Construction of solar passive Boys Hostel 50 bedded at Government Degree Collage Diskit Nobra

Amount

Civil Items. Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil . including cost of carriage compltete job.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)including carriage complete job.including cost of carriage compltete job.

Providing and fixing up to floor five level precast cement concrete solid blocks including hoisting and seating in position with cement mortar 1:3 (1: cement 3: coarse sand), cost of centering, Shuttering and complete. Crushed 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20mmm nominal size)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for: A, Foundations, footings, bases of columns etc. for mass concrete.

B, Lintel, beams, plinth beams, girders, bressumers and cantilevers.

C,Columns, pillars, piers, abutments, posts and struts.

E, Suspended floors, roofs, landings, balconies and access platforms.

F, Edges of slabs and breaks in floors and walls Under 20 cm wide

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. a) works upto plinth level

b) All works above plinth level upto floor V level

COMPRESSED STABILISED EARTH BLOCKS (CSEB) in superstructure above plinth level upto floor five level and curing complete in:Cement mortar 1:6 (1cement : 6 coarse sand)Critical parameters related to finished CSEB:- Dry density 1750 kg/m3 Water absorption Less than 15% Dry Compressive strength More than 2.8N/mm2 Wet Compressive strength More than 1.2 N/mm2 Flexural strength (bending strength) More than 0.5 N/mm2 Pitting depth (Erosion resistance) Less than 10 mm Linear expansion of block upon saturation with water Less than 0.10% Critical parametersof soil for CSEB block production:-Sand and gravel More than 65%Silt 5% to 20% Clay 10% to 15% Plasticity Index Less than or equal to12 Phvalue Between 6 and 8 Stabilizer:- Cement Not less than 5%

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

Stone tile work for wall lining upto 10m height with special adhesive likearaldite or equivalent over 12mm thick bed of cement mortar 1: 3 (1 cement: 3 coarse sand) including pointing in white cement with an admixture of pigment to match the stone shade.Granite stone of any colour and shade

Providing and fixing Ist quality ceramic glazed wall tiles conforming toIS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black ofany size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing of Locally available Hard wood wooden wall Panelling 20mm thick over 12mm is 303 Plywood of approved make with all necessary screws with complete including Polising as per architectural design and directions of Engineer- in-charge

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): First class kail wood

Providing and fixing ISI marked flush door shutters conforming to IS: 2202(Part I) decorative type, core of block board construction with frame of 1st classhard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of requiredsize with necessary screws 40mm thick.

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Providing and fixing factory made PVC door frames of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and jointed with two numbers of 150mm long brackets of 15x15mm MS square tube, the vertical door profiles to be reinforced with 19x19mm MS square tube of 19 gauge, EPDM rubber gasket weather seal to be provided throughout the frame. The door frame to be fixed to the wall using MS screws of 65/100mm size complete as per manufacturers’ specifications and directions of engineer-in-charge Fenesta/Sain Gobin

Providing and fixing 30 mm thick factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2) thick, Fenesta/Sain Gobin

Providing and fixing factory made UPVC Colour ( as approved by the engineer ) casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Casement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.50 sqm).9.149A.5 Casement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.50 sqm).Fenesta/Sain Gobin

Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/top hung UPVC windows, of approved quality, with necessary stainless steelscrews etc. as per direction of Engineer-in-charge.

Providing and fixing casement handle made of zinc alloyed (white powder coated) for UPVC casement window with necessary screws etc. complete.

Providing and fixing of traditional Ladakhi Shingstag of height 2 feet in 2nd class kail wood as per drawing complete in all respects (including polishing, cement concrete coping , fasteners which to be paid separately) including cost of transportation, labour, wood, wastage, taxes, profits etc as per directions of Engineer- in-charge

Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 40mm thick with 20 mm nominal size stone aggregate.

Prelaminated flooring (Engineered wood flooring) 12 mm thick top layer with foam base layer 4mm thick over cement concrete flooring 40 mm thick

Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing, cleaning and curing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) .Light shade using white cement

Providing and laying Ceramic glazed floor tiles of size 600x600 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc.,complete.

