Supply, installation, testing and commissioning of electro-mechanical equipments and construction of pump house/panel room/ operator room at water supply scheme Dadasara

Amount

(Part A: Electro-Mech.) WSS Dadasara (Adv. Cost Rs. 53,45,000/-)

Supply, Installation, Testing & Commissioning of Submersible Pumping Unit as per IS 8034 with following specification are as under : PUMP : Efficiency = Not less than 50% Speed = 2900 Rpm Type of pump = Mixed flow. Type of fluid to be handled = Clear Water MATERIAL OF CONSTRUCTION: Impeller = Stainless Steel Pump Shaft = Stainless Steel SS 410. Pump Casing = Cast Iron/Stainless steel. rest specifications are as per Cluase - 1 of SBD. capacity of Motor = 12.5 HP

Providing/supplying and fitting of G.I flanged Rising Main at site. Rest Specifications as per Cluase -"8" of SBD The size of the G.I is given below ' Size : DN 100 Class: C (Heavy)

Earth work in excavation by manual means in trenches for foundation, drains, pipes, cables (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and reaming of bottom lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed. (All kinds of soil 01 meter from cutting edge)

Filling available excavated earth in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by reaming and watering, lead upto 50 m and lift upto 1.5m.

Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked material in all kinds of soil

providing and laying of stone soling including manual compaction

Centering and shuttering including strutting , propping etc. and removal of form work for Foundation , footings , bases for columns

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering . all work upto plinth level with 1: 2 : 4 mix ( 1 cement , 2 coarse sand , 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade of reinforcement cement concreteincluding curing but excluding the cost of centring and shuttering . finishing and reinforcement all work upto plinth level with 1: 1.5 : 3mix ( 1 cement , 1.5 coarse sand , 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering . all work upto plinth level with 1: 3 : 6 mix ( 1 cement , 3 coarse sand , 6 graded stone aggregate 40 mm nominal size)

12, mm thick cement plaster of mix 1:4 (1 cement : 4 fine sand)

Steel reinforcement for RCC work including straightening, cutting, bending, placinng in position and binding all complete upto plinth level Thermomechanically treated bars of grage FE-500D or more

Fabrication, providing and fitting of split type MS clamps 10 mm thick, 2 ft long and 3 inch wide for lowering and holding of pumping unit fitted. The job includes the cost of required size of nuts and bolts. Size: 100mm

Fabrication ,Providing and fitting of 90-120 degree bend/elbow to be fabricated out of G.I pipe, 1 m length and flanged on both ends a to make it leak proof. The flanges shall be M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) and welded on both sides. The job includes nuts, bolts, gaskets etc as per site requirement. Size:DN 100 Class: C

Cutting of hot dip galvanized G.I, pipe across the section by dint of pipe cutter/ gas cutter. The job also includes Providing and welding of M.S flanges to the two ends of pipe. The Thickness of flange shall conform to IS 6392 Part 1st Table-17. The flange welding shall be carried out in double layers using Advani/Esab/L&T- SS Bond make electrodes to form strong welding joint by dint of DC arc welding. The job further includes Providing and Fitting of nuts and bolts (conforming to IS:1363 Part 1st) and Rubber Insertion Gaskets (conforming to IS: 638/79) to be used between flanged joints. The size of the pipe is DN 100 , Class-C

Fabrication, providing and fitting of washout Tee with arm length 1.2 feet each. The Tee shall be fabricated out of G.I pipe with M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) fastened with weld joints on three ends. Size: 100 mm Class: C class

Providing and fitting of ductile iron duoble flanged , Non-rising spindle soft seated gland less gate/sluice valve . Rest Specifications as per cluase -"12" of SBD . The size of the valve is given below size = DN 100, PN 1.6/16

Providing and fitting of Ductile Iron NRV, rest specifications as per Cluase "13'' of SBD . The size of Valve is given below Size = DN 100, PN 1.6/16

Providing, fitting, testing and commissioning of DN 50 , PN 1.6/16 diameter ARV (Air Release valve), Rest specifications as per Cluase "14'' of SBD .

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses, construction of liner etc. including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer , including welding and bolted with special shaped washers etc. complete

Providing and fitting of M.S 4 inch hinges -6 no and M.S handle heavy -8no., Anchor bolts with nuts (M16) of 0.3 m long = 04 No. Metallic strip (350mm×50mm×3mm) = 02 No.

