SPL REPAIR TO BLDG NO P 113 JCOS MESS AND DRAINAGE NEAR BLDG NO P 96 P -97 AND P 98 AT JASAI MIL STATION UNDER GE ARMY BARMER

Amount

M&L for dismantling of wall panneling and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified and directed.

S&F solid PVC wall lining consisting of 5mm thick plain colour PVC sheet incluseive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

M&L for 4 mm thick E-board Tile false ceiling with powder coated GI snap grid frame work complete all as specified and directed. include all necessary drilling, cutting making good and necessary arrangement to fix electrical item as under:- (a) 25x25x1.5 mm thick GI tee powder coated as main and cross runners suspended with 1.6mm dia GI wire suspenders with adjustable clamps and dash free fastners plugging in RCC slab placed @ 600mm centre to centre from perimeter wall. (b) 25x25x1.5 mm thick GI angle powder coated plugged @ 600mm center to center along perimeter of wall. (c) Fixing of 4mm thick E-board tiles of size 595x595 mm of approved texture, and finished complete with two coats of oil emusion distemper on ceiling of approved Tint/ Colour shade over a coat of Primer, complete all as specified and directed. NOTE: The complete ceiling work shall be done as per manufacturers instruction and directed.

M&L for taking down cement plaster on stone masonry/brick masonry incl racking out joints, hacking for key scrubbing down with water and direction.

M&L for 10 mm rendering in CM 1:6 on fair face of brick work or on concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for 05 mm rendering in CM 1:3 on fair face of ceiling or on concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm rendering in CM 1:4 on fair face of wall or on concrete surfaces finished even and fair with water proofing compound (WPC) complete all as specified and directed. (WPC will be measured and paid seprately)

Supply only liquid water proofing compound (For external new plaster surfaces).

M&L for preparation of new plastered surface of wall and applying two coat of oil emulsion distemper of approved tints over a coat of interior wall primer complete all as specified and directed.

M&L for preparing new plastered surface of ceiling and applying three coat of white wash on ceiling complete all as specified and directed.

M&L for preparation of old plastered surface of wall and applying one coat of oil emulsion distemper of approved tints complete all as specified and directed.

M&L for preparation of old surfaces of ceiling (plastered or unplastered) by brooming or steel wire brushing, scrapping down smoke spot moulds, moss efflorescent salts and trading oil greasy spot and applying one coat of white wash on ceiling complete all as specified and directed.

M&L for complete removal of existing treatment incl preparation of wall surfaces and applying two or more coats of 100% premium acrylic emulsion paint of required shade, , having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm, over application of wall care putty average thickness 2 mm thick at any location on old plastered or unplastered surfaces of walls including necessary scaffolding arrangement as required at site complete all as specified and directed.

M&L for preparation of old decorated wooden surfaces of any description, not otherwise described over 10cm width & girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old decorated steel surfaces of any description, not otherwise described over 10 Cm width & girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for taking down chowkat or frames with shutters (without taking off shutters from the frames) area not exc1.5 Sqm each and removing from site complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube and fixing in opening complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consistiing of frame made out of MS tubes for top and bottom rail MS frame, shall be covered with heat moulded channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side and as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fited in the MS frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement complete all as specified and directed.

S&F 100mm size SS butt hinges and fixed to PVC frame /wooden frame and angle iron frame by necessary welding complete all as specified and directed.

S&F extruded aluminum alloy handle fabricated type anodized, 150mm size complete all as specified and directed.

S&F aluminum anodized barrel tower bolts extruded section, 150mm size complete all as specified and directed.

M&L for taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each complete all as specified and directed.

S&F second class hard wood 35mm gauged and skeleton shutter factory made without sash bars open rebated and prepared to receive gauge etc. top, bottom and lock rail, styles, edges of framing champhered or rounded fitted with cut and mitered wooden beads for securing glass etc; size of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F in repair stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staples or with wooden beads, stainless steel screws and nuts bolts etc complete all as specified and directed.

S&F factory made second class hard wood plain framed panelled shutter (two panel) with lock rail and pannel of 9mm thicks BWP commercial ply or 12mm veneered parlide board with commercial vereered on both faces the size of rails and style as per IS-1003 (Part-I) kiln seasond and chemicadly pressue treated 35mm thick complete all as specified and directed.

S&F 200 mm long aluminium barrel tower bolts stove enamelled black, with bright bolt and fixed complete all as specified and directed.

S&F 300 mm long aluminium sliding door bolt, anodised, with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F 140 mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F for mild steel ordinary rat tail rod pattern spring 300mm size including roller & roller plate and incl welding complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description, over 10cm in width or girth, not otherwise specified with two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for taking down aluminium door/ windows incl frames and complete fittings of area exc 1.50 sqm but n. exc 4 sqm complete all as specified and directed.

