Repair to Roof Leakage/Seepage and Sunken portions including E/M portion at Old Mil Stn Kapurthala under GE Kapurthala.

Amount

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing servicable tiles to store and rubbish off the premises complete all as specified and as directed by Engr-in-charge.

M&L for glazed ceramic coloured tiles of approved pattern as in vertical surfaces 450x300x7mm thick set and jointed in neat cement slurry pointed in white or colour cement to match the shade of tile with 15mm thick cement screed bed (1:4) complete all as specified and as directed by Engr-in-charge.

M&L for non skid ceramic coloured tiles of approved pattern, 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18Sqm as in floor set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles with 15mm thick cement screed bed in CM (1:6) with epoxy filling in joint complete all as specified and as directed by Engr-in-charge.

Demolition of brick work/block masonry including all quoins, arches, pillars etc and clearing off the premises complete all as specified and as directed by Engr-in-Charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and as directed by Engr-in-Charge.

M&L for rendering 15mm thick on brick wall or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement including taking down cement plaster on brick or concerte surfaces including racking out joints hacking for key, scrubbing down with water etc and removing rubbish complete all as specified and as directed by Engr-in-Charge.

M&L for 15mm thick rendering in CM 1:4 on brick work or concrete surfaces with water proofing compound finished even and fair etc including taking down cement plaster on brick or concerte surfaces including racking out joints hacking for key, scrubbing down with water etc and removing rubbish complete all as specified and as directed by Engr-in-Charge. Note: WPC shall be measured and paid separately.

M&L for 10mm thick rendering in CM 1:3 on brick work or concrete surfaces finished even and smooth without using extra cement as in ceiling including taking down cement plaster on brick or concerte surfaces including racking out joints hacking for key, scrubbing down with water etc and removing rubbish complete all as specified and as directed by Engr-in-Charge.

Material and labour for TMT bars 10mm dia and over cut to length bent to shape required, including cranking, bending hooking etc & binding with and including mild steel binding wire (annealed) not less than 0.9mm dia complete all as specified and directed by Engineer-in-Charge

Taking down chowkats or frames with shutters area not exceeding 1.5sqm each (without taking off shutters from the frames) complete all as specified and as directed by Engr-in-Charge.

Taking down chowkats or frames with shutters exceeding area exceeding 1.5 sqm but not exceeding 4 sqm each (without taking off shutters from the frames) complete all as specified and as directed by Engr-in-Charge.

Taking down shutters for repairing and refixing the same in same opening of any description of area exceeding 1.0 sqm but not exceeding 2.0sqm each complete all as specified and as directed by Engr-in-Charge.

Supply and fixing solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening complete all as specified and as directed by Engr-in-Charge.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and as directed by Engr-in-Charge.

S&F pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete, as specified, including filling of hollow frame complete all as specified and as directed by Engr-in-Charge.

M&L for PCC 1:3:6 type C2 as in filling of chowkhats complete all as specified and as directed by Engr-in-Charge.

S&F factory made 2nd class, hard wood, 35mm thick glazed and skeleton shutters, open rebated and prepared to received glass, gauge, etc ( without sash bars) edges of framing plain, chambered or rounded, fitted with cut and mitred beads for securing glass, etc but divided into squares with plain chamfered or rounded mirted and rebated sash bars any numbers sizes of members of shutters complete all as specified and as directed by Engr-in-Charge.

S&F factory made 2nd class hard wood Plain, framed, panelled shutters 35 mm thick (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified and as directed by Engr-in-Charge.

S&F alumunium hinges of 100mm size for PVC door shutter complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of new wooden surface exceeding 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt in 250mm complete all as specified and as directed by Engr-in-Charge.

S&F extruded aluminium alloys handles frabicated type anodized of size 150mm long complete all as specified and as directed by Engr-in-Charge.

S&F Aluminium anodised, barrel tower bolts of extruded section and fixed, length of bolt in 200mm complete all as specified and as directed by Engr-in-Charge.

S&F extruded aluminium alloys handles frabicated type anodized of size 100mm long complete all as specified and as directed by Engr-in-Charge.

Supply and fix steel ventilators fixed type with glazing bars etc complete all as specified and as directed by Engr-in-Charge.

S&F 4.00mm thick sheet glass, ordinary quality in squares n exc 0.5 sqm each pane and glazing with oil putty complete all as specified and as directed by Engr-in-Charge.