Fabrication of gantry mechanism/CGI Shed /angle iron sleeping bed by way of providing Structural steel in built up sections , trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete welded

Providing, installation and testing of manual type triple spur gear chain pulley block along with monorail geared travelling trolley having following features. Gears:- The hoist shall have precision machine case Hardened alloy steel gear mounted on bearings and housed in a dust proof gear box. The lubrication of gears should be of high viscosity and temperature for longer life of gears. Load Chain:- The load chain be made of high tensile alloy steel having wear resistance and greatest mobility. The chain should be accurately collaborated, tested and have adequate in built factor of safety for safer operation. Load chain wheel:- the load chain well should be double ball bearing supported and Specially designed, perfectly machined wheel providing correct grip of load chain to makes the hoist most safe and reliable against any failure. The main specifications of C.P Block are given below : Make = Reputed make Capacity = 3 ton No. Of load chain falls = 2 or above Min. Height of lift = 6 M

Providing, installation, testing and commission of 63 KVA HT Transformer, 3 phase (Level 2). Complete specifications as per cluase - 26 of SBD.

Providing and fitting G.I Channel /Angle/ Flat of sizes including clamps

Supply, Installation, Testing and commissioning of Polymeric Gang operated Air break switch, outdoor type, triple pole, suitable for vertical installation, single break provided with locking arrangement at both ON and OFF position consisting of HT post double insulator, copper or copper alloy high pressure heavy contact assembly, rod with bearings , operating handle and 2 length of 32mm dia. GI pipe conforming to IS 1818 1961, 06 No. of insulators, rated voltage 11KV 200A complete as per IS specs.

Supply, Installation, Testing and commissioning of 11KV polymer fuses Set Horn Gap 3-phase 200 A suitable for vertical installation

Supply, Installation, Testing and commissioning of Gapless Surge arrestor station class, 10KA, 9KV, LA With polymer housing , Station Type .

Supply and fitting of 11 KV polymeric composite pin insulator 12 KV, 5KN, Lighting impulse 75KV Positive, and 80 KV Negative , creepage distance 320 mm

Supply, installation, errection of 9 mtrs long H.T pole of specifications ST- 410 (sp-33) . The job further includes drilling of holes for installation of various accessories .wherever required. The job further includes GI wire earthing of pole as per REC standard.

P/F of Galvanized nuts, bolts of various sizes as per site requirement.

P/F Danger Plate with clamps

Providing and fixing G.I Barbed wire for anti climbing

Providing and fixing of anti climbing devices with clamps

Providing and fitting of Galvanized stay set with 50 X 8 mm Stay Clamp , Guy insulator (2no.), Anchor plate (200X200X6mm) , nuts and bolts , 2 N0- turn buckle , 1.8 m long , 16 mm diameter solid G.I stay rod & 7/3.15 mm dia. G.I stranded wire complete.

Painting of poles Red oxide

Painting of poles Aluminum paint

Providing and fitting of ACSR as per IS 398 (part-2) 1996 for 50 sq.mm ACSR (Galvanised steel reinforced) for fitment of various accessories

Supply, Installation and Testing of 35 Sq mm XLPE Aluminum H.T cable (ABC type ) of 11 KV grade with following specs. Size (cross sectional area in sq mm) = 3×35 with reinforced wire Phases: Red, Yellow, Blue

Providing and fitting of Anchoring clamps comprising clamp body , plastic wedge, steel bill bracket , straps and buckles or nuts and bolts required for holding of 3 – Core , 35 Sq. mm H.T AB Cable.

P/F of 11 KV cable termination kit for connecting 35 Sq mm XLPE cable (ABC type) with the existing HT line near tapping point and HT transformer.

Providing and fitting of LT Distribution box for HT transformer with MCCB For incomer and SFU for out going circuits . Capacity of transformer: 63KVA

Fabrication, Providing and fitting of MUG-15 Modular motor control panel of appropriate size fabricated out of 14 SWG sheet having required openings/vents and protection Class : IP-55 & fitted with accessories as under: Complete specifications as per Cluase- 43-C of SBD

Providing, fitting, testing and commissioning of voltage stabilizer as per specifications below: Complete specifications as per Cluase- 44 of SBD Rating::30KVA

Providing and fitting of 3-Core flat submersible copper cable conforming to IS: 694 (Part 1st) – 1964 & IS: 694 (Part 2nd) - 1964 for Submersible Pumping Unit and other electrical Equipments . The cable connections terminal shall be fitted with copper thimbles of required size. Size: 10 sqmm

Providing and Fitting of 3 /3.5/2-Core, XLPE Armoured Aluminium Cable conforming to IS: 7089 part 1st as service line from the HT transformer to control panel including necessary thimbling, crimping, taping etc. NOTE:- The cable terminal ends for connection to switchgear at various requisite points shall be Al. Thimbles of dowel’s make and of appropriate size and connected by hydraulic crimp tool only. i) 50 sqmm, 3.5core, LT, 1.1 KV

ii) 10 sqmm, 2 core, LT , 1.1 KV

P/I of earthing station for substation, LT panel, DG set and stabilizer comprising of company fabricated earthing electrode as per IS: 3043. The job includes Auguring of bore of required dia/depth for installation of electrode along with backfill compound mixed with soil and all other items required thereof for achieving the best result. The job includes connecting of electric gadgets through GI strip as per relevant standards. Safe earthing electrode size : 80 mm dia , Length : 2000 mm Back fill compound : 30 kg

Supply, installation of 6 kg co2 type fire extinguisher manufactured as per IS:15683 OF 2006 with IS mark and comply with DGMS(Approval) . The co2 extinguisher should be suitable for class B & C fire and also for fire involving electrical equipments. the cylinder used for fire extinguisher shall be approved by protroleum and explosive safety organization(PESO) as per gas cylinder rules 2004 and as per IS: 7285 of 2004. The body should be made of seamless steel (manganese) confirming to IS:7285 with IS mark and should be provided with squeeze grip nozzle and should be filled with co2 confirming to IS : 15222 of 2002 with certificate. The extinguisher shall be provided with manufactures test certificate and hydraulic test certificate by BIS from PESO.

Illumination of Premises: Providing and erection of 9 Mtr long Hot Dip Galvanized octagonal pole (single Section) with bottom 150mm, top 75mm wide, thickness 3mm with 70 Microns Zinc coating having inside arrangement for providing of power connection along with following items. rest specifications as per clause- 50 of SBD

Providing, installation, testing and commissioning of area lighting 120 Watt LED (Street Light Type) on top of octagonal pole vide item No.36 Having following specs: Input: 90-240 V 50 Hz Power Factor: >0.9 Colour Temperature: 4K - 6.5K Beam Angle: 120˚ - 170˚ Lumens: >12000 Operating Temperature: -20˚C to 60˚C The LED is pressure die cast aluminum housing with power coated finish and having Ingress Protection up to IP-68. The LED is to be properly fitted on the arm of the pole and connected to the copper wire as directed.

Providing, Installation and testing of 2KVA fully automatic voltage stabilizer with input voltage 70-240 V and output 220 V. The stabilizer shall be installed and connected to the electric circuit as per location provided by site incharge.

Supply, installation, Testing & commissioning of 1000VA Full Sine wave power inverter (Make: Reputed) including Providing / Installation of 12V, 180AH Tubular inverter Battery with trolley and cover. (Make: Reputed) with 2-core 6mm2 Cu wiring as per site requirement along with other accessories like SS-Combine (02 No’s), 3-pin plugs etc of reputed make for proper fitment and installation of the item.

Providing, laying & fixing with adhesive/bonding material of insulation rubber mats on the floor of the pump house, covering area around electro-mechanical machinery for safeguarding the life & limb of the workmen due to possible leakage of current & short circuit. The floor surface shall be made good & shall be free from dust, grease, foreign material & moisture free. The mats shall be as per IS 15652:2006 & shall have the following specifications: - Composition: Rubber (synthetic mats for electrical purpose) Thickness: - 2.5mm Size: - 1M wide. The rubber mats shall be accepted with manufacturers test certificate.

TOOL KIT For Maintenance: - The Tool Kit for maintenance shall comprise of the following and all the items as mentioned below shall be of : Providing of tool kit consists of following items Rest specifications as per clause - 56 of SBD

Providing and fitting of 19 mm thick multilayered ply sheet of size 6 x 3 feet , 2 nos including cutting , fixing all complete including painting of the play sheet by one coat of primer and two coats of enamel paint

Providing of good quality bedding for night stay/Shift consisting of: - i) Mattress with warm cover size 6'x3' (6Kg)- 02 No’s ii) Quilt with warm cover size 5'x8' (6Kg)- 02 No’s iii) Pillows with covers - 02 No’s iv) Single bed warm blankets with one sided Fur- 02 No’s Rest specification as per clause - 57 of SBD

Providing of solar/ electrical lantern chargeable on both solar & electrical 220v supply.

Providing of bamboo ladders 18 feet long along with 15 feet long Link rods and HT Glove pair (01 No each)

Providing of 1 KW heat convector for operators for winter season.

Providing and fitting of 01 No. LED (scroll type) sign board fabricated out of stainless steel and metal showing the names of water supply scheme and the Department. Size: 6’×1’6”

Providing and fitting of 01 No. angle iron/sheet metal board duly painted showing various specifications of the mechanical and electrical equipments installed at site.

