SPECIAL REPAIRS TO BLDG NO. T-11 (OR COOK HOUSE) AND T-15 OF GE 872 EWS, SPECIAL REPAIRS TO CEILING FANS, EXHAUST FANS AND WALL FANS AGAINST BER FOR LIKABALI AND NLP MIL STNS AND PROVN OF CERTAIN EM MINOR WORKS AT LIKABALI MIL STN UNDER GE 872 EWS

Amount

B/R SERVICES/WORKS

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and Removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Brick Work or Pre-cast Concrete Block Masonry, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) not exc. 1.50 Square Metre Each, complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) of any description, exc. 1.50 Square Metre but not exc. 4.00 Square Metre Each, complete all as specified and as directed.

Taking down/out Unserviceable Rusted/Worn out Wire Cloth/Netting of any description, fixed with Beads, etc., complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheeting of any gauge and thickness, Segregating Serviceable Plain or Corrugated Steel Sheeting and Stacking properly at Sites and Keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Frame Work and Cover Fillets, complete all as specified and as as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

M&L Pre-cast Cement Concrete Block Masonry with Solid Blocks of Size 300x200x100mm, having Compressive Strength of not less than 100 Kg/ Sq Cm (as per IS-2185) in Cement Concrete 1:3:6 (20mm graded stone aggregate), 10 Cm in Width and Setting in Cement Mortar 1:4, complete all as specified and as directed.

M&L Cutting Holes in Brick/ Pre-cast Concrete Block Walling, not exc. Half Brick thick, built in Cement Mortar for inserting of Holdfasts, Lugs, etc. and Making Good to Dismantled portion with Cement Concrete 1:2:4 (20mm graded stone aggregate) or Cement Mortar 1:3 (as required) and Adjoining Surfaces in Cement Mortar 1:4, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain, Solid, Straight, Chowkats and Frame, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue pinned at Joints, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Panelled Shutter 35mm thick (any number Panels) Plain, Framed with Lock Rails, having Panels of 12mm thick BWP, Commercial Ply or 12mm thick Veneered Particle Board Medium density, Wood Particle Board with Commercial Face Veneers and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 35mm thick, Open rebated and prepared to receive Glass, Gauze, etc., divided into Squares, with plain, chamfered or rounded, mitred and rebated Sash Bars (any numbers), fitted with cut and mitred beads for Glass, Gauze, etc., Sizes of Members of Shutters as specified in MES Schedule Part-I, Section 8, Clause No. 8.24(a) and fitted to Chowkats, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 30mm thick, Open rebated and prepared to receive Glass, Gauze, etc., divided into Squares, with plain, chamfered or rounded, mitred and rebated Sash Bars (any numbers), fitted with cut and mitred beads for Glass, Gauze, etc., Sizes of Members of Shutters as specified in MES Schedule Part-I, Section 8, Clause No. 8.24(b) and fitted to Chowkats, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt of Size 125mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt of Size 150mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt 300mm long with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of Size 75mm, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of Size 100mm, complete all as specified and as directed.

S&F Aluminium Handle of Size 125mm, anodised, Cast type, complete all as specified and as directed.

S&F Aluminium Handle of Size 150mm, anodised, Cast type, complete all as specified and as directed.

S&F Floor Door Stopper with Overall length of Cover Plate 150mm of Aluminium Alloy Body and Tongue (as approved) anodised, with Hard Drawn Steel Spring, fixed in Floor, complete all as specified and as directed.

S&F Mild Steel 300mm, Ordinary Rat Tail Rod pattern Springs including Roller and Roller Plate, complete all as specified and as directed.

M&L Stainless Steel Curtain/ Drapory Rod having 24mm Outer dia with Wall thickness 1.00mm (minimum) including Brackets, Side Holders and Rings, etc. and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

S&F Sheet Glass 3.0mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

M&L Mild Steel Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes including Bolts, Hooks (Stay) for large Gates; Hook and Pintle Hinges: Large Hasps and Staples; Hand Made Sliding Bolts; Clamps; Holdfasts (Flat Iron of Size 25x3.0mm); Wall Ties and similar Small Articles, conforming to Fe-290 Gde-E-165, complete all as specified and as as directed.

