ADDN ALTN TO BLDG NO T 19 51 63 64A AND T 21 AT 6 TTR PONDA GOA

Amount

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) & removing rubbish outside MD land.

M & L 50mm thick cement concrete 1:3:6 type C1 using 20mm graded stone aggregate, finishing the surface even and fair as in plinth protection and similar work.

Demolition of existing cement concrete (reinforced) of any type and in any position not otherwise specifically provided for & removing rubbish outside MD land.

M & L for RCC (Nominal mix) type B-0 using 1:2:4 12.50mm graded aggregate as in slabs supported on wall, beams and columns in floors roofs, landing, balconies, canopies , deck slabs and in shelves etc and the like.

M&L TMT CRS steel bars 8mm dia, cut to length, bent to shape reqd and welded to existing reinforcement of any description and any position of RCC structure after binding with mild steel wire annealed n less than 0.9 mm dia.

M&L TMT CRS steel bars 10mm dia and over, cut to length, bent to shape requred, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

Taking down chowkat/frame with shutters n exc 1.5 Sqm (without taking off shutters from the frame) & removing clear off site after credit for the same is recovered by the Dept

All as in item No. 7 above but exc 1.5 Sqm but n exc 4 Sqm each with shutters (without taking off shutters from the frame)

M & L 2nd class hard wood for Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints.

S & F 2nd class hardwood 35mm thick glazed and skeleton shutters(Factory made), open rebated and prepared to receive glass, gauze etc, (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.(Sizes of members of shutters as specified in SSR Pt-I Section 8, clause 8.24(b).

S & F 35mm thick (Factory made) 2nd class hardwood plain framed, panelled shutter (two or three panel) with lock rail and panel of 9 mm BWP commercial ply or 12mm veneered particle board with commercial veneering on obth faces. The size of rail and stile as per IS 1003 (Part -I) kiln seasoned and chemically pressure treated.

Supply and fix solid PVC door frames of size 50mm x 47 mm made out of 5 mm thick plain/printed coloured PVC sheet reinforced with MS square tube all as per specification & drg in SSR Pt II 2020 complete all as specified and directed.

Supply and fix factory made solid panel PVC door shutter 30mm thick (styles) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC "C" Channel having a PVC sheet strip of 20mm width stuck inside with solvent cementfor styles & plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitten in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading & jointed together with solvent cement, complete all as specified and shown in drgs in SSR Pt II 2020 complete all as specified and directed.

S & F aluminium powder coated barrel tower bolts of extruded section 150 mm long.

S & F Aluminium alloy powder coated sliding door bolt 300 mm long with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

S & F 100mm long stainless steel butt hinges, heavy duty complete all as specified and directed.

S & F extruded aluminium alloy, fabricated type handle, 150mm long

All as per item No.17 above but 100mm

M & L for preparing new wooden surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

M & L for preparing old wooden surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint.

M & L for MS work as in bands, straps, clamps, hold fast, hinges etc and similar small articles conforming to Fe.290, Gde E-165.

S & F aluminium powder coated sliding window/doors and glass window frames consisting of stranded section for frames and necessary handles, roller wheels, hinges rubber beading etc complete. Note :- Wt of aluminium shall be measured exclusive of all fittings feature hinges, handle bolts and locking arrangements

S & F aluminum alloy wire mesh 0.45 mm nominal dia of wire and avge width of aperture 1.4mm cut to size and fixed to doors/window shutters and fixed with aluminium wire stapels complete.

S & F sheet glass ordinary quality, 4mm thick and glazing with oil putty/wooden beads in squares exceeding 0.50 sqm each.

All as per item No.24 above but with pin headed/figured glass not exceeding 0.50 sqm each.

M & L for framed work as in grills, gratings and in similar work as portions of gates etc including pintle hinges, stops, sliding bolts etc conforming to Fe.290.Gde-E-165

M & L for making good jambs, forming jambs etc to openings for door and window opening including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work complete in cement mortar 1:6

Demolition of stone slab and tiles of any description or thickness in floors, aprons etc. laid dry or laid dry and pointed & removing clear off site after credit for the same is recovered by the Dept

M & L for non skid coloured ceramic tile 7 to 8mm thick (square/rectangular) area of each tile exc 0.18 sqm but no.exc 0.38 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cemrnt to match

All as per item No.29 above but as on vertical surfaces

M & L for non skid coloured ceramic tile 7 to 8mm thick (square/rectangular) area of each tile exc 0.11 sqm but no.exc 0.18 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cemrnt to match

S & F glazed ceramic tiles 300 x 200 x 7mm thick coloured on vertical surfaces such as dado skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M & L for machine cut kota stone slab for window sills 20-25mm thick, laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab including rubbing and polishing complete as in floors.

