SPECIAL REPAIR TO BLDG NO T 10 AT JAKLI RTC DHANSAL

Amount

Demolition of Brickwork or stone/ boulder masonry, built in Cement mortar including all quoins, arches, pillars, etc, but including ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed .

M&L for Brickwork with subclass 'B' bricks (old size bricks), straight or curved on lan exc 6m mean radius, built in Cement Sand Mortar 1:6 complete all as directed.

Brickwork with sub class ‘B’ (except bricks) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified.

M & L old size brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

M & L for rendering 15 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces with using integral waterproofing compound including finishing the surface even and smooth without using extra cement complete all as specified. (supply only of W P C shall be measured and paid separately).

M & L for rendering 15 mm thick in cement and sand mortar 1:6 on other than fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and as directed

M & L for rendering 5 mm thick in cement and sand mortar 1:4 on concrete surfaces of ceiling including finishing the surface even and smooth without using extra cement complete all as specified and as directed.

Supply only integral waterproofing compound complete all as specified and directed

Preparation of newly plastered surfaces of walls and applying two coats of cement base pain tover a coat of primer complete all as specified.

Preparation of newly plastered surfaces of ceiling and applying two coats of white wash complete all as specified.

Preparation of newly plastered surfaces of walls and applying three coats of distemper oil emulsion complete all as specified.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level ) complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off premises complete all as specified.

M & L for 75 mm thick PCC 1:3:6, type C-2 using 20mm graded stone aggregates as in sub base of floor, finished even and fair, complete all as specified and directed.

M&L for 100mm thick PCC 1:2:4, nominal mix, type B2, using 40mm graded crushed stone aggregate as in plinth protection, laid in alternate bays (not exceeding 2 Sqm each) surface finished even and fair without using extra cement and providing joints throughout the thickness of plinth protection, filled with mastic filling comprising of one part of bitumen 85/25 grade and three parts of sand by weight, complete all as specified

M & L for Non skid coloured joint free ceramic tiles 300x300 and 6-7mm thick in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 15 mm thick screed bed in cement and sand mortar 1:4, complete all as specified.

M & L for Glazed ceramic tile 350x 250x 7 mm/ 450X 350X 7mm thick (coloured) on vertical surfaces such as skirting, dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10 mm thick plaster in cement and sand mortar 1:4 complete all as specified.

M & L for Virified Ceramic tiles 10 mm thick with dark shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over and including 20 mm thick screed bed in cement and sand mortar 1:4, complete all as specified

Dismantling wrought iron or mild steel work of any description not other wise provided for.

Dismantling of plain & corrugated steel sheeting any gauge, thickness including Nanital or similar pattern roof covering like ridges, hips, valleys and flashings etc complete all as specified.

Rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or incl butt welded tubes conforming to IS 1161-1998 grade St-240 and painted one shop coat of zinc chromate promer paint (incl preparation of surface) at contractor's workshop before fabrication complete all as specifed and directed.

Mild steel rolled section as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) incl distance pieces, cleats etc. confirming to grade Fe-290. Gde- E-165. complete all as specifed and directed.

S&F pre-painted galvalum aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour tensile strength of 550mpa as in roof covering/cladding to wall, fixed with self tapping screws as a specified.

S&F pre-painted galvalum aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550mpa as in roof covering/cladding to wall, fixed with self tapping screws as a specified.

Dismantling of wall and ceiling board (fibre, pulp insulation etc) for insulation board/slab/blankets any thickness incl cover fillet.

