Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | l1₹34.8 LAccepted-AOC | l1 | Accepted-AOC Tender AoC |
Tender Value
₹37.7 L
EMD Value
₹75,500
Closing Date
3 Aug 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE West Hisar
GE West Hisar Hisar Mil Stn-125006
CA NO GE(W)/HSR-55/2021-22 ADDN/ALTRATION TO OTM ACCN AT DIV TRG AREA AT BHOJRAJ AT HISAR MIL STN UNDER GE (WEST) HISAR
2022_MES_511169_3
GE(W)/HSR-55/2021-22
Open Tender
Civil Works
Item Rate
180 days
GE West Hisar Mil Stn
As per NIT
8 documents required · 8 mandatory
₹500
GE West Hisar
₹75,500
Yes
2 Sept 2022
30 Jun 2022
5 Aug 2022
30 Jun 2022
3 Aug 2022
20 Jul 2022
Amount
Dismantling asbestos cement corrugated or semi corrugated sheets as in roof covering complete all as specified and directed.
Taking down chowkats or frame with shutter, without taking off shutter from the frames area exc 1.5 sqm but not exc 4sqm each complete all as specified and directed.
Dismantling floor hearth or wall tiling incl cement mortar bedding complete all as specified.
Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed.
Excavating in trenches, n.exc 1.5 m wide and n.exc 1.5 m in depth; for foundation etc n.exc 10 sqm on plan and getting out in soft/loose soil complete all as specified and directed.
All as above Ser No 5.00 but exc 1.5 m & n.exc 3.0 m in depth complete all as specified and directed.
M&L Hard core of gauge n exc 63mm, deposited, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface with broken stone or boulders complete all as specified and directed.
M&L for PCC 1:4:8 type D2 (40 mm graded aggregate ) in foundations, filling and mass concrete complete complete all as specified and directed.
M&L for RCC M-25 Design mix as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete
M&L for RCC M-25 design Mix as in Columns, pillars, piers,posts and struts complete all as specified and directed.
M&L RCC M-25 Design Mix as in Beams,cantilevers, bressummers,lintels over1.5m span complete all as specified and directed.
M&L for brick work with fly ash Bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 all as specified and directed
M&L for cement concrete type C-2, 1:3:6 (40 mm graded aggregate) 75 mm thick as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.
Forming construction joint 50mm deep x 10mm wide and filled with sealing compound grade 'A' complete all as specified and directed.
M&L for steel work in tubular/ square hollow/ rectangular hollow trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.
M&L MS plates plain Squire cut forming holes without any attachment conforming to Fe 410-0 complete all as specified and directed.
S&F mild steel flat iron 30x5mm as in wind tie complete all as specified and directed..
S&F mild steel bolts purpose made hexagonal or squire head one and exc 15cm long and not exc 22.50 cm long and dia meter of shake 16 to 20 mm complete all as specified and directed.
M&L for preparation of new steel surfaces of any description n.exc 10cm in width of girth and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed.
M&L for painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified.
S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified
Removing excavated material n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.
Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 cm in hard/dense soil complete all as specified and directed.
M&L for reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.
Ditto, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.
Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to batter complete all as specified and directed.
M&L Formwork to sides of pillars,posts, struts, piers, columns and stanchions. complete all as specified and directed.
M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders , bressummers,lintels, cantilevers, shelves including supports, overhangs , etc. also splays between floors and beams, etc.complete all as specified and directed.
M&L Rendering 10 mm thick on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement on walls in CM 1:6 complete all as specified and directed.
M&L Rendering 15 mm thick on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement on external walls in CM 1:4 complete all as specified and directed.
M&L two coat of oil emulsion distemper on walls incl preperation of newly untreated surface and Chalk whiting, on plastered surfaces, preparatory to distempering complete all as specified and directed.
M&L two coat of cement base paint on walls incl preperation of newly untreated surface with a coat of cement wash with portland cement complete all as specified and directed.
S&F pressed steel frames 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified.
Supply & fixing box type steel windows with side hung shutters including projection type hinges with steel handle, tower bolt and steel peg stay, complete with glazing bars dovetailed or welded all as specified.
Supply & fixing box type steel windows with side hung shutters including projection type hinges with steel handle, tower bolt and steel peg stay, complete without glazing bars dovetailed or welded all as specified.
S&F, 3 mm sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 sqm in each plane complete all as specified and directed.
S&F Galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.
S&F 35mm thick glazed and skelton shutters open rebated and prepared to receive gauze etc (without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred breds for securing glass etc sizes of members of shutters as specified in SSR Pt-I Sec 8 Clause 8.20(a) in 2nd class hard wood complete as directed
S&F 35mm thick factory made plain framed, paneled shutter made of 2nd class HW (Bonsum/Hollock) of 35 mm thick(two panels)with lock rail and panel of 12 mm veneered particle board with commercial veneering on both faces. The size of rail and styles as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete as directed.
S&F 150 mm extruded Aluminium handles, cast type,anodised complete all as specified and directed.
