GE/KHU-T-49/2018-19 REPAIR/REPLACEMENT OF INTERNAL ELECTRIFICATION AND LT PANELS AT KHALTSI, LAMAYURU, BIAMAH, HANUTHANG AND ACHINATHANG UNDER GE KHUMBATHANG

Amount

Taking down carefully copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceilling roses, pendants , regulators, sockets light fitting etc for taking credit removing from site and making good disturbed surface etc.

M&L for point wiring with 1.5 sqmm cable FRLS, PVC insulated, unsheathed copper multistranded conductor, 1100 V grade including necessary termination board with 1.5 Sqmm PVC insulated unsheathed FRLS copper conductor cable as earth wire connected to common earthing drawn through PVC heavy duty casing caping/PVC conduit ISI marked as required at site along with all accessories and making good the disturbed surfaces of wall/ ceiling etc for the following : - Note : Colour coding for point and sub main wiring should be maintained at site. Incase of any deviation necessary recovery will be made as applicable. If any fitting is found serviceable and point wiring is unserviceable only point wiring will be replaced.

One light point/ one fan point/ Bell Point controlled by one switch

One 3 pin socket outlet, 5 Amp independent Board

One 3 pin socket outlet 5Amps on same board with other switches

All as per item No 05 above but for point wiring for power point with 2.5 Sqmm FRLS PVC insulated unsheathed copper cable 1100 Volt grade drawn through and including PVC casing caping heavy duty ISI marked as required alongwith accessories with 1.5 Sq mm FRLS PVC insulated unsheathed copper conductor cable as earthing wire and connected to common earth complete all as specified and directed.

S&F switch piano flush button type 5 Amp single pole one way (ISI marked) complete all as specified and directed.

S&F switch piano flush type 15 Amp single pole one way ISI marked complete all as specified and directed.

S&F socket out let multipurpose three pin 5 Amp and 2 pin 5 Amp flush type complete all as specified and directed.

S&F socket outlet 2 in 1, three pin 5 Amp and 6 pin 15 Amp flush type (multi purpose) ISI marked complete all as specified and directed.

S&F ceiling rose three terminal pvc/polycarbonate, isolated body complete all as specified and directed.

S&F lamp holder ,PVC/Polycarbonate type with back plate suitable for batten fitting (angle /plain) complete all as specified and directed.

S&F in repair 9 watt, 230 Volts, 50 Hz LED tube light fitting, wall mounted, decorative ultra slim square profile linear with extruded, polycarbonate, environmental friendly, energy efficient type, 4 feet long, channel type bracket including 18 watt LED tube rod inclusive of necessary connection prewired and making connection with 3 core PVC copper flexible cable of 1.5 sqmm size with nearest ceiling rose complete all as specified and directed. Make : Havells Cat Part No LUMILINEBS9WLED830SPCWH or equivalent

S&F in repair 18 watt, 230 Volts, 50 Hz LED tube light fitting, wall mounted, decorative ultra slim square profile linear with extruded, polycarbonate, environmental friendly, energy efficient type, 4 feet long, channel type bracket including 18 watt LED tube rod inclusive of necessary connection prewired and making connection with 3 core PVC copper flexible cable of 1.5 sqmm size with nearest ceiling rose complete all as specified and directed. Make : Havells Cat Part No lumilineBS18WLED830SPCWH or equivalent

S&F 42 W LED ultra modular designed architectural LED luminaire suitable for recess/ armstrong celling/ grid ceiling and POP mounting complete incl making necessary connection with 3 core PVC copper flexible cable of 1.5 sqmm size complete all as specified and directed Make: cat part No. LHEWDRP6PK1W042 of Havells or equivalent in Philips/crompton Greaves

S&F 36 W LED ultra modular designed architectural LED luminaire suitable for recess/ armstrong celling/ grid ceiling and POP mounting complete incl making necessary connection with 3 core PVC copper flexible cable of 1.5 sqmm size complete all as specified and directed. Make: cat part No. LHEWBPP7PL1W036 of Havells or equivalent in Philips/crompton Greaves

S&F in repair piano Switch flush button type 5 Amp single pole one way (ISI marked) complete all as specified and directed.

S&F in repair switch piano flush type 15 Amp single pole one way ISI marked complete all as specified and directed.

S&F in repair socket out let multipurpose three pin 5 Amp and 2 pin 5 Amp flush type complete all as specified and directed.

S&F in repair socket outlet 2 in 1, three pin 5 Amp and 6 pin 15 Amp flush type (multi purpose) ISI marked complete all as specified and directed.

S&F in repair lamp holder ,PVC/Polycarbonate type with back plate suitable for batten fitting (angle /plain) complete all as specified and directed.

S&F in repair compact electronic ballast suitable for any type fluorescent tube/CFL light fitting of 40/36 watt complete all as specified and directed.

S&F in repair LED Lamp 7 Watts complete all as specified and directed. Make: Havells /Philips/ Syska /CG

S&F in repair LED Lamp 10 Watts complete all as specified and directed.Make: Havells /Philips /Syska/CG

S&F in repair casing and caping 25mm/PVC heavy duty conduit including all fixing accessories complete all as specified and directed.