PP-R PIPES AND FITTINGS Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge. 19.2.2 Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. PN-16 pipe , 25mm OD(SDR-7.4) including cost of carriage compltete job.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand)including grouting the joints with white cement and matching pigments etc. complete Tiles size 800x800 mm

Providing and laying Vitrified tiles in different sizes (thickness to bespecified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours and shades,in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), including grouting the joint with white cement and matching pigments etc. complete. Tiles size 800x800 mm

Providing and laying Polished Granite stone flooring in required designand patterns, in linear as well as curvilinear portions of the building allcomplete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing (PU) Polyurethane 50mm thick of density 28kg -38 kg/ CU .M in between cavity wall. Density 24 kg/sqm

Providing, fixing and applying Plaster of Paris (POP) false ceiling consisting of frame work made with 50mm sq M.S. tubes of 18 G thickness as main runner at 600 mm c/c both ways, suspended/ supported with M.S. flats 25x4 mm from existing R.C.C. slab, finished smooth to line and level including necessary supports, scaffolding etc. as required and also including applying a coat of red oxide zinc chromate primer over the M.S. frame work and suspenders complete. Including providing and fixing expanded metal of size 5.25 mm x 1.25 mm thickness welded to main runners and applying POP (calcium sulphate semi hydrate variety) to the expanded metal of thickness not less than 10 mm

Providing and Fixing 15 mm thick densified tegular edged eco-friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanizing @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main ’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting onperiphery walls /partitions on Perimetre wall angle pre-coated steel size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws@ 230 mm interval and laying 15 mm thick densified edges calcium silicate ceiling tiles of approved texture (Spin tone / Cosmos/hexa) in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanized steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’ , bottom exposed with 24 mm of all T-sections shall be prepainted with polyester baked paint, for all heights, as per specifications,drawings and as directed by engineer-in-charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs)having area less than 0.30 sqm. The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non - combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/m 0 KC.

15mm Cement plaster on the rough side of single or half brick wall of mix:1 : 6 ( 1 cement : 6 fine sand)

6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand) 1 : 3 ( 1 cement : 3 fine sand) Cement must be PPC with minimum 25% flyash content

Pebble dash plaster up to 10m height above ground floor with a mixture of washed pebble or crushed stone 6mm to 12.5mm nominal size dashed over and including fresh plaster in two layers, under layer 12mm cement plaster 1:4 (1 cement : 4 coarse sand) and top layer 10mm cement plaster with cement mortar 1:3 (1 cement : 3 fine sand) mix with 10% finally grounded hydrated lime by volume of cement.

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications:Two or more coats applied @ 1.25 liter/10sqm over and including one coat of special primer applied @ 0.75liter /10sqm

Polishing on wood work with ready mixed wax polish of approved brand and manufacture:

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement: 3 coarse sand) including making joints with or without grooves (thickness of the joints except at sharp curve shall not to be more than 5mm) including making drainage opening wherever required complete etc. as per direction of Engineer-in charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge)

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern

Providing and fixing in position precast R.C.C. manhole cover and frame

Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with common burnt clay (non modular) bricks of class designation 7.5 bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with with water proofing cement compound @ 0.253kg/ sqm. This layer will beallowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm . This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately.

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservoir, sewage & water treatment plant, tunnels / subway and bridge deck etc.,prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of selfhealing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-incharge. The product performance shall carry guarantee for 10 years against any leakage.

Providing and fixing double glazed units(DGU) comprising 6 mm thick glass on either side with 12 mm thick inert gas gapin The DGUs shall be processed from reputed glass processors.