Aluminium anodised snap grid frame work of size 605 x 605 mm for false ceiling including necessary notching. The snap grid shall consist of aluminium anodised main and cross tee of size 36.5 x 25 x 1.4 mm weighing 0.24 Kg/Rm and 23.5 x 26.4 x 1.4 mm weighing 0.191 Kg/Rm respectively. The main and cross tee shall be jointed at junction crossing with aluminium anodized angle bracket of size 15 x 15 x1.5 mm weighing 0.12 Kg/Rm fixed with suitable MS bolts, nuts and washers. The snap grid (main/cross tee section) shall be supported at ends all along the wall with aluminium anodized angle of size 40 x 25 x 2 mm weighing 0.36 Kg/Rm fixed to wall with suitable arrangement and providing 4 mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size n. exc 1.5 Sqm each and removing from site complete all as specified.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exceeding 1.5 sqm and not exceeding 4.00 sqm each and removing from site complete all as specified.

Pressed steel frame for doors of size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including one shop coat of priming complete all as specified.

PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate as in filling of pressed steel frame complete all as specified.

PCC 1:3:6 type C-1 using 20mm graded stone aggregate for hold fast blocks, including necessary form work for rough finished surfaces etc complete all as specified.

35mm thick, 2nd class hard wood plain, framed, panelled factory made shutters (two panel) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified.

35 mm thick, 2nd class hard wood , glazed & skeleton factory made shutters, open rebated & prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metred beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.20(a) complete all as specified.

Painting to new wood or wood based surfaces of any description not otherwise described over 10 cm in width or girth including preparation of surfaces, priming with pink primer (one coat) finished with two coats of synthetic enamel paint complete all as specified.

Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as shown in drawing of relevant item in MES, schedule Part-II , 2004 as specified.

S & F Factory Made Solid PVC Moulded Door Shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed

S & F Mild steel framed work as in grills, grating etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, conforming to Fe-290. Gde- E-165. complete all as specified.

S & F for factory made steel windows with side hung shutters including projecting type hinges with steel handle & steel peg stay complete with glazing bars, dovetailed or welded and also including painting the exposed steel surfaces with one shop coat of Zinc-Chromate primer complete all as specified and as directed.

S & F for factory made steel windows with side hung shutters including projecting type hinges with steel handle & steel peg stay complete without glazing bars, dovetailed or welded and also including painting the exposed steel surfaces with one shop coat of Zinc-Chromate primer complete all as specified and as directed.

S & F for steel ventilators with top hung shutters including hinges, steel peg stay complete all as specified and as directed.

M & L for preparation of new steel surfaces of any description exc 10 cm width or girth, priming with red oxide primer and painting with two coats of synthetic enamel paint complete all as specified and directed.

S & F for Butt hinges, 100 mm long medium weight, cold rolled mild steel, ISI marked complete all as specified.

S & F for 300 mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete all as specified.

S & F for 200mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified.

S & F for 150mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified.

S & F for aluminium handles cast type anodised of size 150mm long ISI marked complete all as specified.

S & F for 300 mm size mild steel ordinary rat tail rod pattern springs including roller and roller plate, ISI marked complete all as specified.

S & F Galvanized mild steel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified.

03 mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified.

03 mm thick figured (frosted) glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified.

Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etc including cleaning for refixing or removal complete all as specified.

15mm bore tubes, medium grade, galvanised with and including all fittings fixed to walls, floors, or ceiling or laid in floors etc complete all as specified.

M & L for dismantling of water tank of capacity exc 500 and not exc. 1000 litres and removing to store and supply and fixing of 1000 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top & FDA approved, tripple layer body, 100% UA stablised, rust proof) hoisted and fixed in position all as specified in SSR Part-I, complete, all as specified and as directed. Note : Water storage tank shall be White with screwed lid

Use and waste form work to sides and soffits of floor or roof beams, beams haunching, girders, bressummers, lintels, cantilevers, shelves including supports, over hangs, etc. also splays between floors and beams etc for flat rough finished surfaces of concrete complete all as specified and directed.

Use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exceeding 200 mm thick (Horizontal or slopping) for flat rough finished surfaces of concrete complete all as specified and directed.

Use and waste form work to chullah hoods, chajjas, troughs and similar items including edges for flat rough finished surfaces of concrete complete all as specified and directed.