S&F powder coated 50 microns extruded aluminium glazing/ doors & shutters made out of section 63.5x38.10x1.29mm for chowkats or frame & shutters made of size 44.45x44.45x1.29mm for side rails and middle rail, 114.3X44.45X1.29mm for top rails and bottom rails and including 12mm thick high density fibre board pre-laminated on both sides (water proof) below middle/lock rail and 5mm thick tinted glass above middle/lock rail and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beads 20mm size with and incl mortice lock with duplicate keys etc complete all as specified and directed approved by accepting officer including supply and fixing the following items: (a) stainless Steel (304 Grade) finished Butt Hinges 150mm - 3 nos per leaf. (b) powder coated aluminium Tower Bolt 200mm long - 2 nos per leaf (c) powder coated aluminium Handles 150 mm - 2 nos per leaf

Providing and fixing factory made aluminium casement windows with 50 micron powder coating doubled panelled and double shutters consisting of frame and mullion of 101.60 x 44.45 x 1.29 mm and shutters made of 63.5 x 31.75 x 1.29 mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36 mm dia and 1.40 mm aperature in inner shutters complete fixed in all respect as specified including supply and fixing following items : (a) stainless Steel (304 Grade) finished Butt Hinges 125mm - 2 nos per leaf (b) powder coated aluminium Tower Bolt 150mm long - 2 nos per leaf (c) powder coated aluminium Handles 150 mm - 2 nos per leaf

M&L for repairing of RCC roof projection, chajjas, roof facia, column etc by necessary preparation i.e chipping, scrapping, cutting, chiseling avg thickness 50mm and cleaning exposed reinfocred surfaces of damaged, loosed RCC surfaces and applying rust remover on (CICO Clean-o rust) in two coats over rusted reinforcement surface of RCC members and providing anti corrosive coating with two component epoxy based zinc rich primer/Rust passivation Inhibitor coat at the rate of 2-3 sq. mtr/Ltr not less than 50 microns dft with CICO ZINCILATE-500 or equivalent to reinforcement surface as per manufacturer’s instructions including all machinery, tools tackles and clearing of debris. and apply one coat of cement slurry and filling the surfaces with cement concrete (1:1.5:3) using 12.5 mm graded stone aggregate and reinforced with welded XPM mesh of weight RCC using coarse sand in patches areas including plastering 10 mm thick with 1:4 cement mortar and apply two coat of cement base paint over a one coat of cement primer complete all as specified and directed. NOTE:Cost of formwork and welded mesh including scoffolding shall be deemed to be included in the quoted rate.

S&F for rotational moulded polyethylene water storage tanks of 500 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete all as specified and directed.

S&F in repair stainless steel tubing curtain rod of 20 mm dia chromium plated with 02 Nos stainless steel bracket fancy type, stops fixed with SS screws etc complete all as specified & directed. Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered as approved by accepting officer.

S&F in repair 15mm bore tubes medium grade galvanized with all fittings such as tee, elbows, sockets, unions, plugs, short lenghts etc. and fixed complete to walls and ceilings or laid in floors concealed or open of any length complete all as specified and directed.

S&F in repair 20 mm bore tubes medium grade galvanized with all fitting such as tee, elbows, sockets, unions, plugs, short lenghts etc and fixed complete to walls and ceilings or laid in floors of any length complete all as specified and directed.

S&F in repair 15 mm dia bib tap, fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and directed.

S&F in repair 15mm bore CP fancy type stop valves/angle cock, cast copper alloy, screwed both ends for iron pipe or for union complete all as specified and directed.

S&F in repairs 15mm dia bib tap (2 in 1 type) of brass, chromium plated fancy type glossy finish complete all as specified and directed.

S&F in repair 15mm bore pillar tap cast copper alloy fancy type with capston heads, chromium plated screwed down high pressure, with or without letters hot or cold with long screwed shanks and fly nuts, screwed for iron pipes and fixed complete all as specified and directed.

S&F in repair brass CP wall mixer 2 in 1 with provision for overhead suitable for 15mm bore pipe complete all as specified and directed.

S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F in repairs chromium plated swivel shower roses with or without swivel joints, for fixing with 15mm pipe fixed complete all as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repairs tubular towel rail, brass cromium plated, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F in repair aluminium door closer hydraulically aluminium die cast body regulated designation No. 2 universal type (ISI Make) suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 Kg complete all as specified and directed.

S&F in repair PVC connection 15mm bore length not less than 450 mm long with both ends PTMT nuts complete all as specified and directed.

S&F in repairs 32/40 mm bore waste fittings, brass, chromium plated for sinks, basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in repair 110mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on trenches or in floors /wall complete all as specified and directed.