S&F Corrugated Mild Steel Sheeting 0.63mm thick, Galvanised @120 Gram Per Sqm, with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

M&L Re-fixing Corrugated Mild Steel Sheeting 0.63mm thick (Serviceable Sheeting obtained from Item No. 1.06 here-in-before) with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Plain Mild Steel Sheeting 0.80mm thick, Galvanised @ 120 Gram Per Sqm, in Ridges, Hips, Valley Gutters, etc., fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/ Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Exposed Suspended False Ceiling System with GI Powder Coated Snap Grid/ Frame Work of Size 605x605mm, all as per Specification and Drawing of MES Schedule (except Hangers), complete all as specified and as directed.

S&F Hangers 4.0mm dia GI (upto 1200mm length) for adjusting Level, fixed to Roof Slabs by means of Ceilling Cleats made out of GI Flat 40x3.0mm in Size, 60mm long and Expansion Hold Fasteners 12.5mm dia, 40mm long, complete all as specified and as directed.

S&F HSPC Non-Asbestos Fibre Cement Building Boards 4.0mm thick, Pre-primed, Self Embossed, Textured Designer Boards, Water Resistant, Termite Resistant, Fire Resistant for insulation, fixed or laid/ inserted to GI/ Aluminum Snap Grid Frame Work with Screws, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 25mm thick as Base Course for laying Tiles on Flooring, etc., finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Non-skid Ceramic Coloured/Designer Tiles, Joint Free (1st quality as approved) 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-skid Ceramic Coloured/Designer Tiles, Joint Free (1st quality as approved) 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 100mm thick in Floors, etc., Laid in Alternate Panels, finished Concrete Surfaces Fair and Even without using Extra Cement, complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) 75mm thick in Plinth Protection, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick on Bricks/Pre-cast Blocks or Concrete Works consisting in 2 layers, Backing/Under layer of 10mm thick in Cement Mortar 1:4 and Float/Top layer 5.0mm thick in Cement Mortar 1:4 including mixing WPC to Float/Top layer, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured and Paid separately under appropriate Item,

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing New/Old Plastered Surfaces of Walls and applying Two Layers of Wall Care Putty 3.0mm thick (1.5mm thick of Each Layer) on Plastered Surfaces of Walls including Cutting and Rubbing down to obtain a Even and Smooth Surface, complete all as specified and as directed.

M&L Applying Two Coats of Distemper Oil Emulsion (of approved Tint) over a Coat of Chalk Whitening (Priming Coat) on Putty Finished Surfaces of Walls, complete all as specified and as directed.

M&L Applying One Coat of Distemper Oil Emulsion (of approved Tint) on Putty Finished Surfaces of Walls, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint (of approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Old Decorated/Treated Plastered Surfaces of Walls and applying One Coat of Cement Base Paint (of approved Tint), complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, exc. 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality Paint of approved Tint), complete all as specified and as directed.

M&L Preparing Old Treated Steel and Iron Surfaces of any descriptions, exc. 10 Cm in Width or Girth and Applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of Wood and Wood Based Materials, of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Backs of Chowkats, etc. Area tarred exc. 0.10 Sqm but not exc. 0.50 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Holdfast or similar Small Items, Area tarred not exc. 0.10 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors including Taking down/up Unserviceable Galvanised Steel Tubing with Fittings of any description from any Situations, complete all as specified and as directed.

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors including Taking down/up Unserviceable Galvanised Steel Tubing with Fittings of any description from any Situations, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, Fancy type, with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and Fixed-in-repairs, complete all as specified and as directed.

S&F Pillar Tap 15mm bore (dia), Cast Copper alloy, Chromium Plated, Swan Neck with Capstan Heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with Long Screwed Shanks and Fly-nuts, screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Stop/Angle Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repairs, complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 500 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS:12701-1996, hoisted and fixed in Position all as specified in MES Schedule and providing Water Connections including Lowering down unserviceable Water Storage Tank of any description after disconning of all Water Supply Connections, complete all as specified and as directed.