S&F 4.00mm thick figured glass, pinhead type in squares n exc 0.5 sqm each pane and glazing with oil putty complete all as specified and as directed by Engr-in-Charge.

S&F stainless steel wire cloth 0.56mm nominal dia of wire and avarage width of aperture 1.00mm and fixed with tinned tacks/screws with bolts incl leaping wooden complete all as specified and as directed by Engr-in-Charge.

S&F steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm, 1.25 thick sheet single rebated comprises glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T-section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:2:4) type B-1 Four Nos for each window including following fitting welded to frame shutter : (a) Hold fast, 150mm long of 12mm square bar made to shape-04 Nos per window (b) Handles of z section 100mm long (c) Stopper - 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges - 01 No per leaf (e) MS Pintal hinges of size 75mm x 75mm x 12mm-02 Nos per leaf (f) Fabrication & fixing arrangement as per drg No CEJZ/TD-7/07 sheet 1/3 to 3/3. Note : Glass and painting shall be measured and paid separately under appropriate item.

S&F steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm, single rebated comprises gauzed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T-section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:3:6) type C-1 Four Nos for each window including following fitting welded to frame shutter : (a) Mild Steel Hold fast, 150mm long of 12mm square bar made to shape-04 Nos per window (b) Handles of z section 20mm x 100mm long (c) Stopper - 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges - 01 No per leaf (e) MS Pintal hinges of size 75mm x 75mm x 12mm-02 Nos per leaf (f) Grills made out of MS square bar 12mm dia welded to FI frame complete all as specified and shown on drawing No CEJZ/TD-7/07 sheet 1/3 to 3/3. Note : Wire mesh and painting shall be measured and paid separately under appropriate item.

M&L for preparation of old steel surfaces of any description over 10cm girth or width not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of new steel surfaces of any description over 10cm girth or width not otherwise described and applying two coat of synthetic enamel paint over red oxide primer complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distermper over a coat of wall care putty complete all as specified and directed by Engr-in-Charge.

Material & Labour for preparation of new plastered surfaces of walls and applying two coats of exterior emulsion paint over a coat of primer complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of whitewash on ceiling complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of old plastered surfaces of ceiling and applying two coats of whitewash complete all as specified and as directed by Engr-in-Charge.

M&L for complete removal of existing treatment on walls by applying water and scrapping of entire thickness of existing treatment with using steel scraper and thereafter applying two coat of oil bound distermper over one coat of wall care putty 2.00mm thick over a coat of appropriate primer complete all as specified and as directed by Engr-in-Charge.

M&L for complete removeal of existing treatment by applying water and scrapping of entire thickness of exsting treatment with using steel scraper and thereafter applying two coats of exterior emuslion paint over a coat of appropriate primer including 2mm thick wall care putty to achieve smooth finish complete all as specified and as directed by Engr-in-Charge. Note- Exterior emulsion paint to be done by Roller.

M&L for water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath and WC's etc as under:-

(i) Application of Two component acrylic modified cementitious coating.

(aa) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cement litance, existing coatings and achieve a gripping profile that is clean, dry and free from litance and any other form of surface contamination the installation instructions in manufacturer's published literature should be strictly compiled with, including but not limited to the following:-

(bb) Chipping out any visible cracks in ' V- Groove' pattern as applicable. Special attention on this part cleaning of cracks and then filling those cracks with SIKA latex SBR 100 putyy/ Dr Fixit 302 SBR latex/ perma latex SBR / FOSROC Nitibond SBR latex/ Asian Paints latex as required. Final cleaning of surface with power grinder, wire brush, hair brush and vaccum pressure if required.

(cc) Dampen all surfaces immediately ahead of application of Acrylic modified cemetitious coating of Sika Top seal - 107/brush Bond FOSROC/ Dr Fixit/ STP/ CICO.

(dd) While the surface is still damp from saturation (SSD), apply one coat of acrylic modified cementitious coating of Sika Top seal- 107/ Brush bond FOSROC/ Dr fixit / STP/ CICO of viscosity as per manufacturer's instructions.

(ee) Apply glass fabric sheet of Sika Fab 1 / FOSROC/ Dr Fixit/ STP while the first coat is wet.

(ff) Once touch dry apply second coat of Acrylic modified cementitious coating of Sika Top Seal- 107/ Brush bond FOSROC/ Dr FiXit/ STP/ CICO of viscosity as per manufacturer's instructions on the entire area.

(gg) Second coat shall be applied after 6-8 hrs of application of previous coat and in the direction right angle to the previous coat.