Providing corrugated G.S Sheet roofing including vertical/ curved surface fixed with polymer coated J or L Hooks , bolts and nuts 8 mm dia. diameter with bitumen and G.I limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete ( upto any pitch in horizontal /vertical or curved surface) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.50 mm thick with zinc coating not less than 275 gram/m2

Providing, cutting , fitting and welding Green PVC Coated welded wire fence with Square mesh -4 and wire diameter 1.5 mm to be fitted on all open vertical sides of the D.G Set shed . The job includes cutting, welding, hoisting etc as per site requirement.

Providing, installation, Testing & commissioning of 415 ±10%V (output), 3 phase Diesel Generator set as per IS 8528 (2018) and ISO 3046 (2002) for engine and IEC/IS 60034-1 for alternator suitably assembled and fitted in a pollution free acoustic enclosure / canopy of required size as per Ministry of Environment protection rule 1986 read with latest amendments. The DG Set is required to be fitted and tested on load at site The D.G Set shall have the following technical specification. Besides the above works the D.G set shall be provided with 12 V, 150 AH Lead acid battery of reputed make fitted inside the D.G set Canapy along with necessary accessories and battery charger of required capacity. The job also includes the cost on account of HSD and skilled operator required for operation of D.G set for a period of 10 hours continuously during its testing and commissioning of D.G set at site. the capacity of the D.G set is given below: Rating: 30 KVA , Air Cooled.

Providing and fixing of PUF Enclosure in Walls, Ceiling ridges etc made up of 60 mm thick rigid PUF, CFC free with profile surface on one side, conforming to IS-12436-88 with subsequent amendments having density of 40±2 kg/m3 sandwiched between 0.5 mm pre-painted Galvanized steel sheet as per IS-14246-95 with subsequent amendments with 18-20 microns of Exterior Polyester Coating of white color on epoxy primer on both sides. The basic substrate is Gr-120 Hot dip Galvanized steel. The panels are made by continuous line and are joined together by means of Tongue-n-groove joint system. The joints shall be air-tight by using proper sealant (like silicon PU foam etc). The PUF panels have closed cell content of 90-95%; Thermal Conductivity of 0.023 at 10W/mK; Compressive strength of 2.1 Kg/m2 (at 10% deformation); Water vapor permeability 0.08-0.12 gm/h_m2; Self-extinguishing fire property make: confirming to IS Code

Providing ridges or hips of width 60 cm overall with plain G.S sheets fixed with polymer coated J- Or L- hooks , Bolts and nuts 8 mm dia. G.I limpet and bitumen washers complete 0.63 mm thick with zinc coating not less than 275 gram/sq.m

Providing and fixing plain eaves boarding 2nd class Kail wood ( 250 x 32 mm nominal size)

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto .5 m in -All kinds of soil

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) powder coated aluminum (minimum thickness of powder coated 50 microns)

Providing and fixing 12mm thick pre laminated particle board flat pressed three layer or graded wood particle board (conforming to IS:12823 Grade-I type-II) in paneling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

Providing and fixing aluminum casement windows fastener of required length for aluminum windows with necessary screws etc. Complete Powder coated minimum thickness 50 micron aluminum

Providing and fixing aluminum round shape handle of outer dia 100mmwith SS screws etc. Complete as per direction of Engineer-in-charge Powder coated minimum thickness 50 micron aluminum

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in-charge. With floating glass panes of 4.0 mm thickness (weight not less than 10.00 kg / sqm)

Carriage of sand, stone aggregate by mechanical transport including loading, unloading and stacking (average distance-5km)

Carriage of soling stone by mechanical transport including loading, unloading and stacking (average distance-5km)

Carriage of cement/steel/CGI sheet/GI pipes below 100mm dia and other heavy materials by mechanical transport including loading, unloading and stacking (average distance -25Km)

(Part B) Pump House of WSS Dadasara (Adv. Cost Rs. 14,75,000/-)

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: All kinds of soil (1 meter from cutting edge).

Providing & Laying of stone soling (dully hand packed)including watering dressing and ramming with all carriages loading un-loading and stacking etc complete

Providing & laying in position cement concrete of specified grade excld. The cost of centring and shuttering all work upto plinth level(1:4:8 coarse sand 40mm nominal size crushed stone agg.)

Providing & laying in position cement concrete of specified grade excld. The cost of centring and shuttering all work upto plinth level(1:3:6 coarse sand 20mm nominal size crushed stone agg.)

P/L in position specified grade of reinforced cement cencrete excld. The cost of centring, shuttering, finishing and reinforecement-All work upto plinth level. 1:1.5:3 graded stone agg. 20mm nominal size

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°,landings, balconies, shelves, chajjas, lintels, bands,plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate)

Brick work with FPS bricks of class designation 75 in foundtion & plinth in cement mortar 1:6 (1 cement, 6 coarse sand)

Extra for brick work in super structure above plinth level upto floor V Level (by manual means)

Centring and shuttering incld. Strutting, proping etc & removal of form work foundation

Walls any thickness

Reinforcement for RCC work incld straightning, cutting, bending, placing in position & binding all complete (Thermo-mechanically treated bars)

Providing wood work in frames of doors, windows, clerestory windows & other frames, wrought framed & fixed in position 2nd class kail wood

Providing & fixing panelled or panelled & glazed shutters for doors & windows and clerestory windows including ISImarked black enamelled M.S Butt hingeswith necessary screws excluding panelling Second class Kail (imported wood) 35mm thick

Providing & fixing decorative plywood B/S decorative veneer (Type 1) confirming to IS 1328 BWR type

Structural steel welded in built up sections, trussses and framed

Providing CGS sheet roofing fixed with polymer coated J or L hooks bolts & nuts 8mm dia with bitumen & GI limpet washers upto( a pitch of 60 degree) excld cost of perlins, rafters & tresses 0.63mm thick with zinc coating not less than 275g/sqm

Providing ridges of hips of width 60cm overall width plain GS sheets fixed with polymer coated J or L hooks bolts & nuts 8mm dia GI limpet & bitumen washers complete 0.63mm thick with zinc coating not less than 275g/sqm

12mm Cement Plaster on the rough side of single or half brick wall of mix 1:6(1 cement:6 fine sand)

Distempring with oil bound washable distemper of approved brand & manufacture to give an even shade New work (2 or more coats)over and incld. Priming coat with cement primer

Painting with ready mixed Synthetic enemal paint or approved brand & manufacture in all shades to give an even shade NEW steel work (Two or more coats)

Finishing walls with water proofing cement paint of approved brand and manufacture &of rqd shade to give an even shade New work (2or more coats)applied @3.84kg /10sqm

Providing glass panes 10kg/sqm (4mm thick)windows and clerestory window shutters (Area of opening for glass panes excld portion inside shall be measured)

Cement Concrete flooring 1:2:4 (1 cement: 2 coarse sand: 4 graded stone agg) finished with a floating coat of neat cement incld. cement slurry but excld the cost of nosing of steps etc complete 50mm thick with 20mm n/s stone agg crushed

Providing and Fixing glass strips in joints of cement concrete floors 40mm wide and 4mm thick

Providing & fixing of 40x5mm flat iron hold fast 40cm long including fixing to frameswith 10mm dia bolts nuts &wooden plugs and embedding in cement conc block 30x10x5cm 1:3:6mix (1cement:3coarse sand:6 graded st agg)20mm nominal size

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed, consolidated and grouted with fine sand including finishing the top smooth

Providing & fixing Hardware items complete 150 mm Tower Bolt

150 mm Handles

L Drop

Dry rubble masonry with hard stone in foundation & plinth using quarry stone with bond stones

Providing and fixing soil waste pipes (10Ft Long) 100mm dia PVC B Class

Providing and fixing vent pipes 100mm dia PVC B Class

PVC colour 100 mm

P/F of PVC floor trap with Jali

Providing and fixing G.I pipes B Class 20' Long compleate with G.I fittings including all necessary fittings like Sockets, Tee, Reducer etc15mm dia nominal bore

Providing & fixing water closet squating pan (English W.C Pan)with 100 mm and PVC "P"or "S" trap 10 ltr low leavel P.V.C flushing cistern of app make with manually controlled device with fittings Long Pan pattern white vitreous china W.C pan 580mm

Water storage tank PVC tripple layer of approved brand with all necessary fittings

Stain less steel heavy duty Bib cock long nose

Stain less steel heavy duty angle valve

PVC connections

P/F man hole cover with frame

P/F lighting points/Heating Pointsfan points with 1.5 sqmm/4 sqmm FRLS PVC insulated copper conductor in surface/recessed medium class PVC conduit with modular switch, modular plate suitable GI box all complete Heating points

Lighting Points

Carriage of Materials By MT Stone agg. from for an avg lead of 20 km

Sand from for an avg lead of 20 km

Bricks from for an avg lead of 25 km

S T ELECTRICAL ENG WORKS PEERNAR TRAL