S&F in repair 75mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on trenches or in floors/wall complete all as specified and directed.

S&F in repairs 75mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair PVC (SWR) bend any radius 110mm complete all as specified and directed.

S&F in repair PVC (SWR) bend any radius 75mm complete all as specified and directed.

S&F in repairs 110 mm bore PVC [SWR] Junction single [single "T" or "Y"] equal or unequal, complete all as specified and directed.

S&F in repairs 75 mm bore PVC [SWR] Junction single [single "T" or "Y"] equal or unequal, complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan pedestal pattern white including connection in drain and in flushing pipe complete including 'P' or 'S' trap and including plastic water closet seat cover with flat bottom and cover with MS chromium plated hinge divice ISI marked complete all as specified and directed.

S&F in repair vitreous china squatting pan of Orissa patten size 580 x 440 white colour including CI S/P trap long size directed. joint run and lead front or back inlet with integral foot rest including connection to trap and to flushing pipe, anti-syphonage pipe, etc and making good to floor in PCC 1:2:4 complete all as specified and directed.

S&F in repair vitreous china premium/1st quality urinal half stall type, white colour, of size 465x355x265 mm incl providing and fixing plugs/brackets, bedding urinal against wall in CM 1:2, securing urinals to plugs with and incl all accessories for fixing as recommended by manufacturer like 60mm long brass secrews/fasteners/rag bolts etc, pointing urinal back in white cement; connecting for discharge pipe incl necessary packing, union complete all as specified and directed.

S&F in repair urinal spreader of PTMT any colour for fixing with 15mm dia pipe complete all as specified and directed. (Minimum weight 60gms).

S&F in repair vitreous china premium/1st quality wash basin (under counter), white, size 550x400 mm including all accessories as recommended by manufacturer complete fixed in position in all respect as per manufacturer's instructions and all as specified including all Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in repair flushing cistern of PVC 10 ltr. cap. with dual flushing system, valveless syphonic action type, low level, white/ivory/off white with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing complete all as specified and directed.

S&F in repair grating doom 125mm dia with waste hole of PTMT (minimum weight 40 gms) complete all as specified and directed.

S&F in repairs sinks with drainage board made of stainless steel 1mm thick with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

M&L for demolition of reinforced cement concrete on roofs, floors (other than ground floors), beams, staircase, landing, chajjas and similar suspended work complete all as specified and directed.

M&L for nominal mix reinforced cement concrete type B1 (1:2:4) using 20 mm graeded stone aggregate as in roof slabs supported on walls surfaces of concrete flat complete all as specified and directed.

M&L form work to edges of concrete flates, treads break in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sisides of RCC/PCC bands in walls, horizontal or sloping and ssimilar work exc 10 cm but n. exc 20 cm wide rough finished surface of concrete complete all as specified and directed.

M&L for TMT bars 10 mm and over cut to length, bent to shape required incl cranking, bending spirally for hoping for columns hooking ends and bindind with ms wire (annealed) not less than 0.9mm dia quality confirming complete all as specified and directed. (GRADE FE-410-W, Gde.E-250 quality-A )

M&L for demolition of stone / boulder masonry walling built in cement mortar including all quoins arches pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and as directed.

M&L for precast-cement concrete block masonary with solid blocks type D-1, 1:3:6 (20mm graded aggregates) exc 10 cm in width and setting in CM 1:4, complete all as specified and directed.

M&L for dismantling of plain or corrugated steel sheets in roof coverings any type complete all as specified & directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.5 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping crews as specified complete all as specified and directed.

M&L for dismantling structural steel work including doors gates but excluding framed truss etc complete all as specified and directed.

S&F for hollow, rolled sections as in main and cross beams, column, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conf to Fe-410-w or E -250 quality A complete all as specified and directed.

S&F in repair plain (white) PVC celuka ply board in door, shelves for cup boards or kitchen cabinets, one side laminated, one side plain 18/19mm thick as reqd, jointed by means of PVC adhesive Solvent and fixed using self tapping SS screws complete all as specified and directed.

S&F stainless steel silver chrome door handle 100mm long, suitable for fixing of brass screws inside of the board etc and fixed in repairs complete all as specified and directed.

S&F magnetic door catcher medium grade to hold approx 1000 mm opening cabinet door and fixed in repairs complete all as specified and directed.

S&F stainless steel frog hinges suitable for kitchen cupboards 22mm PVC celuka board etc for smooth movement and fixed in repairs, complete all as specified and directed.

M&L for dismantling floor, hearth or wall tiling including cement mortar bedding, removing serviceable tiles to stores and removing debris outside the MD land complete all as specified and directed.

M&L for 300mmx300mmx10mm thick non skid polka dots parking floor paver tiles with grey cement and pigment, over and including 15mm thick screed in CM (1:4), set jointed & pointed in neat cement slurry in floors complete all as specified and directed.

S&F non-skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

S&F vitrified ceramic tiles in light shade 10mm thick (square/ractangular) polished, area of each tiles not exc 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per srl item no 85 above but as in skirting over 15mm thick cement mortar backing plaster in CM 1:4 complete all as specified and directed.

M&L for glazed ceramic glossy finish tiles coloured in vertical surface 450X300X7mm in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed.

M&L for demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and directed. Note : Work will be in patches or in bulk.

M&L for machine cut kota stone slab flooring 20-25mm thick over, laid over cement screed base, jointed and pointed with grey cement slurry mixed with pigment over 20mm thick cement mortar 1:6 screed bed to match the shade of the slab including rubbing and polishing complete all as specified and directed. Note : Work will be in patches or in bulk

M&L for machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar over 10 mm thick cement plaster 1:3 jointed and pointed with grey cement slurry mxed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for granite of black / green / imperial red (colour as approved by accepting officer) of any type machine cut as in shelves/steps/counter tops, 20 mm thick, set and jointed in cement slurry over & including screed of 15 mm thick / rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab or with suitable adhesive for fixing on unpolished kota stone slabs and including rubbing, cutting and mirror type polishing and bull nose on exposed sides complete all as specified and directed. Note : Single piece should be used in steps/cills/jambs/shelves or equivalent as approved by accepting officer .

M&L for demolition of concrete in ground floors and paving n exc 15cm thickness (below or above ground level) complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in subbase of floor and finishing the surface even & smooth without using extra cement complete all as specified and directed.

M&L for 100mm thick cement concrete type D-2, 1:4:8 (40mm graded crushed stone aggregate) finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

M&L for demolition for (RCC jhali) ashlar facings, dressed stonework, precast concrete articles and precast concrete block walling complete all as specified and directed.

M&L for providing precast cement concrete louvres and jallies of type B0 1:2:4 (12.5mm graded aggregate) set in cement mortar 1:4, of 40mm thick (measured solid), including all mouldings but excluding frame complete all as specified and directed.

M&L for demolition of cement concrete (reinforeced) in floors and paving n.exc 15cm thickness (above or below ground level) complete all as specified and directed.

M&L for walling random rubble masonry uncoursed well bonded bedded and solidly hearted and built in cement mortar 1:4 etc complete all as specified and directed.

All as per srl item No 98 above but except stone.

M&L for extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, with maximum depression on face from straight edge held against the dressed surface n exc. 20 mm of random rubble walling of sand stone, uncoursed or brought upto courses complete all as specified and directed.

M&L for 15mm thick rendering on stone masonry surface ,in (CM 1:4,) finished fair and even without using extra cement including neeru finish to plastering complete all as specified and directed.

M&L for PCC 1:2:4 (Nominal mix) type B-1 using 20mm graded aggregate as in surface channel and drain complete all as specified and directed.

M&L for cement concrete type D-2, 1:4:8(40 mm graded aggregate), 100 mm thick, complete all as specified and directed.

M&L for extra for forming fair finished drain or channel 30cm inner girth cement concrete using extra cement including forms, moulds metred/stopped ends etc complete all as specified and directed.

M&L for PCC (1:2:4) Type B-1 (using 20mm graded crushed stone agg.) as in copping rounded or chamfered on edges in any description complete all as specified and directed.

S&F steel reinforcement of TMT bars of size 8mm dia and over, cut to length, bent to shape as required including cranking, hooking ends & binding with mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed.

M&L for precast reinforced (perforated) cement concrete M-15 (1:2:4) nominal mix type B-I, (Using 20mm grade stone agg) set in cement mortar 1:4 as in manhole/rain cover incl all neceaasary form works etc complete all as specified and directed.

M&L for rolled mild steel work frame work such as in grills gratings, cooler stands, staging for water tank etc ends of bars shouldered and or riveted or forged into spike framed guard bars barred iron doors ladders frame laluster, walk ways, railings frameworks of water tanks and similar work conforming to Fe 290. Gde E165 including necessary fixing to walls complete all as specified and directed.

m/s jogaram sujaram (BID ID -3187412)

m/s sai construction company,bijarar (BID ID -3188752)

Paliwal Construction Company (BID ID -3189005)

National Rewinding Works (BID ID -3189095)

M/S Tanisha Traders (BID ID -3185016)

Lalit and Brothers (BID ID -3188511)

Devi Engineeing (BID ID -3188536)

S.K. INFRASTRUCTURE (BID ID -3188650)

M/s Malinath Electricals (BID ID -3189339)