(hh) The waterproofing coating should be taken to a height minimum 300mm above the finished floor level on the vertical surface.

(jj) It is essential to cure acrylic modified cementitious coating immediately after application (minimum 6-8 hrs drying) for a minimum of 3 to 54 days to ensure full cement hydration and to minimize cracking.

(kk) A protection plaster (12-15mm thick) in CM 1:3 admixed with appropriate integral water proofing compound has to be applied on the walls.

Providing and applying a protection screed of 50mm thick 1:4 cement sand mortar admixed with Sika Plastocrete over the applied water proofing coating on horizontal surfaces.

Admixture : - Sika Plastocrete plus/ FPSROC/ Dr Fixit / STP/ CICO confirming to IS 2645.

(ll) All the corners and joints should be pretreated with elastic waterproofing sealing tape with a woven bonding mesh on each surface and an elastic expansions zone in the centre of make Sika Seal Tape S/FOSROC/Dr Fixit/STP.

(mm) The membrane has to be protected in accordance with the manufacturer's recommendations until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturer's. recommendations.

(nn) Waterproofing treatment has to be carried out through applicators authorised.

(ii) All the joints of pipe sand traps within sunken portion shall be selaed properly by Epoxy sealant.

(iii) All CI traps in sunken slabs to be enclosed with PCC 1:1.5:3 (min 15cm) all - round.

(iv) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40 mm stone aggregate) complete all as specified and as directed by Engr-in-Charge.

(v) Providing drainage spout pipe PVC 40mm dia bore light grade upto outside of outer wall (Approx 450mm to 600 mm long) including cutting to existing wall and making good the disturbed surface complete all as specified and as directed by Engr-in-Charge.

(vi) Providing 75mm thick cement concrete 1:2:4 type B-0 using 12.5 mm grade stone aggregate as in flooring for laying floor finish complete all as specified and as directed by Engr-in-Charge. Note :- Item No 38.19, 38.20 & 38.30 shall be measured and paid seprately.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed by Engr-in-Charge.

M&L for providing PVC pipe as spout pipe heavy class of dia 40mm complete all as specified and as directed by Engr-in-Charge.

S&F 40 mm PVC (SWR) bend complete all as specified and as directed by Engr-in-Charge.

M&L for PCC (1:5:10) type E2 using 40mm graded crushed stone aggregates as in mass concreting, filling, sub base complete all as specified and as directed by Engr-in-Charge.

M&L for PCC type B-0 (1:2:4) (12.5mm stone graded aggregate), 40 mm thick for receiving top finishing layer of ceramic tiles for sunken portion finished even and rough etc complete all as specified and as directed by Engr-in-Charge.

Taking down GI tubing & connection 15mm dia laid in floor / trenches or fixed to walls complete all as specified and as directed by Engr-in-Charge.

S&F tubing 15mm dia high density polyethylene (HDPE) pipes of pressure rating 6 kgf/sq. cm fixed to walls & ceiling or laid in floors complete all as specified and as directed by Engr-in-Charge.

Taking down GI tubing & connection 20mm dia laid in floor / trenches or fixed to walls complete all as specified and as directed by Engr-in-Charge.

S&F tubing 20mm dia high density polyethylene (HDPE) pipes of pressure rating 6 kgf/sq. cm fixed to walls & ceiling or laid in floors complete all as specified and as directed by Engr-in-Charge.

S&F in repairs 15mm bore CP bib taps fancy type cast copper alloy with crutch or butter fly handle screwed down for iron pipe or for brass ferrule and fixed complete all as specified and as directed by Engr-in-Charge.

S&F in repairs 15mm dia stop/angle valve, CP cast copper alloy with crutch or butterfly handle. Screwed down high pressure, screwed both ends for iron pipe and fixed complete all as specified and as directed by Engr-in-Charge.

Supply and fix in repairs for vitreous china ware wash basin white, flat back size 550 X 400mm including 15mm dia pillar tap chromium plated, CP waste coupling, waste fittings, union and waste pipe 32mm dia of required length and all necessary inlet, out let connections complete all as specified and as directed by Engr-in-Charge.

Supply and fix in repairs vitreous china squatting pan Orissa pattern wash down water closet of size 580x440mm, white, with integral foot rests complete with P or S trap, PVC flushing cistern low level of 10 ltrs capacity including brackets for flush tank, PVC flush pipe and all necessary fittings etc complete all as specified and as directed by Engr-in-Charge.

