way single pole neutral sheet MCB distriution board 240 volts on surface / recess complete with tinned copper busbar neutral busbar earth bar din bar detachable gland plate interconnection phosphatized powder painted with complete job

8 Way Single door

Providing and fixing following capacity TP&N disconnector fuse switch unit inside the in existing cubicle panel board with ISI marked HRC fuse including drilling holes in cubicle board making connection etc.

63 amps ,TP&N

Supplying & fixing following rating TP&N 415 volts residual current circuit breaker having a sensitivity current upto 300 milliamperesr in the existing MCBDB complete with connection testing and commissioning etc.

Installation testing and commissioning of of Ceilling fan including wiring the down rods of standard length (upto 30 cm ) with 1.5sq mm FR PVC insulated copper conductor single core cable etc.as required.

Earthing with G.I. earth pipe 4.5 mtr long 40mm dia including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc with charcoal and salt as required.

supplying and fixing 8SWG copper wire at 0.50 mtr below ground level for conductor earth electrode including soldering etc as required.

Providing & Fixing of lighting conductor final made of 25mm dia 300mm long copper tube having single prong at top with 85mm dia 3mm thick copper base plate including holes etc etc as required.

Reverting sweating and soldering lighting conductor taps /G.I taps as required.

Providing & Fixing of G.I tape of 20mm dia 3mm thick on parapet or surface of wall for lighting conductor etc etc as required.

Providing & Fixing of G.I. tape of 20mm dia 3mm thick on parapet or surface of wall for lighting conductor etc etc as required.

Supplying fixing of exashust fan complete job

S.I.T.C. of Floowing rating surface Mounted LED Tube light fitting suitable for 230V 50 Hz, single phase supply etc. Complete as required 10/12W LED Tube Light

S.I.T.C. of Floowing rating surface Mounted LED Tube light fitting suitable for 230V 50 Hz, single phase supply etc. Complete as required 20/22W LED Tube Light

Supplying 9/10W LED Bulb

Suppying and Fixing 2 pin 5 amp Ceiling rose on the existing junction box/wooden block including connection etc. as required

Supply installation testing and commissioning of follwing size ceiling fan 3 blades confirming to IS: 374 : 2019 including wireing the down rods of standard length (up to 30cm) with 1.5sq mm FR PVC insulated copper wire suitable for 230V 50Hz single phase suppy etc. complete as required 1200mm (48") ceiling Fan

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing designation 125 mm thick reinforced designation 75A brick work in CM (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 25 including the cost of screening, carriage of materials, scaffolding , raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Suspended floors, roofs, landings, balconies and access platform.

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lift as per building specification and direction of E/I.

S/L/F C.I Cover with frame for manhole & inspection chamber complete job.

Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing 25mm thick first class patent stone flooring (1:2:4) with stone chips in two layers, bottom layers 19mm. Thick (1:2:4)with 12mm to 6mm. Size graded stone chips and top layer 6mm. Thicks (1:2) with 6mm down stone chips, in panels including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes and royality with all complete as per building specification and direction of E/I.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size)

Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately)

Add 18 % GST (in Basic Rate must fill 12)

Add 1% Labour Cess (in Basic Rate must fill 1)

M/S AMARJEET MISHRA

M/S DREAM WINGS INTERNATIONAL