M & L mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L mild steel TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for Reinforced Cement Concrete (nominal Mix) M-25 (20 mm graded aggregates) as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and directed

M & L for Reinforced Cement Concrete (nominal Mix) M-25 (20 mm graded aggregates) as in Chajjas complete all as specified and directed

M & L for Reinforced Cement Concrete (nominal Mix) M-25 (20 mm graded aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

M & L for rendering 10 mm thick in cement and sand mortar 1:3 on cement concrete surfaces with using integral waterproofing compound including finishing the surface even and smooth without using extra cement complete all as specified. (supply only of W P C shall be measured and paid separately).

M & L applying evently a tack coat of industrial bitumen 85/25 at the rate of 12kg per 10 Sqm incl cleaning surface complete all as specified.

M & L for 25 mm thick Cement concrete type B-0, 1:2:4 (12.5 mm graded aggregate) as a padding on roof slab complete all as specified and directed.

M & L for APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms/sqm) incl priming surfaces and applying normal treatment (for moderate conditions) using glass fibre base bitumen felt, grade 2 primed surface by forced application complete all as specified and directed

S & F Tubular towel rail aluminium anodised 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls, complete all as specified.

S&F grating round 125mm size of PTMT fixed with cement motar.(Min weight 40 gms)

S & F Gate valves, with iron wheel head, screwed both ends for bore of 15 mm pipe and supply and fixed in repairs.

S & F 20 mm bore dia of pipe ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (Min weight 210 gms) of approved make complete all as specified and directed

S & F in bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule for 15 mm bore pipe complete all as specified & directed.

S & F stop valve, 15 mm bore dia cast copper alloy, fancy type, chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified & directed.

S & F PVC connection 15 mm size with PTMT nuts of length 600 mm long complete all as specified and directed.

S & F 15 mm dia pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed

S & F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms)

S & F for Vitreous China squatting pan “Orissa pattern” size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) with CI ‘P’ trap of long arm of suitable size including connection to flush pipe, anti symphonic pipes etc fixed in repairs, complete all as specified.

S & F for PVC low level flushing cistern, valveless, syphonic action type, 10 litres capacity with inlet, ball valve float and handle with and including brackets & PVC bend pipe 90 cm long etc, supplied and fixed in repairs, complete all as specified.

S & F Flush pipe of polyethylene of low or high density, 32 mm dia for low level cistern including taking down old pipe, complete all as specified.

S & F Vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe fixed in repairs (excluding flushing cistern, flush pipe and waste pipe) all as specified.

S & F Vitreous china wash basin, white, flat back, size 630x450mm including pillar tap, waste fitting chromium plated brass, chromium plated steel chain and rubber plug, porcelain stopper, a pair of CI brackets, waste pipe and pillar tap etc., fixed in repairs complete all as specified.

S & F 15 mm swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms) complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required

S & F 100 mm spun cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

S & F 75 mm spun cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

S & F 75 mm bore of pipe cast iron cowls complete all as specified and directed

S/F 75mm cast iron soil, wast and vent pipes in any length with or without ears with cement joints fixed to wall complete all as specified and directed.

S & F 100 mm bore of pipe cast iron cowls complete all as specified and directed

S/F 100 mm cast iron soil, wast and vent pipes in any length with or without ears with cement joints fixed to wall complete all as specified and directed.

S & F 75 mm bore of cast iron pipe branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

M & L for Salt-glazed stoneware gully traps, square or round mouthed, tvpe 'P' of size 150mmx100mm including setting and jointing to drain pipe in CM 1:1 complete all as specified and directed.

M & L for dia. Of outlet 75 mm Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) using 20 mm graded crushed stone aggregate with cement joint, complete all as specified and directed

S & F 75 mm bore of cast iron pipe bends (any radius), diminishing pieces or tapers complete all as specified and directed.

M & L for laying broken stone or boulders hardcore of guage not exc 63 mm deposited spread and levelled in layers not exc 15 cm thick watered rammed and consolidated to a true surface complete all as specified and directed

Use and waste form work for flat fair finished surface to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc vertical or to batter complete all as specified and directed.

