PROVN OF CERTAIN SENCTION LBW AND SPECIAL REPAIR WORK IN THE AREA OF AGE B/R-II UNDER GE SGNR AT MILITARY STATION SRI GANGANAGAR

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed by Engineer - in - Charge

Returning filling in, including spreading levelling, watering and well ramming in layers not exc. 25 cms thick in soft/ loose soil complete all as specified and directed by Engineer - in - Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25 cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Surface dressing n. exc. 15 cm deep in soft/loose soil complete all as specified and directed by Engineer-in-Charge .

M & L for sand filling (25 mm thick) under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer - in - Charge.

Removing excavated material n. exc. 50 m & depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed by Engineer - in - Charge.

M&L for hard core of gauge n. exc 63 mm, deposited spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surface using broken bricks complete all as specified and directed by Engineer - in - Charge.

M&L for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed by Engineer - in - Charge.

M&L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed by Engineer - in - Charge.

M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed by Engineer - in - Charge.

M&L for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed by Engineer - in - Charge.

M&L for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed by Engineer - in - Charge.

M&L for reinfocement cement concrete 1: 2:4 Type B-1 (20mm graded stone aggregate)as in in RCC manholes cover chajja, kitchen slab etc complete all as specified and directed by Engineer - in - Charge

M&L for PCC (1:4:8) type D-2, (40 mm graded stone aggregate) as in foundation complete all as specified and directed by Engineer - in - Charge

M&L for PCC (1:3:6) type C-2, (40 mm graded stone aggregate) as in foundation of posts and struts complete all as specified and directed by Engineer - in - Charge

M&L PCC 1:2:4 type C-0 (12.5 mm graded aggregate) for filling of pressed steel frame and hold fast etc. complete all as specified and directed by Engr-in-charge.

M & L for PCC 1:2:4 Type B –1 (20mm graded stone aggregate) for kerb stone and similar works with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in CM 1:4 with joints to match complete all as specified and directed by Engineer - in - Charge.

M&L for reinfocement cement concrete 1: 2:4 Type B-1 (20mm graded stone aggregate)as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer - in - Charge

M&L for reinfocement cement concrete 1: 2:4 Type B-1 (Design mix M-25 ) (20mm graded stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed by Engineer - in - Charge

M&L for reinfocement cement concrete 1: 2:4 Type B-1 (Design mix M-25 ) (20mm graded stone aggregate) as in chajjas complete all as specified and directed by Engineer - in - Charge

M&L for reinfocement cement concrete 1: 2:4 Type B-1 (Design mix M-25 ) (20mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer - in - Charge

M&L for reinfocement cement concrete 1: 2:4 Type B-1 (Design mix M-25 ) (20mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engineer - in - Charge

M&L for reinfocement cement concrete 1: 2:4 Type B-1 (Design mix M-25 ) (20mm graded stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and directed by Engineer - in - Charge

Cutting holes into or through cement concrete slabs, chajjas, etc. reinforced or otherwise exc 250 sqm but n exc 500 sqm complete all as specified and directed by Engineer - in - Charge

M & L brick work with sub class 'B' bricks straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 but except bricks complete all as specified and directed by Engineer - in - Charge.

M & L brick work with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed by Engineer - in - Charge.

M&L 20mm thick Granite (of any type) (table rubbed and polished) work in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) including Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engr-in-charge.

M&L 15mm thick Granite (of any type) (table rubbed and polished) work in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) including Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes in CM 1:6 including making hole in granite slab for gas pipe complete all as specified and directed by Engr-in-charge.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed by Engineer - in - Charge

M&L for form work to sides & soffits of suspended slab such as roof slabs, floor slabs, landings and similar work; n. exc. 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete complete all as specified and directed by Engineer - in - Charge

M&L for Formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finished surfaces of finished concrete complete all as specified and directed by Engineer - in - Charge

M&L for formwork to to sides of pillars, posts, struts, piers, columns and stanchions including for edges rough finished surfaces of concrete complete all as specified and directed by Engineer - in - Charge

S & F 2nd class clean sawn hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engineer - in - Charge.