M & L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick with grey cement of pigment, set, jointed and pointed in neat cement slurry in floors

M & L for rendering 10mm thick on brick or concrete surface in CM 1:4 finished even and fair to receive glazed tiles

M & L for screed bed or bedding layer of cement mortar 1:6, 20mm thick for receive floor finish

Taking down cement plaster of any description on brick or stone walls including racking ouit joint hacking for key, scrubbing down with water etc.& removing rubbish outside MD land.

Apply one layer of concrete 20mm thick comprises composition 50 Kg cement, 3 to 6mm chips 100kg 7 sand 50 Kg mixed with spray set SL 2 to 2.5% by weight of cement and 12.5 to 16.5 ltrs of water mixed with admixture incl bonding agent & applying rust remover and guniting with pressure nozzle with a delivery capacity of 2.5 Kg/Sqm.

Rendering the entire gunniting surface with 10mm thick in cement mortar 1:4, finished the surface even & smooth without using extra cement.

Supply only welded steel wire fabric weight n.exc 4 kg/sqm

M & L for 15mm thick rendering in CM 1:6 on brick or concrete surfaces of wall , finished even and smooth without usng extra cement.

M & L for applying two coats of oil emulsion distemper over a coat of chalk whiting as preparatory to distemper including preparation of new surface or unplastered surfaces of wall with applying 3mm thick wall care putty complete all as specified and directed.

M & L for applying two coat of oil emulsion distemper over a coat of chalk whiting as preparatoy to distemper including preparation of old decorated surfaces of wall with applying 3mm thick wall care putty by complete removal of existing treatment complete all as specified and directed.

M & L for rendering 15mm thick plaster in cement mortar 1:4 on external surfaces such as stone or concrete surfaces with water proofing compound finished even and smooth without using extra cement complete all as specified and as directed. (Water proofing compound shall be measured and paid for separately)

M & L for applying two coats of damp proof weather emulsion paint over a coat of weather proof emulsion exterior primer including preparation of new surfaces of walls complete including 3mm damp proof putty all as specified and directed by Engr-in-charge.

M & L for applying two coats of damp proof weather emulsion paint over a coat of weather proof emulsion exterior primer including preparation of old surfaces of walls complete including 3mm damp proof putty all as specified and directed by Engr-in-charge.

Supply only liquid water proofing compound all as specified.

S & F in repairs UPVC pipe, 75mm bore, type B ,single socketed, in any length with rubber ring joints, fixed to walls

S & F in repair UPVC (SWR) 110 mm bore '-ditto- as above.

S & F in repairs UPVC (SWR) bends 75mm bore any radius diminishing pieces or tapers.

All as item No.50 above but 110mm bore

S & F in repairs UPVC (SWR) branch piece, single, (single Y) equal or unequal with access door, for 75mm bore pipes.

S & F in repairs UPVC (SWR) branch piece, single, (single Y) equal or unequal with access door, for 110mm bore pipes.

S & F in repairs UPVC (SWR) branch piece,double, (double Y) equal or unequal with access door, for 75mm bore pipes.

S & F in repairs UPVC (SWR) branch piece,double, (double Y) equal or unequal with access door, for 110mm bore pipes.

S & F in repairs UPVC (SWR) gully trap 125/110 mm setting and jointing with solvent cement

S & F in repairs Nahani traps CL 75mm dia with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4)

S & F in repairs PVC connection 15mm size with PTMT nuts of length 600mm.

S & F in repairs towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and plstic cleats.

M & L waste coupling 32 mm dia (PTMT) fixed in repairs for glazed ware sinks, basins etc half or full threaded with long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed for 32 mm bore.

Taking up or down steel water tubing 15mm bore and connections, including cleaning for re-fixing or removal to store

All as in item No. 62 above, but 20mm bore pipe.

S & F CPVC water tubing outer dia 20mm, SDR-11 grade with all fittings and fixed complete to walls and ceiling or laid in floors.

All as in item No. 64 above, but 25mm bore pipe.