Sanitery Works, Providing and fixing sound insulated Polyproplene piping system as per ON EN 1451-Part 1-6 & EN 12056 Part 1-5 with 3 layer pipe made of PP-C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 22 dBA as per DIN 4109 at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, density of pipe = 1.25gms/cm3, elongation = 0.05mm/m0K and tensile strength > 24 N/mm2,with all necessary fittings in blue colour, fitted with factory fitted lip ring incluiding painting with ordinary cement based paint for external installation. (POLOPLAST - PKNG) a) 110 mm dia

b) 150 mm dia

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :100mm diameter S.W. / RCC pipe

150mm diameter S.W. / RCC pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 150 x 100mm size P-type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design a) Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) ith common burnt clay F.P.S. (non modular) bricks of class designation 7.5

b) Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes Size 90 x 80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes Size 90 x 80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m all kinds of soil.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing PVC piping system as per ON EN 1451-Part 1-6 & EN 12056 Part 1-5 with 3 layer pipe made of PP-C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 22 dBA as per DIN 4109 at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, density of pipe = 1.25gms/cm3, elongation = 0.05mm/m0K and tensile strength > 24 N/mm2,with all necessary fittings in blue colour, fitted with factory fitted lip ring incluiding painting with ordinary cement based paint for external installation. a) 75 mm dia

b) 110 mm dia

Providing and fixing PVC piping system as per ON EN 1451-Part 1-6 & EN 12056 Part 1-5 with 3 layer pipe made of PP-C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 22 dBA as per DIN 4109 at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, density of pipe = 1.25gms/cm3, elongation = 0.05mm/m0K and tensile strength > 24 N/mm2,with all necessary fittings in blue colour, fitted with factory fitted lip ring. (POLOPLAST - PKNG) - For indirect waste/sinks, wash bassin etc.) a) 40mm dia.

b) 50 mm dia

Providing and fixing PP white Trap (HC 46 (INDIA)) with minimum 50mm water seal with rubber seal on inlet to push fit hopper for indirect waste connections 110 mm dia

Providing, fixing, testing and commissioning of pipe inlet fittings fabricated with P.P. Pipe with maximum 3 inlets 40, 50 & 75 mm OD size poloplast pipe, ( or by Fixing Tee 110 x 50/110x75 mm and connecting waste pipe by making header ( pipe will be measured included fittting in RMT. )) fixed to 'P' traps including Dripseal/Pipe seal/solvent weld joint/rubber ring joint complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work up to plinth level. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. (For rain water pipe)

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge. a) PN-20 to 25 pipe , 25mm OD as directed by the site engineer. inernal

b) PN-20 to 25 pipe , 32mm OD as directed by the site engineer.

c) PN-20 to 25 pipe , 40mm OD as directed by the site engineer.

d) PN-20 to 25 pipe , 50mm OD as directed by the site engineer.

e) PN-20 to 25 pipe , 65mm OD as directed by the site engineer.

f) PN-20 to 25 pipe , 90mm OD as directed by the site engineer.

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge. PN-20 to 25 pipe , 25mm OD as directed by the site engineer. External. PN-20 to 25 pipe , 50mm OD as directed by the site engineer

Providing and fixing high pressure Float Valves of PN-6 rating for Overhead water tanks.50mm nominal bore

Providing, fixing, testing & commissioning of lever operated gun metal ball valve with SS ball.25mm nominal bore

32mm nominal bore

40mm nominal bore

50mm nominal bore

Providing, fixing, testing and commissioning of Air Release Valves screwed ends with ball valve of approved brand of manufacture, with accessories etc., complete. 15mm dia

Providing, fixing, testing & commissioning of class-O nitral sheet insulation 6mm thick to hot water pipe and fittings and valves as per manufacturer's recommendations complete to satisfaction of Engineer in charge. a) 25mm dia 19 mm thick

b) 32mm dia 19mm thick

Providing and fixing insulation to Pipes with 50mm thick resin bonded preformed mineral wool pipe sections of density not less than 144 kg/cum. as per IS:9842 and applying 26g Aluminium sheet as cladding, properly rolled and grooved with joints sealed with a strap of roofing felt (type-III Grade-I conforming to IS:1322) complete with self tapping screws centre to centre distance of 150mm to close cladding joints. The pipes shall be painted with zinc chromate primer before applying insulation a) .25mm nominal bore