S & F Second class hard wood factory made wire glazed and skeleton window shutters, 35mm thick, open rebated and prepared to receive glass, gauze, etc divided into squares with plain, chamfered or rounded mitred and rebated sash bars any number & fitted with cut and mitred beads for securing gauze/wire cloth, etc sizes of members of shutters as specified in SSR Part-I, section 8 clause 8.24 (a) complete all as specified and directed by Engineer - in - Charge.

S & F 35mm thick,Second class hard wood factory made Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed by Engineer - in - Charge.

S & F 35mm thick,Second class hard wood factory made Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer - in - Charge.

Taking down chowkats or frames (without taking off shutters from the frame) n. exc.1.5 sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down steel window or ventilator fixed type with glazing bar complete all as specified and directed by Engineer - in - Charge.

S & F alluminium anodised barrel tower bolts 125mm long extruded section complete all as specified and directed by Engineer - in - Charge.

S & F alluminium anodised barrel tower bolts 150mm long extruded section complete all as specified and directed by Engineer - in - Charge.

S&F 300mm mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed. complete all as specified and directed by Engineer - in - Charge.

S & F butt hinges, medium weight, cold rolled mild steel, and fixed of size 100mm fixing properly with screws etc complete all as specified and directed by Engineer - in - Charge.

S&F Continuous( piano) hinges , mild steel , bright finish or electrogalvanised Width of flaps 30mm (when open) complete all as specified and directed by Engineer - in - Charge

S & F 150 mm Mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed by Engineer - in - Charge

S & F 150 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engineer - in - Charge

S&F mortice lock with four lever (vertical type) with brass body 75 mm long complete all as specified and directed by Engineer-in-charge.

S&F Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and directed by Engineer - in - Charge.

S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engr-in-charge.

S & F stainless steel tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge.

S&F floor door stopper of aluminum alloy body and (over all length of cover plate 150 mm) tongue anodised with hard drawn steel spring fixed in door complete all as specified and directed by Engineer-in-chrage.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer - in - Charge.

S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed by Engr-in-charge.

S&F mild steel work i.e. angle iron/ flat iron as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engineer-in-charge.

S&F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed by Engineer - in - Charge.

S&F mild steel falt iron 25x6 mm as in hold fastcon forming to Fe.290.Gde-E-165 complete all as specified and directed by Engineer - in - Charge.

S&F 10 mm dia MS round bar for fixing of chain link fencing with post complete all as specifies and directedby Engineer - in - Charge.

Supply only chain link fencing galvanised mild steel hot dipped(IS -2721) of 4 mm dia of mesh size 100x100 mm complete all as specified and directed by Engineer - in - Charge. Note:- The weight of chain link fencing shall be ascertained by BOO as directed by GE and payment shall be paid accordingly BOO duly countersigned by GE shall be encloused with final bill.

Fixing only of chain link fencing including line wires, any mesh size and type to any type of satanderds, rails, straining bolts etc including binding wire complete all as specifed and directed by engineer-in-charge.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long and dia of neck 12 mm complete all as specified and directed by Engineer - in - Charge.

M&L for TMT bars 8 to 10 mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia using TMT bars complete all as specified and directed by Engineer - in - Charge.

M & L for mild steel TMT bars 5mm dia and over upto and including 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia as in stirrups, spacers and binders complete all as specified and directed by Engineer - in - Charge.

M&L for pressed steel frame for doors of size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed by Engineer - in - Charge.

M&L for Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete with Powder Coating on aluminium minimum thickness of powder coating 50 micron all as specification the top and bottom horizontal members and vertical members adjacent walls and cills where required and fixing with the help of rawl plug and screw or with fixing clip or with expansion hold plate fasteners. Aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required complete all as specified and directed by Engineer - in - Charge.

M&L for Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc complete all as specified and directed by Engineer - in - Charge.