S & F Bib tap 15mm standard of PTMT any colour high pressure, long body screwed for CPVC pipe and fixed in repair (Minimum weight 15mm-120gms) 15mm bore

S & F pillar tap 15mm of PTMT long body fancy type screwed down, screwed for CPVC pipes 15mm bore. Fixed in repair (15mm-120gm)

S & F in repairs Angle stop valve 15mm of PTMT any colour high pressure screwed for CPVC pipe and fixed in repair , (Minimum weight (15mm-90gms)

S & F in repairs Stop valve of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/ 20mm- 92gms)

S & F in repairs PVC low/high level flushing cistern, 10 Ltrs capacity including float valve, chain, PVC flush pipe.

S & F Stainless steel shower roses 100mm size, with or without swivel joint including fixing to steel pipe, fixed in repair.

Disconnecting and S & F rotational moulded polythylene water storage tank (cylindrical vertical with closed top), double layered, hoisted and fixed in position all as specified in SSR Part -I (2000Ltrs) capacity complete all as specified and directed.

Dismantling single layer Mangalore pattern or similar tiles in roofiing & removing clear off site after credit for the same is recovered by the Dept

Dismantling plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof coverings & removing clear off site after credit for the same is recovered by the Dept

Dismantling battens for tiles, shigles etc, spaced exc. 15 cm of any size including tiling fillets & removing clear off site after credit for the same is recovered by the Dept

Dismantling timber in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section & removing clear off site after credit for the same is recovered by the Dept complete all as specified and directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded in concrete brickwork and masnory portion and making good disturbed ground & removing clear off site after credit for the same is recovered by the Dept

Excavating in post holes (or similar holes) each n exc 0.5 cum in soft/loose soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surfaceall as directed

M & L for Cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) in foundations, filling and mass-concrete all as directed

S & F Pre-painted galvalume aluminium zinc coating GI based corrugate steel sheet 0.50 mm thick of an colour having Tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Ditto all as item 80 above but plain steel sheet 0.5mm thick.

M & L 5mm thick PVC plain sheet as in eaves boards fixed with and including screws and iron frame work (Note:- iron work shall be measured and paid saperately)

S & F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat section) including distance pieces, cleats etc conforming to Fe 410-W(Gde-E-250)

S & F rolled sections as in main and cross beam hips and jack, rafters, purlins where connected to common rafters and running rail and guide for sliding doors fixed with angle cleats Fe 290-W(Gde-E-165)

S & F compound girders and stanchions lattice girders aerial masts, staging for water tank and like including cap and bases , splices etc built up from two or more beam or channel section or angle with plates including all lattice bars stifferners, gusset plate. Fe 290-W(Gde-E-165)

M & L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces of any description, over 10cm in width or girth complete all as specified and directed.

Demolition wall and ceiling board or insulation board/ slabs/blankets any thickness including cover fillets & removing clear off site after credit for the same is recovered by the Dept

S & F anodized aluminium snap grid frame work for false ceiling with necessary main tee 35.00 x 23.50 x 1.50mm , cross tee and wall angle of size 23.50 x 23.50 x 1.5 mm with 605 x 605 mm grid system, conforming to IS 733, IS 737 and IS 1285 including all ceiling cleats, hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long all as specified in complete all as specified directed.

Material and labour for 6mm thick non asbestos fibre cement building boards fixed or laid/ inserted to aluminium frame work with screws complete all as specified and directed.

Dismantling of old ceiling boarding of any description, fixed in any position with screw and re-fixed in flat or sloping 6mm thick asbestos cement plain building boards fixed or laid/ inserted to timberframe or iron frame work with screws, hooks, belding, cliping etc complete all as specified and directed.

S & F in repair CPVC 32 mm dia as waste pipe fitted to basin or sink all as specified and directed inclding taking down of old pipe.

S & F in repairs vitreous china squatting pan 'Orissa' pattern, of size 580mmx440mm white with integral foot rest with and including 'P' or 'S' trap, connection to trap and to flushing pipe, trap set in and including provision of lime concrete bedding and taking out old WC and connections etc complete all as specified and as directed

Demolition of brick work or stone/boulder masonary, built in cement mortar including all quoins,arches,pillars,etc. & removing clear off site after credit for the same is recovered by the Dept complete all as specified and directed by Engineer in charge

M & L for walling laterite of squared rubble, regular coursed, well bonded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed by Engineer in charge. (Note -The rate consider is for laterite stone only as per section No.6 stone masnory para - 6.2.4 of SSR 2020)

M & L for 15mm thick plastering in CM 1:4 on external surfaces stone or concrete surfaces at any height finished even and smooth without using extra cement complete all as specified and directed.

