Construction of Ware House for Storage of Electronic voting Machine (EVM) at Reckong Peo in District Kinnaur (HP ) (SH- Building Portion thereof, WS and SI Work ,site development and rain water harvesting system

Amount

Cutting in earth work in all heights and depths and in all kinds of soils including saturated soil comprising of Pick, Jumper , blasting work both in soft and hard rock with chiseling, wedging-out of rock where blasting is prohibited, their intermediate classification of soil, setting-out true to the required lines, grades, side slopes, trimming bottoms to levels as shown on the drawing and as directed by the Engineer-in-charge at site according to HP.PWD, specification of 1990 Vol-I and sorting-out useful/ un –useful materials and stacking the same in all leads and lifts in acquired width of the road and transportation of useful/ un-useful materials for filling in road ways camber, embankments for grades, improvement and leveling to required grade and disposing of all surplus excavated earth in acquired width of the road or on approved dumping sites through all modes of transportion including head load or animal transport or mechanically means alongwith its leveling, fine dressing and all labour, machineries, tools, equipments and safety measures and other incidental, necessary to complete the work by mechanised means and labour if required. All useful materials such as stones , shingles, aggregates and slates shall be sorted- out and stacked along road side, the quantity of which shall not be less then 151.09cum., failing which recovery @ Rupees 300/cum. (Three Hundred per cubic metre) shall be effected from the bill of the contractor. Any loss of the public/ private property during the course of execution shall be absolute responsibility of the contractor which shall to be duly compensated by him in all respect, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (within all lead and lift including dressing of sides and ramming of bottoms, including getting out the excavated soil and disposal of surplus excavated soil as directed, within all leads and lifts in all kinds of soil including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all incidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : all kind of soil including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Centering and shuttering including strutting, propping etc. and removal of form for all heights :form for all heights : including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Foundations, footings, bases of columns, etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platform

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Edges of slabs and breaks in floors and walls

Walls(any Thickness)including attached pilatsters, buttresses plinth and string courses etc.

Providing and Laying concrete for plain/reinforced concrete in open foundations complete as per drawing and technical specification clauses 802, 803, 1202 and 1203. P.C.C (Mechanical mix and vibrated graded crushed stone aggregate) 1:4:8 (40 mm (Forty millimeter) aggregates) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying concrete for plain/reinforced concrete in open foundations complete as per drawing and technical specifications clause 802,803 1202 and 1203. 1:6:12 (One cement : six sand : twelve graged stone aggregate 40mm (Forty millimeter) nominal size, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and laying cement concrete 1:1.5:3 (One cement : one point five sand : three crushed/graded stone aggregate 20mm. (Twenty millimeter) nominal size) mechanically mix by concrete mixer compacting the concrete with vibrator and curing complete excluding cost of form work and reinforcement for R.C.C. work upto plinth level, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels,bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand :3 graded stone) aggregate 20 mm nominal size). including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Reinforced cement concrete work in walls(any thickness),including attached pilasters,buttresses, plinth and string courses, fillets,columns,pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand:3 graded stone aggregate 20 mm)nominal size) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Steel reinforcement (TATA /SAIL / JINDAL PANTHER/RINL) for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level. ThermoMechanically Treated bars of grade Fe-500D or more steel bars including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all ncidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Governmentincluding carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charg