S&F Aluminium anodised barrel tower bolt of extruded section 200mm long all as specified and directed.
M&L preparation of new wooden surface of any description and applying two coats of synthetic enamel paint over one coat of pink primer, over 10cm width or girth complete
S & F aluminium alloy anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheets cast or extruded section and fixing bolts of extruded section or cast aluminium alloy 250mm size all as specified and directed complete
S&F butt hinges 100mm, medium weight complete all as specified and directed.
S&F 300mm long mild steel ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed.
M&L non skid ceramic tiles 7 to 8 mm thick light shade (Square / rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors over and including provision of cement screed bedding layer 15 mm thick in CM 1:6 etc set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed.
All as per item No 46.00 above but in skirting with backing coat of 10mm thick CM 1:4 complete all as specified and directed.
S&F Gl frame work of 605X605mm size for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion asteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed.
S&F hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified
Providing and fixing 08 mm thick calcium silicate board of siliceous & calcareous material reinforced with cellulose fiber for fixing in 600mm X 600mm grid, (Frame work for ceiling shall be measured and paid separately complete all as specified and directed.
Pointing wiring complete with 1.5 sq mm, single core ,PVC insulated but unsheathed, FRLS cable, 1100 volts grade laid/drawn through & including rigid PVC conduit with necessary conduit fittings/accerssories fixed concealed in walls/ceiling by means of PVC sleeve/dash fastener with cadmium plated iron screws all as per ISI including sunk type pressed steel terminal boxes for mounting fittings like switches sockets fan regulator etc with 3mm thickplastic laminated sheet top covers oncealed in walls etc including 1.5 Sq mm single core PVC insulated but unsheathed multistranded copper conductor FRLS cable as continuousm earth wire to common eath and connecting to earth dolly of following (a) One light point /fan/Exhaust Fan controlled by one switch
All as per above item No 51.00 but one socket out let 5 pins 5 Amps on the independent board
All as per above item No 51.00 but one socket out let 5 pins 5 Amps on the same board with other switches complete all as specified and directed
All as per item No 51.00 but 2.5 Sqmm PVC insulated and unsheatherd FRLS single core multistranded copper conductor incl 2.5 Sqmm PVC insulated and unsheathed FRLS copper earth wire for switch socket combination 3 pin 15 amps on inependent board
Supply & fixing Socket out let flush type 3/6 pin, suitable for 15 Amps plug top multipurpose 230 V complete all as specified and directed
Supply and fixing socket out let flush type 5 pin suitable for 5 amp 230 V all as specified and directed
Supply only piano type switch 5 Amps, S.P. one way flush type complete all as specified and directed.
Supply only piano type switch 15 Amps, S.P. one way flush typecomplete all as specified and directed.
Supply only lamp holder insulated body with back plate suitable for batten fittings complete all as specified and directed. .
Supply and fixing LED bulb of capacity 9 W all as specified and directed
Supply only ceiling rose surface bakelite three terminals size 65 x 50 mm complete all as specified and directed.
Supply and Fixing in replacement LED tube rod only having aluminium extrusion 18/20W, 4ft for existing tubelight fitting all as specified and directed
Supply and fixing in replacement LED Batten CRCA sheet box type fixture 4 feet,long Single Side Connection suitable for 18/20w Led tube light with LED Rod Complete with Mounting Brackets & accessories as required with connections.
S&F electronic ceiling fan regulator stepped type heavy duty suitable to work on 230 volts complete all as specified.
S&F ceiling fan single phase 230 V 1200mm sweep energy efficient rating complete with all connecting accessories etc
Supply and fixing MCB single pole, 240 volts 6 Amps to 32 Amp breaking capacity 10 KA (type B )
Supply and fixing MCB SPN 240 volts 40 Amps breaking capacity 10 KA (type B )
S&F sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with isolated Neutral Bar & Shrounded bus Bar IP protection 43 heavy door earthing
Supply & fixing in replacement LED street light luminaries of cap 25 watt, SPD -10KV internal with lense, 240 volt, ,pressure dia cast aluminium housing frame, heat resistant toughtened clear glass with frame complete with accessories , IP 66 protection, pre wired up to a terminal block and mounting attachment, of GI pipe 40mm dia light grade bend to required shape for fixing of light of length 1.2 Mtr including MS climps nuts bolts, & whaser duly required with PCC in wall complete all as specified and directed
M&L for Earthing complete with galvanised mild steel earth electrode plate 600 X 600 X 6 mm thick buried directly and vertically in ground connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical Plate No 3 of MES SSR Part-I and including necessary excavation and earth work in any type of soil removal and refilling of soil and funnel with wire mesh and GI watering pipe 20mm dia Chamber in PCC 1:3:6 type C1 uding 20mm graded stone aggrefate and 40mm thick cover in RCC 1:2:4 type B1 using 20 mm graded stone aggregate and reinforced with 8mm dia TMT bars at 150mm c/c on both ways handle with 16mm dia round bars and 15mm dia GI pipe up to 7.5m for protection and connected to earthing test point all as specified and indicated testing on completion :- Note : (i) GI earth lead wire upto 7.5m shall be measured and paid under this items. (ii) PCC chamber shall be provided 50cm away from the plinth of buildling.