b) 32mm nominal bore

c) 40mm nominal bore

d) 50mm nominal bore

e) 65mm nominal bore

f) 80mm nominal bore

Providing & fixing M.S. Puddle Flange fabricated of 600 mm long 'C' class pipe pieces with screwed ends with center of pipe welded with 6mm thick M.S. plate of size (100mm+D) X (100mm+D) for R.C.C. water tank walls / slabs. The entire fitting shall be hot dipped galvanised. (D indicated above nominal dia metre of pipe in mm). a) 25mm dia

b) 50mm dia

c)65mm dia

d) 80mm dia

e) 100mm dia

f) 150mm dia

Providing, fixing, testing & commissioning of 450x600mm rectangular C.I. Cover (IS : 1726-91) with frame light duty total weight 38 kg. (23 kg. cover and 15 kg. Frame (for overhead tanks).

Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified 80mm dia

Supplying and fixing 50mm thick aluminium foil faced resin bonded fibre glass insulation (on duct) of density 24 kg/cu.m after applying two coats of cold setting adhesive (CPRX compound) sealing all joints with self adhesive aluminium tape & covering with 0.63mmx19mm GI wire mesh netting & butting all joints and laced with GI wire complete and finally covered with one layer of tar felt stuck with hot bitumen as per specifications and as required. (for outdoor applications) (Inuslation for HDPE tank).

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

roviding and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.(For wash basin)

Providing and fixing stainless steel A ISI : 304 (18/8) kitchen sink as per IS : 13983 with CI brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls where required.Kitchen sink with drain board 510 x 1040mm bowl depth 250mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe Flexible pipe

Providing and fixing CP Brass long body bib cock of approved quality confirming to IS standards and weighing not less than 690 gms. 15mm nominal bore

Providing and fixing C.P brass angle valve for basin mixer and geyser points of approved quality confirming to IS:893115mm nominal bore

Providing and fixing toilet paper holder.CP Brass

roviding and fixing CP brass Sink Mixer,

Providing and fixing C.P. brass twin robe hooks

Providing, fixing, testing & commissioning S.S. hinged grating, 1.5mm thick with frame

Providing and fixing automatic high pressure electric water heaters with glass lining thermostats with each element and high temperature cut off, necessary insulation, safety valve, etc. all complete. a) 25 ltter

b) 35 litter

c) 50 litter

Providing and Fixing Health Faucet make with flexible pipe and wall hook with each European W.C. Pan.

Providing, fixing, testing & commissioning CP concealed body single lever diverter with 40mm cartige

Providing, fixing, testing & commissioning CP single lever exposed parts kit of divertor .

Providing, fixing, testing & commissioning CP brass shower rose with shower arm.

Providing, fixing, testing & commissioning CP brass bath spout with wall flange .

Providing, fixing, testing & commissioning C.P. brass soap dish including cutting and making good the walls wherever required complete to the satisfaction of Engineer in charge.

Providing, fixing, testing & commissioning C.P. brass Towel Rail 24".

Providing and fixing 15mm C.P. brass Connection Pipe (450mm Long Braided Hose with Two 15mm Nuts & Rubber Washers Without Nipple (Suitable for WC, Geysers & Basin Mixers)) or equivalent make union nuts complete with C.P. brass flange including cutting and making good the walls wherever required. (For Angle Valve)

providing and fixing mirror of superior quality with necessary fittings.

Providing, fixing, testing, & commissioning of SWING HANDICAP GRAB BAR - S.STEEL (Euronics model no EGR S02) For phsically handicapped toilet.

Providing, fixing, testing, & commissioning of S.STEEL GRAB RAIL (600 MM),32MM DIA. (Euronics model no EGR01(600MM)) For phsically handicapped toilet.

