COMPREHENSIVE REPAIRS TO BOUNDARY WALLS DRAINS PATHWAYS FENCING CULVERTS ETC AND OTHER MISC WKS AT RIDGE ROULKI AND NCC OFFR MESS UNDER AGE B/R I AT GE SATWARI

Amount

Demolition of brick work or stone masonry built in cement mortar including all quoins arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles and removing unserviceable material exc 100 mtrs, complete all as specified and directed by Engr-in-Charge

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, removing all type of vegetation (like peeple tree etc) scrubbing down with water and removing all the demolished material outside defence permises complete, all as specified and as directed by Engr-in-Charge.

Demolition of Cement Concrete (un-reinforced) of any description and in any position not otherwise specifically provided and including removing from site to a distance n exc 500 mtrs , complete all as specified and as directed by Engr-in-Charge.

Demolition of Reinforced Cement Concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided and removing the rubbish from the work site out side defence permises, complete all as specified and as directed by Engr-in-Charge.

M&L for 75 mm thick plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in sub base to floors complete, all as specified and as directed by Engr-in-Charge

M&L for 75mm thick Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in sub base to floor, complete all as specified and as directed by Engr-in-Charge.

Providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;complete, all as specified and as directed by Engr-in-Charge

Providing and laying 80 mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;complete, all as specified and as directed by Engr-in-Charge

Material and labour for Cement concrete tiles 30cm x 30cm and 25mm thick, machine pressed; set jointed and pointed in neat cement slurry with grey cement and in floors, and cut and polished , over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes, complete all as specified and as directed by Engr-in-Charge.

Supply and fixing 110 mm bore, PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engr-in- Charge.

Supply and fixing 75 mm bore PVC(SWR) pipes single socket in any length as in weep holes all as specified and as directed by Engr-in-Charge.

Providing cement concrete 1:2:4 type B-0 (using 12. 5 mm graded crushed stone aggregate) in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneeless apex stones , bed plates, roof padding, kerbs not provided for including weathering, slightly rounded or chamfered angles including necessary formwork complete, all as specified and as directed.

Dismantling posts or struts (wood, steel or R.C.C.) embedded in concrete, brick work masonry, etc., any section, including taking out embedded portion and making good disturbed ground complete all as specified and as directed by Engr-in-Charge.

Providing cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregates) as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete, all as specified and directed by Engr-in-Charge.

M&L for Use and waste of form work to sides and sofits ofFormwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter to obtain rough finished flat surface of concrete complete all as specified and as directed by Engr-in-Charge.

M&L for hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and as directed by Engr-in-Charge.

Supply only 2 inch aperture Chain link MS galvanized fencing ( 4mm dia wire) to fix with angle iron with flat iron with suitable nut bolt any size or type complete, all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire, complete, all as specified and as directed.

M&L for mild steel round bars 10 mm dia, fix in chain link fencing using 0.90 mm dia GI wire as strengthing bar complete all as specified.Fe-410-W (Gde.E-250) quality-A or Fe 290 (Gde - E-165), complete all as specified and directed by the Engineer-in-Charge.

M&L for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc 5 cm long, dia of neck 5 to 10 mm complete, all as specified and as directed.

M&L for Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, complete all as specified and as directed by Engr-in-Charge.

Description all as per Srl item No 21 here-in-before but except brick.

Material and labour for precast cement concrete louvers and jallies, 40 mm thick (1:2:4) type B-0 (using 12.5 mm graded aggregate ) set in cement mortar 1:6, including all mouldings and dismantling old U/s broken Jallies at site, complete all as specified.

M&L for RCC (Nominal mix),Type B1 1:2:4 using 20 mm graded crushed stone aggregate as in foundations, including rafts, footings, foundation beam; plinth beams; bases of columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and as directed.

M&L for TMT mild steel bars, 10mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed.

M&L for TMT mild steel bars, 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders and binding with and including MS wire (annealed not less than 0.9mm dia), complete all as specified and as directed.

M&L for 15 mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:4, finish surfaces even and smooth without using extra cement, complete all as specified and as directed.

Preparing newly plastered or unplastered surfaces of wall and applying two coats of cement base paint and including over a coat of chalk whiting, complete all as specified and as directed.

M&L for 100 mm thick Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in sub base to floor, complete all as specified and as directed.

M&L for 100 mm thick Plain cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in sub base to floor, complete all as specified and as directed.

M&L for forming 12mm thick ( thickness of concreat slab 100 mm) Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ complete, all as specified and as directed.

M&L for Plain cement concrete 1:3:6 type C-1 (using 20mm graded aggregate) as in surface channel and drain including all necessary form work, complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.complete, all as specified and as directed by Engr-in-Charge

Preparation of new steel surfaces (with rubbing sand paper) of any description, over 10cm in width or girth, applying two coats of synthetic enamel paint and including over one coat of red oxide primer complete, all as specified and as directed.

M/S PAWAN KUMAR ANAND

S S CONSTRUCTION

M/S Shesh Paul Gupta