S&F metalic exhaust fan AC single phase 230/240V of size 380mm sweep with louver complete all as specified and directed
Excavation in trenches in soft/loose soil not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of cable etc. and for foundation of poles, stays etc. n exc 10 sqm on plan and n exc 1.5 in depth and getting out complete all as specified.
Returning filling with earth obtained from excavation including spreading, watering & consolidation in layers not exceeding 15 cms thick, complete all as specified and directed.
Removing surplus soil to a distance not exceeding 50 m & depositing at a level not exceeding 1.5 m above the starting point complete all as specified and directed.
Material & labour for Sand filling in trenches with clean dry fine sand unwashed including gently punning around cables complete all as specified and directed.
Material & labour for bricks covering to under ground electric cable using sub class 'B' bricks laid dry, flat, perpendicular to the direction of the cable complete all as specified and directed.
Material & labour for replacement of 40 mm bore GI pipe light grade laid in trenches or fixed to wall/pole for protection of cable/earthing strip etc complete all as specified and directed.
Supplying laying, jointing, testing and commissioning of LT XLPE insulated screened PVC beded galvanised steel strip or wire armoured electric cable (heavy duty) with aluminium conductor 1100 volts grade, cross sectional area 70 Sqmm 3.5 core with suitable size cable glands , cable lugs complete all as specified and directed by Engr -in-Charge. (Note :- cable may be laid in trenches, under road, across the nallah, along poles/walls and in ducts etc . Excavation, earhtwork, sand cushioing, cable cover, pipe for cable protection to be measured and paid separtely) .
Supplying laying, jointing, testing and commissioning of LT XLPE insulated screened PVC beded galvanised steel strip or wire armoured electric cable (heavy duty) with aluminium conductor 1100 volts grade, cross sectional area 16 Sqmm 2 core with suitable size cable glands , cable lugs complete all as specified and directed by Engr -in-Charge. (Note :- cable may be laid in trenches, under road, across the nallah, along poles/walls and in ducts etc . Excavation, earhtwork, sand cushioing, cable cover, pipe for cable protection to be measured and paid separtely) .
Supply, installation, commissioning and testing of feeder pillar box cubical type, factory made, CPRI approved ,LT(415 Volts, 50 Hz , 3-phase, 4 wire supply) duly mounted on iron leg of size 50x50x6mm,outdoor type,double door,weather and vermin proof (Protection Class IP-54),with ventilation louvers and 3.15 mm thick MS CRCA sheet and angle iron frame work with both side hinged opening for external, rubber lining, locking arrangement, Powder Coated externally and internally over a coat of red oxide primer including foundation of panel in PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) of required/ suitable size complete including grouting of frame with PCC mortor for installation of panel of following : - (a) Bus Bar chamber comprising 4 Nos copper strip bus bars air insulated and PVC sheathed, capacity not lesss than 1.5 times of incomig MCCB with colour coding in separate sheet steel enclosure. (b) Panel mounted Digital Voltmeter , three phase, 96mm X 96 mm square flush mounted-1 No (c) Panel mounted Digital Ammeter , three phase,, 96mm X 96 mm square flush mounted with suitable ratio of CTs-1 No (d) LED type/Neon type Indicating lamps panel mounting type RYB-3 Nos (e) MCCB 415 Volts, 100 Amp, rating 4 Pole,thermal adjustable type, Service Breaking Capacity 16 kA-1 No(incoming) (g) MCCB 415 Volts, 63 Amp, rating 4 Pole,thermal adjustable type, Service Breaking Capacity 16 kA-1 No(Out going) (g) MCB SPN,240 Volts, 40 Amps,Breaking Capacity 10 kA-3 No(Out going) (h) Internal wiring with multistranded copper conductor cable/ PVC Insulated aluminium Strip of suitable size incoming to bus bar and bus bar to outgoing MCCB/MCB-1Job. (i) Fine wiring with single core copper conductor cable for instruments/indicating lamps-1 Job. Note :- MCCBs should be connected with spreader terminals of suitable size.
Material and labour for earthing complete with galvanized steel earth plate electrode size 600x600x6.3 mm thick buried directly in ground vertically in a pit of depth not less than 2.25 mtr below ground levels with top edge of the earth plate not less than 1.5 mtr below normal ground level surrounded from all sides by mixture of charcoal and common salt and electrode connected to and including galvanized iron strip 32 x 6 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanized including GI protection pipe light grade 40 mm dia connected to main earth lead on pole or control board and GI pipe light grade 20 mm dia bore for watering funnel with wire mesh. CI cover with frame, PCC chamber pit with PCC 1:3:6 type C-2 excavation and earth work all as shown in electrical plate No 3 connected to earthing test point all as specified or indicated including testing on completion.
stage.html
html • 0.04 MB
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .