SPECIAL REPAIRS TO BLDG NO P-53 NAVAL MET OFFICE AND OTHER SANCTIONED WORKS UNDER GE HADDO, PORT BLAIR

Amount

Excavating in post holes (or similar holes) each not exceeding 0.5 Cum and getting out in hard/dense soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 m in depth, for foundation etc., or for shafts, wells, cess pits, manholes, pier holes etc not exc. 10 Sqm on plan and n.exc. 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each as in soils complete all as specified and as directed.

Removing excavated material (soils) to a distance not exceeding 50 metres and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L for PCC (1:3:6) type C1 (using 20mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

M&L for 100mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and as directed.

Demolition of PCC block masonry, built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

M&L for pre-cast cement concrete block masonry with solid blocks made up of (1:3:6) type C1 (using 20mm graded stone aggregate), masonry exceeding 10cm in width and setting in cement mortar (1:6) complete all as specified and directed.

M&L for pre-cast cement concrete block masonry with solid blocks made up of (1:3:6) type C1 (using 20mm graded stone aggregate), masonry not exceeding 10cm in width and setting in cement mortar (1:4) complete all as specified and directed.

Taking down existing roof membrane and removing the debris from site and cleaning the surface with water complete all as specified and as directed

M&L for plain cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggregate) as in roof padding, sunken floors and in similar works complete all as specified and as directed.

M&L for screed bed 15mm thick in CM (1:4) mixed with integral liquid water proofing compound as per manufacturer instructions on RCC roof surfaces, finished fair and even complete all as specified and as directed. NOTE: Water proofing compound will be measured and paid separately under relevant item of this schedule.

M&L for preparing plastered surfaces and applying a coat of cold applied bituminous primer over cleaned roof/ sunken surface @ 0.30 Kg/sqm and applying one coat of hot blown bitumen 85/25 grade @ 1.2 Kg/Sqm over primer followed by 3 mm thick APP modified 5-layered polymeric water proofing membrane weighing not less than 3.0 Kg/sqm reinforced with polyester non-woven fabric weighing not less than 150 grams/sqm laid as per the manufacturer instructions with side over lap of 100mm & end over lap of 150mm & tucked into the chases on roof, sunken slabs, edges and vertical surfaces and finally applying bitumen based heat resistant paint @ 0.30 litres/Sqm complete all as specified and directed. MAKE: STP Limited/ PIDILITE INDUSTRIES LIMITED (Dr. FIXIT TORCHSHIELD P3160)/ IWL INDIA LTD

M&L for applying bonding agent on old concrete surfaces (wall & ceiling) all as specified and as per manufacturers instructions, Over prepared surfaces provide 20mm thick high build polymer modified cement sand mortar (1:3) mixed with 7 litres (minimum) Nitobond SBR per 50 kilograms of cement of M/s FOSROC Chemical (India ) Pvt Ltd or equivalent in Dr. Fixit or Harjas Coatings & Polymers including necessary scaffolding up to 15 m and including match the existing shade of surface complete all as specified and directed

Cutting out existing crack in concrete surfaces/ masonry wall/ slab forming grooves of 25mm x 40mm size, cleaning the groove thoroughly with blower, applying primer coat of IPH CC or Hydroseal Siliconate Epoxy resin & Hardener mix in equal proportion with spray gun suitable to form a film on the surface of groove, filling the groove with putty made by mixing IPH CC of Make Harjas Coating & polymers or Hydroseal siliconate epoxy resin, resin hardener and admixture in proportion of 1:1:2 and finally applying sealing coat of the same mix in same manner as the primer is applied with following minimum coverage per running metre length of groove

Taking down cement plaster of any description on brick or stone walls etc., including raking out joints, hacking for key, scrubbing down with water etc., and removal of debris to outside MD land complete all as specified and as directed.

M&L for rendering 10mm thick in CM (1:4) on fair faces of brick work or concrete, surfaces finished fair and even complete all as specified and as directed.

M&L for aluminium composite panel sheet of 3.0mm thick with skin thickness of 0.25mm of aluminium on both sides, sandwiched by 2.5mm polyethylene core with PVDF coating of 30.0 micron fixed over frame made up of aluminium hollow section of 25x50mm, 2.0mm thick, duly fixed to wall/ceiling with expansion fastner having panels not exceeding 1200x1200mm with necessary silicon filling, in approved pattern as in columns, beams, walls etc., complete all as specified and as directed. NOTE: Necessary scaffolding required for the work shall be deemed to include in the unit rate quoted.

M&L for rendering 15mm thick in CM (1:6) on fair faces of brick work or concrete, surfaces finished fair and even complete all as specified and as directed.

Supply only liquid integral water proofing compound.

M&L for applying 2 to 3mm thick wall care putty on wall / ceiling surfaces complete all as specified and as directed

M&L for preparation of old plastered surfaces of walls by complete removal of existing treatment by scraping, washing, cleaning etc., and applying two coats of distemper oil emulsion over a coat of primer after filling the cracks with filler complete all as specified and as directed.

M&L for preparation of old plastered surfaces of ceiling by complete removal of existing treatment by scraping, washing, cleaning etc., and applying two coats of distemper oil emulsion over a coat of primer after filling the cracks with filler complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls of any description and applying two coats of distemper oil emulsion over a coat of primer after levelling the undulations if any with cement putty complete all as specified and as directed. Note: Wall putty will be measured and paid seperately.

M&L for preparation of newly plastered surfaces of ceiling of any description and applying two coats of distemper oil emulsion over a coat of primer after levelling the undulations if any with cement putty complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of external walls of any description and applying two coats of weather proof antifungal (exterior grade) acrylic emulsion over a coat of primer from the same manufacturer complete all as specified and as directed.

M&L for preparation of old plastered surfaces of walls by complete removal of existing treatment by scraping, washing, cleaning etc., and applying two coats of weather proof antifungal (exterior grade) acrylic emulsion over a coat of primer from the same manufacturer after filling the cracks with filler complete all as specified and as directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons, risers of steps, skirting, dado etc., laid bedded and pointed in any mortar complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for vitrified ceramic coloured tiles 9 to 10 mm thick (square/ rectangular) of approved shade, area of each tile not exceeding 0.36 Sqm as in floors etc., laid over and including 15mm thick screed bed in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for vitrified ceramic coloured tiles 9 to 10 mm thick (square/ rectangular) of approved shade, area of each tile not exceeding 0.36 Sqm, for work on vertical surfaces such as skirting, dados and risers to steps etc., including 10mm thick backing coat in CM (1:3), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors etc, laid over and including 15mm thick screed bed in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors etc, laid over and including 15mm thick screed bed in CM (1:4), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for glazed ceramic designed coloured tiles in vertical surfaces using size of tiles 450x300x7mm / 350x250x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with colour of tile with and including 10mm thick backing coat in CM (1:3), set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for chequered cement concrete tiles 30cm x 30cm x 25mm thick, made of grey cement and pigments, machine pressed as in flooring, set, jointed and pointed in neat cement slurry laid over and including 20mm thick screed bed in CM (1:4) complete all as specified and as directed.

M&L for mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W (Gde E-250) Quality 'B' complete all as specified and as directed.

M&L for mild steel hold fasts, bands, straps, supports or stays for rainwater, brackets/clamps for eaves/barge boards and valley gutter and similar articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

M&L for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

M&L for mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe-410-W (Gde-E-250) Quality 'A' complete all as specified and as directed.

M&L for preparation of old steel and iron surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coat of synthetic enamel paint of first quality complete all as specified and as directed.

M&L for preparation of new steel and iron surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint of first quality over a coat of red oxide zinc chrome primer complete all as specified and as directed.

S&F pre-painted zinc coated aluminum sheet (Galvalume) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers. Penetration and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc., as per SSR Part-I 2009 complete.

S&F pre-painted zinc coated aluminum sheet (Galvalume) GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall/valley gutters, fixed with self tapping screws including scaffolding for a height upto 12.0 metres complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers. Penetration and laps in sheet shall be sealed by using proper sealant profile. HDPE fillers shall be provided wherever required to close voids between sheets, sheet & fasteners etc., as per SSR Part-I 2009 complete.

S&F aluminum flat wind ties of any size and thickness fixed with self tapping screws for fixing roofing sheets complete all as specified and as directed. NOTES: The self tapping screw shall be of adequate length to drive into complete thickness of purlin/rafter etc., and shall be fixed using neoprene and EPDM washers.

Dismantling ceiling boards / wall cladding (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets and grid complete all as specified and as directed.

M&L for anodised aluminium snap grid frame work for false ceiling with size of grid 605mm x 605mm all as specified in SSR Part-I 2009, hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat iron 40x3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including cutting, drilling, jointing etc., including 6mm thick non-asbestos fibre cement building design boards fixed or laid/ inserted to aluminium frame work with screws complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames), area not exceeding 1.5 Sqm each complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames), area exceeding 1.5 Sqm but not exceeding 4.0 Sqm each complete all as specified and as directed.

M&L for powder coated anodised aluminium partition, window and door/ventilator with frame and shutters and grill fully or partly glazed, sliding/openable/fixed fully glazed and panels fixed with panels inserts 12 mm thick pre-laminated particle board/sheet glass including necessary jointing cleats, glazing clips, rubber beading, neoprene packing, anodised aluminium snap beading, screws, anodized aluminium fittings such as handles, aluminium butt hinges, aluminium tower bolts etc. The size of aluminium section shall be all as specified in relevant IS Code and SSR Part-I complete all as specified and as directed. NOTES: (i) Supply only floor spring, glass, Imax hinges, SS friction hinges, particle board, aluminium fly proof mesh will be measured and paid separately under relevant items of this BOQ. (ii) Weight of aluminium section only shall be accounted for the purpose of payment. However unit rate quoted shall be deemed to include for cost of rubber beading, neoprene packing, fittings such as handles, butt hinges, tower bolts, rollers for sliding windows, locking arrangement and fixing only of panel inserts of glass/ particle board/aluminium fly proof mesh etc. (iii) Weight of aluminium handle, butt hinges, tower bolts shall not be accounted for payment purpose.

S&F Second class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints including preservative treatment complete all as specified and as directed.

S&F 38mm thick rubber wood panelled shutter (02 Panels), with styles of 100mm, bottom and middle rail 100mm, top rail 150mm and panelled with 18mm rubberwood all as specified and as directed

S&F 38mm thick rubber wood glazed and skeleton shutter (04 Panels), with styles of 100mm, bottom and middle rail 100mm, top rail 150mm and panelled with glass or aluminium wire mesh all as specified and as directed. ( Note: Glass & wire mesh will be measured and paid separately)

M&L for preparation of new wooden surfaces and applying melamine polish through the process of sanding with wood sanding paper of size 60 & 80 and applying wood filler mixed with NCD thinner including applying wood putty on shabby/ nailing area and sanding with sand paper of size 120 and applying sealer and walnut colour stainer ad sanding with sand paper of size 320 ad melamine polishing with spray application and again sanding with 400 sand paper and finally applying waxpol (Silicon Make) with soft fine cloth for better shining and finishing complete.

Supply and fix in repairs stainless steel IMAX Hinges for aluminium window shutter

Supply only 5.5 mm thick plain sheet glass, pin head type and glazing with aluminium glazing clips in square, exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Supply only 4.0 mm thick plain sheet glass, pin head type and glazing with aluminium glazing clips in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Supply only aluminium expanded metal fly proof mesh, cut to required size and shape, with 0.45mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and as directed.

Supply only 12mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side with balancing white lamination complete all as specified and as directed.

M&L for 18/19mm thick MDF boarding (fire & water proof) as in cup boards exterior grade with one side white lamination and other side coloured prelaminated, size of cabinet as per requirement of the site complete all as specified and as directed. Make: Axis/ Greenply/ Archidply/Bajaj or equivalent Note: Cutting Edges of cupboard shutter/ shelves to be finished with adhesive edge binding tape all as directed

S&F Stainless steel auto closing hinges of standard size

S&F Stainless steel cupboard handle, fancy type of 150mm size

S&F Stainless steel tower bolt of 100mm size

S&F magnetic door catcher for cupboard

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube as per specification & drawing, fixed in opening complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail , lock rail and bottom rail on either side and as gap insert for top rail and bottom rail.Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with rails with supplying and fixing in the frame at site as per the direction of Engr-in-charge

S&F in repairs 100mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type C-21 complete all as specified and as directed.

S&F in 100mm size butt hinges, brass with stainless steel hinge pin, type C-21 complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F brass handles, size 150mm cast type, polished bright

S&F 150mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F 150mm Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed

S&F sliding door bolt, 300mm long, aluminium alloy, anodised, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed.

S&F Brass, sliding door bolt 300mm with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete

S&F PVC coated 20-30mm dia curtain rod, made of mild steel, any colour, with end globins and brackets fancy type complete all as directed and approved by Engr-in-charge

S&F door closer, aluminium (Die cast), hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, fixed in repairs with screws complete all as specified and as directed.

S&F in repairs 110mm bore PVC (SWR) pipes single socketed, in any length pipes single socketed, in any length with rubber ring joints, laid in trenches/fixed to walls/placed in weep holes using synthetic rubber adhesive cement solvent complete all as specified and as directed.

S&F PVC (SWR) bends any radius, diameter of outlet 110 mm complete all as specified and as directed.

S&F PVC (SWR) branch piece, (Single Y) equal or unequal, diameter of outlet 110 mm complete all as specified and as directed.

S&F PVC (SWR) multi floor trap with grating including jointing with solvent cement, diameter of outlet 75 mm complete all as specified and as directed.

S&F PVC (SWR) gully trap 125/110mm outlet dia jointing with solvent cement complete all as specified and as directed.

M&L for vitreous China wash hand basin, white, flat back, size 550mm x 400mm including cutting for and pinning in ends of brackets or erecting stand, 32mm dia waste coupling brass chromium plated, bottle trap 32mm bore brass chromium plated with necessary packing union and caps, chain and plug, PVC connections 15mm size with PTMT nuts of length 450mm, screwed down for iron pipe or for unions complete all as specified and as directed.

M&L for vitreous China, wash down water closet EWC (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device complete all as specified and as directed.

S&F in repairs PVC valveless, syphonic action type, flushing cistern, 10 litre capacity, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

S&F in repairs vitreous China urinal with top inlet, half stall type coloured complete fixing with suitable fixing arrangements to wall with and including cp urinal spreader, CP domed 32mm bore dia waste coupling and waste pipe complete all as specified and as directed

S&F two way bib cock, 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, ,screwed down, screwed both ends for iron pipe or for unions, complete all as specified and as directed.. MAKE: JAQUAR Cat part No. CON-041KN) or equivalent in PARRYWARE/ ZOLOTO/ JOHNSON

S&F angular stop cock, 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, with long shank and cup (concealed type) screwed down, screwed both ends for iron pipe or for unions complete all as specified and as directed. Make :Jaquar Cat part No. CON-053KN or equivalent in PARRYWARE/ PRAYAG/ JOHNSON

S&F WHB mixer, 15mm dia, cast copper alloy, chromium plated, fancy type, with crutch or butterfly handle, with long shank with central hole screwed down, screwed both ends for iron pipe or for unions, fixed in repairs complete all as specified and as directed. MAKE: JAQUAR Cat part No. CON-167KNB equivalent in PARRYWARE/ PRAYAG/ JOHNSON

S&F tubular towel rail, brass, chromium plated, 20mm dia, D type, 60cm long between flanges, fixed in repairs complete all as specified and as directed. MAKE: JAQUAR Cat part No. AQN-7711 or equivalent in PARRYWARE/ PRAYAG/ JOHNSON

S&F health faucet, brass, chromium plated with 8mm dia, 1.0 m long flexible tube, screwed for iron pipe or for brass ferrule 15mm dia or bore complete all as specified and as directed. MAKE: ZIM Cat part No. 1624A or equivalent in PARRYWARE/ PRAYAG

S&F in repair toilet paper holder, brass, chromium plated, complete all as specified and as directed. MAKE: JAQUAR Cat part No. ACN-1153N) or equivalent in PARRYWARE/ ZOLOTO/ JOHNSON

S&F soap dish, fixed in repairs complete all as specified and as directed. MAKE: JAQUAR Cat part No. AQN-7731 or equivalent in PARRYWARE/ PRAYAG/ JOHNSON

M&L for PVC connections 15mm size with PTMT nuts of length 600mm, complete all as specified and as directed.

S&F powder coated mild steel curtain rods including side globin and end brackets including 10 Nos riges per metre

M&L for Cutting chases in PCC block masonry walls, for shelves, lintels, edges of landing etc., and making good, cutting not exceeding 10 cm girth complete all as specified and directed.

Taking up or down 15mm dia steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20mm dia steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

S&F 20mm bore CPVC pipes SDR 13.5 & Plain CPVC SDR 11 fittings, fixed complete to walls, ceilings or in floors etc., (including concealing, if required) and to any type of pipe complete all as specified and as directed.