Steel reinforcement for (TATA /SAIL / JINDAL PANTHER/RINL) R.C.C. work including straightening, cutting,bending, placing in position and binding all complete above plinth level.ThermoMechanically Treated bars of grade Fe-500D or more steel bars including entire carriage of materials in all leads and lifts and as per drawings and technical specifications as per the direction of Engineer-in-Charge including all ncidentals.The rates are inclusive of octroi, royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Governmentincluding carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Applying cement slurry on R.C.C. slab or cement concrete work using 2.75 kg. of cement per sq.metre of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and laying cement concrete 1:8:16 (1cement: 8sand:16graded stone aggregate 20mm. nominal size) and curing complete on slab and floor excluding the cost of form work. screed laid under flooring including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Brick work using common burnt clay building bricks in in Cement Mortar 1:6 (1 Cement : 6 Sand) Second Class Bricks in foundation and plinth including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Brick work using common burnt clay building bricks in in Cement Mortar 1:6 (1 Cement : 6 Sand) Second Class Bricks in Superstructure upto all floor level including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Half brick masonry in common burnt clay building bricks inCement Mortar 1:4 (1 cement : 4 sand) second Class in foundation and plinth including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Half brick masonry in common burnt clay building bricks inCement Mortar 1:4 (1 cement : 4 sand) second Class in in Superstructure upto all floor level including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Brick work using common burnt clay building bricks in Superstruture above plinth level in Cement Mortar 1:4 (1 Cement : 4 Sand) Second Class Bricks in Rat Trap Bond Masonary including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Random rubble masonry/polygonal rubble masonry (uncoursed/ brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (One cement : six sand : twelve graded stone aggregate 20mm (Twenty millimeter) nominal size) at plinth level in Cement Mortar 1:6 (One cement: six sand) including curing and including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and Laying stone soling hand packed under floors and placing in position complete upto all floor level including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) 2nd Class Deodar Wood

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws 2nd Class Deodar Wood including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete :20 mm dia including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing M.S. grills (TATA/SAIL/Apollo/JSW Make ) of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing PGI Sheet Lining with butt jointing and nails with necessary screws complete as per Architectural Drawing. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand :6 graded stone aggregate 20mm nominal size). including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coatingnot less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

II) 200x10mm

III) 150x10mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

III) 75mm

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete.Triple strip vertical type including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing oxidized M.S. double acting spring hinges with necessary screws. 150mm including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing bright finished brass hard drawn hooks and eyes :150 mm including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing cup board shutters 25 mm thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked, exterior grade (Grade l Type ll), having one side decorative lamination and other side balancing lamination, including IInd class teak wood lipping of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge

Providing and fixing square edges cover fillets (beading) 19mmx6mm section i/c mitring at junctions with wood screws and nails complete. 1st class Indian teak wood. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in- charge (Frame work shall be paid for separately). 6 mm thick commercial ply conforming to IS : 1328 BWR type including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing 6mm thick cement board ceiling of Everest or its equivalent with standard GI section (GI sections paid to be seprately) complete in all respect including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing & fixing Double glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 5.5 mm thick glass panes including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and laying White glazed tile 6mm thick (30x45 cm )(SOMANY/KAJARIA/NITCO/Orient Bell or its equivalent) in skirting riser of steps and dado 12mm thick cement mortar 1:3 (1cement:3 sand) and jointed with cement slurry complete. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Kota stone slab flooring mirror polished over 25 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab,including rubbing and polishing complete with base of cement mortar 1 : 4 (1cement : 4 coarse sand) : 25 mm thick including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Kota stone mirror polished slab 25 mm thick in risers of steps,skirting dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete and having minimum size of 55x55cm including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Extra for making moulded nosing in Terrazzo/kotastone including returned moulded ends and angles to mouldings. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying Ceramic glazed floor tiles (SOMANY/KAJARIA/NITCO/Orient Bell or its equivalent) of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with greycement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing 0.60mm thick prepainted steel sheet (Tata Durashine or equivalent) in roofing with hot dipped metallic zinc coated sheetwith top coat of regular modifiedpolyster (RNP) organic coating of 20microns over 5 microns primer coating to back coat of polyster of 5microns over 5 microns primer coating i/c fixing with prepainted iron Jor L hooks, bolts and nuts 6mm diametre with prepainted limpet andrubber washers complete with all accesoriees as required as per thedirection of Engineer-in-charge.

Providing and fixing ridges or hips 60cm overall with 0.45 mm thick prepainted steel sheets (Tata Durashine or equivalent) in roofing withhot dipped metalic zinc coated sheetswith top coat of regular modifiedpolyster organic coating of 20 micronsover 5 microns primer coating + backcoat of polyster of 5 microns over 5microns primer coating i/c fixing withprepainted iron J or L hooks, bolts &nuts 6mm dia & prepainted G.I. limpetand bitumen washers omplete withall accessories as required as per the direction of Engineer in Charge. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing Valleys 60cm overall with 0.45mm thickprepainted steel sheets of Tata Durashine in roofing withhot dipped metalic zinc coated sheetswith top coat of regular modifiedpolyster organic coating of 20 micronsover 5 microns primer coating + backcoat of polyster of 5 microns over 5microns primer coating i/c fixing withprepainted iron J or L hooks, bolts &nuts 6mm dia & prepainted G.I. limpetand bitumen washers omplete withall accessories as required as per thedirection of Engineer in Charge.

