Repair of roofing sheet ,leakage seepage, plastering ,water proofing treatment ,chajja ,facia and other certain work at Sewar Fort and parade ground Bharatpur Mil Stn

Amount

M&L for Rendering 15 mm thick in CM (1:4) on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing complete all as specified & as directed

All as per item no 1 above but in CM (1:6) fair face of brick-work finished even and smooth without using extra cement complete all as specified & as directed

M&L for rendering 15 mm thick in CM (1:4) on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing upto 10 m height Including Taking down cement plaster of any description etc including racking out joints,hacking for key, scrubbing down with water all as specified & complete all as specified & as directed

All as per above item no 3 above but in CM (1:6) finished even and smooth without using extra cement complete all as specified & as directed

M&L for Rendering 5 mm thick in cement and sand mortar 1:3 on fair faces of cement concrete surfaces of ceiling of chajjas/roof protection etc including finishing the surface even and smooth without using extra cement Including Taking down cement plaster of any description etc including racking out joints,hacking for key, scrubbing down with water all as specified & complete all as specified and as directed

M&L for demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) as in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and as directed

M&L for fixing of sunroof stone (of approved quality) of thikness 40mm, wherever required as per approved design, including inserting/fixing of stone up to 9m height.Complete all as spcfd & as directed . Note :- Quoted rates are includes cost of material , ,safety measures/ use of specified equipments for workers of building required to complete the work at 9m heights & including all leads complete all as specified & directed

Demolition of brick masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings,dressed stone work and precast concrete articles as spd and directed by Engr-in-Charge.

M&L Brick work with sub class 'B' old size bricks bricks straight or cured on plan exceeding 6 m mean radius built in cement mortar 1:6

Ditto item No 09 but except bricks

M & L Preparation of new plastered or un plastered surface of wall including cornices, pilasters etc by brooming down and applying two coats of distemper oil emulsion white or tinted over a coat of wall primer wash with hand roller & 1 mm wall care putty (in Two Coats) complete all as specified and as directed

M&L Preparation of new plastered surfaces of walls or un plastered surface and applying two coats of cement base paint over a coat of primer with hand roller complete all as specified and as directed by Engr-in-Charge.

M&L Preparation of newly plastered surfaces of ceiling & applying three coats of white wash complete all as specified and as directed .

M&L Preparation of newly plastered surfaces of Wall & applying three coats of white wash complete all as specified and as directed .

Demolition of cement concrete unreinforced in ground floor and paving n.exc 15 CM thickness (below or above GL) complete all as specified and as directed ..

M&L providing cement concrete type B-0 1:2:4, (using 12.50mm graded stone aggregate) as in roof kerbs, benching, rounded or chamfered on edges. complete all as specified and as directed

M&L for PCC (1:4:8) type D-2 using 40mm graded crushed stone aggregate as in foundation/mass concrete complete all as specified & as directed.

M&L for 10mm thick rendering in CM (1:3) as in old RCC roof surfaces and sunken or concrete surfaces mixed with water proofing compound finished fair and even complete all as specified and directed.

M&L water proofing treatment to roof slab & sunken portion with APP modified polymeric membrane centre core 100 micron HMHDPE outer film 20 micron each having weight not less than 3 Kg/sqm with 100mm overlap laid as per manufacturers instructions complete all as specified and directed by Engineer-in-Charge with following courses of descriptions below :- (a) Applying evenly a coat of bituminous primer confirming to IS-3384-1965 @ 0.40 Kg/Sqm on prepared surface till the surface is properly impregnated. (b) Second coat of bonding material using blown gr ade bitumen 85/25 confirming to IS-702 @ 1.20 Kg per Sqm. (c) Third course ie laying of APP modified membrane described hereinbefore with 100mm over lap in longitudinal direction and 100mm in transverse direction all joints and changes in all directions should be curved with cement mortar (1:3) mixed with SBR latex @ 200ml per bag of cement and curved well before alying the membrane complete all as specified and directed. (d) Fourth coat bonding material using blown grade bitumen 85/25 confirming to IS-702 @ 1.20 Kg per Sqm.

M&L for cement concrete type B1 (1:2:4 ) using 20 mm graded stone aggregate as in padding, roof kerb incl hunching, benching etc RCC pillar, Beam and sunken portion area etc complete all as specified and directed.

M&L PCC (1:3:6) type C-2, using 40mm graded stone aggregate, 75mm thick finished even & smooth using extra cement.

M&L 25mm thick PCC (1:2:4) type B0, (using 12.5mm graded stone aggregate) as in floor complete all as specified & directed .

M&L for 40mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate as in flooring finished even and smooth with using extra cement complete all as specified and directed.

Supply only glass dividing strips 3mm thick and 38mm wide & fixed in position as directed complete all as specified and directed. .

M&L dismantling floor,heart or wall tiling including cement mortar bedding (but not backing) , removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for coloured digital/matte/glossy/ tiles in pattern/combination in vertical surfaces , of size 300mm x 200mm etc, 7 mm thick over and including 10 mm thick rendering in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed.

M&L for coloured/ matte finish Non Skid Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm , over & including 15 mm thick screed bed in CM 1:4 in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed by Engineer-in-charge.

M&L for Coloured / matte finish Non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm bur not exceeding 0.38 sqmm, over & including 15 mm thick screed bed in CM 1:4 in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match.

M&L for Vitrified Light Shade ceramic tiles 10 mm thick (Square/rectangular) area of each tile not exceeding 0.36 sqm , over & including 15 mm thick screed bed in CM 1:4 in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match.

M&L Glazed ceramic Digital tiles ,matt/glossy finish in vertical surface,in required combination of themes, area of each tiles exceeding 0.9 sqm but not exceeding 0.27 sqm 7-8 mm thick thick set and jointed in neat cement slurry, over 10mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

M&L double charged vitrified floor tiles in 600X600mm sizes (thickness to be specified by the manufacturer),in required combination of themes, with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in any colours and shades, over & including laid on 15 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc, complete all as spcfd & as directed.

M&L for Coloured Non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.16 sqmm, over & including 15 mm thick screed bed in CM 1:4 in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match for repair & matched to existing floor tiles in patches.

Cutting, polishing to existing Kota/ marble flooring,(three cuttings and mirror polishing) including levelling certain places to Kota/ marble floor & necessary repair work complete spcfd & as directed By Engineer-in-Charge at site

Cutting,Scrubbing,Rubbing, polishing toxisting Terrazo (Mosaic or Marble) flooring ) ,including removing mild water stains,organic spill stains ,scratches ,other marks & levelling certain places to Terrazo (Mosaic or Marble) floor ,including necessary repair work complete as specified & directed By Engineer-in-Charge at site

Demolition and breaking up drain pipes (SGSW, AC or reinforced cement) set in cement mortor internal dia of pipe 100mm complete all as spcfd & as directed .

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as spcfd & as directed .

Dismantling of cast iron drain pipes & fittings, jointed in cmenet mortor and taking out of trench required internal dia of pipe 75 to 100mm complete all as spcfd & as directed .

S&F 100mm bore cast iron soil waste and vent pipe (spun pipe) in any length with or without ears with cement joints fixed to walls/ceiling or laid in floor. complete all as spcfd & as directed .

-ditto- Item No 38 but 75mm dia complete all as spcfd & as directed .

S&F 100mm bore CI bends any radius complete all as spcfd & as directed .

All as per item No 40 above but 75mm bore complete all as spcfd & as directed .

S&F CI Cowls 100 mm dia bore complete all as spcfd & as directed .

S&F CI cowl 75 mm dia bore complete all as spcfd & as directed .

S&F CI Branch pieces single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches 100 mm dia bore complete all as spcfd & as directed .

S&F 110mm bore PVC (SWR) bends any radius complete all as spcfd & as directed .

M&L salt glazed stone ware gully traps 150x150mm , square mouth "P" type.

M&L cast iron Nahani trap 75mm out let dia meter with grating incluiding jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as spcfd & as directed .

S&F in repair brass CP shower rose 125mm size with or without swivel joints, including fixing to steel pipe or union complete all as spcfd & as directed .

S&F in repair vitreous china wash hand basin, white, of size 550x400mm flat back excluding taps, waste, chain and plug but including brackets, cutting for and pinning in ends of brackets or erecting stand complete complete all as spcfd & as directed .

S&F in repair bib tap, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15 mm bore, complete all as spcfd & as directed .

S&F in repair of pillar tap, cast copper alloy with capstan heads,chromium plated, fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore complete all as spcfd & as directed .

S&F in repair chromium plated15mm bore dia stop valve/Angle valve cast copper alloys, screwed down high pressure with crutch or butterfuly handle , screwed both ends for iron pipe or for unions and fixed complete all as spcfd & as directed ..

S&F waste fitting brass chromium plated for 32mm bore with long screwed shanks and fly nuts including 32mm PVC waste pipe for WHB complete all as specified and directed.

S&F MS chromium plated grating 125mm dia of weight not less than 50gm for floor trap / Nahani trap in repair complete all as spcfd & as directed .

S&F in repair of PVC low level flushing cistern 10 ltrs capacity with inlet ball valve float & handle, syphonic action type including brackets & flush pipe of polythelene of low or high level 32mm dia complete all as specified and directed .

S & F in repair of cast iron nahani trap of 75mm bore, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F in repair of 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, ISI marked complete all as spcfd & as directed .

S&F in repair of 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, ISI marked.

S&Fin repair of 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, ISI marked complete all as spcfd & as directed .

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as spcfd & as directed .

S&F rolled mild steel work as in post ,roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections,ms pipe) including distance pieces, cleats etc. conforming to Fe-410W Gde E-250 quality 'A' complete all as spcfd & as directed .

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil.

M&L of PCC 1:3:6 type C-2 ( 40 mm graded aggregates ) as in foundations filling and mass concrete complete all as spcfd & as directed .

Dismantling Asbestos cement (plain or corrugated, etc) sheets in roof coverings complete all as spcfd & as directed ..

M & L for Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as spfd & directed.

M&L for preparation of new untreated steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as spcfd & as directed .

M&L for one coats painting with synthetic enamel paint to old steel or steel based surfaces of any description, not otherwise described over 10 CM width or girth including preparation of surface including all preparatory work complete all as specified complete all as spcfd & as directed .

M&L 500 ltr ISI marked three layer rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position & including 20mm brass ball valve including taking down Complete all as specified & directed

M&L new 1000 ltr ISI marked rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position & including 20mm brass ball valve including taking down Complete all as specified & directed

Demolition of PCC in roof covering, kerbs, roof kerbs, benching, coved fillets etc including old decayed water proofing treatment of any type all as specified & as directed (also including the rate for disposal of building rubbish/ malba of dismantled or waste material collected after demolition of existing treatment & dumping for lead upto 1km for all lifts)

M&L for 40mm thick pcc 1:2:4 type B-1 using 20mm graded stone aggregate in roof covering , benching , etc & finished even and rough all as per directed complete all as specified & directed

M&L for screed bed or bedding layer of 15 mm thick cement mortar 1:4, for floor finished even & smooth without using extra cement complete all as specified & directed Note :- WPC shall be measured & paid seprately in respective item of BOQ

Supply only water proofing compound ISI marked complete all as specified & directed

S&F APP based polymeric membrane not less than 3mm thick, weighing not less than 3.5 Kg/sqm , reinforced with polyster non-woven fabric (weighing not less than 150 gm/sqm and upper side of membrane thermally insulated with white mineral gravel finish, informaly embadded during manufacturing process shall only be used. It shall be laid by torch application,side overlaps shall be 75mm and the ends shall be 100mm and all over laps shall be sealed by torch application including applying a coat of cold applied bitumen primer conforming to IS:[email protected]/sqm & applied a Hot blown coat of bitumen layer spread over primer @ 2.0 Kg/Sqm complete all as specified & directed

S&F in repair for PVC wall panelling with panel of 300 mm x 4 mm Hollow section of Sintex pattern SPUF- 146 or equivalent , fixed with PVC plug and screw and inserted to next panel groove, edges and corners of all door/ window/openings etc to be covered with PVC angel fixed with solvent cement complete all as specified as manufacturer's Instructions complete all as specified & directed

M&L for 15mm bore galvanised steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors including taking up & down the existing GI tubing

All as per Item No 76 above but 20mm bore

Taking up or down old serviceable 15mm bore GI pipe & Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, trenches etc ) including cleaning complete all as specified & as directed.