M & L for cement concrete 1 : 3 : 6 type C-2 using 20 mm graded stone aggregate as in benching/surface channels etc complete all as specified and directed.

Earth work in excavation by mechanical means (Hydraulic excavator)/ infoundation trenches ordrains (not exceeding 1.5 min width or 10 sqm onplan), including dreessingof sides and ramming ofbottoms, lift upto 1.5 m,including getting out the excavated soil and disposal of surplus excavated soil asdirected, within a lead of 50 m. in any type of soil all as specified & as directed.

M & L for cement concrete 1 : 4 : 8 type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete etc complete all as specified and directed.

M & L for brickwork in cement mortar 1:4 with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius for manholes etc complete all as specified and directed

M & L for cement concrete 1 : 3 : 6 type C-2 using 40 mm graded stone aggregate as in benching/surface channels etc complete all as specified and directed.

M & L rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement mixed with WPC (as per manufacturer's instructions) complete all as specified and directed. Note : WPC shall be measured and paid separately

M & L mild steel TMT bars 6 mm to 8 mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for providing precast cement concrete type B1, 1 : 2 : 4 (20 mm graded aggregate) as in cover slabs (for man holes etc) and similar articles with plain faces set in cement mortar 1:4 complete all as specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed

M & L concrete bed to drain pipes including forming cradles in cement concrete 1:4:8 type D-2 for 150 mm bore of pipe complete all as specified and directed

S & F reinforced concrete pipes 150 mm dia bore, class NP2, laid and jointed complete with collars etc all as specified and directed.

Taking down old unserviceable/deteriorated batten/PVC conduit point wiring aluminium/ copper from existing place i.e. light, fan, socket or power points complete with all unserviceable fittings such as switches, sockets,bell push , ceiling rose, pendants, Holders, etc and making good all disturbed surface to wall, floor etc by means of cement mortar (1 : 3) or plaster of Paris and to match / finish new surface as the existing surface either by using same colour distemper, Putti or white / colour wash all as required and directed by Engineer-in-Charge.

M & L for concealed point wiring on wall and ceiling/roof with necessary fixing arrangements with PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade drawn in and including rigid non metallic white / ivory PVC conduit medium grade ISI marked not less than 20 mm dia with all conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.6 mm with earth dolly and Bakelite laminated sheet 3mm thick ISI marked for fixing of switches / sockets, fan regulators, wall mounting fittings, door bell & bulkhead etc with MS screw and cup washers including PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade for continuous earthing including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of paris/Putti or distemper / colour wash with same existing colour surfaces all as specified and directed by Engineer-in-Charge for the following:-

For One light /Fan/Bell point controlled by one switch 6/5 Amp one way single pole.

For One 3 pin socket outlet 6/5 Amps controlled by one switch on the same board with other switches.

For One 3 pin 6/5 Amp socket outlet controlled by one switch independent board.

All as per item No 108 here-in-before but for power point wiring with 2.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable and 1.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable as continuous earth lead.

S&F switch piano flush type (ISI marked), single pole, one way 6 Amp, 240 Volts complete all as specified and as directed.

S&F switch piano flush type (ISI marked), single pole, one way 16/15 Amps, 240 Volts including complete all as specified and as directed.

S&F socket outlet 3 pin, 6 Amp piano flush type including complete all as specified and as directed.

S&F socket outlet, 2 in 1, 3/5 pin 6 / 16 Amp, piano flush type complete all as specified and as directed

S&F ceiling rose, surface bakelite, 65mm x 50mm, two to three terminals complete all as specified and as directed.

S&F for batten angle lamp holder insulated body with back plate suitable for batten fittings including complete all as specified and as directed

Supply & Fixing medium step type fan regulator , 240 Volt AC, socket size, medium step" ISI marked complete all as specified and directed.