S&F powder coated aluminium windows and ventilator shutters, side hung type without sash bars, aluminium saction weighing 0.55 kg/M including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fitting such as aluminium peg stay 150mm long (1No), powder coated aluminium hinges type B-21 100 mm long (2No), suitable powder coated aluminium handle -(1No), and powder coated aluminium self closing tower bolt 75mm long (1No) complete all as specified and directed by Engineer - in - Charge.

S&F in repair , Prelaminated particle board,19 mm thick interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed by Engineer - in - Charge.

M & L for 18- 20 mm thick machine cut kota stone slab flooring laid over and including 15 mm thick screed bed in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed by Engineer - in - Charge.

M & L for 18-20 mm thick machine cut kota stone slab as in vertical surfces such as skirting, dados etc, laid over and including 10 mm thick backing coat in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed by Engineer - in - Charge.

M & L for 75 mm thick cement concrete 1:3:6 type C –2 (40mm graded stone aggregate) as in plinth protection or similar works finished even and smooth with using extra cement etc complete all as specified and directed by Engineer - in - Charge.

M&L for 100mm thick cement concrete (1:4:8) type D-2, (40 mm graded stone aggregate) as in sub base, foundation filling and mass concrete complete all as specified and directed by Engineer - in - Charge

M&L for 100 mm thick cement concrete 1:2:4, Type B-1 (40mm graded aggregate) as in floor finished even and fair complete all as specified and directed by Engineer - in - Charge.

M&L for 25 mm thick cement concrete 1:2:4, Type B-1 (20mm graded aggregate) as in floor finished even and fair complete all as specified and directed by Engineer - in - Charge.

M&L for precast coloured rubber moulded concrete machine pressed concrete interlocking paver blocks any shape and size conforming to IS 15658-2006 of 60 mm thickness, M 35 grade wirh grey cement and pigment complete all as specified and directed by Engineer-in-Charge.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.36 sqm in floor etc, laid over and including 15 mm thick screed bed in CM 1:4 and set and jointed in cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

M&L for glazed ceramic coloured tiles interior grade, of size 300x450x8mm thick as on vertical surfaces like dados or skirting laid over and including 10mm thick rendering in CM 1:4 and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises,complete all as specified and directed by Engineer-in-charge.

Taking down cement plaster on brick or concreate wall surfaces including racking out joints, hacking for key, scrubbing down with water etc. complete complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick in CM 1:4 on brick work or concrete work surfaces including finished even & smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

M&L 15 mm thick rendering in CM 1:6 on face of brick / concrete wall surfaces including finished even & smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

M&L 5 mm thick rendering in CM 1:3 on ceiling surfces including finished even & smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement based paint over a coat of white wash complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of new plaster surfaces of walls and applying three coat of white wash complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new plaster surfaces of ceiling and applying three coat of white wash complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of oil emulsion distemper, over a coat of chalk whiting complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of ceilings and applying two coats of oil emulsion distemper, over a coat of chalk whiting complete all as specified and directed by Engineer-in-Charge.

S & F 4mm thick figured glass, pin head type and glazing with oil putty or fixed with beads in suqares n.exc 0.5 Sqm in each pane complete all as specified and directed by Engineer - in - Charge

M&L for preparation of new wood and wood based surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of Pink primer complete all as specified and directed by Engineer - in - Charge.

M&L for preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide, zinc chrome primer complete all as specified and directed by Engineer - in - Charge

S & F Galvanised steel water tubing 25 mm bore medium grade with all fittings concealed including cutting chases to brick wall/ceiling or laying in floors and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

S & F Galvanised steel water tubing 15 mm bore medium grade with all fittings concealed including cutting chases to brick wall/ceiling or laying in floors and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

S & F Galvanised steel water tubing 20 mm bore medium grade with all fittings concealed including cutting chases to brick wall/ceiling or laying in floors and making good disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

Taking down 15 mm bore Galvanised steel water tubing with all fittings complete all as specified and directed by Engineer-in-Charge.