Providing and fixing flushing 38cm overall with 0.60mm thick prepainted sheet (Tata Durashine or equivalent) in roofing with hot dippedmetalic zinc coated sheet with topcoat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixin g with prepainted iron J or L hooks, bolts and nuts 6mm dia meter & prepainted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing 30 cm wide 120 cm. overall box type gutter with 0.45mm thick prepainted sheet gutter ( Tata Durashine or equivalent)in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating gutter with bolt and nuts and washers etc including making necessary connections with rain water pipe complete as per design. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete .110mm dia pipes including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

1. PVC Plain bend 150mm dia

2. PVC concrete type bend 150mm dia

3.PVC shoe 150mm dia

Providing and fixing bat clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.100 mm diametre

Providing and fixing M.S. BP Sheet 2mm thick in eaves board/ facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Structural steel work (TATA/SAIL/Apollo/JSW Make ) riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including entire carriage of materials in all leads and lifts and as per drawings and technical specifications .The rates are inclusive of octroi,royality, malkana, toll tax, sale tax, GST or other taxes imposed by the Government. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer usingstructural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing in position collapsible steel shutters with vertical channels 20 mm X10 mmX2mm and braced with flat iron diagonals 20 mm X5 mm size with top and bottom rails of T.iron 40 mm X40 mm X6 mm with 38 mm dia steel pulley complete with bolts and nuts locking arrangements,stoppers,handles,including applying a priming coat of red lead paint. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing M.S. tube hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing angle iron door,window,clerestory window frame manufactured from steel iron section MS section 75x40mm and Flat 40x12mm ,including hinges jamb,lockjamb, beed and if required anglethrashold ofmild steel angle 50X25mm welded or rigidly fixed bymechanical means,lugs with splitend tails to each jamb includingsteel butt hinges 2.5 mm thick withprovision for locking arrangementand shock absorber as specified and applyinga coat of approved steel primerafter preteatment of the surface asdirected by Engineer-in- Charge. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing double rebates MS channel iron doors window clerestry window framminfg manufacturing framme MS section 75X40 mm and MS FLAT 40x10 mm as per direction of Engineer- In -Charge and apporoved drawing including hinges lock jambs beed and if require angle thrash hold of mol;d steel angle 50X25 mm welded or rigidly fixed by mechanically means lugs with split and tails to each jambs including steel but hinges 2.5 mm thick with provision for locking observer as specified and applying a coat of approval steel primer after pre-treatment of the surface .

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting Readymixed paint brushing wood primer pink including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Painting two coats(excluding coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping With enamel paint other than white including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Applying priming coat over newsteel & other metal surfaces after& including preparing the surfaceby thoroughly cleaning oil greasedirt and other foreign matter andscoured with wire brushes fine steel wool scrapers and sand papercomplete. With ready mixed priming pain tbrushing red lead,Red-oxide/zincoxide chrome. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Applying priming coat on new concrete/masonry/asbestos cement/plastered surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matter and sand papering as required with :- Readymixed primer including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

6 mm cement plaster of mix :1:3 (1 cement : 3 fine sand) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

15mm Cement plaster in single coat on the Fair side of brick/ concrete/ stone walls for interior plastering upto floor two level including arrises,internal rounded , chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement Mortar 1:6 (1Cemen t: 6 Sand). including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

15mm Cement plaster in single coat on the rough side of brick/ concrete/ stone walls for interior plastering upto floor two level including arrises,internal rounded , chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement Mortar 1:6 (1Cemen t: 6 Sand). including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

15mm Cement plaster in pattern in single coat on the Fair side of brick/ concrete/ stone walls for interior plastering upto floor two level including arrises,internal rounded , chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement Mortar 1:6 (1Cemen t: 6 Sand). including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Distempering with oil bound distemper of approved brand and manufacture (two coat) and of required shade on decorated wall surface to give an even shade over and including a primiming coat with distemper of approved brand and manufacture after thoroughly brushing the surface free from mortar droppign an other foreign matter and also including preparing the surface even and sand papered smooth with primimg caot with distemper primer. Synthetic/Acrylic distemper of asian brand or its equivalent. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Distempering with oil bound distemper of approved brand and manufacture (two coat) and of required shade on undecorated on ceiling and/or sloping roofs to give an even shade over surface to give an even shade over and including a primiming coat with distemper of approved brand and manufacture after thoroughly brushing the surface free from mortar droppign an other foreign matter and also including preparing the surface even and sand papered smooth with primimg caot with distemper primer. Synthetic/Acrylic distemper of asian brand or its equivalent.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete in Super-structure for all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Wall painting (two coats) withplastic emulsion enamel paint ofapproved brand and manufactureon undecorated wall surfacesto give an even shadeincluding thoroughly brushingthe surface fre from mortardroppings and other foreignmatter and sand papered smoothincluding applying of putty asrequired for making thesurface. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Supplying and fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with 4.0 mm thick glass panes including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing & Laying 23 cm Dia Half Round Stone ware pipein CM 1:6 complete as per direction of Engineer-in-Charge. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Proviing and laying in trenches galvanised mild steel tubes including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

15 mm dia nominal bore

20 mm dia nominal bore

32 mm dia nominal bore

Construction chamber 300mm x300mmx500mm inside size for stop cock withC.I. surface box 100mm x 100 mm x75mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 sand 4graded stone aggregate 20mm nominal size) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Constructing chamber 600mm x 600mmx750mm inside size for fire hydrants with C.I. surface box 350mmx 550mm top and 165 mm deep (inside) with changed lid and RCC top slab 1:2:4 mix (1 cement : 2 sand 4 graded stone aggregate 20mm nominal size) 100mm thick foundation concrete 1:5:10 ( 1cement : 5 sand : 10 grades stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :3 sand) finished with a floating coat of neat cement including curing complete :- With 150 mm thick walls of reinforced cast in situ plain cement concrete walls in 1:2:4 mix (1 cement:2 sand : 4 grades stone aggregate 20 mm nominal size complete with form work and reinforcement with 6mm bars not exceeding 150 mm centres both ways. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Making coneection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete: 25to 40mm nominal bore including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete ( cost of water meter and stop stop cock to be paid seprately). including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing white vitreous china pedestal type water closet (European type) (Asian Granito/CERA/HINDWARE/PARRYWARE or its equivalent) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :Providing and fixing white vitreous china pedestal type water closet with seat and lid including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 100 mm size 'P' or 'S'trap for water closet ( squatting pan)includingjointing the trap with the pan vitreous china including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing wash basin with C.I. brackets,Asian Granito/CERA/HINDWARE/PARRYWARE or its equivalent) 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing vitreous China pedestal for wash basin complete in white shade of Hindware or equivalent. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing rubber plug for sink /wash basin :- including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 32mm dia

Providing and fixing C.P. Brass waste for wash basin or sink :- including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 32mm dia

Providing and fixing PVC waste pipe for washbasin /urinals /sink including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 32mm dia

Providing and fixing M.I. Union for wash basinor sink :- including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 32mm dia

Providing and fixing C.P. Brass S. Trap for wash basin and sink including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 32mm dia

Providing and fixing 100mm sand cast irongrating for gully, floor or Nahni trap. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing 600mm x 450 mmbevelled edge mirror of superior glass including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing C.P. Brass Towel rail complete 750mm x 20mmm including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing 600mm x 120 mm glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P.Brass screws including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing Toilet Paper Holder C.P Brass including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing chromium plated brass soap dish including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing CP brass bib tap with capastan head 15mm dia. of Jal or its Equivalent including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing C.P Brass pillar tap with Capstan head 15 dia.of Jal or its Equivalent including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing Brass stop cocks 15mm diaof Jal or its Equivalent including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing C.P. brass angle valve 15mmof Jal or its Equivalent including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing P.V.C connection with brass unions 300/450mm length including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing brass full way valve with wheel 20mm dia. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing G.I./M.I Union of following sizes (where not included in the items . including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing Plytheline – Aluminium -Polyethylene (PE-AL-PE) composite pressure pipe U.V. stabilized with carbon black confirming to IS-15450-2004 of KITECn or tis equivalent water supply including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 1620mm (20mm OD pipe)

II) 1216mm (20mm OD pipe)

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

A) Equal TeeI) 1216

B) Reducing Tee I) 1620 x all branches

C) Female branch TEEI) 1216 X 1216 X 15 mm thread

II) 1620 X 1620 X 20 mm thread

D) Female elbowsI) 1216 X 15 mm thread

II) 1620 X 15 mm thread

E) Male thread connectorI) 1216 X 15 mm thread

II) 1620 X 15 mm thread

F) Female thread connectorI) 1216 X 15 mm thread

II) 1620 X 15 mm thread

G) CouplerI) 1216

H) Reducer I) 1620 X 1216

Providing and fixing PVC water storage tank of ISI : 12701 marked including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing PVC floor trap ISI markedof self cleaning design 110 mm X 75 mm. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing high pressure PVC spigotand socket, waste and ventilating pipes ISImarked including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 75mm dia.

II) 110mm dia.

III) 150mm

Providing and fixing PVC single equal branchwith oval access door, ISI marked insertionrubber washer 3 mm thick bolts and nutscomplete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 150mm dia

II) 110mm dia

III) 75mm dia

Providing and fixing PVC door bend with ovalaccess door, insertion rubber washer 3 mmthick bolts and nuts ISI marked complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 150mm dia

II) 110mm dia

III) 75mm dia

Providing and fixing PVC collars ISI marked including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 150mm dia

II) 110mm dia

III) 75mm dia

Providing and fixing PVC plain bend ISI marked including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 150mm dia

II) 110mm dia

III) 75mm dia

Providing and fixing PVC double equal branch with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 150mm dia

II) 110mm dia

Providing and fixing PVC plain double equal branch ISI marked including fixing with approved adhesive etc. complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 150mm dia

II) 110mm dia

Providing and fixing PVC Clamps ISI marked of approved design with steel screws and rawl plugs etc complete. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 150mm dia

II) 110mm dia

Providing and fixing PVC Cowl ISI marked including jointing the cowl with the PVC pipe with approved adhesive etc. complete. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 150mm dia

II) 110mm dia

Providing and fixing PVC reducer ISI markedincluding jointing with approved adhesive etc.complete. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 150 mm X 110 mm dia.

II) 110 mm X 75 mm dia.

chase in stone / brick masonry walls for fixing sand cast iron / cast /spun iron pipes and fittings including making good the same with stone / brick work in cement mortar 1:3 ( 1 cement : 3 sand) : including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 150mm dia

II) 110mm dia

Providing and fixing PTMT ball valve ofapproved quality and colour.15mm nominal bore including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing PTMT jet spray ofapproved quality and colour with onemetre tube. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing C.P. Bottle Trap for wash basin and sink including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

I) 32mm dia

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing CI underground type fire Hydrant Hydrant confirming to IS 909:- including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing Box (Surface) For Fire Hydrant weight 30 / 31 Kg. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing weapholes PVC in brick masonry / stone masonry /plain reinforced concrete abutment, wing wall, return wall with 100 mm dia PVC pipe extending through the full with of the structures with slop of 1(v):20(H) towards drawing face complete as per drawing and technical specification clauses 614, 709, 1204.3.7 including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 with granular material including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing Providing and fixing Smart Electric razor Wire coil fencing with punch tap Boundary wall i 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately) ncluding all accessories and fittings complete in all respect as per direction of Enginner -In-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand) : 6 graded stone aggregate 20 mm nominal size) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 Circular shape 450 mm internal diameter including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and fixing 75mm dia . PVC Cowl including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Tenzin Construction Co. Pvt. Ltd.