S&F in repairs PVC (SWR) floor trap with grating and diameter of outlet 75mm including jointing to waste pipe fixed with solvent cement complete all as specified and as directed by Engr-in-Charge.

S&F in repairs 15mm dia fancy type chromium plated stop valves with long shank and cup (concealed type) cast copper alloy screweddown high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed by Engr-in-Charge.

S&F in repairs shower rose 100mm with cp arm of chromium plated any colour or fixing with 15mm pipe (minimum weight 40gm) complete all as specified and as directed by Engr-in-Charge.

Cutting chases pinning in brick/stone/blocks masonary in making good to facings where required and pointing in CM (1:3) to ends or eges of steps, cills, sun shades, shelves, lintel etc and cutting chases for concealed water tubing or etc and making good complete all as specified and as directed by Engr-in-Charge.

S&F 75 mm PVC (SWR) pipes in repair single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by Engr-in-Charge.

S&F 75 mm PVC (SWR) pipes in repair single socketed in any length laid in floor complete all as specified and as directed by Engr-in-Charge.

S&F 75 mm PVC (SWR) bend complete all as specified and as directed by Engr-in-Charge.

S&F 75 PVC (SWR) junction single, (single T) equal or unequal complete all as specified and as directed by Engr-in-Charge.

S&F 75 PVC (SWR) junction double, (double T) equal or unequal complete all as specified and as directed by Engr-in-Charge.

S&F 110 mm PVC (SWR) pipes in repair single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by Engr-in-Charge.

S&F 110 mm PVC (SWR) bend complete all as specified and as directed by Engr-in-Charge.

S&F 110 PVC (SWR) junction single,(single T) equal or unequal complete all as specified and as directed by Engr-in-Charge.

S&F 110 PVC (SWR) junction double, (double T) equal or unequal complete all as specified and as directed by Engr-in-Charge.

S&F 75mm PVC(SWR) vent cowl complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in repair 500 Ltrs capacity rotational moulded polythelene water storage tanks triple layer (cylindrical vertical with closed top) hoisted and fixed in position as per SSR Part-1 including fittings & 20mm dia brass ball valve complete all as specified and directed by Engineer-in-Charge.

S & F 40mm dia GI pipe heavy grade for overflow of water tanks including necessary bends and connection with water tank complete all as specified and as directed by Engr-in-Charge.

S&F in repair 20mm gunmetal globe and gate valve with iron welded hand secrewed both and for iron pipe complete all as specified and as directed by Engr-in-Charge.

S&F in repair 15mm gunmetal globe and gate valve with iron welded hand secrewed both and for iron pipe complete all as specified and as directed by Engr-in-Charge.

S& F in repairs Ball valves 20mm high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed Minimum weight 25mm-455gms complete all as specified and as directed by Engr-in-Charge.

Dismantling of brick tiles or terracing tiles laid bedded and pointed in cement mortar in single layer on roofs complete all as specified and as directed by Engr-in-Charge.

Demolition of mud in roof any thickness including plastering & leeping removed complete all as specified and as directed by Engr-in-Charge.

M&L for rendering 10mm thick cement mortar 1:3 on concrete surface finished the surfaces even and fair with waterproofing compound complete all as specified and as directed by Engr-in-Charge. Note :- WPC to be measured and paid seprately.

Supply only integral water proofing compound complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of newly plastered surface making surface completely dry and applying a coat of bitumen primer @ 0.40 ltr/sqm and after drying of primer apply APP modified water proofing membrane with non woven polyster reinforcement 3mm thick superior multipolymeric weighing not less than 3kg/sqm with properties of high penetration and centre core consisting of 90 micron high molecular high density polyethylene (MHHDPE) film consisting of five layers with a coat of hot blown bitumen 85/25 @ 1.20 kg/sqm under and over the APP membrane laid with torching application to the surface complete and sealing the side as well as end laps (overlaps should not be less than 10 cm) complete all as specified and as directed by Engr-in-Charge.

M&L for 40mm thick brick tiles laid on 15mm screed bed in cement mortar 1:3 with jointing and pointing in cement mortar (1:3) mixed with 5% crude oil by weight of cement complete all as specified and as directed by Engr-in-Charge.

All as per item no 77 above but except brick tiles complete all as specified and as directed by Engr-in-Charge.

Material and labour for 40 mm thick Cement concrete type B1, 1:2:4 (using 20 mm graded stone aggregate) as in PCC padding over roof slab complete all as specified and as directed by Engr-in-Charge.