Extra over stone walling for hammer dressing to face stone and dressing of face beds and joints, as specified, of squared rubble masonry, regular coursed, hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 20mm complete all as specifed and directed

S & F curtain rails 25 mm dia power coated aluminium with brackets stops rollers etc fixed in repairs.

S & F aluminium power coated brackets for curtain rail fixed in repair.

Taking down carefully copper/aluminium point wiring of light, fan, socket 5/15A or power point complete including fittings such as switches, ceiling rose, pendant, regulator, socket, lamp holders, brackets, lamp fittings, tube light fittings etc including switch boards and making good disturbed surfaces of wall/ceiling etc so as to match with the existing wall/ceiling/floors etc completely all as directed by Engr-in-Charge.

Taking down carefully sub main wiring including copper/aluminium/GI earth continuity conductor and making good disturbed surfaces all as directed of any sizes.

Taking down MCB DBs with MCBs of any size and capacty alongwith teadwood boards incl all fittings/furniture carefully and making good disturbed surfaces of wall

M & L for point wiring with proper colour coding complete with and including PVC insulated, unsheathed,flexible, bright annealed multi stranded copper conductor single core FRLS cables 1.5sqmm 1100 volts grade drawn through and including heavy grade rigid PVC conduit 20mm or higher dia as required at site ,totally concealed in walls /floors/ceiling and surfaces on trusse by means of saddles & clips etc including all conduit accessoriesc /fiitting/junction box/inspection covers etc of heavy grade ,ISI marked and sunk terminal boxes of factory made 16SWG pressed steel housing ,totally concealed in walls with 3mm thick industrial laminated sheet top cover ,fixed flush with wall surface by means of brass screws and sunk/cupwashers,for mounting of switches ,sockets,fan regulator etc including 1.5sqmm 1100 volts grade PVC insulated FRLS ,unsheathed flexible ,multi stranded copper conductor cable as continious earth wire connected to metallic bodies of luminiaries/fan etc at one end to common earth dolly at other end,all as specified and directed for one light point controlled by one switch.

-do- same as Item No. 102 above but For one ceiling/exhaust fan, point controlled by one switch.

-do- same as Item No. 102 above but For one 5 Amp independent socket point controlled by one switch.

-do- same as Item No. 102 above but For one 5 Amp socket point controlled by one switch on same board

-do- same as Item No. 102 above but for power point wiring with 2.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable and 2.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable as continuous earth lead.

M & L for switch,flush type, single pole, one way, 5 Amps, 240 volts, white finish complete all as specified

M & L for switch, flush type, 15 Amps, 240 Volts, single pole, white finish complete all as specified.

M & L for socket outlet, 5 pin, 5 Amps, flush type, white finish complete all as specified

S & F socket outlet, 2 in 1, 3 pin, 5/15 A, flush type, universal, 240 V white finish complete all as specified

S & F electronic socket size, rotary, 5 speed step type regulator, 120-230 V white finish complete all as specified

S&F ceiling rose, surface backlite, 65 x 20 mm three terminal

S & F lamp holder, PVC insulated body with back plate suitable for angle / batten fitting

S & F double door metallic sheet metal enclosure for DB when MCBs to be used, SPN 8 ways, 240 V with 200Amps rated bus bar complete fixed properly on in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs of cables/wires all as directed.

S & F in replacement testing and commissioning of MCB, SP, 240 volt, 6 Amp to 32 amp, 10 KA capacity having C-series connected with suitable lugs.

-do- but SPN 16-40 Amps -do-

M & L sub main wiring with two single core PVC-FRLS insulated unsheathed stranded copper conductor cable of size 4 sqmm drawn through and including heavy grade rigid PVC conduit 20mm or higher dia as required at site ,totally concealed in walls /floors/ceiling and surfaces on trusse by means of saddles & clips etc including all conduit accessoriesc /fiitting/junction box/inspection covers etc of heavy grade ,ISI marked with 4 Sqmm PVC-FR insulated unsheathed stranded copper conductor as a continuous earth wire complete all as specified. Note : (i) Two single core cable and one run of earth copper conductor/PVC conduit will be measured and paid as one unit length

M & L for earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground (earth pit not less than 2.25metre deep below natural ground level) with top edge of the plate not less than 1.5metre below normal ground level, connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel connected to main switch board/ main DB’s/ earth test point with and including necessary excavation and earth work in any type of strata, PCC 1:3:6, type C1 in chamber wall with 50mm thick, RCC cover 1:2:4, type B0 duly reinforced with 6 mm dia bar, @100mm both way with suitable lifting handle, charcoal dust and common salt mixed and packed in 150mm thick layer all around the earth plate, watering pipe of size 20mm dia medium grade, 0.63mm thick GI sheet funnel with wire mesh, GI protection pipe 15mm dia light grade up to 7.5m from electrode and engraving of earth marking on nearby structure/ building with cement motor 1:4 plate of size 200mm x 150mm x 15mm thick complete all as shown in electrical plate No. 3 of SSR Part-I complete all as specified and as directed. Note: - On testing if desired earth resistance is not obtained, the earthing will be redone at no extra cost.

M & L for cutting / boring of PCC/hard standing at a depth not more than 15 cm deep and 15 cm in breadth for passing earthing conductor and making good the disturbed surfaces with PCC (1:2:4) type B-0 or cement mortar (1:3) complete all as specified.

S & F GI pipe light grade of size 15 mm bore for laying in trenches/floors or walls including all fittings for fixing complete as required and directed by Engineer-in-Charge.

M & L for earth continuity conductor or main earthing lead 4 mm dia GI or steel wire fixed to wall on batten or recessed or buried in ground or drawn in conduit/pipe all as required at site.

S & F LED tube light fittings, Batten type 1 x 20 W, 230V ,6000K CAT No Havells LUMILINEBS20WLED865SPCWH or equivalent / Luker / crompton /Bajaj complete all as directed

S & F LED security light 20 W IP 65 all as specified and directed.

M & L for bracket made out of GI pipe 25mm dia medium grade, 0.6mtr long bent to shape with MS flat iron clamps made out of 40mmX 6mm thick FI nuts, bolts complete all as directed by Engr-in-charge incl. taking down old unsv.

M & L for cutting chases,pinning in ,making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings ,steps,cills,sunshades,shelves,lintels,etc and cutting chases for concealed water tubing or concealed conduit wiring ,etc and making good,cutting not exc 10cm girth ON BRICK WALLS.

S & F Exhaust fan 300mm sweep, metal body, single phase, 230 Volt heavy duty, with louvers, shutter including three core flexible cable of required length of size 23/0.0076 from ceiling rose/ connector to fan terminal opening the wall as required, fixing the fan with suitable size of nut, bolt washer, providing of opening on wall where required and making good the disturbed surfaces complete all as specified and directed. Make : Bajaj/Crompton Greeves/Havells

S & F MS clamps for hanging of ceiling fan with all fixing accessories to MS angle or channels,

S & F GI pipe of 15mm dia of medium grade for hanging of ceiling fans and make necessary fixing arrangement with ceilng fan and MS clamps and all as directed by Engr in Charge.

S & F LED bulb of 13/15 watt of Havells Cat Part No LHLDDEHEML8R013 OR equivalent make in Bajaj/Crompton Greaves/Philips all as specified and as directed.

Disconnecting and taking down ceiling fan of any sweep any make from any position at site, transporting to MES store Yard and rehanging/ re-fixing/ placing fan at same location at site including providing nuts, bolts, locking bolts, blade's screws, split pin, rubber real, PVC connector, washers, of suitable size etc as required and re-painting one coat of supper enameled white paint with spray painting technique complete all as directed.

S & F cord flexible 23/0.0076 including dismantling old unserviceable one as directed by engr-in-charge..

Supply and lay cable XLPE Insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 sqmm 2 core including taking down old unserviceable service wire/cable all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.50 mtr wide and not exceeding 1.50 mtr in depth for laying of cables and getting out complete all as specified and directed by Engineer-in-Charge.

Returing, filling in, including spreading, leveling watering and well ramming inlayers not exceeding 25 cms thick each layer compete all as specified and directed by Engineer-in-Charge.

Removal of surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed by Engr-in-charge.

Supply and Laying DWC HDPE pipe of outer dia of 50mm and inner dia 40mm polyethylene (PE) with smooth internal and profiled external surface for non-pressure for underground cable including bends complete all as specified and directed. Make: “Rex Polyextrusion Ltd” or equivalent as approved by GE in writing.

S & F DWC HDPE coupler of dia of 50mm complete all as specified and directed. Make: “Rex Polyextrusion Ltd” or equivalent as approved by GE in writing.

S & F galvanised pipe light grade of ISI marked 40 mm bore for passing of cable fixed to poles/walls/lay under floor complete with and including fittings as required compete all as specified and directed Engr-in-charge.

SLB Enterprises

the bhimani group of companies

Kakolil Trade Agencies

vishalconstruction

M/s S N Atiwadkar

SHUBHAM SHANKAR GAIKWAD