Loading…
Loading…
Tender Value
₹7.0 Cr
EMD Value
₹13.9 L
Closing Date
7 Sept 2026, 3:00 pm
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
GENERAL
19 conditions · 2 needing a document upload
Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees, N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. SPECIAL NOTE:- The balance sheet and all other financial documents attested/certified by CAs to substantiate fulfilment of Financial Eligibility Criteria should be with UDIN, failing which the offer is likely to be rejected without any further reference. (Authority: CE's letter No.- CE/G/Arb& Cont. Mgt./Tender Circular/Pt.1/317, Dated: 11:03.2025)
Technical Eligibility Criteria: (a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender. (b) (1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2)In such cases, what constitutes a component in a composite work shall be clearly pre- defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing.
However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by the Railway. In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract, with prior approval of Chief Engineer in writing. Note for Technical Eligibility Criteria: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Credentials if submitted in foreign currency shall be converted into Indian currency i.e., Indian Rupee as under: The conversion rate of US Dollars into Rupees shall be the daily representative exchange rates published by the Reserve Bank of India or entity authorized by RBI to do so for the relevant date or immediately previous date for which rates have been published. Where, relevant date shall be as on the last day of month previous to the one in which tender is invited. In case of any other currency, the same shall first be converted to US Dollars as on the last day of month previous to the one in which tender is invited, and the amount so derived in US Dollars shall be converted into Rupees at the aforesaid rate. The conversion rate of such currencies shall be the daily representative exchange rates published by the International Monetary Fund for the relevant date or immediately previous date for which rates have been published.
[Explanation for Eligibility Criteria: 1. Substantially Completed Work means an ongoing work in which payment equal to or more than 90% of the present contract value (excluding the payment made for adjustment of Price variation (PVC), if any) has been made to the contractor in that ongoing contract and no proceedings of termination of contract on Contractor's default has been initiated. The credential certificate in this regard should have been issued not prior to 60 days of date of invitation of present tender. 2. In case a work is started prior to 07 (seven) years, ending last day of month previous to the one in which tender is invited, but completed in last 07 (seven) years, ending last day of month previous to the one in which tender is invited, the completed work shall be considered for fulfillment of credentials. 3. If a work is physically completed and completion certificate to this extent is issued by the concerned organization but final bill is pending, such work shall be considered for fulfillment of credentials. 4. In case of completed work, the value of final bill (gross amount) including the PVC amount (if paid) shall be considered as the completion cost of work. In case final bill is pending, only the total gross amount already paid including the PVC amount (if paid) shall be considered as the completion cost of work. In case of substantially completed work, the total gross amount already paid including the PVC amount (if paid), as mentioned in the certificate, shall be considered as the cost of substantially completed work. 5. If a bidder has successfully completed a work as subcontractor and the work experience certificate has been issued for such work to the subcontractor by a Govt. Organization or public listed company as defined in Note for Item 10.1 Para 10 of the Tender Form (Second Sheet) of GCC April - 2022, the same shall be considered for the purpose of fulfillment of credentials.
6. In case a work is considered similar in nature for fulfillment of technical credentials, the overall cost including the PVC amount (if paid) of that completed work or substantially completed work, shall be considered and no separate evaluation for each component of that work shall be made to decide eligibility. 7. In case of newly formed partnership firm, the credentials of individual partners from previous propriety firm(s) or dissolved previous partnership firm(s) or split previous partnership firm(s), shall be considered only to the extent of their share in previous entity on the date of dissolution /split and their share in newly formed partnership firm. For example, a partner A had 30% share in previous entity and his share in present partnership firm is 20%. In the present tender under consideration, the credentials of partner A will be considered to the extent of 0.3*0.2*value of the work done in the previous entity. For this purpose, the tenderer shall submit along with his bid all the relevant documents which include copy of previous partnership deed(s), dissolution deed(s) and proof of surrender of PAN No.(s) in case of dissolution of partnership firm(s) etc. 8. In case of existing partnership firm, if any one or more partners quit the partnership firm, the credentials of remaining partnership firm shall be re-worked out i.e., the quitting partner(s) shall take away his credentials to the extent of his share on the date of quitting the partnership firm(e.g. in a partnership firm of partners A, B & C having share 30%, 30% & 40% respectively and credentials of Rs 10 crore; in case partner C quits the firm, the credentials of this partnership firm shall remain as Rs 6 crore). For this purpose, the tenderer shall submit along with his bid all the relevant documents which include copy of previous partnership deed(s), dissolution deed(s) and proof of surrender of PAN No.(s) in case of dissolution of partnership firm(s) etc.