Taking down 20 mm bore Galvanised steel water tubing with all fittings complete all as specified and directed by Engineer-in-Charge.

Taking down 25 mm bore Galvanised steel water tubing with all fittings complete all as specified and directed by Engineer-in-Charge.

Dismantling and taking down water tank of capacity exc. 250 Litre but n. exc. 500 litre capacity complete all as specified and directed by Engineer - in - Charge.

Dismantling and taking down water tank of capacity exc. 500 Litre but n. exc. 1000 litre capacity complete all as specified and directed by Engineer - in - Charge.

S&F rotational moulded white colour polyethylene water storage tank 500 litre capacity (Cylindrical vertical with closed top) hoisted and fixed in position with necessary fittings complete all as specified and directed by Engineer - in - Charge. (Note : PVC tanks shall be ISI marked, having two layres )

S&F rotational moulded white colour polyethylene water storage tank 1000 litre capacity (Cylindrical vertical with closed top) hoisted and fixed in position with necessary fittings complete all as specified and directed by Engineer - in - Charge. (Note : PVC tanks shall be ISI marked, having two layres )

S & F in repairs, 15mm bib tap cast copper alloy,fancy type, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferule complete all as specified and directed by Engineer-in-Charge. Make: Prayag cat part no-8306 Parryware cat part no- T3504A1, Cera cat part no- HTF3001151 or equivalent cat part as approved by GE

S&F in repairs, 15mm bore stop cock / valve cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repair 20mm bore stop cock / valve cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repair 25mm bore stop cock / valve cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed by Engineer - in - Charge.

S&F Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm- 45gms/40mm-60 gms) for sinks and basins complete all as specified and directed by Engineer - in - Charge

S&F grating doom 100 mm dia of PTMT complete all as specified and directed by Engineer-in-Charge. Note:- Minimum weight 25gms

S&F 100mm dia bore sand cast, cast iron soil, waste and vent pipes in any length with or without ears with cement joints laid in trenches or fixed to wall complete all as specified and directed by Engineer - in - Charge

S&F 100mm bore cast iron Bends (any radius),with duck's foot or heel rest diminishing pieces or tapers (larger bore measured) complete all as specified and directed by Engineer-in-Charge.

S&F PVC connections 15mm size with PTMT nut of length 600mm complete all as specified and directed by Engineer-in-Charge. Make:- Prayag cat part No- BS-115(long) or equivalent cat part as approved by GE

M & L for PCC 1:3:6 type C –2 bed to drain pipes 150 mm including packing under, haunching against the sides of pipes after they are laid and tested complete all as specified and directed by Engineer - in - Charge.

M&L for Salt - glazed stone ware drain pipes 150mm bore laid in trenches and jointed complete all as specified and directed by Engineer - in - Charge

M&L for reinfocement concrete pipes, class NP2, 200 mm dia laid and jointed complete with collars complete all as specified and directed by Engineer - in - Charge

M&L for Salt glazed stoneware gully traps, square or round mouthed , type 'P'Size of guly traps in mm150x100 complete all as specified and directed by Engineer - in - Charge

S&F sinks with drainage board made of stainless steel 1 mm thick for kitchen with plugs, washers and waste coupling 40mm bore dia of discharge pipe , waste pipe plain 90cm long suitable for sink waste coupling, waste jali including making grooves , fixing properly or bedding in cement mortar to walll or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer - in - Charge.

S&F in repair water closet vitreous china squatting pan "Orrisa pattern" size 580mmx440mm white with integral foot rests and CI 'P' trap and proper connecting to flushing cistern complete all as specified and directed by Engineer-in-charge.

S&F 10 litre capacity low level PVC valve less, syphonic action type flushing cistern, white, with inlet, ball valve, float and handle including bracket and provision of flush pipe of polythene of high density or PVC, 32mm dia complete all as specified and directed by Engineer-in-Charge.

Demoliton of brick work built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed by Engineer - in - Charge.