S&F 25mm bore CPVC pipes SDR 13.5 & Plain CPVC SDR 11 fittings fittings, fixed complete to walls, ceilings or in floors etc., (including concealing, if required) and to any type of pipe complete all as specified and as directed.

Disconnecting existing tanks of capacity exceeding 250Ltr and not exceeding 500Ltrs, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position.

S&F in repairs rotational moulded polyethylene water storage tanks, triple layered, ISI marked (cylindrical vertical with closed top), 500 litres capacity, hoisted and fixed in position all as specified in SSR Part I, 2009 including 20mm dia or bore PTMT ball valve high pressure with epoxy coated aluminium rod & high density plastic ball (minimum weight 455gms) screwed for iron pipe, provision of 40mm/25mm spouts for connecting inlet, outlet, over flow and washout pipes complete complete including taking down existing tank and offered as credit to contractor all as specified and as directed.

Taking down carefully old unserviceable aluminum/ copper point wiring (light, fan, socket or power) complete, including fittings & fixtures such as switches, ceiling roses, lamp holders, pendants, regulators sockets, light fittings, junction/terminal boxes etc; removing from site and making good disturbed surfaces of walls, floors etc., to match with existing surrounding surfaces complete all as specified and as directed.

Taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces to match with existing surrounding finishes complete all as specified and as directed.

Taking down existing unserviceable fuse units/ distribution boards of any description alongwith MCBs/MCCBs and making good disturbed surfaces to match with existing surrounding finishes complete all as specified and as directed.

Taking down carefully old unserviceable light fittings only and removing from site complete all as specified and as directed.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC casing and capping/ PVC Concealed conduit of suitable size (not less than 25mm) and accessories fixed on walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in CI boxes/pressed steel terminal boxes 60mm deep made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint outside and with two coats of aluminium paint inside and laminated sheet cover of 3mm thick on top for housing the switches, socket outlet etc, all as specified and as directed for ONE LIGHT/FAN point controlled by one, one way 6 Amps switch.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC Concealed conduit of suitable size (not less than 25mm) and accessories fixed on walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in CI boxes/pressed steel terminal boxes 60mm deep made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint outside and with two coats of aluminium paint inside and laminated sheet cover of 3mm thick on top for housing the switches, socket outlet etc, all as specified and as directed for Two LIGHT point controlled by one, one way 6 Amps switch.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC Concealed conduit of suitable size (not less than 25mm) and accessories fixed on walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in CI boxes/pressed steel terminal boxes 60mm deep made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint outside and with two coats of aluminium paint inside and laminated sheet cover of 3mm thick on top for housing the switches, socket outlet etc, all as specified and as directed for ONE 6A SOCKET OUTLET point controlled by one, one way 6 Amps switch on independent board.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC Concealed conduit of suitable size (not less than 25mm) and accessories fixed on walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in CI boxes/pressed steel terminal boxes 60mm deep made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint outside and with two coats of aluminium paint inside and laminated sheet cover of 3mm thick on top for housing the switches, socket outlet etc, all as specified and as directed for ONE 6A SOCKET OUTLET point controlled by one, one way 6 Amps switch on same board.

M&L for Point wiring complete with 1.5 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC Concealed conduit of suitable size (not less than 25mm) and accessories fixed on walls/ceilings etc., including provision of PVC insulated 1.5 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in CI boxes/pressed steel terminal boxes 60mm deep made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint outside and with two coats of aluminium paint inside and laminated sheet cover of 3mm thick on top for housing the switches, socket outlet etc, all as specified and as directed for One BELL point controlled by one, one way 6 Amps switch.

M&L for Point wiring complete with 4.0 Sqmm (nominal area) single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral), drawn through and including rigid non metallic PVC Concealed conduit of suitable size (not less than 25mm) and accessories fixed on walls/ceilings etc., including provision of PVC insulated 4.0 Sqmm FRLS cable with copper conductor green in colour for earth continuity and connected to common earth dolly and sunk in CI boxes/pressed steel terminal boxes 60mm deep made out of 1.6mm thick MS sheet duly painted with two coats of anti-corrosive paint outside and with two coats of aluminium paint inside and laminated sheet cover of 3mm thick on top for housing the switches, socket outlet etc, all as specified and as directed for ONE 16A SOCKET OUTLET point controlled by one, one way 16 Amps switch on independent board.

S&F switch piano, flush type, single pole, one way, 6 Amps, 240 volts complete all as specified and as directed.

S&F modular switch, one way, one module, single pole, 6 Amps complete all as specified and as directed.

S&F modular switch, one way, one module, single pole, 16 Amps complete all as specified and as directed.

S&F modular socket, multipurpose, 2/3 pin combined, 2 module, single pole, 6 Amps complete all as specified and as directed.

S&F modular socket, multipurpose, 2/3 pin, 6/16 Amps combined, 2 module, single pole, complete all as specified and as directed.

S&F modular electronic fan regulator for ceiling fan, step type, 5 speed, AC, 2 module, 120 watts, 240 volts complete all as specified and as directed.

S&F modular bell push, 6 amps, 1 module, 230 volts complete all as specified and as directed.

M&L for ceiling rose, three terminal, 65x20mm size, PVC/Polycarbonate, insulated body, 6A, 240 volts complete all as specified and as directed.

S&F electric bell, single pole, Ding Dong type, 230 volts, AC supply complete all as specified and as directed.

M&L for Sub main wiring complete with two runs (1P+1N) of 4.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral) and one run of 4.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor as earth wire green in colour including lugs, drawn through and including 32mm wide rigid non-metallic PVC casing and capping and its accessories (OR) 25mm dia PVC conduit and conduit accessories fixed on surface of wall/ceiling/roof/ floor complete all as specified and as directed. NOTE: Two runs of 4.0 Sqm copper conductor, One run of 4.0 Sqmm copper conductor as earth wire and one run of PVC casing and capping / PVC conduit shall be measured as one unit length.

M&L for Sub main wiring complete with two runs (1P+1N) of 6.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor (with colour coding of Red/Blue/Yellow for phase and Black for neutral) and one run of 6.0 Sqmm single core, PVC insulated unsheathed, FRLS cable, 1100 volts grade, multistranded copper conductor as earth wire green in colour including lugs, drawn through and including 32mm wide rigid non-metallic PVC casing and capping and its accessories (OR) 25mm dia PVC conduit and conduit accessories fixed on surface of wall/ceiling/roof/ floor complete all as specified and as directed. NOTE: Two runs of 6.0 Sqm copper conductor, One run of 6.0 Sqmm copper conductor as earth wire and one run of PVC casing and capping / PVC conduit shall be measured as one unit length.

S&F Tube light fittings LED 20 watts 4 feet including all accessories and fixing arrangements complete all as specified and directed Make :CG Cat Part No : CCS-100-20-65-HL2-DP-NWH/ Philips Cat Part No : Astra line plus/C&S/Havells

S&F MCB DB, SPN, 8-way, vertical type, double door, 240 Volts with 200 Amps rated bus bar, IP-54 protection, shrouded neutral bus bar, cement spill protector, concealed in wall and making good disturbed surfaces to match with surrounding surface complete all as specified and as directed. MAKE: INDO ASIAN Cat part No. 811826 or equivalent in L&T/ LEGRAND/ HAVELLS

S&F MCB DB, SPN, 12-way, vertical type, double door, 240 Volts with 200 Amps rated bus bar, IP-54 protection, shrouded neutral bus bar, cement spill protector, concealed in wall and making good disturbed surfaces to match with surrounding surface complete all as specified and as directed. MAKE: INDO ASIAN Cat part No. 811828 or equivalent in L&T/ LEGRAND/ HAVELLS

S&F MCB, SPN, 230 volts, 63 Amps, C series 10 KA rupturing capacity complete all as specified and as directed. MAKE: INDO ASIAN Cat part No : 811154 /L&T/ LEGRAND/ ABB/ HAVELLS

S&F MCB, SPN, 230 volts, 40 Amps, C series 10 KA rupturing capacity complete all as specified and as directed. MAKE: INDO ASIAN Cat part No : 811153 /L&T/ LEGRAND/ ABB/ HAVELLS

S&F MCB, SP, "C" series, 240 volts, 6 to 32 Amps, 10 KA rupturing capacity complete all as specified and as directed. MAKE: INDO ASIAN Cat part No. 811122 to 811129 or equivalent in L&T/ LEGRAND/ ABB/ HAVELLS