9. In case of existing partnership firm if any new partner(s) joins the firm without any modification in the name and PAN/TAN no. of the firm, the credentials of partnership firm shall get enhanced to the extent of credentials of newly added partner(s) on the same principles as mentioned in item 6 above. For this purpose, the tenderer shall submit along with his bid all the relevant documents which include copy of previous partnership deeds, dissolution/splitting deeds and proof of surrender of PAN No.(s) in case of dissolution of partnership firm etc. 10. Any partner in a partnership firm cannot use or claim his credentials in any other firm without leaving the partnership firm i.e., In a partnership firm of A&B partners, A or B partner cannot use credentials of partnership firm of A&B partners in any other partnership firm or propriety firm without leaving partnership firm of A&B partners. 11. In case a partner in a partnership firm is replaced due to succession as per succession law, the proportion of credentials of the previous partner will 1.4.1 be passed on to the successor. 12. If the percentage share among partners of a partnership firm is changed, but the partners remain the same, the credentials of the firm before such modification in the share will continue to be considered for the firm as it is without any change in their value. Further, in case a partner of partnership firm retires without taking away any credentials from the firm, the credentials of partnership firm shall remain the same as it is without any change in their value. 13. In a partnership firm "AB" of A&B partners, in case A also works as propriety firm "P" or partner in some other partnership firm "AX", credentials of A in propriety firm "P" or in other partnership firm "AX" earned after the date of becoming a partner of the firm AB shall not beadded in partnership firm AB. 14. In case a tenderer is LLP, the credentials of tenderer shall be worked out on above lines similar to a partnership firm. 15. In case company A is merged with company B, then company B would get the credentials of company A also.]
Defination of Similar Work :- Any civil engineering works.
125 conditions · 6 needing a document upload
Checklists for submission of documents while submitting the tender. : It shall be mandatory to submit the following documents (relevant to the nature of the firm) along with offer.
If the accepted tender value is more than 5% below the advertised tender value, the contractor shall submit an additional Performance Guarantee at the rate of 5% of the contract value. (Authirity : Advance Correction Slip No. 11 to IRS GCC April-2022)
For Partnership firm/Joint Venture (JV) / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc.: - Please submit a Self-certificate by attorney/authorized signatory/each member of Partnership firm/Joint Venture (JV) / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. in the prescribed format as Annexure-V(A). Non submission of the certificate, or submission of certificate either not properly filled in, or in a format other than the prescribed format shall lead to summary rejection of your offer.
Fulfillment of Standard Technical and Financial Criteria as per tender documents.
(a) Sole Proprietorship Firm: (i) All documents in terms of Para 10 of the Tender Form (Second Sheet) IRSGCC April-2022.
(b) HUF: (i) A copy of notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF. (ii) All other documents in terms of Para 10 of the Tender Form (Second Sheet) IRSGCC April-2022.
(c) Partnership Firm: The following documents shall be submitted by the partnership firm, with the tender: (i) A notarized copy of the Partnership Deed or a copy of the Partnership deed registered with the Registrar. (ii) A notarized or registered copy of Power of Attorney in favour of the individual to tender for the work, sign the agreement etc. and create liability against the firm. (iii) An undertaking by all partners of the partnership firm that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP in which they were / are partners/members. Any Concealment / wrong information in regard to above shall make the bid ineligible or the contract shall be determined under Clause 62 of the Standard General Conditions of Contract. (iv) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of IRSGCC April-2022.
(d) Joint Venture (JV) (If applicable): The tenderer shall submit all documents as mentioned in para 17 of the Tender Form (Second Sheet) of IRSGCC April-2022.
(e) Company registered under Companies Act 2013: (i) The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company (ii) A copy of Certificate of Incorporation (iii) A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company. (iv) All other documents in terms Para 10 of the Tender Form (Second Sheet) of IRSGCC April-2022.
