Improvement of Water Supply Scheme to Laluwal, W SS Polian Beet and WSS Batt Kalan in tehsil Haroli Distt. Una (HP) Under Special Assistance (Sub Head P/L Rising mains, Supply and Errection of Pumping Machineries along with allied Civil work

Amount

Excavation in foundation and trenches up to all depths and in all classification of earth work such as Pick work, Jumper work, chiselling or wedging out of soft and hard rock as blasting is prohibited, saturated soil including bailing or pumping out of water, including cutting of bitumenous/concrete surface wherever required, in all lifts including trimming and dressing of sides, levelling of beds to correct grade including shoring, strutting , planking, timbering and dewatering where ever required. Stacking usable and unusable material /soil seperataly and after laying, jointing and testing of pipes (for pipes, Pipe duct, chambers, x-sings etc.), returning the usable soil in 15cm layers by ramming and watering and then disposing of all surplus excavated soil/ unusable material as directed within all leads/ lifts and including cost of diversion for traffic, night signal boards, fixing caution boards, crossing over trenches for access to houses, fencing etc. complete in all respects within all leads and lifts as per direction of the Engineer-in-charge.

Pdg, Laying,Jointing and Testing in trenches Galvanized mild steel flanged/butt welded pipe of below mentioned dia and grade conforming to IS 1239-2004 (with latest ammendments The M.S. flanges are to be provided 1% of total joints as per table below conforming to 6392-1971 ( Latest uptodate ammendments) and welding of M.S. flanges with pipe as per IS: 816-1965 with electrode as per IS: 814-1967 including required Nos. and size of M.S. nuts and bolts as per IS: 1369-1967 and compressed asbestos fibre jointing gaskets sheet not less than 3mm thick as per IS: 27121-1965. The welding of flanges to be done on both faces in three layers in each face to make the joints leak proof including all kind of specials such as bends of all degree to be made from parent tube, short pieces, tail pieces all made from parent tube and to the entire satisfaction of enginer-in-charge. The pipes end should be bevelled suitable for butt welding. The circumferencial butt welded joints ( 99% of the total joints) by electrical arc welding to following dia & class pipes,welding of pipes to be done in three layers to make the joints leak proof and to achieve the minimum effective throat thickness of weld conforming to IS- 816-1969 specifications, by using welding electrodes of 2.5 mm to 6.3 mm of Advani oerlikon (Adore)-CITOJET/ESAB make, conforming to IS 814-1991, at site of work complete in all respects and including DPT test for joints & manual/mechnical handing of pipes. The laying of pipe shall confirm to BIS-5822 (with latest ammendments uptodate), including all kind of specials such as bends of all degree to be made from parent tube, short pieces, tail pieces all made from parent tube within all leads and lifts. ( Earth work in trenches, M.S. flanges and butt welded joints to be measured and paid for separately)

125mm dia GMS (M) IS 1239-2004

100mm dia GMS (M) IS 1239-2004

Providing and welding M.S. flanges @1% at suitable point, conforming to following tables as per IS: 6392-1971 (Latest with upto date amendments) with plain end GMS/MSERW pipe in requsite number of layers on both faces to make the joint leak proof (The cost of providing and laying of MSERW pipes to be measured and paid for seprately). The welding of flanges should conform to IS:816-1969 with electrodes as per IS: 814-1991 and required number of nuts and bolts conforming to IS 1364. including cost of gasket sheet nuts & bolts. The thickness of gasket sheet not less then 3.00 mm conforming to IS 2712-1998. The work shall be done to the entire satifaction of engineer in charge with in all leads and lifts.tion of Engineer-in-Charge.

125mm dia T-5

100mm dia T-5

Providing circumferential butt welded joints @99% by electrical arc welding to GMS pipe, welded in requisite number of weld runs so as to achieve the minimum effective throat thickness of weld conforming to IS 816-1969 specifications, by using welding electrodes of 2.5mm to 6.3mm of Advani Oerilikon (Adore)-CITOJET/ES/ESAB make,conforming to IS 814-1991, include Die pentration test,at site of work complete in all respects, including manual/mechanical handling of pipes in all leads and lifts to the entire satisfaction of Engineer-in-Charge.

125mm dia

100mm dia

WSS Laluwal: Supply of submersible pumping set of reputed make such as KSB/ Calama / BS/ Worthigton / Sabar/ Seerex /Johnston / Amrut/ lubi/ Hindustan/Groundfos /Kirloskar confirming to latest relevent BIS . The pump should be fitted with free fine impellers of suitable alloys as per BIS ; 5659-1978 with upto date amendments, suitable for raw / clear water having greased packed bearing and shell with wound stator on motor side and with shaft protection on pump side ensuring better life for shaft conforming to BIS specifications. The pump shall be directly coupled to submersible motor of same as that of offered submersible pump make confirming to BIS ;9283-1979 with upto date amendments, totally dust and water proof for submersible pump, duly isolated from the pump by intermediate casing with double mechanical seal in oil chamber and grease packed, lubricated bearing and provided with stainless steel thrust bearing plate to withstand non vertical loads with minimum wear tear.It should also be fitted with a device to make up expantion of water with heating of motor. The pumpset should include water level guard i/c cable ,errection clamps, cable clips and depth gauge etc. and suitable for opertion on data given below. a Pumps :- Specifications i) Make ii) Model iii) No. of stages iv) Manufacter's certificate to be attached Performance i) Discharge ii) Head iii) Efficiency of Pump a) Duty Head b) (+) 10% Duty Head. c) (-) 15% Duty Head d) Performance curve to be attached b) Motors; Specification i) Make ii) Model iii) B.H.P iv) Speed v) Insulation a Pumps :- Specifications i) Make ii) Model iii) No. of stages iv) Manufacter's certificate to be attached Performance i) Discharge ii) Head iii) Efficiency of Pump a) Duty Head b) (+) 10% Duty Head. c) (-) 15% Duty Head d) Performance curve to be attached b) Motors; Specification i) Make ii) Model iii) B.H.P iv) Speed v) Insulation

Discharge, (Q) 16.13 LPS

Total Head ( H ) 176.75 Mts.

a) SWL in Tubewell =0.00 Mtr. bgl.

c) R.L. point of discharge = 266.20Mtr.

d) Seasonal fluctuation + draught condition + bowl assembly. 9.0 Mtrs.

e) Drawdown in Tubewell Mtrs.

f) R.L of lowest point of pumpset installation = 92.62 Mtrs.

g) Static Column lift = Mtrs.

Rising main. Column Pipe.

Length 20 Mtrs. Length 185 mtrr.

Dia meter 150 mm Dia 125 mm

Class GMS ( M) Class GMS. (M)

Pumping hours 8 hours

Altitude of installations above M.S.L. __________mtr.

Characteristic of water.

a) Temperature _______ Deg Cel.

b) Turbidity ________JTU.

c) Allkanity. ___________mg/ l Ca Co3

d) Size of solids ____________mm

e) others

Depth of T/well mtr.

Dia of T/ well assembly 200 mm.

Length of assembly pipe.

Dia of housing pipe 300 mm.

Length of housing pipe

OPERATING CONDITIONS.

Type of Current :- A.C.Three Phase.

Frequency:- 50 Cycles /Sec.

Rated Voltage 415 +/- 15 % Volts.

System of earthing: Double Loop earthing as per BIS 3843-1987 Latest.

Speed of Revolution ____________ RPM 2900

MOTOR.

Ref. to BIS code BIS 9283-1979 with upto date amendments.

Type of enclosure of motor: As per BIS ; 4691-1985 ( latest )

Mechanical out put in H.P.

Class of insulation :Class B

The motor should be able to withstand initial current of 2.50 times the rated current for two minutes without suffering damages of permanent deformations.

Ref. to BIS code ; BIS ; 5659-1978 with upto date amendments.

Drive Type: Electric driven.

Operating Range: -15 % to+10 % of Total head at duty point.

Deliver size of Pump : ________( To be quoted by tenderer.)

Providing ICTP Main Switch with HRC fuses of L&T/ Havells /Standard/ Kilburn Siemens make and having capacity 30% extra of the operational rating as per IS : 13947-P I & II with upto date amendments.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type ) switch board including angle iron post of suitable height and size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising and capable of mounting the following accessories with all internal connections. .

a) OCB of kilburn / L&T/ Havells/Standard make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. i) Make : ii) Type : iii) Capacity :

ii) ELCB of recommended make L&T / Havells as per IS ; 2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. i) Make : ii) Type : iii) Capacity :

iii) The voltage monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage,reverse phasing,overloading and phase voltage difference as per IS; 3842 ( Latest Edition )

d) Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ;8084-1976 and IS :11353-1985 read with BIS ; 5578 -1985 with upto date amendments including.

Three phase indicator lamps complete with toggle switches for indivual motors as per IS 3452 ( P- I&II ) with upto date amendments.

e) Capacitor of BHEL / GEC / L&T / Mecheil make as per IS ; 2834-1968 with upto date amendments,to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter / IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB. i) Make : ii) Type : iii) Capacity :

Providing suitable starter of L&T /BHEL make as per IS : 13947-II with upto date 'amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic type over load release and dashpot, time lag, under voltage release, with or without initial oil filling as the case may be with single phase preventor as per IS ;1248 ( P-V ) 1983 with up to date amendments.