S&F PTMT Ball Valve 20mm bore (dia), having weight not less than 210 Gram, high pressure with Epoxy Coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Vitreous China White Wash Hand Basin 550x400mm in Size, Oval shape, Counter Top with Brass Chromium Plated Waste Fitting 32mm bore (dia) and PVC Waste Pipe 40mm/32mm bore (dia) including a Pair of Cast Iron Brackets Brackets Erecting Stand duly Painted, Cutting and Pinning in Ends and Making Good disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Circular Grating 100mm dia (as approved) and fixing on Trap Loose or with Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed.

E/M SERVICES/WORKS

M&L Taking down carefully Copper Point Wiring (Light, Fan, Socket or Power) complete from in any Position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets but excluding Light Fittings of any description, Making Good Disturbed Surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Taking down unserviceable Service Connection including Connected Items of any description, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade FRLSH PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade FRLSH PVC insulated, unsheathed, multi-stranded single core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN/ BELL POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade FRLSH PVC insulated unsheathed, multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade FRLSH PVC insulated unsheathed, multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire for ONE 3/5 PIN SOCKET 6 AMP POINT on SAME BOARD, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade FRLSH PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade FRLSH PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt grade FRLSH PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt grade FRLSH PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Switch Piano 46 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Socket Outlet 6 Amp, 5 Pin, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Socket Outlet 08 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Switch Socket Combination 6 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Switch Socket Combination 08 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Switch Socket Combination 6/16 Amp, 3 Pin, 2-in-1, Multi-plug, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Switch Socket Combination 08 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Lamp/ Angle Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and connecting up, complete all as specified and as directed. NOTE : Unserviceable Lamp/ Angle Holder 03 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Ceiling Rose 21 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Ceiling Fan Regulator, Dimmar Switch type, 230 Volt AC, Rotary Stepped, Electronic type 120/280 Volt and connecting up, complete all as specified and as directed. NOTE : Unserviceable Fan Regulator 04 No. derived from Taking down of Point Wiring will be catered under Schedule of Credit.

S&F LED Adore 15 Watt, B-22 CDL, 3 Star Ball Lamp with 6500K including Taking down/ out Unserviceable Lamp (03 No.) of any description, complete all as specified and as directed. NOTE : Unserviceable Lamp 03 No. against Taking down of Point Wiring will be catered under Schedule of Credit.

S&F LED Bulk Head Light Fitting 1x6 Watt having Plastic Housing with Clear Prismatic Diffuser LED 6 Watt Lamp and connecting up with and including suitable Size and Length Twisted Flexible Copper Conductor Cable including Taking down Unserviceable Light Fitting (04 No.) of any description, complete all as specified and as directed. NOTE : Unserviceable Light Fitting 04 No. against Taking down of Point Wiring will be catered under Schedule of Credit.

S&F Decorative Wall Light Fixture 1x10 Watt with 10 Watt LED Bulb/ Lamp, made of Polycarbonate and connecting up with and including suitable Size and Length Twisted Flexible Copper Conductor Cable including Taking down Unserviceable Light Fitting (06 No.) of any description, complete all as specified and as directed. NOTE : Unserviceable Light Fitting 06 No. against Taking down of Point Wiring will be catered under Schedule of Credit.

S&F LED Tube Light Fitting 1x20 Watt, 4 Feet long with LED 20 Watt Integrated Batten and connecting up with and including suitable Size and Length Twisted Flexible Copper Conductor Cable including Taking down Unservice-able Light Fitting (13 No.) of any description, complete all as specified and as directed. NOTE : Unserviceable Light Fitting 13 No. against Taking down of Point Wiring will be catered under Schedule of Credit.

S&F LED Panel (2'x2') Light Fitting 28-32 Watt with High Brightness SMD LEDs as Light Source, Enviromentaly Friendly, New Generation, Ultra Modern, Recess/ Ceiling mounting with Electronic Driver 28-32 Watt, complete with all Accessories, Pre-wired and connecting up with suitable Size and Length Twisted Flexible Copper Conductor Cable, 3 Core including Taking down Unserviceable Light Fitting (04 No.) of any description, complete all as specified and as directed. NOTE : Unserviceable Light Fitting 04 No. against Taking down of Point Wiring will be catered under Schedule of Credit.