(f) LLP (Limited Liability Partnership): (i)A copy of LLP Agreement (ii)A copy of Certificate of Incorporation (iii) A copy of Power of Attorney/Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP. (iv) An undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP or JV in which they were / are partners/members. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract. (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of IRSGCC April- 2022.
(g) Registered Society & Registered Trust: (i)A copy of Certificate of Registration (ii)A copy of Memorandum of Association of Society/Trust Deed (iii) A copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust. (iv) A copy of Rules & Regulations of the Society (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet) of IRSGCC April-2022.
Declaration regarding Retd Railway Employee.
PAN
GST REGISTRATION
EPF REGISTRATION (IF APPLICABLE)
Bid Security as Bank Guarantee Bond from a scheduled commercial bank of India . The Bank Guarantee Bond shall be as per Annexure VIA (AVAILABLE IN GCC APRIL 2022 WHICH IS UPLOADED IN DOCUMENT TAB) and shall be valid for a period of 90 days beyond the bid validity period. The original Bank Guarantee should be delivered to officials of Engineering Tender cell/ RNC, before closing date for submission of bids (i.e. excluding the last date of submission of bids). Non submission of scanned copy of Bank Guarantee with the bid on e-tendering portal (IREPS) and/or non submission of original Bank Guarantee within the specified period shall lead to summary rejection of bid. Bank Guarantee Bond should be with following details:-
1.15.1 Acting through - DRM(Engg.), South Eastern Railway, Ranchi.
Beneficiary: FA & CAO, South Eastern Railway, Garden Reach, 1.15.2 Kolkata.
Duly filled and signed Annexure VIB (AVAILABLE IN GCC APRIL 2022 WHICH IS UPLOADED IN DOCUMENT TAB) ) duly supported by Audited Balance Sheet duly certified by the Chartered Accountant. (for work costing more than 50 lakhs )
Technical Eligibility Criteria (for work costing more than 50 lakhs).
BID CAPACITY:- For tenders having advertised value more than Rs 10 crore.
Joint Venture (JV):- For tenders having advertised value more than Rs 10 crore.
Commercial-Compliance:-
Tenderer must have valid PF code number. Tenderer should upload document with respect to valid PF code number . Bill will be cleared only after verification of PF challan paid for previous month among all other statutory dues by the contractor/establishment.
Tenderers are required to upload copy of Permanent Account Number & GST.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Construction of an Operation & Traffic Control (Unified Command and Control Centre-UCCC) to function as an integrated command centre for all departments and branches involved in train operations at Ranchi Division, along with provision of additional built-up space at the DRM Office, Ranchi, to accommodate integrated operational facilities and allied administrative infrastructure.
DRMENGGRNC-67-2026~SER
DRMENGGRNC-67-2026
Open
Works - General
12 Months
Ranchi, Jharkhand
₹0
₹13.9 L
15 Aug 2026
15 Aug 2026
24 Aug 2026
120 items across 1 schedule · ₹6,26,22,397.35 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | All kinds of soil | cum | 152 | 177.5 | 26,980 |
| 2 | All kinds of soil. | cum | 640 | 260.3 | 1,66,592 |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. | cum | 400 | 196 | 78,400 |
| 4 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. | cum | 736 | 700.5 | 5,15,568 |
| 5 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. | cum | 352 | 2,123.75 | 7,47,560 |
| 6 | With Chlorpyriphos/Lindane E.C. 20% with 1% concentration | Sqm 2720 | — | 310.05 | 8,43,336 |