M&L for cement concrete Type B0 1:2:4 (12.5mm graded stone aggregates) as in roof kerbs, rounded or chamfered edges complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of affected concrete and steel surface as in ceiling of roof slab, beams by cleaning with metallic wire brush scrupiously and carrying out the following operations stepwise: (i) Applying rust remover solution on steel bars by using cotton waste swab or by brush and leave the surface for 15-30 minutes. Remove the loose rust particles by srcubbing with brush and wash the steel surface with water. (ii) Apply red oxide primer over cleaned steel surfaces. (iii) Apply epoxy bonding agent (adherent solution) over cleaned dust freed old concrete surface. (iv) Apply polymer mortar with the help of trowel in single or multilayer as an when required during application and finishing the surface even and smooth. Note:- (a) The bars which are corroded badly need to be strengthen by placing new bars by means of welding with proper splice length and will be measured and paid seprately under appropriate item. (ii) The rate of item includes necessary formwork,shuttering, scaffholding, staging etc all as specified .

Taking down aluminium point wiring for light, fan, bell socket, power socket etc complete including fittings and fixtures removing from site and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed by Engr-in-Charge.

Material and labour for point wiring complete with 1.5 Sqmm single core multistranded copper conductor PVC (FRLS) insulated cable in PVC concealed conduit of size 19/20 mm (ISI Marked) including PVC accessories (concealed in wall and surface in ceiling complete including cutting chasing & making good to disturbed surface etc including pressed steel terminal boxes (sunk in wall) with 3 mm thick plastic laminated sheet top cover with 1.5 Sqmm insulated un-sheathed PVC insulated copper conductor common earth and connecting to earth dolly for :-

(a) One light point controlled by one, one way switch complete all as specified and as directed by Engr-in-Charge.

(b) One fan point controlled by one, one way switch complete all as specified and as directed by Engr-in-Charge.

(c) One socket outlet 3 Pin, 5 Amp on independent board complete all as specified and as directed by Engr-in-Charge.

(d) One socket outlet 3 Pin, 5 Amp on same board complete all as specified and as directed by Engr-in-Charge.

M&L for point wiring with 4.00 Sqmm single core multi-stranded copper conductor PVC (FRLS) insulated, unsheathed cable 1100 volt grade in PVC concealed conduit of size 19/20 mm (ISI Marked) including PVC accessories (concealed in wall and surface in ceiling complete including cutting chasing & making good to disturbed surface etc including pressed steel terminal boxes (sunk in wall) with 3 mm thick plastic laminated sheet top cover with 1.50 Sq mm single core, multi-stranded copper conductor, PVC insulated, unsheathed cable for common earth and connecting for earth dolly for 5 pin, 15 Amp socket outlet on Independent board.

S&F switch piano flush type single pole one way 5 Amp (ISI Marked) complete all as specified and as directed by Engr-in-Charge.

S&F switch piano flush type single pole one way 15 Amp (ISI Marked) complete all as specified and as directed by Engr-in-Charge.

S&F socket out let 2 in 1, 3 pin 5 Amp flush type (ISI Marked) complete all as specified and as directed by Engr-in-Charge.

S&F socket out let 2 in 1, 3 pin 15 Amp flush type (ISI Marked) complete all as specified and as directed by Engr-in-Charge.

M&L for ceiling rose, surface Bakelite 65 x 17.50 mm of three terminals PVC / Polycarbonate, isolated body (ISI Marked) complete all as specified and as directed by Engr-in-Charge.

Taking down old unserviceable flourescent tube light fitting 36/40 watt fluorescent tube light fittings direct to walls or roof as ordered and disconnecting electrically with the electrical system and all materials required for the same. The rates also include making good the same to match with the existing surface complete all as specified and as directed by Engr-in-Charge.

Supply, installation, testing and commissioning Supply and fixing LED lights fitting 1 x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed complete all as specified and as directed by Engr-in-Charge.

Taking down old unserviceable lamp holder and S&F lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings including LED lamp 09 Watt complete all as specified and as directed by Engr-in-Charge.

M/S Satguru enterprises (BID ID -3310081)

JOGRAJ CONSTRUCTION COMPANY (BID ID -3319511)

somyaenterprises (BID ID -3314405)

COSMO BUILDERS (BID ID -3320775)

Akarsha Enterprises (BID ID -3314378)

BEHL CONSTRUCTION CO (BID ID -3314517)