M&L Taking down Ceiling Fan of any Make and Sweep from any Height after disconnecting Electric Connection and Keep in Safe Custody for Re-fixing/Re-hanging, complete all as specified and as directed.

M&L Re-hanging/Refixing only Ceiling Fan (obtained from BOQ Item No. 2.19 here-in-before) and connecting with and including suitable Size Twisted Flexible Copper Conductor Cable from Ceiling Rose to Connector of the Fan, complete all as specified and as directed.

Supply & Hanging Ceiling Fan 1200mm Sweep with Brush Less Direct Current (BLDC) Motor, Minimum Air delivery 210 CFM with Serving Value 6.00 BEE, 5 Star rated, 230 Volt, 50 Hz, Single Phase AC, comprising of Blades, Holding Down Rod, Electronic Fan Regulator and Accessories, Warranty Minimum 4 Years, Providing Electric Connection from Ceiling Rose to Fan with and including Twisted Flexible Copper Conductor Cable of suitable Size and Length, 3 Core, complete all as specified and as directed.

S&F Wall/ Ventilating Fan 300mm Sweep, 1350-1400 RPM, Single Phase, 45-50 Watt, 220-240 Volt with Fixing Arrangement using Fastener, complete all as specified and as directed.

S&F Metallic Anti-Dust Body Exhaust Fan 300mm Sweep with Louver, 1350-1400 RPM, Single Phase, 230/240 Volt with Fixing Arrangement using Fastener, Providing Electric Connection from Ceiling Rose to Exhaust Fan with and including Copper Conductor Cable of suitable Size and Length, 3 Core, complete all as specified and as directed.

S&F Metallic Body Exhaust Fan 450mm Sweep with Louver, Heavy Duty, Single Phase, 230/240 Volt with Fixing Arrangement using Fastener, Providing Electric Connection from Ceiling Rose to Exhaust Fan with and including Copper Conductor Cable of suitable Size and Length, 3 Core including Removing old Unserviceable Exhaust Fan to AGE E/M Store Yard and deposited, complete all as specified and as directed.

S&F MCB Single Pole 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up, complete all as specified and as directed. NOTE : Unserviceable MCB 10 No. obtained from Taking down/ out will be catered under Schedule of Credit.

S&F MCB Single Pole & Neutral 40 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up, complete all as specified and as directed. NOTE : Unserviceable MCB 02 No. obtained from Taking down/ out will be catered under Schedule of Credit.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 8-Way, SPN, 240 Volt, Single Door, Epoxy Based Powder Coated Painted, suitable for mounting MCB DP/SPN as Incomer and MCB SP as Out-going with 200 Amp rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links and connecting up including Taking down/out unserviceable MCB DBs of any description, complete all as specified and as directed. NOTE : Unserviceable MCB DBs 02 No. obtained against Taking down/ out will be catered under Schedule of Credit.

Excavating in Trenches, not exc. 1.50 Metre Wide and Depth not exc. 1.50 Metre for Taking out/up and Laying of Cable, Electric Pole, etc., Forming Surfaces to required Foundation, etc. and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering, Well Ramming in Layers not exc. 25 Cm, Providing Heaps along the Route of the Cable Line with Surplus Soil in Soft/Loose Soil, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) in Copping of Poles, etc., weathering slightly rounded or chamfered angle and throating, finishing all Exposed Faces of Concrete including necessary Earthwork and Formwork, complete all as specified and as directed.

S&F LED Post Top Light Fitting, New Generation, Environmental Friendly, Energy Saving, Long Life, Aesthetically Designed, Aluminium Landscape Luminaire for Diffused Lighting with High Power LED as Light Source, IP-65 protected, Providing Electric Connections including Taking down Unserviceable Light Fitting of any description, complete all as specified and as directed.

M&L PVC Conduit/ Pipe 20mm dia suitable for passing XLPE insulated, LT Armoured Electric Cable, laid in Trenches or under Roads/ Flooring/ Culverts and/or fixing to Electric Poles with suitable size Mild Steel Flat Iron Clamps, Bolts, Nuts, Washers, etc., complete all as specified and as directed.