| 7 | 1:1 1/2:3 (1 Cement: 1 1/2 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 16 | 8,340.85 | 1,33,453.6 |
| 8 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 464 | 7,878.5 | 36,55,624 |
| 9 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 64 | 7,294.7 | 4,66,860.8 |
| 10 | 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 8 | 9,895.2 | 79,161.6 |
| 11 | Foundations, footings, bases for columns | Sqm | 192 | 392.15 | 75,292.8 |
| 12 | Foundations, footings, bases of columns, etc. for mass concrete | Sqm | 272 | 392.15 | 1,06,664.8 |
| 13 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. | Sqm | 48 | 842.5 | 40,440 |
| 14 | Suspended floors, roofs, landings, balconies and access platform | Sqm 3040 | — | 927.25 | 28,18,840 |
| 15 | Lintels, beams, plinth beams, girders, bressummers and cantilevers | Sqm 2960 | — | 736.4 | 21,79,744 |
| 16 | Columns, Pillars, Piers, Abutments, Posts and Struts | Sqm 1056 | — | 961.3 | 10,15,132.8 |
| 17 | Stairs, (excluding landings) except spiral- staircases | Sqm | 34 | 764.95 | 26,008.3 |
| 18 | Weather shade, Chajjas, corbels etc., including edges | Sqm | 96 | 951.1 | 91,305.6 |
| 19 | Thermo-Mechanically Treated bars of grade Fe-500D or more. | Kg 45600 | — | 107.85 | 49,17,960 |
| 20 | Thermo-Mechanically Treated bars of grade Fe-500D or more. | Kg 100800 | — | 107.85 | 1,08,71,280 |
| 21 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 304 | 9,504.75 | 28,89,444 |
| 22 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 672 | 9,860.4 | 66,26,188.8 |
| 23 | Add for using extra cement in the items of design mix over and above the specified cement content therein. | Quintal | 322 | 733.5 | 2,36,187 |
| 24 | Cement mortar 1:4 (1 cement : 4 coarse sand) | cum | 64 | 7,370.65 | 4,71,721.6 |
| 25 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 144 | 7,132.25 | 10,27,044 |
| 26 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 75 | 9,105.95 | 6,82,946.25 |
| 27 | Cement mortar 1:6 (1 cement : 6 Coarse sand) | cum | 32 | 8,752.55 | 2,80,081.6 |
| 28 | Providing and laying Gypsum panel partitions 100 mm thick with water proof Gypsum panels of size 666x500x100 mm, made of calcite phosphor Gypsum fixed with tongue and groove edges and jointed with bonding plaster as per manufacturer's specifications in superstructure above plinth level up to floor V level. Gypsum blocks will have a minimum compressive strength of 9.3 kg/cm2 | Sqm 1520 | — | 1,023.6 | 15,55,872 |
| 29 | Area of slab upto 0.50 sqm | Sqm | 19 | 5,413.5 | 1,02,856.5 |
| 30 | Area of slab over 0.50 sqm | Sqm | 29 | 5,136.3 | 1,48,952.7 |
| 31 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. | Sqm | 256 | 1,267.95 | 3,24,595.2 |
| 32 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. including:(a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design.(b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metallic colour of approved shades made out of 4 mm thick aluminium composite panel material consisting of 3 mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5 mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF /Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminium Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. | Sqm | 156 | 5,015.05 | 7,82,347.8 |
| 33 | Second class teak wood | cum | 3 | 1,42,949.7 | 4,28,849.1 |
| 34 | 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Sqm | 208 | 2,392.65 | 4,97,671.2 |
| 35 | On one side only | Sqm | 208 | 478 | 99,424 |
| 36 | 300x16 mm | Each | 48 | 216.55 | 10,394.4 |
| 37 | 250x16 mm | Each | 32 | 193.7 | 6,198.4 |
| 38 | 250x10 mm | Each | 48 | 83.9 | 4,027.2 |
| 39 | 150x10 mm | Each | 32 | 59.45 | 1,902.4 |
| 40 | 125 mm | Each | 48 | 39.95 | 1,917.6 |
| 41 | 75 mm | Each | 32 | 29.7 | 950.4 |
| 42 | 125x64x1.90 mm | Each | 48 | 118.2 | 5,673.6 |