Providing and fixing double flanged Cast Iron Sluice valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make for the Column pipe of pump and capable of withstanding the normal seat pressure and as per IS 780-1992 with latest ammendments Class PN 1.00 For Column Pipe 125 mm dia PN 1.6

Providing and fixing double flanged Cast Iron Reflux valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make having by pass arrangement on the delivery line of pump and capable of withstanding the normal seat pressure and as per IS 6312-1984 P-I with latest ammendments 150 mm dia PN 1.6

Providing and fixing pressure gauge of Prega / Precision / Fiebig make complete with all accessories such as stop cock, copper tubing as per IS ; 3624-1987 with upto date amendements

Supply of PVC jointless,flat water proof cable with copper conductor as per BIS 694-1998 latest with upto date ammendments of Havelles/Finolex make suitable for the pumpsets offered from OCB to motor including all other electrical equipments / accessories such as thimble, flexible pipe,solder, nuts and bolts, cable glands, clips etc, laid in pipes or trenches under floor.The type, size and make shall be subject to approval of HPSEB authorities.

Pdg & lowering of GMS Column pipe for assembly 125 mm dia including MS flanges' of Table 17 as per IS : 6392-1971 with upto date amendments, rubber / asbestos gasket of min.3 mm thickness as per IS 2712-1979 and required numbers of nuts and bolts as per IS ;1364-1983 .The Column pipe shall be as per relevent IS Code and to withstand 1.50 times total head stipulated under item No.5 . The Column pipe should be extended upto 5 mtr. beyond the outer wall of the pump house in the direction of Rising main .The Column pipe should be properly jointed with the Rising main including all necessary accessories like increaser / reducer, flanges, bends etc, including supporting clamps (2 Each) at the top of T/well assembly, and as per the direction of Engineer - in - Charge.( The pipe shall be supplied by the department free of cost from Divisional store Malahat )

Installation of all items appearing as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor.

Providing and fixing double loop earthing with GI plate of 20x3 mm thick electrode complete with material such as thimble, nuts and bolts, charcoal, salt 25x5 mm strip as per IS ; 3043-1987 with upto date amendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the dirction of the Engineer - in - Charge.

Collection tank to storage tank Stage 1 (WSS Laluwal): Providing horizontal spindle, horizontal / radial split casing /end suction ( back pull out arrange-ment) Single /double /multi stage of Kirloskar / KSB Crupton KSB/Calama/BS/ Groundfos/ Hindustan/ Lubbi make as per BIS IS 1520-1980 with upto date ammendments read with IS: 9137-1978 or latest edition suitable for lifting water for under mentioned characteristic with Bronze impellers / priming funnels, casing ring and shaft sleeves of Bronze shaft of stainless steel with cast iron casing, coupled directly through a flexible coupling on a common cast iron / cast steel base plate (base plate to be framed from the manufacturers of the pumping unit only) to slipring / Squirrel cage screen protected drip proof induction motor / motors of standard make such as Crompton / NGEF / GEC / Seimens /Jyoti/ Kirloskar BHEL / ABB suitable for operation on 415 (+/-15%) volts. 50 Cycles /Sec. 3 phase AC electric supply of 2900 RPM.The power of electric motor/ motors should be at least +10% in excess of the maximum power required by the pump / pumps in the Operation range of (+10%) and (-15%) of the duty point head. The motor / motors as per IS 325 IS -1978 with upto date amendments read with IS 900 -1972. It should include cost of Bearing. Nuts, Bolts and painting etc. and should meet the following requirements. (a) Pump :- Specifications i) Make ii) Model iii) No. of stages iv) Manfacurer's certificate to be attached. performance i) Discharge ii) head Make ii) Model iii) efficiency of pump a) duty Head b) (+) 10% duty head c). (-) 15% Duty Head d) performance curve to be attached b). Motors:- Specificions Make ii) Model iii) Rating iv). speed v) Insulation (C) Coupling (D) Base plate

Discharge =( Q) 9.84 LPS

Total Head = ( H) 44.95 Mts.

a) LWL In clear water Tank = 263.20 mtr

b) R.L. of shaft = 263.20 Mtrs.

c) R.L. of discharge Point. = 302.00 mtrs.

d) Suction lift. +tive mtrs.

e) Discharge Head =302.00 mtrs.

f) Static Head = 38.80 mtrs.

Rising main.

Length = 250 mtrs.

Diameter = 125mm. Dia GMS pipe

Class GMS Tube (MG)

Pumping hours. 8 hours.

Altitude of installations above M.S.L 407 mtrs.

Characteristic of Water

a)Temperature ___20_____Deg.Col.

b)Turbidity ________ JTU

c) Alloanity _________ mg/1 ca Co3

d)Size of solids __________ mm

e) Others.

(a) Pumps: Specifications:

i)Make

ii)Model.

iii)No.of stages:-

iv)Manufacturers

certificate to be attached.

Performance

i)Discharge:-

ii)Total Head:-

iii)B.H.P.

iv)Efficiency:

vi)Performance Curve to be attached.

b)Motors: Specifications.

i)Make

ii)Model

iii)Rating

iv)Speed.

v)Insulation.

(C) Coupling:

(d) Base Plate.

Providing ICTP Main Switch with HRC fuses of L&T/ Havells/ Standard / Kilburn / Siemens make and having capacity 30% extra of the operational rating as per IS : 13947-P I & II with upto date amendments.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type ) switch board i/c angle iron post of suitable height & size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising & capable of mounting the following accessories with all internal connections.

MCB of kilburn / L&T / Havells / Standard make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. i) Make : ii) Type : iii) Capacity :

ELCB of recommended make L&T Havells / Standard / Kilburn as per IS ;2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. i) Make : ii) Type : iii) Capacity :

The Voltage Monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage, reverse phasing, overloading and phase voltage difference as per IS; 3842 ( Latest Edition )

Power factor meter of standard make as per relevent IS code with upto date ammendments.

Frequency meter of standard make as per relevent IS code with upto date ammendments.

d) Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ;8084-1976 and IS :11353-1985 read with BIS ; 5578 -1985 with upto date amendments.

Three phase indicator lamps complete with toggle switches for indivual motors as per IS 3452 ( P- I&II ) with upto date amendments.

Capacitor of BHEL / GEC / L&T / Mecheil make as per IS ; 2834-1968 with upto date amendments,to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter / IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB. i) Make : ii) Type : iii) Capacity :

Providing suitable starter of L&T /BHEL make as per IS : 13947-II with upto date 'amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic type over load release and dashpot, time lag, under voltage release, with or without initial oil filling as the case may be with single phase preventor as per IS ;1248 ( P-V ) 1983 with up to date amendments.

Providing & fixing double flanged Cast Iron Sluice valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of suction pipe of pump and capable of with standing normal Seat Pressure as per IS 14846 with upto date ammendments. 125mm dia Class PN 1.00

Providing and fixing double flanged Cast Iron Sluice valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of 100 mm dia for the delivery line of pump and capable of with standing normal Seat Pressure as per IS 14846 with upto date ammendments. Class PN 1.00

Providing double flanged swing type cast iron Reflux Valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of 125 mm dia having Bye pass arrangement on the delivery line of the of the Pump and capable of withstanding normal Seat Pressure as per IS :5312-1984 (P-I) (Cast Iron) with latest ammendments

Providing and fixing circular dial pressure gauge of Precision / Fiebig make complete with all accessories such as stop cock,Copper tubing etc.as per IS: 3624-1987 with upto date ammendments.

Installation of all items appearing as above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and Fixing double flanged GMS/GMSERW piping work ( Layout to be approved by Engineer-in-Charge). for suction and delivery pipes suitable to pumps offered and common header as per the rising main respectively complete with all specials such as bends,Tees, Reducers / Inceasers with companion flanges matching with the relevant specifications of the accessories as indicated in the Drawing including rubber / asbestos gasket of 3 mm thickness as per IS : 2712-1972 and required number of Nuts and Bolts as per 1364-1983.-the pipes shall be as per relevent IS code and to withstand 1.50 times total head.

i) Suction Pipe 125 mm dia.

ii) Delivery Pipe 100 mm dia.

iii) Common Header 125 mm dia. and will extend upto 5 metres from the outer wall of the pump house in the direction of Rising main to be joined.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor.

