REPAIR RESURFACING OF BITUMINOUS ROAD REPLACEMENT OF ROAD FURNITURE AND ROAD MARKING AREA OF AGE BR I UNDER GE NAMS

Material and labour for Repair to pot holes any depth, n.exc 1 sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc cutting around edges at least 30 mm in depthand making good by applying tack coat with bituminous primer @ 10Kg per 10 Sqm, putting in premixed bituminous macadam using bitumen @4%of weight of road metal, well rammed and sealed with binder @9.8kg/Sqm, blinded with 0.09 cum of stone chipping 6.3mm size and again well rammed to uniform surfaces, depth of pot hole exc 30mm complete all as specified and directed.

Material and labour for Repair to pot holes any depth, n.exc 1 sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc cutting around edges at least 30 mm in depth and depth of potholes n.exc 30mm and making good by applying tack coat with bituminous primer @5kg per 10 Sqm, putting in premix as specified for thin bituminous carpet (2cm thick), well rammed and sealed with premix sand seal coat (6.8kg of binder with 0.06 cum of sand) again well rammed complete, all as specified and directed

Material and labour for preparing of black top surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surfaces with air compresser to remove all the loose dirt and applying evenly a priming/tack coat with paving bitumen primer @5 kg/10 sqm with paving bitumen VG 10 and laying semi dense asphaltic concrete 30mm consolidated thickness with 5.5 percent binder content VG 30 by weight of total mix with mechanical paver mixing in hot mix plant, rolled and consolidated to required camber and gradient with 8 to 10 tonne mechanical power roller complete, all as specified and directed. Note :- (a) Material for SDAC shall be mixed in hot mixing plant duly approved by GE. (b) Job mix formula of bituminous SDAC will be got done from approved lab. (c) The SDAC shall be laid with mechanical sensor paver.

Material and labour Premixed bituminous, macadam laid/rolled and compacted to required gradient and camber using 20mm graded stone aggregate and paving bitumen @ 4% by the weight of total mix (consolidated thickness 75mm thick or less or as required) with 10 to 12 ton power roller complete, all as specified and directed.

Material and labour for preparing of black top surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all the loose dirt /dust etc and other deleterious, material and applying evenly a priming / tack coat using with bituminous primer of paving bitumen primer VG - 10 @ 10 Kg per 10 Sqm, of road surface complete, all as specified and directed.

Preparation of road surfaces and applying thermoplastic reflective paint in making of minimum 2.5mm thick single coat as in center line and wdge line road marking of 150mm width using 'HOT MARK' thermoplastic modern propelled road marking machine as direction inculding all ingredient such as blinder, glass beads Titanium dioxide calcium carbonate inter fillers thermoplastic requirement for glass beads shall be the table No 800.4 of MORTH specification including spraying of glass beads etc all as per manufacture instructions and as directed.

Supply and fixing in repair Solar Cat eye / Stud of size 125mmX125mmX25mm (Shank 60mm) with aluminium alloy shell, high efficiency Mono - crystalline solar pannel 2.40 V/0.30 Watt having one Ni-Mh are Ni-Cd rechargeble battery (1.2 V)/1600 MA), Six super bright LEDs with 10,000 to 18,000 mcd (Milli Candela) having flash rate 02 Hz and bearable weight 10 tons approx with view distance upto 1000 Mtrs of any colour i.e yellow, red, blue, green or white as required at site, working tem 10 degrees to 75 degrees C, working time 3 to 4 days after fully charged battery, charging time 5 to 6 hours from direct sun light, maint free unbreakable poly carbonate clear facing , automatically turns on at night and turns off at dawn including all fixing arrangement as per manufactures instructions complete, all as specified and directed.

Supply and fixing in repair CAT'S EYE made out of strong thermoplastic material of technocommercial and to be fixed with Epoxy - Resin based adhesive or special Hot Melt Bitumen adhesive avoiding nails etc complete all as specified and directed. Make: DA 971P of Dark eye or Series 290 of 3M or GPL-BS-02-11 of Green Lite or equivalent as per list of makes.

Supply and fix in repair CAT'S EYE solar reflective type of metal body alloy of size 100mmX100mmX20mm with PMMA striplens reflector fixed with end and including MS stud of suitable size as per manufacturer's instructions etc complete all as specified and directed. Make: Model No. DA 972.0 of Dark Eye or Equivalent as per list of makes.

Supply and fixing in repair for road delineator ABS round body, reflective reflectors (Amber/Red colour) and mounted on MS pipe 50mm dia duly powder coated overall length 850mm fitted with anti rust and theft steel net including welding of mild steel flat iron at bottom of delineator of size 25x5mm, 150mm long, necessary excavation and embeded in PCC block 1:2:4 type B1 of size 30x15x30cm complete, all as specified and directed.