| 43 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. | Each | 32 | 854.65 | 27,348.8 |
| 44 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. | Each | 80 | 1,124.85 | 89,988 |
| 45 | Twin rubber stopper | Each | 80 | 72.35 | 5,788 |
| 46 | Second class teak wood | Sqm | 19 | 5,217.65 | 99,135.35 |
| 47 | With 12 mm mild steel U beading | Sqm | 64 | 1,228 | 78,592 |
| 48 | Using R2 series with frame (70 mm & above) x (40 mm & above) & sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre). | Sqm | 64 | 8,748.35 | 5,59,894.4 |
| 49 | Using R3 series with frame (98 mm & above) x (40 mm & above) & sash (30 mm & above) x (55 mm & above) with zinc alloy (zamak) powder coated handle on two end panels along with multi-point locking system (Height upto 1.8 metre). | Sqm | 64 | 8,543.6 | 5,46,790.4 |
| 50 | Using R1 series with frame (33mm & above ) x (35mm & above). (Height upto 0.90 meter) | Sqm | 13 | 8,247.25 | 1,07,214.25 |
| 51 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. | Sqm | 13 | 11,439.6 | 1,48,714.8 |
| 52 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works | Kg 4560 | — | 172.6 | 7,87,056 |
| 53 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). | Kg | 640 | 772.4 | 4,94,336 |
| 54 | 1:6 (1cement : 6 coarse sand) | Sqm 2650 | — | 965.55 | 25,58,707.5 |
| 55 | 18 mm thick | Sqm | 320 | 662.05 | 2,11,856 |
| 56 | 25 mm thick | Sqm | 120 | 1,948.25 | 2,33,790 |
| 57 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. | Sqm | 20 | 2,354.7 | 47,094 |
| 58 | Size of Tile 600 x 600 mm | Sqm | 430 | 1,502.75 | 6,46,182.5 |
| 59 | Size of Tile 600 x 1200 mm | Sqm | 890 | 1,798.8 | 16,00,932 |
| 60 | Size of Tile 800 x 800 mm | Sqm | 352 | 1,728.8 | 6,08,537.6 |
| 61 | Size of Tile 600 x 600 mm | Sqm | 120 | 1,464.85 | 1,75,782 |
| 62 | Size of Tile 600x600 mm | Sqm | 304 | 1,623.05 | 4,93,407.2 |
| 63 | Providing and laying full body vitrified tile in floor of minimum thickness 15 mm with water absorption less than 0.06% and confirming to IS:15622, of approved make , brand and manufacturer , laid on 20 mm thick base cement mortar 1:4 (1 cement 4 coarse sand ) jointing with grey cement slurry @3.30 kg/sqm including grouting the joints with white cement and matching pigments etc. The slab must be cut with zero chipping diamond cutter only . Laying of slab will be done with the help of notch trowel , wedge , clips of required thickness , vacuum cups for lifting , leveling system and rubber mallet for placing the slab gently and easily. Size of tile 800 x2400 mm of all colors and shades | Sqm | 220 | 3,623.95 | 7,97,269 |
| 64 | Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent | Sqm | 128 | 4,481.3 | 5,73,606.4 |
| 65 | 75 mm diameter | Metre | 32 | 248.8 | 7,961.6 |
| 66 | 110 mm diameter | Metre | 128 | 377.4 | 48,307.2 |
| 67 | 75 mm | Each | 6 | 91.7 | 550.2 |
| 68 | 110 mm | Each | 13 | 136.15 | 1,769.95 |
| 69 | 75x75x75 mm | Each | 3 | 164.2 | 492.6 |
| 70 | 110x110x110 mm | Each | 26 | 234.15 | 6,087.9 |
| 71 | 75 mm bend | Each | 6 | 105.9 | 635.4 |
| 72 | 110 mm bend | Each | 51 | 150.35 | 7,667.85 |
| 73 | 110 mm Shoe | Each | 29 | 131.85 | 3,823.65 |
| 74 | 75 mm | Each | 10 | 369.85 | 3,698.5 |
| 75 | 110 mm | Each | 77 | 371.3 | 28,590.1 |
| 76 | 1:6 (1 cement: 6 fine sand) | Sqm 2480 | — | 333.35 | 8,26,708 |
| 77 | 1:6 (1 cement: 6 fine sand) | Sqm 1136 | — | 383 | 4,35,088 |
| 78 | 1:3 (1 cement : 3 fine sand) | Sqm 2690 | — | 300.45 | 8,08,210.5 |
| 79 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. | Sqm 5600 | — | 262.7 | 14,71,120 |
| 80 | New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm | Sqm | 385 | 223.6 | 86,086 |
| 81 | New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. | Sqm 1136 | — | 181.25 | 2,05,900 |