Providing and fixing Solar Water Heating system complete with solar panels, insulated SS 304 storage vessel with cemamic lining inside & interconnecting pipes and valves complete in all respect as per manufacturer specifications. Tank shall be supplied without electrical boosters. (Solar heaters shall be equivalent to sholarhart model LCSC Thermosiphon solar heating system and suitable for frost & harsh condition.) (The Vendor shall include in this rate cost of all interconnecting pipes and valves & insulations connecting the panels). Capacity 300 LPD (comprising 2 nos. collector panels and 300 ltres SS 304 storage vessel)

Providing, fixing, testing, and commissioning of 200 lph capacity reverse osmosis plant comprising of all equipments & accessories as per specifications and all necessary inter connecting pipe work and valves, electrical panls & cabling, including all foundation works required for various water treatment equipment. The RO plant in general shall comprises the following equipment and accessories.The RO plant in general shall comprises the following equipment and accessories. SS R.O. feed pumps - 2 Nos. (1W + 1S) Multigrade Filter - 1 No. Activated carbon filter - 1 No. Antiscalent dosing system-1 No. High pressure pumps - 2 Nos. (1W + 1S) RO membrane & housing PH correction System – 1 No. Instrument panel – 1 No. Conductivity indicator - 1 No. PH indicator - 1 No. Flow indicator - 2 Nos. Flow meter with totalizer - 2 Nos. Pressure Indicator - 7 Nos. Pressure switches - 2 Nos. Electric Power Panel – 1 Set. All inter connecting pipe work and valves – 1 Lot. Memberane cleaning system – 1 No. Drainage arrangement for disposal of rejected water from RO system Including making connection with the nearest drain All foundations for electrical & mechanical equipment. Any other item required for satisfactory completion of work. Recommended spares for 2000 hours of normal operation - 1 lot. All piping works and associated valves including supports, valve chambers and manholes etc. All mechanical and electrical works including motor control panels, cables etc. connected with the plant. All RCC and Masonry works related with Reserve Osmosis plant and related foundation works for electrical mechanical equipment. Any other work necessary for satisfactory performance of the system. The tenderer shall be required to execute as a part of scope of work, any other item not specified above and indicated in the tender but essentially required for satisfactory and desired functioning of the plant. The tenderer shall provide a defined scheme based upon this process along with sizes of different tanks and equipment and take guarantee of the treated water to the due standard. Submittals required along with the offer. Tenderer shall submit following documents along with the offer. P & I diagram of entire installation indicating sizes, material of all interconnecting pipes and valves, instrumentations and capacities of all equipment of RO plant. Data sheets of all equipment and accessories considered in offer. SLD of electrical control panel of RO plant.

Providing, fixing, testing and commissioning SS tanks (Model No.-CVM/08-09/05) including hosting at desired height complete with all interconnections pipes and all inlet, outlet, overflow and scour connections.Capacity=500 litres

Electrical Works, Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group- A

Group- B

Group- C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

b) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

c) 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

d) 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

e) 4 X 6 sq. mm + 2 X 6 sq. mm earth wire

f) 4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. A) 3 x 1.5 sq. mm

b) 3 x 2.5 sq. mm

c) 3 x 4 sq. mm

d) 3 x 6 sq. mm

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 pair

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. a) 20mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required a) .5/6 A switch

b)2 way 5/6 A switch

c) 15/16 A switch

d) 3 pin 5/6 A socket outlet

e) 6 pin 15/16 A socket outlet

f) Telephone socket outlet

g) TV antenna socket outlet

h) Bell push

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)

6 Module (200mmX75mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Providing and fixing plain 16/0.20mm (0.50sqmm) twin flat flexible, FRLS PVC insulated, copper conductor cable, in PVC sleeve of suitable size on the floor/ wall, or side of the table/ door etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.Upto 450 mm sweep

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. A) 1 run of cabble

b) 2 run of cable

c) 3 run of cable

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A

Group B

Group C

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) a) 6 way (4 + 18), Double door

b) 8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. A) Single pole

b) Double pole

c) Triple pole and neutral

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. a) 100 mm width X 50 mm depth X 1.6 mm thickness

b) 150 mm width X 50 mm depth X 1.6 mm thickness

c) 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. a) 100 mm width X 50 mm depth X 1.6 mm thickness

b) 150 mm width X 50 mm depth X 1.6 mm thickness

c) 300 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Reducer" (galvanisation not less than 50 microns) with perforation not more than17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. a) 150 mm width X 50 mm depth X 1.6 mm thickness

b) 225 mm width X 50 mm depth X 1.6 mm thickness

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required.

Fire Fitting Work. Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.Suitable cement concrete foundation duly plastered and with anti vibration pads.450 lpm at 35 m Head

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required

Providing, laying, jointing, testing, & commissioning the PVC insulated & sheathed FRLS Armoured cables of 1.1 K.V. Aluminium Conductor including supplying and making end termination with brass compression glands: 3 core x 10 sqmm

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.100 mm dia pipe

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required a) 25mm dia

b) 80 mm dia pipe

c) 100 mm dia pipe

d) 150 mm dia pipe

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required.20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.30 m

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required . 80 mm dia

100 mm dia

150 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :100 mm dia

Providing, fixing, testing & commissioning of Drainage Provision for the risers with necessary 40 mm dia pipe, ball valve etc as required. Maximum length of pipe shall be 10 M.

Providing, fixing, testing & commissioning of 25 mm dia screwed inlet forged brass single acting air valves connected with ball valve on inlet side at top of the Risers.

Providing and fixing in position the industrial type Pressure Gauges with gun metal / brass valves complete as required

Providing, fixing, testing & commissioning of door with frame for all internal fire hydrants fabricated from 18 gauge CRCA M.S. sheet double door including 2 nos allen key lock for locking along with padlock arrangement & fully glazed with 5 mm thick float glass approved by local Fire Authority, stove enameled fire red finish with " fire hose' written on front with radium strip suitable to house 15 mm long four length of canvas hose with couplings, one no of branch pipe, one fire mans axe and two numbers of portable extinguishers, first aid fire hose and supports for hoses, branch pipes, Axe and hose reel. as per approved design including necessary fixing arrangement for hoses & axe and branch pipe.).

Providing, fixing, testing & commissioning of standard Fireman's Axe with heavy insulated rubber handle.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :2 way-100 mm dia M.S. Pipe

Providing, installation, testing and commissioning of ABC type fire extinguishers consisting of welded MS cylindrical body, squeeze lever discharge valve fitted with pressure indicating gauge internal discharge tube, 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket, conforming to ISI finished externally with red enamel paint and fixed to wall with brackets complete with internal charge.Capacity 6 kg. I.S.I. Marked.

Providing, installation, testing and commissioning of Carbon-di-oxide fire extinguishers consisting of welded M.S cylinderical body,squeeze lever discharge valve fitted with internal dischargetube, 30cms long high pressure discharge hose, discharge nozzle, suspension bracket, confirming to IS : 934 finished externally with red enamel paint and fixed to wall with brackets with rawl plug/dash fasteners complete with internal charge.Capacity 4.5 kg. I.S.I. Marked.

VOLUME CONTROL SWITCHES Rotary volume control switches heavy duty type for above transformers with `ON' `OFF' facility. The volume control switch can be either in stepless version or 7 stepped click free version housed in metal. box.

SPEAKER WIRING Speaker wiring in 20 mm dia PVC. conduits with twin twisted 40/0.2 mm 2 core loudspeaker cable.

INTERCONNECTION WIRING WITHIN MUSIC ROOM Interconnecting wiring with-in music room between amplifiers / cassette players, M.D.F. complete as required.

AMPLIFIER Supplying, installing, testing & commissioning of Amplifier with following specs. and 500 watts P.M.P.O ( Heincrich -HPA1480) Class AB Amplifier 5 Mic, 3 Aux & 1 Telephone inputs. 2 Balanced Mic inputs through Combo (Female XLR socket cum 1/4" Stereo Phone Jack) connectors. Mic-1 and Telephone input provided with Voice Operated Priority over all other programmes. Preamplifier and Line Output for recording the programme and connecting to a booster amplifier. Line input for connecting an external audio mixer or permitting to be used as a Booster Power Amplifier. Resettable circuit breaker for protection against overload and short circuit. Instant transfer to DC Power (Car Battery) if AC power fails. 19" Rack mountable.

Supply, Installation, Testing and Commissioning o IP Dome Fixed IR PoE Camera, 1/2.8",2 Mega Pixels, Full HD, 1920 x 1080p at 30FPS, 2.8 mm fixed lens, Horizontal field of view >110°, .06 lux, mechanical IR filter, dual streams , IR range minimum 30 Meter, H.264 , any IRIS type, true day-night, noise reduction, ONVIF profile S, certifications - CE, UL, FCC, operating humidity 10-90% RH (non-condensing) or better, PVC free, WDR , IP 66 & IK10(Make-Bosch/ Honeywell/Axis)

Supply, Installation, Testing & Commissioning of 32 channel NVR to view and record 32 IP cameras at Full HD(1080p Resolution) at 25 FPS. The NVR shall have 8 HDD slots.HDD of 18 TB to be provided to enable motion based recording for 30 days(Make-Pelco/ Bosch/ Axis)

Supply, Installation, Testing and Commissioning of 32" LED Color Monitor(Make-Sony/ Samsung/ LG)

Supply, Installation, Testing and Commissioning of managed LAYER 2 10/100/1000 NETWORK POE SWITCH 24 PORT(Make-Cisco/ HP)

Supply, laying, Testing and Commissioning of Cat 6 /UTP Cable(Make-AMP/ R &M/ Belden)

Supply, Installation, Testing and Commissioning of Cat 6, 24 port loaded Straight patch panel with labels and label covers, Height 1 U

Supply, Installation, Testing and Commissioning of Cat 6 UTP RJ45 Patch Cords, 1 Mtr(Make-AMP/ R &M/ Belden)

Supply, Installation, Testing and Commissioning of 6 U INDOOR Network Rack including with fan, Cable Managers & 5 Amp. PDU Unit(Make-Natrack/ Valrack/ Rittals)

Supply, Installation, Testing and Commissioning of 25mm FRLS PVC conduit( Make-B.E.C. / ESC )

Supply, Installation, Testing and Commissioning of 25mm PVC flexible conduit (Make-B.E.C. / ESC )

Supply, fabrication, installation of steel fabricated cable supports/ Light fixture supports including, welding, grouting and painting as required.

P.A. JUNCTION BOXES Music junction boxes fabricated out of 18 gauge C.R.C.A. sheet duly powder coated with 12 nos. male / female connectors duly mounted with in the box.

Light Fixtures Supply of 9-10W LED downlight recess mounting luminaire, Aluminium powder coated white after phosphochromate treatment with system lumen efficacy of >100lm/W to enhance the lumen output with Output Short-circuit protection, Surge protection. Lumen Output of 1000 lumens.CRI >80, Color temperature 5700K, THD <10% and PF >0.95,IP20,Life class of 50,000 hrs @ L70, Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:3 KV. Havells Cat Ref- INTEGRAHEDLR10WLED857S or similar from approved makes

Supply of 18-20W LED downlight recess mounting luminaire , Aluminium powder coated white after phosphochromate treatment with system lumen efficacy of >100lm/W with Output Short-circuit protection, Surge protection . Lumen Output of minimum 1800 lumens.CRI >80, Color temperature 5700K, THD <10% and PF >0.95,IP20,Life class of 50,000 hrs @ L70, Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:3 KV. Havells Cat Ref- INTEGRAHEDLR18WLED857S or similar from approved makes

Supply of 18W linear 4ft LED for wall and ceiling mounting integrated batten made of ultra slim co-extruded polycarbonate channel with housing part in white finish & diffuser part in reeded opal finish.White finish ABS end caps with decorative circular coloured polycarbonate cap snap fitted on the end cap to enhance the aesthetic of the fixture. High efficiency long life LED with lumen efficacy of 130 lm/W with viewing angle of 120º.Powered by an integral isolated low THD electronic LED driver. Lumen Output of 1860 lumens with System efficacy of >105lm/W .CRI >80, Color temperature 3000K, THD <20% and PF>0.95,IP20 . Life class of 35,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:3 KV. Havells Cat Ref. LUMILINEBS18WLED80S57CWH OR similar from approved makes

Supply of 40W linear 4ft LED for wall and ceiling mounting integrated batten made of ultra slim co-extruded polycarbonate channel with housing part in white finish & diffuser part in reeded opal finish.White finish ABS end caps with decorative circular coloured polycarbonate cap snap fitted on the end cap to enhance the aesthetic of the fixture. High efficiency long life LED with lumen efficacy of 130 lm/W with viewing angle of 120º.Powered by an integral isolated low THD electronic LED driver. Lumen Output of more than 3600 lumens with System efficacy of >105lm/W .CRI >80, Color temperature 3000K, THD <20% and PF>0.95,IP20 . Life class of 35,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:3 KV. Havells Cat Ref DURABS40WLED865SPCSS or similar from approved makes

Supply of Decorative bracket light with 9-10 W retrofit bulb. Havells Stylo

Supply of Exhaust fan Ventil Air 200 MM or equivalent

Supply of 9-10 W Bulk Head light fixture Pressure Die Cast with IP66 protection & IK09 impact Resistance Havells HEXAFT10WLED857SSYMBOPC

Electrical Panel Design, Manufacture, Supplying, Fixing, Testing and Commissioning of Panel made of 16 S.W.G.C.R.C.A. sheet, steel dust and vermin proof compartmentalized construction with bus bar chambers, cable alley, cable glands plate etc. as required duly painted from inside as well as out side, as below:- ELECTRICAL PANEL BOYS HOSTEL INCOMER 1 Set of 250 Amps. 415 Volts 4P. M.C.C.B. of 25 KA with overload, S/C and earth fault protection MAIN BUS BARS 1 Set of 315-Amps 3 phase 4 wire 415 volts 50 HZ Aluiminium bus bars with colour coded PVC heat shrinkable sleeves (Neutral to be equal to phase size). METERING 1 Sets of Digital multi function meter with 250/5A CTs,CT shorting links R/Y/B LED indicating lamps and 2A control SP MCBs 1 Set of LED indicators for Incoming Breaker 'ON', 'OFF', 'TRIP' LED lamps. OUTGOINGS 5 Nos. 100 Amps. TPN MCCB of 25 KA with builtin protections 5 Nos. 63 Amps. TPN MCB of 10 KA

Inverter, Supply, Installation, Testing and Commissioning of Bidirectional DSP controlled IGBT based Single Phase 5KVA Inverter complete with following specification, suitable to work as per Nubra Valley, LADAKH enviormental conditions In-put power supply : 230 V (+10%,-15%) 50 Hz (± 6%), Single phase + Neutral, Output power supply : 230V 1 Phase 50Hz, Pure sinusoidal waveform, Overload capacity of 110% for 10 minutes, Protected against output overload,short circuit, D.C. input, Low / over input voltage Low / Over, Battery pre-exhaust alarm at-least two minutes before ‘DC Low’ tripping, Forced Air cooled etc. (Quoted cost shall be inclusive of connected cabling) Approved Make:- Luminious, Microtek, Su-Kam,LIVFAST,LIVGUARD

Supply, Installation, Testing and Commissioning of Flood inverter grade lead acid battery bank for 30 minutes backup at full load. Battery Calculation to be proviced by supplier Approved make:- Exide, Rocket, Amararaja,( But China Made not acceptable for any make)12V-150AH-8 NOS for each set of inverter

Supply & Installation of Open Battery Rack & Interlinks

Lift/ Elevator Design , supply , Installation and commissioning of one No eight persons ( 544 kgs or 8 persons ) with the speed of 1m/sec. four stop and four opening , travel hight of 12 mtrs, the elevator has to be techninally vatted by the competant authority and it should be certificated by the competant authority including maintanence of the lift/ elevator for the three years after commissioning of the lift ( inclusive of all accessories and electrical cablings etc complete job ) the elevator should be of , KNNE,OTIS, or MUTSHIBSHI

M/S TSASKAN CONSTRUCTION COMPANY

M/S TONYOT TASHI