SPECIAL REPAIRS TO CHEQUERED TILE PATH AND CERTAIN REVENUE WORKS AT PEDONG UNDER GE 867 EWS

Amount

Surface excavation not exceeding 30cmdeep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth; for foundation, laying of cable etc., or for shafts, wells, cesspits, manholes, pier holes, etc., not exceeding 10 sqm on plan and getting out in soft/loose soil all as specified and directed by Engineer-in-charge.

M&L for Plain cement concrete 1:4:8 mix type D2 (using 40 mm graded stone aggregate) in foundations, filling and mass-concrete etc., all as specified and directed by Engineer-in-Charge.

M & L for modular fly ash bricks as in brick work straight or curved on plan exceeding 6m mean radious built in cement mortar 1:6 complete all as specified and directed by Engineer-in-charge.

M&L for reinforced cement concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) as in walls, retaining walls, basement walls, ballast walls and the like above top of footings, including attached pilasters and buttresses complete all as specified and directed by Engineer-in-Charge. Note: Formwork and reinforcement shall be measured and paid seperately.

Use and removal of steel formwork to faces of walls, retaining walls and the like including attached pilasters, buttresses etc., vertical or to batter for rough finished surfaces of concrete flat all as specified and directed by Engineer-in-Charge.

M&L for Plain or Reinforced cement concrete 1:2:4 mix, type B-1 (using 20 mm graded stone aggregate) as in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands including use of formwork (striaght or curved) all as specified and directed by Engineer-in-charge. Note: Reinforcement shall be measured and paid seperately.

M&L for Mild steel deformed TMT bars 10mm dia and above as in reinforcement to concrete cut to length bent to shape required including cranking bending and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as directed by Engr-in-charge.

M&Lfor Mild steel deformedTMT bars 5mm dia and over up to and including 10 mm dia as in stirrups, spacers and binders , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with and including mild steel wire (annealed) not less than 0.9mm dia all as specified.

M&L for rendering 15 mm thick on brickwork or concrete surfaces in cement mortar 1:4 finished fair and even complete all as specified and directed by Engr-in-charge.

M&L for rendering 10 mm thick on brickwork or concrete surfaces in cement mortar 1:6 finished fair and even complete all as specified and directed by Engr-in-charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement based paint over one coat of primer complete all as specified and directed by Engineer-in-Charge. Make: INDOCEM/ SUPERSNOWCEM/ AQUACEM/ DURACEM

M&L for preparing newly plastered surfaces and applying three coats of white wash complete all as specified and directed by Engineer-in-charge. Make: LOVELYCEM/ SURYACEM/ JANATHACEM / LUCKYCEM or equivalent make as approved by GE.

S&F Mild steel work conforming to Fe 290-0 Gde E-165, as in bands, straps, supports or stays, clamps; hold fasts; wall ties; etc all as specified and directed by Engineer-in-charge.

S&F Mild steel framed work conforming to Fe-290, Gde E-165 steel, such as grilled door with shutters, grills, gratings etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors and similar work all as specified and directed.

S&F rolled mild steel plates (plain or chequered) conforming to Fe-290 (Ged E-165), Square cut or notched (ordinary and counter sunk) forming holes, without any attachment all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws complete all as specified and as directed by Engineer-in-charge. Make: TATA BLUESLOPPE/ LLYODS /JMBS/EVEREST INDUSTRIES LTD/CRILL or equivalent as approved by GE.

M&L for 100 mm thick Plain Cement Concrete 1:4:8, type D2 (using 40mm graded stone aggregate) as in sub base and finishing even and rough to receive toping layer complete all as specified and directed by Engineer-in-charge.

M & L for 40 mm thick plain cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in floor and the like laid in alternative bays in panels, and finishing cement concrete surface even and smooth with using extra cement complete all as specified and directed by Engr-in-charge.

M&L for preparation of new or previously un treated surfaces of steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed. Make: ASIAN/ SHALIMAR/ BERGER/ JENSON&NICHOLSON/IEL/NEROLAC

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil complete all as specified and directed by Engineer-in-charge.

Removing surplus excavated soil to a distance not exceeing 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by Engineer-in-charge.

S&F PVC insulation panels 10 mm thick with EPS struck to 1mm thick plain PVC Sheet of any colour sheet suitably placed in false ceiling with and including GI frame work of size 605 x 605 mm, for seamless celing comprising of GI perimeter chanel 0.55mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and as directed by Engineer-in-charge. MAKE: Rajshree plast wood/Sintex/Nandi or equivalent as approved by GE.

M&L for second class hard wood clean sawn scantling, framed and fixed complete all as specified and as directed by Engineer-in-Charge. WOOD: Sal/Kalasiris/Chaplash/Hollock/Bijasal

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of creosote oil complete all as specified and directed by Engineer-in-Charge.

Demolition of stone slabs or tiles of any description, thickness, laid, bedded and pointed in any mortar and removing rubbish off the premises complete all as specified and directed by Engineer-in-charge.

M&L for 75 mm thick Plain Cement Concrete 1:3:6, type C2 (using 40mm graded stone aggregate) as in sub base and finishing even and rough to receive toping layer including demolition of existing concrete and removing rubbish off the premises complete all as directed by Engr-in-charge.

M&L for cement concrete chequered tiles 300 x 300 x 22 mm thick with grey cement and no pigment, set and jointed in neat cement slurry and pointed in grey cement to match the surfaces as in floors laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed. Make: NITCO/DECO/BHARAT or equivalent as approved by GE.

M&L for rendering 15 mm thick on brickwork or concrete surfaces in cement mortar 1:6 finished fair and even complete all as specified and directed by Engr-in-charge.

M&L for preparing newly plastered surfaces and applying two coats of colour wash over one coat of white wash complete all as specified and directed by Engineer-in-charge. Make: LOVELYCEM/ SURYACEM/ JANATHACEM / LUCKYCEM or equivalent make as approved by GE.

M/S G. K. SUTHAR

C. M. AGARWAL AND CO

MS MAYA PRAKASH GOEL AND SONS

DEEP CHANDRA JOSHI

Sri Gupta Construction

SANJAY MITTAL

GARGO TRADERS