| 82 | Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture | Sqm | 144 | 226.25 | 32,580 |
| 83 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. | Sqm 1136 | — | 156.05 | 1,77,272.8 |
| 84 | Two coats | Sqm 5600 | — | 142.8 | 7,99,680 |
| 85 | With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre | Sqm 5600 | — | 73.95 | 4,14,120 |
| 86 | 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. | Sqm | 96 | 1,045.65 | 1,00,382.4 |
| 87 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests | Each | 8 | 6,767.4 | 54,139.2 |
| 88 | W.C. pan with ISI marked white solid plastic seat and lid | Each | 6 | 6,515.55 | 39,093.3 |
| 89 | One urinal basin with 5 litre white P.V.C. automatic flushing cistern | Each | 5 | 6,258.75 | 31,293.75 |
| 90 | White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps | Each | 13 | 2,301.75 | 29,922.75 |
| 91 | 510x1040 mm bowl depth 250 mm | Each | 3 | 6,945.6 | 20,836.8 |
| 92 | 40 mm dia | Each | 14 | 119.55 | 1,673.7 |
| 93 | Providing and fixing 100 mm sand cast Iron grating for gully trap. | Each | 13 | 53.25 | 692.25 |
| 94 | Rectangular shape 453x357 mm | Each | 6 | 1,361.8 | 8,170.8 |
| 95 | Rectangular shape 1500x450 mm | Each | 3 | 2,093 | 6,279 |
| 96 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. | Each | 3 | 231.95 | 695.85 |
| 97 | 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. | Each | 10 | 708.95 | 7,089.5 |
| 98 | Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms. | Each | 6 | 713.2 | 4,279.2 |
| 99 | 20 mm nominal dia Pipes | Metre | 30 | 335 | 10,050 |
| 100 | 25 mm nominal dia Pipes | Metre | 43 | 401.55 | 17,266.65 |
| 101 | 32 mm nominal dia Pipes | Metre | 74 | 518.75 | 38,387.5 |
| 102 | 20 mm nominal dia Pipes | Metre | 98 | 537.6 | 52,684.8 |
| 103 | 25 mm nominal dia Pipes | Metre | 43 | 627.25 | 26,971.75 |
| 104 | 32 mm nominal dia Pipes | Metre | 24 | 438.6 | 10,526.4 |
| 105 | 50 mm nominal dia Pipes | Metre | 74 | 794.25 | 58,774.5 |
| 106 | 65 mm nominal dia Pipes | Metre | 30 | 1,674.4 | 50,232 |
| 107 | 32 mm nominal bore. | Each | 24 | 689.6 | 16,550.4 |
| 108 | 100 mm diameter | Each | 6 | 193.95 | 1,163.7 |
| 109 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. | Per 8000 Litre | — | 11 | 88,000 |
| 110 | 15 mm nominal bore | Each | 24 | 506.8 | 12,163.2 |
| 111 | 15 mm nominal bore | Each | 8 | 820.7 | 6,565.6 |
| 112 | 15mm nominal bore | Each | 48 | 574.3 | 27,566.4 |
| 113 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in- charge. | Each | 30 | 74.8 | 2,244 |
| 114 | 100 mm nominal dia | Each | 13 | 37.6 | 488.8 |
| 115 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. | Each | 13 | 111.45 | 1,448.85 |
| 116 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 | Each | 3 | 26,861.9 | 80,585.7 |
| 117 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) | Sqm | 128 | 1,505.25 | 1,92,672 |
| 118 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in- charge (Door handle, lock and stopper etc. to paid separately) | Sqm | 19 | 5,325.9 | 1,01,192.1 |
| 119 | Frame size 50 x 100 mm | Metre | 88 | 947.7 | 83,397.6 |
| 120 | 30 mm thick | Sqm | 32 | 4,346.7 | 1,39,094.4 |
| Schedule total | ₹6,26,22,397.35 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCCACS12-12.08.2026.pdf
ATTACHMENT
GCCACS11_CompressPdf.pdf
ATTACHMENT
GCC - 2022 - ACS 10 - Updated
ATTACHMENT
BidSecurity-BGformat.pdf
ATTACHMENT
PG Format - Engg Ranchi New - Update
ATTACHMENT
ANNEXURE-VA.pdf
ATTACHMENT
Letter of Credit
ATTACHMENT
Telecom Circular 9-2023-New
ATTACHMENT
2018_CE-I_CT_9Date04_06_2018.pdf
ATTACHMENT
TelecomCircular9-2023-New.pdf
ATTACHMENT
GCC-2022-ACS10UpdatedC.pdf
ATTACHMENT
PGFormat-Engg.RanchiNew-21.11.2025.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].