Storage tank Stage I to Storage tank Stage II (WSS Laluwal): Providing horizontal spindle, horizontal / radial split casing /end suction ( back pull out arrange-ment) Single /double /multi stage of Kirloskar / KSB Crupton KSB/Calama/BS/ Groundfos/ Hindustan/ Lubbi make as per BIS IS 1520-1980 with upto date ammendments read with IS: 9137-1978 or latest edition suitable for lifting water for under mentioned characteristic with Bronze impellers / priming funnels, casing ring and shaft sleeves of Bronze shaft of stainless steel with cast iron casing, coupled directly through a flexible coupling on a common cast iron / cast steel base plate (base plate to be framed from the manufacturers of the pumping unit only) to slipring / Squirrel cage screen protected drip proof induction motor / motors of standard make such as Crompton / NGEF / GEC / Seimens /Jyoti/ Kirloskar BHEL / ABB suitable for operation on 415 (+/-15%) volts. 50 Cycles /Sec. 3 phase AC electric supply of 2900 RPM.The power of electric motor/ motors should be at least +10% in excess of the maximum power required by the pump / pumps in the Operation range of (+10%) and (-15%) of the duty point head. The motor / motors as per IS 325 IS -1978 with upto date amendments read with IS 900 -1972. It should include cost of Bearing. Nuts, Bolts and painting etc. and should meet the following requirements. (a) Pump :- Specifications i) Make ii) Model iii) No. of stages iv) Manfacurer's certificate to be attached. performance i) Discharge ii) head Make ii) Model iii) efficiency of pump a) duty Head b) (+) 10% duty head c). (-) 15% Duty Head d) performance curve to be attached b). Motors:- Specificions Make ii) Model iii) Rating iv). speed v) Insulation (C) Coupling (D) Base plate

Discharge =( Q) 7.62 LPS

Total Head = ( H) 97.09 Mts.

a) LWL In clear water Tank = 299.11 mtr

b) R.L. of shaft = 299.11 Mtrs.

c) R.L. of discharge Point. = 352.85 mtrs.

d) Suction lift. +tive mtrs.

e) Discharge Head =352.85 mtrs.

f) Static Head = 53.74 mtrs.

Rising main.

Length = 2010 mtrs.

Diameter = 100mm. Dia GMS pipe

Class GMS Tube (MG)

Pumping hours. 8 hours.

Altitude of installations above M.S.L 407 mtrs.

Characteristic of Water

a)Temperature ___20_____Deg.Col.

b)Turbidity ________ JTU

c) Alloanity _________ mg/1 ca Co3

d)Size of solids __________ mm

e) Others.

(a) Pumps: Specifications:

i)Make

ii)Model.

iii)No.of stages:-

iv)Manufacturers

certificate to be attached.

Performance

i)Discharge:-

ii)Total Head:-

iii)B.H.P.

iv)Efficiency:

vi)Performance Curve to be attached.

b)Motors: Specifications.

i)Make

ii)Model

iii)Rating

iv)Speed.

v)Insulation.

(C) Coupling:

(d) Base Plate.

Providing ICTP Main Switch with HRC fuses of L&T/ Havells/ Standard / Kilburn / Siemens make and having capacity 30% extra of the operational rating as per IS : 13947-P I & II with upto date amendments.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type ) switch board i/c angle iron post of suitable height & size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising & capable of mounting the following accessories with all internal connections.

MCB of kilburn / L&T / Havells / Standard make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. i) Make : ii) Type : iii) Capacity :

ELCB of recommended make L&T Havells / Standard / Kilburn as per IS ;2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. i) Make : ii) Type : iii) Capacity :

The Voltage Monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage, reverse phasing, overloading and phase voltage difference as per IS; 3842 ( Latest Edition )

Power factor meter of standard make as per relevent IS code with upto date ammendments.

Frequency meter of standard make as per relevent IS code with upto date ammendments.

d) Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ;8084-1976 and IS :11353-1985 read with BIS ; 5578 -1985 with upto date amendments.

Three phase indicator lamps complete with toggle switches for indivual motors as per IS 3452 ( P- I&II ) with upto date amendments.

Capacitor of BHEL / GEC / L&T / Mecheil make as per IS ; 2834-1968 with upto date amendments,to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter / IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB. i) Make : ii) Type : iii) Capacity :

Providing suitable starter of L&T /BHEL make as per IS : 13947-II with upto date 'amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic type over load release and dashpot, time lag, under voltage release, with or without initial oil filling as the case may be with single phase preventor as per IS ;1248 ( P-V ) 1983 with up to date amendments.

Providing & fixing double flanged Cast Iron Sluice valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of suction pipe of pump and capable of with standing normal Seat Pressure as per IS 14846 with upto date ammendments. 100mm dia Class PN 1.00

Providing and fixing double flanged Cast Iron Sluice valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of 80 mm dia for the delivery line of pump and capable of with standing normal Seat Pressure as per IS 14846 with upto date ammendments. Class PN 1.00

Providing double flanged swing type cast iron Reflux Valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of 80 mm dia having Bye pass arrangement on the delivery line of the of the Pump and capable of withstanding normal Seat Pressure as per IS :5312-1984 (P-I) (Cast Iron) with latest ammendments

Providing double flanged swing type cast iron Reflux Valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of 100 mm dia having Bye pass arrangement on the rising main of the of the Pump and capable of withstanding normal Seat Pressure as per IS :5312-1984 (P-I) (Cast Iron) with latest ammendments

Providing and fixing circular dial pressure gauge of Precision / Fiebig make complete with all accessories such as stop cock,Copper tubing etc.as per IS: 3624-1987 with upto date ammendments.

Installation of all items appearing as above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and Fixing double flanged GMS/GMSERW piping work ( Layout to be approved by Engineer-in-Charge). for suction and delivery pipes suitable to pumps offered and common header as per the rising main respectively complete with all specials such as bends,Tees, Reducers / Inceasers with companion flanges matching with the relevant specifications of the accessories as indicated in the Drawing including rubber / asbestos gasket of 3 mm thickness as per IS : 2712-1972 and required number of Nuts and Bolts as per 1364-1983.-the pipes shall be as per relevent IS code and to withstand 1.50 times total head.

i) Suction Pipe 100 mm dia.

ii) Delivery Pipe 80 mm dia.

iii) Common Header 100 mm dia. and will extend upto 5 metres from the outer wall of the pump house in the direction of Rising main to be joined.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor.

Collection Tank to Storage tank Chhetran (WSS Laluwal): Providing horizontal spindle, horizontal / radial split casing /end suction ( back pull out arrange-ment) Single /double /multi stage of Kirloskar / KSB Crupton KSB/Calama/BS/ Groundfos/ Hindustan/ Lubbi make as per BIS IS 1520-1980 with upto date ammendments read with IS: 9137-1978 or latest edition suitable for lifting water for under mentioned characteristic with Bronze impellers / priming funnels, casing ring and shaft sleeves of Bronze shaft of stainless steel with cast iron casing, coupled directly through a flexible coupling on a common cast iron / cast steel base plate (base plate to be framed from the manufacturers of the pumping unit only) to slipring / Squirrel cage screen protected drip proof induction motor / motors of standard make such as Crompton / NGEF / GEC / Seimens /Jyoti/ Kirloskar BHEL / ABB suitable for operation on 415 (+/-15%) volts. 50 Cycles /Sec. 3 phase AC electric supply of 2900 RPM.The power of electric motor/ motors should be at least +10% in excess of the maximum power required by the pump / pumps in the Operation range of (+10%) and (-15%) of the duty point head. The motor / motors as per IS 325 IS -1978 with upto date amendments read with IS 900 -1972. It should include cost of Bearing. Nuts, Bolts and painting etc. and should meet the following requirements. (a) Pump :- Specifications i) Make ii) Model iii) No. of stages iv) Manfacurer's certificate to be attached. performance i) Discharge ii) head Make ii) Model iii) efficiency of pump a) duty Head b) (+) 10% duty head c). (-) 15% Duty Head d) performance curve to be attached b). Motors:- Specificions Make ii) Model iii) Rating iv). speed v) Insulation (C) Coupling (D) Base plate

Discharge =( Q) 6.29 LPS

Total Head = ( H) 58.08 Mts.

a) LWL In clear water Tank = mtr

b) R.L. of shaft = 263.20 Mtrs.

c) R.L. of discharge Point. = 313.20 mtrs.

d) Suction lift. +tive mtrs.

e) Discharge Head =313.20 mtrs.

f) Static Head = 50.00 mtrs.

Rising main.

Length = 330 mtrs.

Diameter = 100mm. Dia GMS pipe

Class GMS Tube (MG)

Pumping hours. 8 hours.

Altitude of installations above M.S.L 407 mtrs.

Characteristic of Water

a)Temperature ___20_____Deg.Col.

b)Turbidity ________ JTU

c) Alloanity _________ mg/1 ca Co3

d)Size of solids __________ mm

e) Others.

(a) Pumps: Specifications:

i)Make

ii)Model.

iii)No.of stages:-

iv)Manufacturers

certificate to be attached.

Performance

i)Discharge:-

ii)Total Head:-

iii)B.H.P.

iv)Efficiency:

vi)Performance Curve to be attached.

b)Motors: Specifications.

i)Make

ii)Model

iii)Rating

iv)Speed.

v)Insulation.

(C) Coupling:

(d) Base Plate.

Providing ICTP Main Switch with HRC fuses of L&T/ Havells/ Standard / Kilburn / Siemens make and having capacity 30% extra of the operational rating as per IS : 13947-P I & II with upto date amendments.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type ) switch board i/c angle iron post of suitable height & size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising & capable of mounting the following accessories with all internal connections.

MCB of kilburn / L&T / Havells / Standard make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. i) Make : ii) Type : iii) Capacity :

ELCB of recommended make L&T Havells / Standard / Kilburn as per IS ;2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. i) Make : ii) Type : iii) Capacity :

The Voltage Monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage, reverse phasing, overloading and phase voltage difference as per IS; 3842 ( Latest Edition )

Power factor meter of standard make as per relevent IS code with upto date ammendments.

Frequency meter of standard make as per relevent IS code with upto date ammendments.

d) Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ;8084-1976 and IS :11353-1985 read with BIS ; 5578 -1985 with upto date amendments.

Three phase indicator lamps complete with toggle switches for indivual motors as per IS 3452 ( P- I&II ) with upto date amendments.

Capacitor of BHEL / GEC / L&T / Mecheil make as per IS ; 2834-1968 with upto date amendments,to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter / IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB. i) Make : ii) Type : iii) Capacity :

Providing suitable starter of L&T /BHEL make as per IS : 13947-II with upto date 'amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic type over load release and dashpot, time lag, under voltage release, with or without initial oil filling as the case may be with single phase preventor as per IS ;1248 ( P-V ) 1983 with up to date amendments.

Providing & fixing double flanged Cast Iron Sluice valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of suction pipe of pump and capable of with standing normal Seat Pressure as per IS 14846 with upto date ammendments. 125mm dia Class PN 1.00

Providing and fixing double flanged Cast Iron Sluice valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of 100 mm dia for the delivery line of pump and capable of with standing normal Seat Pressure as per IS 14846 with upto date ammendments. Class PN 1.00

Providing double flanged swing type cast iron Reflux Valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of 125 mm dia having Bye pass arrangement on the delivery line of the of the Pump and capable of withstanding normal Seat Pressure as per IS :5312-1984 (P-I) (Cast Iron) with latest ammendments

Providing and fixing circular dial pressure gauge of Precision / Fiebig make complete with all accessories such as stop cock,Copper tubing etc.as per IS: 3624-1987 with upto date ammendments.

Installation of all items appearing as above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and Fixing double flanged GMS/GMSERW piping work ( Layout to be approved by Engineer-in-Charge). for suction and delivery pipes suitable to pumps offered and common header as per the rising main respectively complete with all specials such as bends,Tees, Reducers / Inceasers with companion flanges matching with the relevant specifications of the accessories as indicated in the Drawing including rubber / asbestos gasket of 3 mm thickness as per IS : 2712-1972 and required number of Nuts and Bolts as per 1364-1983.-the pipes shall be as per relevent IS code and to withstand 1.50 times total head.

i) Suction Pipe 125 mm dia.

ii) Delivery Pipe 100 mm dia.

iii) Common Header 125 mm dia. and will extend upto 5 metres from the outer wall of the pump house in the direction of Rising main to be joined.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor.

WSS Polian Beet: Supply of submersible pumping set of reputed make such as KSB/ Calama / BS/ Worthigton / Sabar/ Seerex /Johnston / Amrut/ lubi/ Hindustan/Groundfos confirming to latest relevent BIS . The pump should be fitted with free fine impellers of suitable alloys as per BIS ; 5659-1978 with upto date amendments, suitable for raw / clear water having greased packed bearing and shell with wound stator on motor side and with shaft protection on pump side ensuring better life for shaft conforming to BIS specifications. The pump shall be directly coupled to submersible motor of same as that of offered submersible pump make confirming to BIS ;9283-1979 with upto date amendments, totally dust and water proof for submersible pump, duly isolated from the pump by intermediate casing with double mechanical seal in oil chamber and grease packed, lubricated bearing and provided with stainless steel thrust bearing plate to withstand non vertical loads with minimum wear tear.It should also be fitted with a device to make up expantion of water with heating of motor. The pumpset should include water level guard i/c cable ,errection clamps, cable clips and depth gauge etc. and suitable for opertion on data given below. a Pumps :- Specifications i) Make ii) Model iii) No. of stages iv) Manufacter's certificate to be attached Performance i) Discharge ii) Head iii) Efficiency of Pump a) Duty Head b) (+) 10% Duty Head. c) (-) 15% Duty Head d) Performance curve to be attached b) Motors; Specification i) Make ii) Model iii) B.H.P iv) Speed v) Insulation

Discharge, (Q) 9.39 LPS

Total Head ( H ) 206.17 Mts.

a) SWL in Tubewell =0.00 Mtr. bgl.

c) R.L. point of discharge = 550.23Mtr.

d) Seasonal fluctuation + draught condition + bowl assembly. 9.0 Mtrs.

e) Drawdown in Tubewell Mtrs.

f) R.L of lowest point of pumpset installation = 349.23 Mtrs.

g) Static Column lift = Mtrs.

Rising main. Column Pipe.

Length 20 Mtrs. Length 198 mtrr.

Dia meter 125 mm Dia 125 mm

Class GMS ( M) Class GMS. (M)

Pumping hours 8 hours

Altitude of installations above M.S.L. __________mtr.

Characteristic of water.

a) Temperature _______ Deg Cel.

b) Turbidity ________JTU.

c) Allkanity. ___________mg/ l Ca Co3

d) Size of solids ____________mm

e) others

Depth of T/well mtr.

Dia of T/ well assembly 200 mm.

Length of assembly pipe.

Dia of housing pipe 300 mm.

Length of housing pipe

OPERATING CONDITIONS.

Type of Current :- A.C.Three Phase.

Frequency:- 50 Cycles /Sec.

Rated Voltage 415 +/- 15 % Volts.

System of earthing: Double Loop earthing as per BIS 3843-1987 Latest.

Speed of Revolution ____________ RPM 2900

MOTOR.

Ref. to BIS code BIS 9283-1979 with upto date amendments.

Type of enclosure of motor: As per BIS ; 4691-1985 ( latest )

Mechanical out put in H.P.

Class of insulation :Class B

The motor should be able to withstand initial current of 2.50 times the rated current for two minutes without suffering damages of permanent deformations.

Ref. to BIS code ; BIS ; 5659-1978 with upto date amendments.

Drive Type: Electric driven.

Operating Range: -15 % to+10 % of Total head at duty point.

Deliver size of Pump : ________( To be quoted by tenderer.)

Providing ICTP Main Switch with HRC fuses of L&T/ Havells /Standard/ Kilburn Siemens make and having capacity 30% extra of the operational rating as per IS : 13947-P I & II with upto date amendments.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type ) switch board including angle iron post of suitable height and size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising and capable of mounting the following accessories with all internal connections. .

a) MCB of kilburn / L&T/ Havells/Standard make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. i) Make : ii) Type : iii) Capacity :

ii) ELCB of recommended make L&T / Havells as per IS ; 2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault.

iii) The voltage monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage,reverse phasing,overloading and phase voltage difference as per IS; 3842 ( Latest Edition )

d) Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ;8084-1976 and IS :11353-1985 read with BIS ; 5578 -1985 with upto date amendments including.

Three phase indicator lamps complete with toggle switches for indivual motors as per IS 3452 ( P- I&II ) with upto date amendments.

e) Capacitor of BHEL / GEC / L&T / Mecheil make as per IS ; 2834-1968 with upto date amendments,to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter / IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB.

Providing suitable starter of L&T /BHEL make as per IS : 13947-II with upto date 'amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic type over load release and dashpot, time lag, under voltage release, with or without initial oil filling as the case may be with single phase preventor as per IS ;1248 ( P-V ) 1983 with up to date amendments.

Providing and fixing double flanged Cast Iron Sluice valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make for the Column pipe of pump and capable of withstanding the normal seat pressure and as per IS 780-1992 with latest ammendments Class PN 1.00 For Column Pipe 125 mm dia PN 1.6

Providing and fixing double flanged Cast Iron Reflux valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make having by pass arrangement on the delivery line of pump and capable of withstanding the normal seat pressure and as per IS 6312-1984 P-I with latest ammendments 125 mm dia PN 1.6

Providing and fixing pressure gauge of Prega / Precision / Fiebig make complete with all accessories such as stop cock, copper tubing as per IS ; 3624-1987 with upto date amendements

Supply of PVC jointless,flat water proof cable with copper conductor as per BIS 694-1998 latest with upto date ammendments of Havelles/Finolex make suitable for the pumpsets offered from OCB to motor including all other electrical equipments / accessories such as thimble, flexible pipe,solder, nuts and bolts, cable glands, clips etc, laid in pipes or trenches under floor.The type, size and make shall be subject to approval of HPSEB authorities.

Pdg & lowering of GMS Column pipe for assembly 125 mm dia including MS flanges' of Table 17 as per IS : 6392-1971 with upto date amendments, rubber / asbestos gasket of min.3 mm thickness as per IS 2712-1979 and required numbers of nuts and bolts as per IS ;1364-1983 .The Column pipe shall be as per relevent IS Code and to withstand 1.50 times total head stipulated under item No.5 . The Column pipe should be extended upto 5 mtr. beyond the outer wall of the pump house in the direction of Rising main .The Column pipe should be properly jointed with the Rising main including all necessary accessories like increaser / reducer, flanges, bends etc, including supporting clamps (2 Each) at the top of T/well assembly, and as per the direction of Engineer - in - Charge.( The pipe shall be supplied by the department free of cost from Divisional store Malahat )

Installation of all items appearing as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor.

Providing and fixing double loop earthing with GI plate of 20x3 mm thick electrode complete with material such as thimble, nuts and bolts, charcoal, salt 25x5 mm strip as per IS ; 3043-1987 with upto date amendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the dirction of the Engineer - in - Charge.

Collection tank to storage tank (WSS Polian Beet) : Providing horizontal spindle, horizontal / radial split casing /end suction ( back pull out arrange-ment) Single /double /multi stage of Kirloskar / KSB Crupton KSB/Calama/BS/ Groundfos/ Hindustan/ Lubbi make as per BIS IS 1520-1980 with upto date ammendments read with IS: 9137-1978 or latest edition suitable for lifting water for under mentioned characteristic with Bronze impellers / priming funnels, casing ring and shaft sleeves of Bronze shaft of stainless steel with cast iron casing, coupled directly through a flexible coupling on a common cast iron / cast steel base plate (base plate to be framed from the manufacturers of the pumping unit only) to slipring / Squirrel cage screen protected drip proof induction motor / motors of standard make such as Crompton / NGEF / GEC / Seimens /Jyoti/ Kirloskar BHEL / ABB suitable for operation on 415 (+/-15%) volts. 50 Cycles /Sec. 3 phase AC electric supply of 2900 RPM.The power of electric motor/ motors should be at least +10% in excess of the maximum power required by the pump / pumps in the Operation range of (+10%) and (-15%) of the duty point head. The motor / motors as per IS 325 IS -1978 with upto date amendments read with IS 900 -1972. It should include cost of Bearing. Nuts, Bolts and painting etc. and should meet the following requirements. (a) Pump :- Specifications i) Make ii) Model iii) No. of stages iv) Manfacurer's certificate to be attached. performance i) Discharge ii) head Make ii) Model iii) efficiency of pump a) duty Head b) (+) 10% duty head c). (-) 15% Duty Head d) performance curve to be attached b). Motors:- Specificions Make ii) Model iii) Rating iv). speed v) Insulation (C) Coupling (D) Base plate

Discharge, (Q) 9.39 LPS

Total Head ( H ) 74.31 Mts.

a) LWL In clear water Tank = 547.23 mtr

b) R.L. of shaft = 547.23 Mtrs.

c) R.L. of discharge Point. = 612.00 mtrs.

d) Suction lift. +tive mtrs.

e) Discharge Head =612.00 mtrs.

f) Static Head = 64.77 mtrs.

Rising main.

Length = 618 mtrs.

Diameter = 125mm. Dia GMS pipe

Class GMS Tube (MG)

Pumping hours. 8 hours.

Altitude of installations above M.S.L 407 mtrs.

Characteristic of Water

a)Temperature ___20_____Deg.Col.

b)Turbidity ________ JTU

c) Alloanity _________ mg/1 ca Co3

d)Size of solids __________ mm

e) Others.

(a) Pumps: Specifications:

i)Make

ii)Model.

iii)No.of stages:-

iv)Manufacturers

certificate to be attached.

Performance

i)Discharge:-

ii)Total Head:-

iii)B.H.P.

iv)Efficiency:

vi)Performance Curve to be attached.

b)Motors: Specifications.

i)Make

ii)Model

iii)Rating

iv)Speed.

v)Insulation.

(C) Coupling:

(d) Base Plate.

Providing ICTP Main Switch with HRC fuses of L&T/ Havells/ Standard / Kilburn / Siemens make and having capacity 30% extra of the operational rating as per IS : 13947-P I & II with upto date amendments.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type ) switch board i/c angle iron post of suitable height & size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising & capable of mounting the following accessories with all internal connections.

MCB of kilburn / L&T / Havells / Standard make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. i) Make : ii) Type : iii) Capacity :

ELCB of recommended make L&T Havells / Standard / Kilburn as per IS ;2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. i) Make : ii) Type : iii) Capacity :

The Voltage Monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage, reverse phasing, overloading and phase voltage difference as per IS; 3842 ( Latest Edition )

Power factor meter of standard make as per relevent IS code with upto date ammendments.

Frequency meter of standard make as per relevent IS code with upto date ammendments.

d) Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ;8084-1976 and IS :11353-1985 read with BIS ; 5578 -1985 with upto date amendments.

Three phase indicator lamps complete with toggle switches for indivual motors as per IS 3452 ( P- I&II ) with upto date amendments.

Capacitor of BHEL / GEC / L&T / Mecheil make as per IS ; 2834-1968 with upto date amendments,to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter / IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB.

Providing suitable starter of L&T /BHEL make as per IS : 13947-II with upto date 'amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic type over load release and dashpot, time lag, under voltage release, with or without initial oil filling as the case may be with single phase preventor as per IS ;1248 ( P-V ) 1983 with up to date amendments.

Providing & fixing double flanged Cast Iron Sluice valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of suction pipe of pump and capable of with standing normal Seat Pressure as per IS 14846 with upto date ammendments. 125mm dia Class PN 1.00

Providing and fixing double flanged Cast Iron Sluice valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of 100 mm dia for the delivery line of pump and capable of with standing normal Seat Pressure as per IS 14846 with upto date ammendments. Class PN 1.00

Providing double flanged swing type cast iron Reflux Valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of 125 mm dia having Bye pass arrangement on the delivery line of the of the Pump and capable of withstanding normal Seat Pressure as per IS :5312-1984 (P-I) (Cast Iron) with latest ammendments

Providing double flanged swing type cast iron Reflux Valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of 100 mm dia having Bye pass arrangement on the delivery line of the of the Pump and capable of withstanding normal Seat Pressure as per IS :5312-1984 (P-I) (Cast Iron) with latest ammendments

Providing and fixing circular dial pressure gauge of Precision / Fiebig make complete with all accessories such as stop cock,Copper tubing etc.as per IS: 3624-1987 with upto date ammendments.

Installation of all items appearing as above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and Fixing double flanged GMS/GMSERW piping work ( Layout to be approved by Engineer-in-Charge). for suction and delivery pipes suitable to pumps offered and common header as per the rising main respectively complete with all specials such as bends,Tees, Reducers / Inceasers with companion flanges matching with the relevant specifications of the accessories as indicated in the Drawing including rubber / asbestos gasket of 3 mm thickness as per IS : 2712-1972 and required number of Nuts and Bolts as per 1364-1983.-the pipes shall be as per relevent IS code and to withstand 1.50 times total head.

i) Suction Pipe 125 mm dia.

ii) Delivery Pipe 100 mm dia.

iii) Common Header 125 mm dia. and will extend upto 5 metres from the outer wall of the pump house in the direction of Rising main to be joined.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor.

Collection tank to storage tank (WSS Bat Kalan) : Providing horizontal spindle, horizontal / radial split casing /end suction ( back pull out arrange-ment) Single /double /multi stage of Kirloskar / KSB Crupton KSB/Calama/BS/ Groundfos/ Hindustan/ Lubbi make as per BIS IS 1520-1980 with upto date ammendments read with IS: 9137-1978 or latest edition suitable for lifting water for under mentioned characteristic with Bronze impellers / priming funnels, casing ring and shaft sleeves of Bronze shaft of stainless steel with cast iron casing, coupled directly through a flexible coupling on a common cast iron / cast steel base plate (base plate to be framed from the manufacturers of the pumping unit only) to slipring / Squirrel cage screen protected drip proof induction motor / motors of standard make such as Crompton / NGEF / GEC / Seimens /Jyoti/ Kirloskar BHEL / ABB suitable for operation on 415 (+/-15%) volts. 50 Cycles /Sec. 3 phase AC electric supply of 2900 RPM.The power of electric motor/ motors should be at least +10% in excess of the maximum power required by the pump / pumps in the Operation range of (+10%) and (-15%) of the duty point head. The motor / motors as per IS 325 IS -1978 with upto date amendments read with IS 900 -1972. It should include cost of Bearing. Nuts, Bolts and painting etc. and should meet the following requirements. (a) Pump :- Specifications i) Make ii) Model iii) No. of stages iv) Manfacurer's certificate to be attached. performance i) Discharge ii) head Make ii) Model iii) efficiency of pump a) duty Head b) (+) 10% duty head c). (-) 15% Duty Head d) performance curve to be attached b). Motors:- Specificions Make ii) Model iii) Rating iv). speed v) Insulation (C) Coupling (D) Base plate

Discharge, (Q) 9.90 LPS

Total Head ( H ) 100.89 Mts.

a) LWL In clear water Tank = 422.82mtr

b) R.L. of shaft = 422.82 Mtrs.

c) R.L. of discharge Point. = 506.20 mtrs.

d) Suction lift. +tive mtrs.

e) Discharge Head = 506.20 mtrs.

f) Static Head = 83.38 mtrs.

Rising main.

Length = 1110 mtrs.

Diameter = 125mm. Dia GMS pipe

Class GMS Tube (MG)

Pumping hours. 8 hours.

Altitude of installations above M.S.L 407 mtrs.

Characteristic of Water

a)Temperature ___20_____Deg.Col.

b)Turbidity ________ JTU

c) Alloanity _________ mg/1 ca Co3

d)Size of solids __________ mm

e) Others.

(a) Pumps: Specifications:

i)Make

ii)Model.

iii)No.of stages:-

iv)Manufacturers

certificate to be attached.

Performance

i)Discharge:-

ii)Total Head:-

iii)B.H.P.

iv)Efficiency:

vi)Performance Curve to be attached.

b)Motors: Specifications.

i)Make

ii)Model

iii)Rating

iv)Speed.

v)Insulation.

(C) Coupling:

(d) Base Plate.

Providing ICTP Main Switch with HRC fuses of L&T/ Havells/ Standard / Kilburn / Siemens make and having capacity 30% extra of the operational rating as per IS : 13947-P I & II with upto date amendments.

Providing MS Sheet steel fabricated floor mounted closed ( Almirah type ) switch board i/c angle iron post of suitable height & size ISA 40x40x6 mm duly painted with sheet of 16 gauge comprising & capable of mounting the following accessories with all internal connections.

MCB of kilburn / L&T / Havells / Standard make of suitable capacity on incoming feeder with or without intial oil filling as the case may be with neutral linked under voltage releases as per IS ; 2516-1985 with upto date amendments. i) Make : ii) Type : iii) Capacity :

ELCB of recommended make L&T Havells / Standard / Kilburn as per IS ;2516-1985 with up to date ammendments and of suitable range which should have control box , operating handle & trip / reset bush button on / off of indicators, reindicating off spring condition of the circuit breaker for over current protection. The circuit should be equiped with magnet thermal release with metallic tape CTS. It should also be fitted with earth fault for tripping of breaker on occurence of Earth fault. i) Make : ii) Type : iii) Capacity :

The Voltage Monitor Relay 3 phase with all protection and usual indicator and electric siren against single phasing, low voltage, high voltage, reverse phasing, overloading and phase voltage difference as per IS; 3842 ( Latest Edition )

Power factor meter of standard make as per relevent IS code with upto date ammendments.

Frequency meter of standard make as per relevent IS code with upto date ammendments.

d) Bus bar chamber having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS ;8084-1976 and IS :11353-1985 read with BIS ; 5578 -1985 with upto date amendments.

Three phase indicator lamps complete with toggle switches for indivual motors as per IS 3452 ( P- I&II ) with upto date amendments.

Capacitor of BHEL / GEC / L&T / Mecheil make as per IS ; 2834-1968 with upto date amendments,to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVA rating according to H.P. offered including cables as per relevent ISI code ( of Seimens / Glocter / IEC make ) from bus bar chamber to capacitor as per IS : 4064-1978 with upto date amendments . Rating of capacitor will be approved by HPSEB. i) Make : ii) Type : iii) Capacity :

Providing suitable starter of L&T /BHEL make as per IS : 13947-II with upto date 'amendments for Squirrel cage / Slipring motor mounted on panel board with magnetic type over load release and dashpot, time lag, under voltage release, with or without initial oil filling as the case may be with single phase preventor as per IS ;1248 ( P-V ) 1983 with up to date amendments.

Providing & fixing double flanged Cast Iron Sluice valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of suction pipe of pump and capable of with standing normal Seat Pressure as per IS 14846 with upto date ammendments. 125mm dia Class PN 1.00

Providing and fixing double flanged Cast Iron Sluice valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of 100 mm dia for the delivery line of pump and capable of with standing normal Seat Pressure as per IS 14846 with upto date ammendments. Class PN 1.00

Providing double flanged swing type cast iron Reflux Valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of 125 mm dia having Bye pass arrangement on the delivery line of the of the Pump and capable of withstanding normal Seat Pressure as per IS :5312-1984 (P-I) (Cast Iron) with latest ammendments

Providing double flanged swing type cast iron Reflux Valve of Leader / Krloskar / Suchdeva / LP / Kartar / and any other approved make of 100 mm dia having Bye pass arrangement on the delivery line of the of the Pump and capable of withstanding normal Seat Pressure as per IS :5312-1984 (P-I) (Cast Iron) with latest ammendments

Providing and fixing circular dial pressure gauge of Precision / Fiebig make complete with all accessories such as stop cock,Copper tubing etc.as per IS: 3624-1987 with upto date ammendments.

Installation of all items appearing as above as per the systematic drawing attached with the documents or as per the direction of Engineer - in- charge.

Providing and Fixing double flanged GMS/GMSERW piping work ( Layout to be approved by Engineer-in-Charge). for suction and delivery pipes suitable to pumps offered and common header as per the rising main respectively complete with all specials such as bends,Tees, Reducers / Inceasers with companion flanges matching with the relevant specifications of the accessories as indicated in the Drawing including rubber / asbestos gasket of 3 mm thickness as per IS : 2712-1972 and required number of Nuts and Bolts as per 1364-1983.-the pipes shall be as per relevent IS code and to withstand 1.50 times total head.

i) Suction Pipe 125 mm dia.

ii) Delivery Pipe 100 mm dia.

iii) Common Header 125 mm dia. and will extend upto 5 metres from the outer wall of the pump house in the direction of Rising main to be joined.

Providing and laying copper PVC insulated armoured power cable (one cable carrying all the three phases) of suitablle size and capacity to motors and all other electrical equipments as per IS ;1554 ( P-I ) 1988 or latest with upto date amendments of Seimen /Gloster / IEC / ICC / EICO / National / Grandlay Finolex/ Havells make including all other accessories such as thimble, flexible pipes, solder nuts and bolts,cable glands etc. laid in pipes of trenches under floor.

Providing and fixing double loop earthing with GI plate of 20x3 mm thick electrode complete with material such as thimble, nuts and bolts, charcoal, salt 25x5 mm strip as per IS ; 3043-1987 with upto date amendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the dirction of the Engineer - in - Charge.

Civil work : C/O Pump Houses, Boundary walls and C./O under ground reservoirs/ collection tanks

Excavation in foundation, trenches in earth work in all kinds of soil,such as pick work,jumper work.blasting work in hard rock and soft rock and in saturated soil etc. i/c all leads and lifts , stacking the excavated soil not more than 3 mtrs. clear form the edge of excavation and then returning the stacked soil in 15 cm layers when required into plinth, sides of foundation etc. consolidating each deposited layers by ramming and watering and then disposing of all surplus excavated earth as per the direction of the Engineer-in-Charge.

Providing and laying cement concrete 1: 6: 12 ( 1 cement : 6 sand :12 graded stone aggregate 40 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts and as per the direction of the .Engineer-in-Chaarge.

Providing and laying cement concrete 1: 5: 10 ( 1 cement : 5 sand :10 graded stone aggregate 40 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts and as per the direction of the .Engineer-in-Charge.

Providing and laying cement concrete 1: 3: 6 ( 1 cement : 3 sand :6 graded stone aggregate 40 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts and as per the direction of the .Engineer-in-Charge.

Ist class brick work using common burnt clay building bricks in foundation and plinth in cement mortor 1:6 (1 cement: 6 sand ) in all leads and lifts as per the direction of the Engineer-in-Charge.

Ist class brick work using common burnt clay building bricks in superstructure in cement mortor 1:6 (1cement :6 sand) in all lead and lifts as per the direction of the Engineer-in-Charge.

Ist class brick work using common burnt clay building bricks in foundation and plinth in cement mortor 1:4 (1 cement :4 sand) in all lead and lifts as per the direction of the Engineer-in-Charge.

Providing and fixing pressed steel door frame manufactured from commercial MS sheets of 1.25 mm thickness including hinges jump lock jamb, bead if required angle thrshold of MS angle of section 50x25 mm or base ties of 1.25 mm presses MS welded or rigidly fixed together by mechanical means, adjustable lugs with split and tails to each jamb including steel butt hinges 2.5 mm thick with guards, lack strike plate and shock absorberas specified and applying a coat of approved steel primer after pretreatment of the surface as directed by Engineer-in-Charge.

Profile "A"

Providing and fixing pannelled glazed and panalled and glazed shuttrs for doors ,windows and clerestory windows including bright finshied /black enemelled iron butt hinges with necessary screws 40 mm thick. 2 nd class deodar wood complete in all respect and as per the direction of the Engineer - in- Charge.

Providing and fixing wire gauge shutters using galvanized MS wire gauge of I.S.gauge designation 85G(eighty five ) with wire of dia 0.56 mm(zero point five six millimetre) for doors windows and clerestory windows including bright finished black enameled iron butt hinges with necessary screws 40mm(forty millimetre )thickof second class deodar wood with in all leads and lifts and as per the direction of the Engineer - in- Charge.

Providing and laying cement concrete 1:1.5:3 ( 1cement : 1.5 sand : 3 graded stone aggregate 20 mm nominal size ) and curing complete excluding the cost of form work and reingorcement for reinforced concrete work in :-

Foundation, footing and bases of columns and the like and mass concrete within all leads and lifts complete in all respect.

Suspended floors, roofs, landing and shelves and their support balconies, beams, girders, bressumers and cantilevers upto floor two level.

wall (in any thicness but not ess than 0.10 mt thicknes) attached pillaster, Buttresses, plinth and string courses etc. From top of foundation level upto floor two level)

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centering, shuttering, struting and propping etc. with wooden battens and ballies, height of propping and centering below supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for in situ-reinforced concrete and plain Concrete work in :-

Foundation, footing and bases of columns and the like and mass concrete within all leads and lifts complete in all respect.

Flat surfaces such as soffits of suspended floors, roofs, landing and the like Floors etc. upto 200 mm thickness in all leads and lifts and as per the direction of the Engineer-in-Charge.

Beams,cantilever,girders and lintels.Sides and soffits of beams,beam haunchings, cantilevrs, bressumers and lintles not exceeding 1.00 mtr.in depth in all heights from floor.

Vertical surfaces such as walls (any thickness) partitions and the like i/c attached pillastres buttresses, plinth & string courses and the like.

Cement concrete flooring 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size ) laid in one layer finished with a floating coat of neat cement in all leads and lifts and as per the direction of the Engineer-in-Charge 40 mm thick.

6 mm cement plaster in ceiling with cement mortor 1:3 ( 1 cement :3 sand ) in all leads and lifts as per the direction of the Enginner-in-Charge.

15 mm cement plaster in single coat on rough side of brick masonry for interior plastering upto floor two level including arrises, internal rounded angle, chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth with cement mortor 1:6 ( 1 cement :6 sand ) in all leads and lifts as per the direction of the Enginner-in-Charge.

20 mm cement plaster in single coat on rough side of brick masonry for interior plastering upto floor two level including arrises, internal rounded angle, chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth with cement mortor 1:6 ( 1 cement :6 sand ) in all leads and lifts as per the direction of the Enginner-in-Charge.

Pointing on brick work with cement mortor 1:3 ( 1 cement: : 3 sand ) in all leads and lifts as as per the direction of the Engineer - in- Charge.Cut or weather struck.

Providing and laying brick tiles over mumty /terrace roofs grouted with cement mortar 1:3 ( 1 cement : 3 sand) over a 12mm(twelve millimeter) layer of cement mortar 1:3( 1 cement : 3 sand ) and finished neat including carriage of material with in all leads and lifts and other incidentals.

Providing plinth protection 50 mm thick in cement concrete 1:3:6 ( 1 cement :3 sand : 6 graded stone aggregate 20 mm nominal size ) in all lead and lifts as per the direction of the Engineer - in- Charge.

Constructing brick masonary 'U' shape open surface drain with side wall. 15 x 22 cm in cement mortar 1:6 ( 1 cement : 6 sand) and inside plastering with cement plaster 1:3 ( 1 cement : 3 sand) including earth work and laying 10 cm cement concretein 1:5:10 ( 1 cement : 5 sand :10 graded stone aggregate of 40 mm nominal size) and 7.5 cm.cement concrete 1: 2:4 ( 1cement : 2 sand : 4 graded stone aggregate 20 mm nominal size ) and finished with a floating coat of neat cement complete as per standard design.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by throughly cleaning oil, grease,dirt,and other foreign matter sand papering and knotting with ready mixed paint brushing wood primer pink complete in all respect as per the direction of the Engineer-in-Charge.

Painting two coats excluding priming coat on new wood and wood surfaces with enamel paint to give an even shade including cleaning the surface of dirt ,dust and other foreign matter sand papering and stoping complete in all respect as per the direction of the Engineer - in - Charge.

White washing with lime on undecorated wall surface ( three coats) to give an even shade including throughly brooming the surface to remove all dirt ,dust mortor drops and loose scale of lime wash and other foreign matter complete in in all respect as per the direction of the Engineer-in-Charge.

Distempering with dry distemper of approved brand and manufacture ( Two coats) and of required shade on undecorated wall surfaces to give an even shade over & including a primer coat of whiting after thoroughly brushing the surface free from mortar droppings and other foreign matter including preparing the surface even & sand papering / smooth including carriage of material in all leads and lifts.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surface (two coats) to give an even shade after thoroughly brushing the surface to remove all dirt & remains of loose powdered materials complete in all respect

Providing and fixing MS grills of required pattern in wooden frame / pressed steel frame with MS flats square / rounds bars 12 mm dia with round headed bolts and nuts or by screws in all leads and lifts and as per the direction of the Engineer - in- Charge Plain grills.

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level in all respect in all leads and lifts & as per direction of the Engineer-in-Charge.

Providing 40x3mm flat iron hold fast 40 cms long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15 cms 1:3:6 ( 1 cement :3 sand : 6 graded stone aggregate 20 mm nominal size ) complete in all respect as per the direction of the Engineer -in- Charge.

Providing and fixing sliding door bolts anodized transparent or dyed to required shade and colour with screws etc. complete in all respect 250x16 mm

Providing and fixing tower bolts barrel type anodized transport or dyed to required shade and colour with screws com lete in all respect. 250x10mm.

Providing and fixing aluminium handle anodized transparent or dyed to required shade and colour with screws etc. complete in all respect 100mm dia

P/F MS fan clamps type 1 of 16 mm dia bar bent to shape with hooked ends in RCC slab during laying including painting the exposed portion of roof as per standard design complete in respect .

Half brick work using common burnt clay building bricks in super structure above 1st. floor level in cement mortar 1 : 4 ( 1 cement :4 sand) of 1st. Class bricks complete in all lead and lifts as per the direction of the Engineer-in-Charge.

Steel work welded built up sections, trusses and framed work , including cutting , hoisting , fixing in position and applying a priming coat of red lead paint in beams joists channels, angles , tees, flats with connection plates or gratings framed guard bars, ladders,. railling, brackets and similar works.

Providing form work of ordinary timber plankings, so as to give a rough finish including centring, shuttering , strutting and propping etc height of propping and centering below supporting floor to ceiling not exceeding 6.00 mtrs.height and removal of the same for in situ reinforced concrete and plane concrete work in arches upto 6 mtrs span complete in all respect in all leads and lifts.

Providing in RCC work smooth finishing of the exposed surface with cement mortor 1:3 (1cement :3 Sand) complete in all respect within all leads & lifts.

Providing & laying cement concrete using M- 25 graded stone aggregate 20 mm nominal size) & curing complete excluding the cost of form work & reinforcement for reinforced concrete work in

Suspended floors, roofs, landing and shelves and their support balconies, beams, girders, bressumers and cantilevers upto floor two level complete in all respect in all lead

Arches up to all floors complete in all respect in all lead

Providing and fixing of GMS Pipes (M)conforming to relevants BIS codes of below mentioned diameters fully jointed with MS Flanges of Table - 5 as per IS :6392 - 1971 excluding the cost of excavation in trenches complete in all respect within all leads & lifts.

100 mm Inlet pipe, Outlet pipe, Over flow pipe & Scour pipe

Providing & fixing CI sluice valve (with hand wheel) as per IS:780 - 1984 Class-I upto 300 mm dia i/c brass spindle & as per 2906 - 1984 Class II i/c MS Flange i/c carriage of material within all leads and lifts bolts,nuts,rubber insertion etc,(The tail pieces if required shade etc.

100 mm dia class PN-1.00

Constructing chamber for sluice valve, with CI surface box 100 mm top dia.,160 mm bottom dia.&180 mm deep (inside) with chained lid RCC top 1: 2: 4 mix (1 cement :2 Sand :4 graded stone aggregate 20 mm nominal size ) 100 mm thick foundation conc.1:5:10 mix (1cement : 5 sand : 10 graded stone aggregate 40 mm nominal size) & inside plastering with cement mortor 1:3 (1 Cement : 3 Sand ) finished with a floating coat of neat cement i/c curing complete. 600 x 600 x 750 mm inside size With 150mm thick walls of RCC 1:2:4 (1cement : 2 sand :4 graded stone aggregate 20 mm nominal size) complete with form work & reinforcement with 6 mm bars at not exceeding 150 mm centres both ways within all leads and lifts complete in all respect.

Providing & fixing 560 mm dia.SFRC man hole cover with frame and the weight of frame & cover should not be less than 100 kg complete in all respect within all leads & lifts.

Wiring for light/Fan point/Exhaust fan point/call bell point with 1.5 Sq.mm PVC insulated copper conductor cable in surface/recessed PVC conduct at required including carriage of all material within all leads and lifts. Group "C"

Wiring for light/power plug with 2 x 4 Sq.mm PVC insulated copper conductor or single core cable in surface/recessed steel conduit alongwith 1 No. 4 Sqmm dia bare copper wire for loop earthing as required including carriage of materials within all leads and lifts.

Wiring for circuit wiring with 2 x 1.5 Sq.mm PVC insulated copper conductor single core cable in surface/recessed steel conduit as required including carriage of material within all leads and lifts.

Wiring for sub-main wiring with the following size of copper conductor single core cable in surface/recessed steel conduit as required including carriage of materials upto all leads and lifts. 2x6 Sq.mm

Supplying and fixing metal box of 180 x 100 x 60mm deep (Nominal size) on surface/recess with suitable size phenolic leminated sheet cover fixing 3 pin 5/6 amps socket tumber/piano type switch connections painting etc. including carriage of materials within all leads and lifts.

Supplying and fixing backellite batten/angle holder including connection as required.

Providing, installing, testing and commissioning of ceiling fan and regulator including wiring the rod of standard length (upto 30cm) with 1.5 Sqmm PVC insulated copper conductor single core cabe etc. as required sweep type. Cat. A (1200 mm sweep)

Providing, installation, testing and commissioning of prewired flourscent tube fitting complete with ballast, starter and capactors but excluding flourscent tube rod, suitable to operate on 230 volts single phase A.C.supply directly on surface with copper wiring as required including carriage of materials within all leads and lifts tube fixture 1 x 36 watt Box type Category "A".

Supplying and fixing 40Amps to 63 Amps rating 240 Volts "L" series miniature circuit breaker of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required including carriage of material within all leads and lifts. Category- A, 63 Amps.

Supplying and fixing of following way single pole and neutral sheet steel MCB distribution board 240 volts on surface/recessed completed with tinned, copper busher neutral link, earth bar, detachable gland plate inter -connections, including painting, earthing etc. as required Bus bar 8 way.

Supplying and fixing 5Amps to 32 Amps rating, 10 KA breaking capacity 240 volts, C series miniature circuit breaker of following poles in the existing MCB, DB complete with connections testing and commissioning etc. Category "A", single pole.

Earthing with G.I. pipe earth, pipe 4.5 mtrs length, 40mm dia including accessories and providing masonry enclousres with cover plate having locking arrangement and watering pipe etc.( but without charcal coke and salt) complete as required including carriage of materials within all leads and lifts.

Extra using salt and charcoal for pipe earth electrode as required, including carriage of materials within all leads and lifts.

Supplying and laying 6 Sqmm G.I.wire at 0.50 mtr below ground level for conductor earth electrode, including soldering etc. as required including carriage of materials within all leads and lifts.

Providing, fixing & testing Street Light Fixture with CFL of 36 watt, copper ballast, G.I. Pipe bracket, complete in all respects including carriage of materials within all leads and lifts..

C/O RCC OHSR 120000 lrs cap. at Laluwal, 50000 ltrs cap at Laluwal & at Polian Janani, 80000 trs capacity at Polian, 35000 ltrs capacity at Polian, 20000 ltrs cap. at polian and 165000 ltrs cap. at Bat Khurd with 15mtr staging height each)

Excavation in foundations,trenches etc., in earth work, lift upto 1.50 mts. Stacking the excavated soil not more than 3 mts. Clear from the edge of the excavation & then returning the stacked soil in 15 cms. Layers,when required into plinths sides of foundation etc.,consolidating each deposited layers by ramming & watering & then disposing of all surplus excavated earth as dierected within all leads & lifts as per entire satisfaction of Engineer in charge.

Providing & laying cement concrete M-10 mix concrete using graded stone aggregate 40 mm nominal size, excluding the cost of centring & shuttering in Foundation & plinth as dierected within all leads & lifts as per entire satisfaction of Engineer in charge.

Providing & laying cement concreteM- 30 (not leaner than 1:1.5:3) mix concrete using aggregate 20 mm nominal size) & curing complete excluding the cost of form work & reinforcement for reinforced concrete work in all leads and lift and as per the direction of Engineer-in-Charge.

Foundation,footing.bases of columns & the like & the mass concrete.

(ii) Wall (any thickness but not less than 0.10 mts.Thickness)attached pillasters,buttresses plinth,& string courses etc.from top of found.level upto floor two level

(i) floor four level to floor five level

Column,pillars,posts & struts upto floor two level

(ii) floor two level to floor three level

(iii) floor three level to floor four level

(iv) floor four level to floor five level

Lintels,beams girders bressumers & cantilevers upto floor two level

(ii) floor two level to floor three level

(iii) floor three level to floor four level

Arches:

floor two level to floor three level

floor three level to floor four level

Suspended floors,roofs,landings and shelves & their support balconies,beams ,girder,bressumers and cantilever. upto floor two level as dierected within all leads & lifts as per entire satisfaction of Engineer in charge.

Prov.form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5mm,so as to give a fair finish i/c centring shuttering,strutting & propping etc. with wooden battens & ballies,ht. of propping & centring below supporting floor to ceiling not exceeding 4.00 mts. & removal of the same for in situ-reinforced concrete & plain concrete work :-

(i) Foundation,footing,bases of columns etc.and mass concrete.

(ii) Flat surface such as soffits of suspended floors,roofs,landing and the like

(iii) Vertical surfaces such as walls (any thickness) partitions and the like i/c attached pillastres buttresses, plinth & string courses and the like.

(a) Upto 4.00 mtrs.

For Vertical surfaces of tank

Columns,pillars,posts & struts,square ,rectangular or polygonal in plan.

(b) Beyond 4.00 mtrs.

Beams,cantilivers, girders and lintels : Sides & soffits of beams,beam haunchings, cantilevers, bressumers & lintels not exceeding 1.00 mtr.depth in all ht.from floor.

Providing form work of ordinary timber plankings, so as to give a rough finish including centring, shuttering, strutting and propping etc height of propping and centering below supporting floor to ceiling not exceeding 6.00 mtrs.height and removal of the same for in situ reinforced concrete and plane concrete work in arches upto 6 mtrs span in all respect in all leads and lifts.

Beyond 4.00 mtr.height.

Providing Tor steel reinforcement for RCC work including bending,binding & placing in position complete upto floor two level.

Providing in RCC work smooth finishing of the exposed surface with cement mortor 1:3 (1cement :3 Sand) complete in all respect within all leads & lifts.

Finishing wall with water proofing cement paint of approved brand & maunfacture and of required shade on undecorated wall surfaces (two coats) to give an even shade after throughly brushing the surface to remove all dirt & remains of loose powedered material etc complete in all respect.

Providing & fixing 500 mm dia.SFRC man hole cover with frame and the weight of frame & cover should not be less than 100 kg complete in all respect within all leads & lifts.

Providing and fixing of GMS Pipes (M) conforming to relevants BIS codes of below mentioned diameters fully jointed with MS Flanges of Table - 5 as per IS :6392 - 1971 excluding the cost of excavation in trenches complete in all respect within all leads & lifts.

100 mm Inlet pipe, Outlet pipe, Over flow pipe & Scour pipe

80 mm Inlet pipe, Outlet pipe, Over flow pipe & Scour pipe

Steel work welded in built up sections,trusses & framed work i/c cutting, hoisting,fixing in position & applying a priming coat of red lead paint.In grating,framed guard bars,ladders,railing,brackets & similar works.

Providing and fixing of GMS Pipes conforming to IS 1239 - 1979 (Part-1) screwed & socketed joints (Light grade) excluding the cost of excavation in trenches 25 mm Dia

Providing & fixing CI sluice valve (with hand wheel) as per IS:780 - 1984 Class-I upto 300 mm dia i/c brass spindle & as per 2906 - 1984 Class II i/c MS Flange i/c carriage of material within all leads and lifts bolts,nuts,rubber insertion etc,(The tail pieces if required shade etc.

100 mm Inlet pipe, Outlet pipe, Over flow pipe & Scour pipe

80 mm Inlet pipe, Outlet pipe, Over flow pipe & Scour pipe

Providing & fixing bends of required degrees made from parent tubes conforming to relevant codes fully flanged with MS Flange of Table - 5 conforming to IS: 6392 - 1971 complete in all respect within all leads & lifts.

100 mm Inlet pipe, Outlet pipe, Over flow pipe & Scour pipe

80 mm Inlet pipe, Outlet pipe, Over flow pipe & Scour pipe

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1 Cement: 3 Sand: 6graded stone aggregate 20 mm nominal size) complete in all respect within all leads & lifts.

Providing under layers for plinth protection 75 mm thick (unconslidated) bed dry brick/stone aggregate 40 mm nominal size with rammed & grouted with fine sand i/c preparation of ground complete in all respect within all leads & lifts.

Constructing chamber for sluice valve, with CI surface box 100 mm top dia.,160 mm bottom dia.&180 mm deep (inside) with chained lid RCC top 1: 2: 4 mix (1 cement :2 Sand :4 graded stone aggregate 20 mm nominal size ) 100 mm thick foundation conc.1:5:10 mix (1cement : 5 sand : 10 graded stone aggregate 40 mm nominal size) & inside plastering with cement mortor 1:3 (1 Cement : 3 Sand ) finished with a floating coat of neat cement i/c curing complete. 600 x 600 x 750 mm inside size With 150mm thick walls of RCC 1:2:4 (1cement : 2 sand :4 graded stone aggregate 20 mm nominal size) complete with form work & reinforcement with 6 mm bars at not exceeding 150 mm centres both ways within all leads and lifts complete in all respect.

Providing and Fixing of Lightening conductor i/c carriage all leads and lifts.

Providing and Fixing Water measurement gauge of standard design complete in all respect.

Providing and Fixing vent opening i/c cowl with mesh in the top of the tank i/c carriage. As per the dirction of the Engineer-in -charge.

Structural designs and drawings complete in all respect.

Soil testing report for bearing capacity of soil.

puneet angra

Ashwani Kumar Govt Contractor

Gagandeep Singh Govt Contractor