M&L for earthing complete with GI earth plate electrode of size 600mmx600mmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of the earth plate not less than 1.5m below normal ground level connected to 4mm dia GI earth wire as earth lead connected by means of bolts, nuts, washers and check nuts made out of galvanised iron or steel all as shown on electrical plate No. 3 of SSR Part-I connected to common earth dolly including testing on completion complete all as specified and directed. NOTES: 1) The unit rate shall also include for earth work in any type of soil, PCC (1:3:6) type C1 chamber, pre-cast RCC (1:2:4) type B-1 using 20mm graded stone aggregate cover 50mm thick reinforced with TMT bars 8mm dia @ 100mm c/c both ways, funnel with watering pipe 20mm dia medium grade, GI protection pipe light grade 40mm dia and wire mesh complete in addition to item No. 1(a) to (e) of preamble (notes) under sub-heading earthing, specified on Sl. Page Nos. 422 & 423 of SSR Part-II. 2) Earthing lead and GI protection pipe beyond 7.5m will be measured and paid separately.

S&F starter switch of capacity 25 Amps working on 240 Volts, AC supply suitable for split type airconditioner complete all as specified and as directed. MAKE: CRABTREE Cat part No. ACTO252504 or equivalent in ANCHOR/HAVELLS/L&T

S&F LED down light fixture of 18 Watts capacity, including 18 Watts LED lamp and testing complete all as specified and as directed. MAKE:CROMPTON GREAVES Cat part No. LCDSPLN-R-18-CDL or equivalent in HAVELLS/ WIPRO/

S&F mirror light fixture of 15 Watts capacity, including all accessories anf fixing arrangements complete all as specified and as directed. MAKE:LUKER Cat part No. LCML15 or equivalent in HAVELLS/ CG / WIPRO

S&F LED spotlight fixture of 09 Watts capacity, including all accessories anf fixing arrangements complete all as specified and as directed. MAKE:Havells Cat part No. LHEEGEPBIE1W009 or equivalent in CG / WIPRO

S&F bed side lamp fitting, 3W, 3000K, 150Lumen, metallic body including LED bulb complete all as specified and as directed. Make: Philips Model No: 48042 or Equivalent in CG/C&S/ Havells

S&F decorative LED wall light fitting, 20W, 3000K, metallic body including LED bulb complete all as specified and as directed. Make: Philips Model : Grace or Equivalent in CG/C&S/ Havells

S&F ceiling fan of three blades, remote controlled, 1200mm sweep, 340 RPM, 65% energy saving, suitable for AC 230 volts, heavy duty with down rod and canopies complete all as specified and as directed. MAKE: Atomberg Model: EFFICIO or equivalent in Havells/ Usha/ CG

S&F wall mounting type oscillating air circulating fan with remote control, 400mm (16") sweep, 1350RPM, working on 230 volts, 50 Hz, single phase, AC supply complete all as specified and as directed. MAKE: Atomerg, Model: Efficio or equivalent in Havells/USHA/ CG

Taking down LED fitting of any type and capacity and refixing in same or other location complete all as specified and as directed

S&F Exhaust fan 250 mm sweep, plastic body, 26 watts, energy efficient, with louvers including all fixing arrangement complete all as specified and directed Make: Atomberg Model : Efficio or equivalent in CG/ Havells/ Orient/ Usha

S&F Exhaust fan 150 mm sweep, Stainless steel finish, 6.5 watts, energy efficient, with louvers including all fixing arrangement complete all as specified and directed Make: Atomberg Model : Studio or equivalent in CG/ Havells/ Orient/ Usha

M&L for cutting channels, grooves or rebates n exc 15cm girth, and trimming surface with matching the existing colour code with putty all as specified and as directed by Engr-in-Charge

M&L for LT XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with aluminium conductor, 1100 volts grade, cross sectional area 2 core, 10 Sqmm laid in trenches/floors/ducts or fixed on poles/walls with suitable clamps/saddles or drawn through pipes etc., including connecting up with suitable size of lugs, glands and jointing material complete all as specified and as directed.

M&L for HDPE DWC (Double wall corrugated) pipe of size 77mm (Outer diameter) x 63mm (Inner diameter) along with connected accessories like couplers, bends, end caps etc., laid in trenches/floors/ducts or fixed on poles/walls for as in protection of LT/ HT cable complete all as specified and as directed.

M/S AMK CONSTRUCTIONS

B.R. ENTERPRISES

M/s Bismi Builders & Enterprises

M/s Ramesh Lal

RS ENGINEERING WORK

M/s V M K Construction

M/s S U Enterprises