Supply and Laying or Fixing or Passing through Pipe, 1100 Volt grade Heavy duty Cable with PVC insulated Aluminium Stranded Conductor served with an Inner sheathing of PVC Tape armoured with Galvanised Steel Wire or Tape and Overall PVC sheathed, Nominal Cross Section 6.0 Sqmm, 4 Core in Service Connection, complete all as specified and as directed.

Supply and Laying or Fixing or Passing through Pipe, 1100 Volt grade Heavy duty Cable with PVC insulated Aluminium Stranded Conductor served with an Inner sheathing of PVC Tape armoured with Galvanised Steel Wire or Tape and Overall PVC sheathed, Nominal Cross Section 10 Sqmm, 2 Core in Service Connection, complete all as specified and as directed.

M&L XLPE insulated, Armoured, Heavy duty, Electric Cable with Aluminium Stranded Conductor, 1100 Volt grade, Cross-sectional Area 10 Sqmm, 2 Core, laid in Trenches/ Ducts or Passing through Pipe or Fixing on Poles, etc., complete all as specified and as directed. NOTE : Necessary Earthworks, Sand Cushioning, Cable Protection Cover/ Bricks, GI Pipe, etc. will be Measured and Paid separately under relevent Items

M&L XLPE insulated, Armoured, Heavy duty, Electric Cable with Aluminium Stranded Conductor, 1100 Volt grade, Cross-sectional Area 95 Sqmm, 3½ Core, laid in Trenches/ Ducts or Passing through Pipe or Fixing on Poles, etc., complete all as specified and as directed. NOTE : Necessary Earthworks, Sand Cushioning, Cable Protection Cover/ Bricks, GI Pipe, etc. will be Measured and Paid separately under relevent Items

M&L Sand Cushioning (dry) in Trenches/Ducts for protection of UG Cables (below, above and around the UG Cable laid) of 23 Cm Spread thickness (8 Cm in depth before laying the Cable and 15 Cm in depth after laying the Cable) and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. NOTE : For the purpose of Payment, Punned thickness of Sand Cushioning only will be Measured.

Supply & laying Sub-class ‘B’ Bricks of Size 230x115x75 mm, Kiln burnt, for Covering to UG Cable as Protection, laid Flat, Transversally Width Equal to the Length of the Cable, complete all as specified and as directed.

Supply, Installation & Commissioning LT Panel Board, Factory Made (CPRI Approved/ Tested Manufacturer), made out of 16 SWG CRCA Sheet with Mild Steel Angle Iron Frame 50x50x6.0mm, Outdoor type, Totally Enclosed, Front Opening with Locking Arrangements, suitable for 415 Volt, 3 Phase, 4-Wire System, 50 Hz Supply having 4 Strips Copper Bus-bars 100 Amp rated 45 Cm Long, Dust Proof and Vermin Proof (IP-54), Epoxy Powder Coated Painted and Mild Steel Angle Iron Frame grouting in Cement Concrete 1:2:4 (20mm graded Stone aggregate), Providing all Electric Connections and Testing, Comprising with and including following Accessories, complete all as specified and as directed:- (a) MCB 32 Amp, 2 Pole, 16 kA, C Series, 230 Volt - 01 No. (b) MCB 16 Amp, SPN, 16 kA, C Series, 230 Volt - 05 No. (c) Indicating Lamp LED type in Incomming Phase - 01 Set (d) Internal Wiring with PVC insulated Copper Conductor Multi-stranded Cable 1100 Volt grade IS-694 marked of appropriate Gauge including Copper Lugs (h) Connection from MCB to Bus-bars with Solid Copper Conductor.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of Size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing including Taking down/out unserviceable Earthing (02 Set) of any description, complete all as specified and as directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick burried directly in Ground (Earth Pit not less than 2.25 Metre below Ground Level) with Top edge of the Plate not less than 1.50 Metre below Ground Level, connected with and including Galvanised Earth Strip of size 32x6.0mm by means of Bolts, Nuts, Check nuts and Washers of GI or Steel and connected Earthing Testing Point/Bus-bar with GI 40mm bore (dia) Light grade Protection Pipe, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc. 150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on Completion, complete all as per specified and as directed. NOTE : All Joints should be joined by Exothermic Welding or Brazing.

M/S Abhi Traders

M/S S.P. ENTERPRISES