All as per Item No 78 above but 20mm bore

S & F in repair of vitreous china squatting pan, 'Orissa' pattern, size 580x440 mm white, with integral foot rests, 'P' or 'S' trap, including connection to trap, and to flushing pipe, anti-syphonage pipe etc. complete including making good to floor with PCC, Lime concrete bedding complete all as specified & as directed.

Taking down chowkats or frames n. exc 1.5 sqm each with shutters (without taking off shutters from the frame).

Taking down chowkats or frames exc 1.5 sqm but n exc 4 sqm each with shutters (without taking off shutters from the frame)

S & F powder coted Anodised Aluminium frame for door,windows,vantilators with one or more rebates including joining cleats for fixing etc complete all as specified complete all as specified & as directed .

S & F powder coated Aluminium door shutter,aluminium section weighing 0.55kg/m including necessary joining cleats glazing clips,rubber neoprene packing handles 2 Nos in each door,hinges anodized aluminium snap beading screw etc complete all as specified complete all as specified & as directed.

S&F powder coated Anodised aluminium window and ventilators shutters,side hung type without sash bars,aluminium section weighting 0.55 kg/m including necessary joining cleats,glazing clips,rubber packng,anodised aluminium snap beading,screws,anodised aluminium fitting such as peg stays 150mm long 1 nos ,hinges type B-21 100 mm long Nos suitable handle Nos complete all as specified complete all as specified & as directed .

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box,main body with stainless steel cover,governing pivot made of brass,other parts made of mild steel heavy duty and fixed complete all as specified & as directed.

S&F in repair Aluminium extruded section body door closer hydranlicelly regulated designation no 3 universal type suitable for door shutter up to 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified & as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation, boards/slabs/blankets, any thickness, including cover fillets and frame work complete all as specified & as directed .

M&L for providing and fixing Gypsum Board 8 to 10 mm thick in ceiling fixed with screws as per manufacturers instructions complete all as specified & as directed.

S&F anodised aluminium snap grid frame work of size 605x605mm for false ceiling complete all as specified & as directed.

S&F hangers 6mm dia. G.I (up to 1200 mm length ) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3mm size 60 mm long and hold fasterners 12.5mm dia 40mm long.complete all as specified & as directed.

S&F in repairs for Single piece-WC with UF Soft Close Slim Seat Cover, Fixing Accessories, Accessories set and Cistern Fittings, Size: 365x655x760 mm, S Trap-220mm complete all as specifies (Make;- Jaquar Registered design LYS-WHT-38851S220UFSMN or equivalent specified in Appx B)

Supply and fixing anodized snap grid frame work of size 605mm x 605 mm for false ceiling including necessary notching. The snap grid shall consist of anodized aluminium main & cross tee of size 36.5 x 25 x 1.4 mm weighing 0.24 Kg/RM and 23.5 x 26.4 x 1.40 mm weighing 0.191 Kg/RM respectively. The main and cross tee shall be jointed at junction crossing with anodized aluminum angle bracket of size 15mm x 15mm x 1.5 mm weighing 0.12 Kg/RM fixed with suitable MS bolts, nuts and washer. The snap grid (main/cross tee section) shall be supported at ends all along the wall with anodized aluminum angle of size 40 x 25 x 2 mm weighing 0.36 Kg/RM fixed to wall with suitable arrangement and providing 8-10 mm thick mineral fibre board of make Armstrong in fixed in grid support with 6.0 mm dia plain mild steel wire galvanised class 3 fixed in detached works etc to support snap grid, made of aluminum as per specification complete all as specified and as directed by Engineer-in-Charge.

M/S MAMTA CONSTRUCTIONS

M/s Gupta Traders

B R ENTERPRISES

VASUNDHARA AND COMPANY

M/s Ranaji Construction Co

Swastik Engineering Works

AMIT RISHABH BUILDERS PRIVATE LIMITED