S&F in repair tube rod of 36/40 watt suitable for 36/40 watt tubelight fittings complete all as specified and directed.

S & F in repair plastic laminated bakalite sheet 3mm thick, ISI marked, incl drilling / cutting for housing of required No. of switches/sockets as required at site, incl cadmium plated MS screwes for fixing of sheet to existing MS sunken boxes complete for following sizes:-

S&F in repair box type switch socket combined 2 in 1, 5/6 Amp with plastic box (multi purpose) ISI marked complete all as specified and directed.

S&F in repair box type switch socket combined 2 in 1, 15/16 Amp with plastic box (multi purpose) ISI marked complete all as specified and directed.

S&F in repair pressed sheet metal enclosure (MCB DB), single phase and neutral with 200 Amps rated bus bar, double door type, 240 volts complete for the following no.of way:-

(c) 2 way but without bus bar

S&F MCB 40 Amp SPN 240 volt AC supply with rupturing capacity not less than 10 KA complete all as specified and directed.

S&F MCB 6 to 40 Amp SP 240 volt AC supply with rupturing capacity not less than 10 KA complete all as specified and directed.

S&F in repair PVC insulated flexible wire twin core twisted copper conductor of size 0.75 Sqmm (24/0.20) complete all as specified and directed.

S&F in repair PVC insulated, unsheathed, single core, multi-stranded, copper conductor cable, 1100 volt grade complete for the following :-

(a) 1.5 sqmm size

(b) 2.5 sqmm size

S&F 1100 volts grade heavy duty cable PVC insulated aluminium stranded conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connections twin core cable flat or circular 10 sqmm complete all as specified and directed.

S&F 1100 volts grade heavy duty cable PVC insulated aluminium stranded conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connections twin core cable flat or circular 6 sqmm complete all as specified and directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth for laying of cables or getting out existing unserviceable XLPE cables including getting out in hard dense soil complete all as specified and directed.

Description all as per Ser item No.37 here-in before but exceeding 1.5 mtr upto 3.0 mtr in depth complete all as specified and directed.

Returning filling in including spreading, levelling, and well ramming, in layers not exceeding 25 cm each layer of any type of soil complete all as specified and directed.

M&L for removing surplus excavated material to a distance not exceeding 50 mtrs from starting point and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

M&L for sand cushioning for underground cables with height of cushioning as 8 cm below the cable and 15 cm above the cable (total punned thickness 23 cm) complete all as specified and directed.

Supplying & laying unreinforced Precast Concrete cable cover of class LV, type 1 of size 250x150x40mm complete all as specified and directed.

M&L for cement concrete type D2 1:4:8 (40mm graded aggregate) as in foundation filling for pole/stay/ plinth or similar works completed all as specified and directed.

M&L for cement concrete type C2 1:3:6 (40mm graded aggregate) as in copping of poles complete all as specified and directed.

Supply & laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volt grade of crosssectional area 25 Sqmm 4 Core complete all as specified & directed.

All as per item srl No 45 here-in-before but of size 16 sqmm 4 core complete all as specified and directed.

All as per item srl No 45 here-in-before but of size 35 sqmm 3.5 core complete all as specified and directed.

All as per item srl No 45 here-in-before but of size 70 sqmm 3.5 core complete all as specified and directed.

S&F in repair GI tubing light grade of 50 mm bore as protection cover for cables to be laid under floor,along the wall or along the pole complete all as specified and directed.

S&F in repair steel tubular swaged pole complete with cast iron base plate finial taper plug, bolts, nuts and screws as specified type 410 SP-31 (9.0 mtr long) including painting with two coats of aluminium paint over one coat of red oxide primer, with black and white strips 30 cm each starting with black strip upto 1.5 mtr complete all as specified and as directed.

M&L for Structural steel work in replacement of existing unserviceable Cross arms bracing, supports, clamps and back plates fabricated from steel sections including nuts,bolts ,washers,welding ,bending cold or hot drilling holes for bolts in any shape or size as indicated or directed inclusive one coat of primercoat, one under coat and one finishing coat of aluminium paint complete all as specified and directed.

S&F in replacement pin type porcelain vitreous white, brown or green insulator of size 100 mm height,65 mm dia for 1100 volts grade including one galvanised mild steel spindle , one galvanised iron nuts and two washer for 1.1 KV working pressure complete all as specified and as directed.

S&F in replacement of shackle type porcelain vitreous, white brown or green insulator for working pressure 1.1 KV of size 75mm height and 90 mm dia including galvanized mild steel straps of section 31x3 mm size, 12 mm dia bolt nut and washers complete all as specified and directed

S&F in replacement of existing unserviceable Loop type insulator vitreous porcelan white,brown or green large size with overall dimensions 90X140mm clearance of hole 25.5.mm complete all as specified and directed. Make . Rastriya Electrical /Jai Shree /Jaipuriya/Hitkari/CJI

S&F in repair stay assembly complete with accessories such as stay plate 230mmx230mmx 6mm, stay rod 180cm long 16mm dia with nuts including GI bow, turn buckle etc. all as per electrical plate No. 01 of SSR Part-I 2009 (loop type insulator, stay strands, excavation, PCC will be measured & paid separately) complete all as specified and as directed.