Dismatling stone slabs and tiles of any description or thickness in floors, aprons laid, bedded and pointed in any mortor, including cement mortar bedding and removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer - in - Charge

Demolition of ctimber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed by Engineer - in - Charge

Demolition and breaking up drain pipes of cast iron 100mm bore or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches complete all as specified and directed by Engineer - in - Charge

S & F Fiber Glass Reinforced plastic (FRP) Door Frames of required colour of three legged of cross section 90mmx45mm having single rebate of 32mmx45mm having single rebate of 32mmx15mm to receive shutter of 30 mm thickness. The laminate door frame molded with fire retardant grade unsaturate polysterresinn and chopped mat.Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiberglass from all sides, MS stay shall be provided at the bottom to steady the frame complete all as specified and directed by Engineer - in - Charge

S & F 30mm thick glass fiber reinforced plastic (FRP) paneled door shutter of required colour and approved brand and manufacture made with fire retardent grade unsaturated polyster resin moulded to 3mm thick FRP laminated for forming hollow rails and style with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings cast monolithically with 5mm thick FRP laminate for panels for conforming to IS:14856-2000 complete all as specified and directed by Engineer - in - Charge.

S&F stainless steel plate rack 900x775x250 mm thickness of sheet 1 mm thick complete all as specified and directed by Engineer - in - Charge. Make:- Anupam International cat part No KPR-311 or equivalent approved by GE

S&F wall hung WC with UF Seat Cover ,Hinges, Accessories Set Size 385 x 595 x385 white complete, including concealed body flushing cistern with hinging arrangement, complete all as specified and directed by Engineer-in-Charge

S&F vitreous China urinals,with Fixing Accessories set Size 375 x 315 x 620 complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (including fixing supply pipe to flushing cistern, trap and waste pipe) and including Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. complete all as specified and directed by Engineer - in - Charge.

S&F vitreous china wash hand basin counter shank Size 610 x 475 x 210 mm with green/black granite slab to be cut and polished at site as per requirement and approved by Engineer-in-charge, including brackets, 32mm bore brass chromium plated waste coupling & 32mm bore low density polythelene (LDPE) flush pipe of pressure 6Kgf/Sqcm (1.00M long,) including 15mm bore 450/600mm length PVC connection with PTMT nuts complete all as specified and directed by Engineer-in-Charge. (Note : Granite and slab shall be measured and paid seperately).

S&F soap dish CP brass 100mm dia (round or oval) fixed to walls or dados. complete all as specified and directed by Engineer - in - Charge.

S&F Toilet Roll Holder with Flap CP brass complete all as specified and directed by Engineer - in - Charge.

S&F frameless rectangular 1500mm x600 mm 5 mm thick glass mirror with double coat for protection and longevity grounded edges for safety and silver plating on the back for better reflection. mounted on wall with necessory fiments complete all as spesified and directed by Engineer-in -charge.

S&F frameless rectangular LED Mirror with touch switch 600mm x800 mm 5 mm thick glass mirror with double coat for protection and longevity grounded edges for safety and silver plating on the back for better reflection. mounted on wall with necessory fiments complete all as spesified and directed by Engineer-in -charge.

S&F frameless rectangular 800mm x 600 mm 5 mm thick glass mirror with 5 mm coloured glass shelf with stainless rails and double coat for protection and longevity grounded edges for safety and silver plating on the back for better reflection. mounted on wall with necessory fiments complete all as spesified and directed by Engineer-in -charge.

S&F Corner glass shelf with bracket and 5 mm thick glass shelf with stainless rails complete all as spesified and directed by Engineer-in -charge.

S&F venitian window blinds with closing and opening arrengement complete all as spesified and directed by Engineer-in -charge.

S&F chromium plated tubular towel Rack 600mm long with lower hanger complete all as specified and directed by Engineer - in - Charge.

S&F chromium plated tubular towel Ring Square complete all as specified and directed by Engineer - in - Charge

S&F Single lever Basin Mixer without Popup waste with 450 long Braided Hoses with long screwed for iron pipe of 15 mm dia, complete all as specified and directed by Engineer - in - Charge.