Supply & Fixing in replacement of old unserviceable DB by SPN Distribution Box, double door of protection grade IP 43 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type copper bus bar, Din rail, earth bar of 8 way, confirming to IS 13032 & 8623 complete all as specified and directed.incl Taking Down unsv MCB DB

Supply & Fixing in replacement DB by SPN Distribution Box, double door of protection grade IP 43 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type copper bus bar, Din rail, earth bar of 12 way, confirming to IS 13032 & 8623 complete all as specified and directed.

Supply & Fixing MCB SPN, 32 Amps 240 volts, AC , 10 KA breaking capacity 'C' Series,"ISI marked and conforming to IS 8828/IEC 60898-1 complete all as specified and directed.incl Taking Down unsv MCB

Supply & Fixing MCB SP, 06 to 32 Amps 240 volts, AC , 10 KA breaking capacity 'C' Series,"ISI marked and conforming to IS 8828/IEC 60898-1 complete all as specified and directed.incl Taking Down unsv MCB

S&F Wall mounted LED batten 18 Watt with 01 No LED tube rod, extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver including dismantling taking down unsv FTL fitting T8 type any type complete all as specified and directed.

Supply only LED lamp 12 watt, CDL, B-22 cap, (Pin type), 230V, PF-0.95 (min) incl dismentling taking out unsv CFL/LED Bulb. complete all as directed by engr-in-charge

M&L for earthing as per IS:3043 with galvanized steel earth plate electrode 600 x 600 x 6.0 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to galvanized iron wire 4 mm dia (8 SWG) as earthing lead protected by GI pipe medium grade 15 mm bore for protection of GI earth wire and 20 mm dia GI pipe medium grade for watering with alternate layers of charcoal /coke and salt including all accessories like nut, bolts, reducer, nipple, wire meshed/screened funnel and making brick masonry finished chamber of internal size 300 mm x 300 mm x 300 mm with concrete base, covered with PCC cover which shall be embedded in the block masonry including excavation works, refilling, connected to main switch/MCB DB for feeding the electric supply to domestic quarters compete all as specified as shown in electricall plateNo. 3 of SSR Part-I and testing of earth resistance as required including taking down unsv earthing .complete all as directed by engr-in-charge

Supply and fix ceiling fans, energy efficient, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor complete including traking old unsv ceiling fan and depositing to E/M store yard jindrah all as directed by engr-in-charge

M & L for sub main wiring with two run of FR PVC insulated unsheathed flexible copper conductor (Multistrands), single core of size 6.0 Sqmm, 1100 Volts grade and one run of 4.00 Sqmm FR PVC insulated unsheathed as earth (In Green Colour), flexible copper conductor (Multistrands) for continuous earthing conforming to IS 694 with latest amendments and drawing in PVC rigid conduit , connecting incoming / outgoing electric connections by using required size copper lugs / thimbles and making good the disturbed surface to match with existing complete in all respect all as specified and directed. Note :- 1. Two run of single core cable with one run of contineous earth wire of copper conductor wire Flexible (Multistrand) of FR PVC insulated and PVC conduit 25 mm dia including taking down old unsv wiring shall be measured and paid as one unit length

Surface excavation n.exc 30 cm deep and and avg 15 cm deep and getting out any type of soil complete all as specified.

Removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete.

M&L for 60mm thick factory made machine pressed precast concrete interlocking paver block any shape and size conforming to ISI 15658-2006 of M-35 grade, with grey cement and no pigment & laying over and including plain cement concrete 75mm thick of 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in levelling course for interlocking paver block and 25mm thick sand cushion incl watering and consolidation and joints filled with sand complete all as specified and directed.

M & L for cement concrete 1:2:4 type B1 using 20 mm graded aggregate as in coping for manhole and interlocking paver block incl weathering slightly rounded or chamferred angles including necessary formwork an dfinishinng the exposed surface complete all as specified and directed

devraj chalotra

M/S PAWAN KUMAR ANAND

M/S SANJAY STEEL WORKS