S&F in repair galvanized steel stranded wire of size 7/3.15mm for stay assembly complete all as specified and directed.

S&F in repair galvanized steel wire 3.15/4.0mm dia as continuous earth wire/guard cradle horizontal/rectangular fabricated with 4mm dia galvanized mild steel binding wire complete all as specified and as directed.

M&L in replacement for ACSR conductor squirrel to dog (6/1/2.11 to 6/1/4.72) any size drawn straight horizontal on over head lines on existing poles including binding with insulators. Weight of conductor shall be measured straight horizontal distance between centre of two adjacent poles and calculating weight of conductor of size and length by adding 3% extra for sag ,jointing jumpers,etc complete all as specified and directed

S&F in replacement of existing unserviceable MCCB any size/capacity with MCCB 4 pole 63 Amps 25 KA Thermal magnetic setting type incl providing suitable thimbles/extended terminal with nuts,bolts and washers etc. complete all as specified and directed. Make: Havells/L&T/Legrand or equivalent. Note: The item rate includes minor additonal/alteration and extended terminal for fixing of MCCB and connecting of MCCB if reqd at site.

S&F in replacement of existing unserviceable MCCB any size/capacity with MCCB 4 pole 100 Amps 25 KA Thermal magnetic setting type incl providing suitable thimbles/extended terminal with nuts,bolts and washers etc. complete all as specified and directed. Make: Havells/L&T/Legrand or equivalent. Note: The item rate includes minor additonal/alteration and extended terminal for fixing of MCCB and connecting of MCCB if reqd at site.

S&F in replacement of existing unserviceable MCCB any size/capacity with MCCB 4 pole 200 Amps 25 KA Thermal magnetic setting type incl providing suitable thimbles/extended terminal with nuts,bolts and washers etc. complete all as specified and directed. Make: Havells/L&T/Legrand or equivalent. Note: The item rate includes minor additonal/alteration and extended terminal for fixing of MCCB and connecting of MCCB if reqd at site.

S&F in replacement of existing unserviceable MCCB any size/capacity with MCCB 4 pole 400 Amps 25 KA Thermal magnetic setting type incl providing suitable thimbles/extended terminal with nuts,bolts and washers etc. complete all as specified and directed. Make: Havells/L&T/Legrand or equivalent. Note: The item rate includes minor additonal/alteration and extended terminal for fixing of MCCB and connecting of MCCB if reqd at site.

S&F in replacement On load changeover switch of 4 pole 200 Amps, 415 AC capacity without enclosure confirming to IS :13947 (Part-3); including minor additional/ alternation for fixing and connecting up of changeover if required at site complete all as specified and directed. Make: Havells cat part No. IHBFFE0200 or equivalent in HPL/Standard

S&F in replacement On load changeover switch of 4 pole 100 Amps, 415 AC capacity without enclosure confirming to IS :13947 (Part-3); including minor additional/ alternation for fixing and connecting up of changeover if required at site complete all as specified and directed. Make: Havells cat part No. IHBFFE100 or equivalent in HPL/Standard

Labour only for taking out old/unserviceable insulators bindings and jumperings and tightening/restretching of the sagged ACSR Conductors/ GI earth continuous wire on pole including resecuring of insulators bindings and jumpering by using new aluminium binding wires complete all as specified and directed. Note: one span of Al conductor/GI wire from pole to pole will be measured as one unit/each run & all T&P involved shall deemed be included in the quoted rates .

M&L for scrapping of old paint from the steel tubular pole upto 9.0 mtr height with out removing accessories and preparation of surface for re-painting. Repainting the pole with one coat of alternative white and black straps of 30cm upto 1.5 mtr height using synthetic enamel paint starting with black strap. repainting the remaining pole and iron parts i.e. U clamps, channels, etc above 1.5mtr height by applying one coat of aluminium paint all as required at site or directed.

M&L for jointing and testing of End termination joint (heat shrinkable) suitable for 3.5 core 1.1 KV underground XLPE cable of size 25 to 50 sq mm including taking down existing unserviceable joint complete all as specified and as directed.

All as per serial item No.67 herein before but size of cable 70 to 120 sq mm complete all as specified and directed.

M&L for jointing and testing of straight through termination joint (heat shrinkable) suitable for 3.5 core 1.1 KV underground XLPE cable of size 25 to 50 sq mm including taking down existing unserviceable joint complete all as specified and as directed.

M&L for jointing and testing of straight through termination joint (heat shrinkable) suitable for 3.5 core 1.1 KV underground XLPE cable of size 70 to 120 sq mm including taking down existing unserviceable joint complete all as specified and as directed.

Dedcuct Credit for Demolished/Dismantled material Rs (-) 32982.00 (Minus) as listed in Schedule 'A' Part-II (Credit Schedule) Note : Tenderers will not quote against this item being a tentative amount, to be considered to arrive at the 'Contract Sum'.

M/S Web Company

osho traders