S&F Central Hole Basin Mixer without Popup waste System with 450 mm long Braided House with long screwed for iron pipe of 15 mm dia complete all as specified and directed by Engineer - in - Charge.

S&F aquisense Sensor Faucet for Wash Basin With Base Flange fixed for iron pipe of 15 mm dia complete all as specified and directed by Engineer - in - Charge.

S&F angle stop cock with wall flange fency type cast copper alloy 15 mm bore iron pipe or for union and complete complete all as specified and directed by Engineer - in - Charge.

S&F Concealed stop cock with wall flange fency type cast copper alloy 15 mm bore iron pipe or for union complete all as specified and directed by Engineer - in - Charge.

S&F health faucet ABS body with wall hook and 1 metre SS braided rubber hose pipe fency type complete all as specified and directed by Engineer - in - Charge.

S&F Jet spre CP body with 1 metre SS braided rubber hose pipe fency type complete all as specified and directed by Engineer - in - Charge

S&F 15mm bib cock with wall flange fency type and aerator cast copper alloy, chromium plated fency type screwed for Iron pipe complete all as specified and directed by Engineer - in - Charge.

Taking down copper/aluminium point wiring (light,fan,socket or power)complete including fixture and fittings such as switches& sockets and removing materials for taking credit complete all as specified and directed by Engineer-in-charge.

M&L for concealed conduit point wiring complete for light /fan with cable 1.5 sqmm(Nominal area) FRLS PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC conduit pipe medium grade 20mm bore,pipe hooks,elbows,junction covers and junction boxes, after cutting in wall chasing for conduits and sinking's for sunken cast iron /pressed steel terminal boxes of suitable length and thickness for mounting switches, sockets, fan regulator with 3mm thick plastic laminated seat cover fixed with brass screws and cup washers, duly grouting and painted with red oxide metal primer and making good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth contuity conductor along with point wiring of 1.5 sqmm copper FRLS PVC insulated cable for one light/fan point controlled by one way switch and connected to common earth dolly, complete all as specified and directed by Engr-in-charge.

All as described in Srl item No -145 here in before but for one switch socket combination 5/6 Amps on independent board complete all as specified and directed by Engineer - in - Charge.

All as described in Srl item No -145 here in before but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in - Charge.

All as described in Srl item No. 145 here in before but for one switch socket combination 6 pin 5/15 Amps on independent board with 2.5 Sqmm (Nominal Area) FRLS PVC insulated multistranded unsheathed copper conductor and continuous earth contuity conductor along with point wiring of 2.5 sqmm copper FRLS PVC insulated copper cable complete all as specified and directed by Engineer - in - Charge.

M&L for concealed conduit point wiring complete for light /fan with cable 1.5 sqmm(Nominal area) FRLS PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC conduit pipe medium grade 20mm bore,pipe hooks,elbows,junction covers and junction boxes, after cutting in wall chasing for conduits and sinking's for modular metal flush boxes suitable length and thickness for mounting switches, sockets, fan regulator with modular cover plate with 3mm thick plastic laminated seat cover fixed with brass screws and cup washers, duly grouting and painted with red oxide metal primer and making good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth contuity conductor along with point wiring of 1.5 sqmm copper FRLS PVC insulated cable for one light/fan point controlled by one way switch and connected to common earth dolly, complete all as specified and directed by Engr-in-charge.

All as described in Srl item No -145 here in before but for one modular switch socket combination 5/6 Amps on independent board complete all as specified and directed by Engineer - in - Charge.

All as described in Srl item No -145 here in before but for one three pin modular socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in - Charge.

All as described in Srl item No. 145 here in before but for one modular switch socket combination 6 pin 5/15 Amps on independent board with 2.5 Sqmm (Nominal Area) FRLS PVC insulated multistranded unsheathed copper conductor and continuous earth contuity conductor along with point wiring of 2.5 sqmm copper FRLS PVC insulated copper cable complete all as specified and directed by Engineer - in - Charge.

S & F modular switch 5/6 Amp single pole one way one module complete all as specified and directed by Engineer - in - Charge

S & F modular switch socket combination 5 pin, 5/6 Amps 5 in 1 flush type complete all as specified and directed by Engineer - in - Charge

S & F modular switch socket combination 6 pin 5/16 Amps flush type complete all as specified and directed by Engineer - in - Charge.

S & F modular Socket outlet 5 pin 5 Amps flush type complete all as specified and directed by Engineer - in - Charge.

S & F in replacement industrial socket metal clad plug and socket with MCBs single pole 20 Amps complete all as specified and directed by Engineer - in - Charge.

S & F switch piano flush type 5/6 Amp single pole one way complete all as specified and directed by Engineer - in - Charge

S & F switch socket combination 5 pin, 5/6 Amps flush type complete all as specified and directed by Engineer - in - Charge

S&F Switch socket combination 2 in 1, 6 pin , 15/16 Amp flush universal type all as spd and directed by Engr in charge.

S & F Socket outlet 5 pin 5 Amps flush type complete all as specified and directed by Engineer - in - Charge.

S & F ceiling rose, surface bakelite 65x50 mm three terminals complete all as specified and directed by Engineer - in - Charge.

S & F extruded aluminium LED batten channel 20 watt having input voltage AC90-300V, 50Hz, 6500K, with white acrylic cover tube light fitting wall mounted complete with rod, driver and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer - in - Charge. Make :-Havells cat part No. LUMILINEPLUSBS20WLED865SPCSS, Bajaj cat part No. BCLSBAL 20W CW, Crompton cat part No. CCS-100-20-65-HL2-DP-NWH or equivalent cat part as approved by GE

S & F in replacement extruded aluminium LED batten channel 20 watt having input voltage AC90-300V, 50Hz, 6500K, with white acrylic cover tube light fitting wall mounted complete with rod, driver and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer - in - Charge. Make :-Havells cat part No. LUMILINEPLUSBS20WLED865SPCSS, Bajaj cat part No. BCLSBAL 20W CW, Crompton cat part No. CCS-100-20-65-HL2-DP-NWH or equivalent cat part as approved by GE

S & F angle holder insulated body with back plate for conduit fittings complete all as specified and directed by Engineer - in - Charge.

S & F LED lamp 9 W for angle holder complete all as specified and directed by Engineer - in - Charge.

S&F ceiling fan of size 1200 mm sweep with BEE 5 star rating single phase 230 volts, 50 Hz complete 3 blades including canopy, fan hook, hanging rod, fan regulator stepped type complete all asspecified and directed by Engineer - in - Charge. Make : Usha Energia 32 1200 mm 5 star, Bajaj Engery smart 32 1200 mm , Crompton Energion HS 1200 mm 5 star, Havells Efficiencia 5 star 1200 mm

S & F water tight bulk head fitting, comprision of connector galvanised cast iron back plate, weather proof enamelled gallery, glass well and including 10 watt LED lamp complete all as specified and directed by Engineer-in-Charge. Make :-Havells cat part No. HEXAFT10WLED857SSYMBOPC, Bajaj cat part No. BIBWP 10W LED, Crompton cat part No. LBHP-10-CDL or equivalent cat part as approved by GE

S&F in replacement compact decorative energy efficient LED mirror light fitting with antiglare diffuser and decorative end caps suitable for 1x10 watt fitting 2 ft version including LED lamp 10 watt complete all as specified and directed by Engineer - in - Charge. Make :-Havells cat part No. LUMILINEPLUSBS10WLED865SPCSS, Bajaj cat part No. BCLSB 10 WH, Crompton cat part No. LDL-10-CDL or equivalent cat part as approved by GE

S&F in replacement compact decorative energy efficient LED bathroom wall mirror light fitting with bulb power consumption 3.6 W LED and stainless steel and glass frame, key spec : IP 44,SKU : EG130004998 complete all as specified and directed by Engineer - in - Charge. Make :-Havells cat part No. LHJE02206499 (Libra) or equivalent cat part as approved by GE

S&F in replacement round recess mounted LED edge lit slim downlight 12 watt with die- cat aluminum housing fineshed in premium white powder coating efficacy 100lm/w complete all as specified and directed by Engineer - in - Charge. Make :-Havells cat part No. EDGEPRORDDLR12WLED857S. Bajaj Cat part No : BPSLR 12 WH, Crompton cat part no : LSCRM-12W-CDL

S&F in replacement decorative wall mounting, SS finish fixture with opal glass diffuser suitable for 8 watt TU retrofit CFL with accessories and connecting to ceiling rose/point wiring wire complete all as specified and directed by Engineer - in - Charge. Make :-Havells cat part No. LHJC02108499 or equivalent make in Bajaj , Crompton

S & F sheet metal enclosure for double door DB's made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 8 ways, 240 Volts ISI marked , 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S & F in repacement sheet metal enclosure for double door DB's made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 8 ways, 240 Volts ISI marked , 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S & F in repacement sheet metal enclosure for double door DB's made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted SP & N 4 ways, 240 Volts, 200 amps bus bar stove enameled dust and vermin proof suitable for incorporation MCBs and isolators etc complete all as specified and directed by Engineer - in - Charge.

S & F MCB ‘B’ series type suitable for 240 volts, AC supply 5 to 40 Amps , single pole with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F MCB ‘B’ series type suitable for 240 volts, AC supply 5 to 40 Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F in replacment MCB ‘B’ series type suitable for 240 volts, AC supply 5 to 40 Amps , single pole with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F in replacment MCB ‘B’ series type suitable for 240 volts, AC supply 5 to 40 Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F in replacement sub-main wiring with two single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLS stranded copper conductor drawn and including steel dia "medium quantity" PVC conduit including 6.00 Sq mm (Nominal Area) copper cable as earth continuity conductor after chasing in wall and making good the disturbed surface and white wash or existing colour, necessary junction box and cover including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer - in - Charge.

M & L for Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried in ground (earth pit not less than 2.25 Mtr deep below normal ground level with top edge of the plate not less than 1.5 Mtrs below normal ground level, connecting to the Galvanised iron earth lead 4 mm dia GI earth wire, by means of bolts, nuts check nuts and washers of galvanised iron and protection by provision of GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20mm graded stone aggregate with 40mm thick cover of RCC (1:2:4) reinforced with XPM (wieght not less than 4gs/Sqm) and frame of angle iron 25mm x 25mm x 6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed on top edge of earth plate common salt and charcoal filling test point made out of 40mm x 8 mm FI with fixing arrangements, funnel, wire mesh and earth work in hard dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 Mtrs all as per electrical Plate No.3 of SSR Part I and connecting to earth test point including taking our unserviceable earthing with all acessories all as specified or indicated including testing on completionall as specified and directed by Engineer - in - Charge.

Supplying, laying and testing in replacement 10 Sqmmx2 core XLPE insulated, heavy duty electric cable with aluminium conductor 1100 V grade conforming to IS-7098 laid in trenches/ducts/fixed on poles wall/ laid under roads/paths/ drain/ culverts or passing through pipes complete all as specified and directed by engineer in charge.

Supply & filling/ laying a layer of dry coarse sand 8 cm thick before laying ofcable and 15 cm thick after laying of cable complete all as specified and directed by Engineer - in - Charge. Note:- After punning drain 18 cm will be measured for payment.

M&L for brick protection layer with one brick wide using sub class ‘B’ bricks laid flat across the cable complete all as specified and directed by the Engineer in charge.

Note : Amount of credit of Rs 20865.00 for retrieved materials is mentioned in Sch 'A' Section-II of tender documents in pdf form which will be deducted while acceptance of tender offline.

Gyan Chand Marothia Engineer Contractor And Suppliers

PAREEK AND COMPANY

KHANNA CONSTRUCTIONS