REPAIRS AND MAINT OF WATER TREATMENT PLANTS PUMPS MOTORS AND CONNECTED WORKS UNDER GE BRICHGUNJ SVP

Amount

165 HP, 415V 3 Ph pump motor set

75 HP, 415V 3 Ph pump motor set

50 HP, 415V, 3 Ph pump motor set

40/38 HP, 415V, 3 Ph pump motor set

25 HP, 415V, 3 Ph pump motor set

20 HP, 415V, 3 Ph pump motor set

12.5 Hp to 15 HP, 415V, 3 Ph pump motor set

7.5 HP, 415V, 3 Ph pump motor set

5 HP, 415V, 3 Ph pump motor set

3 HP, 415V, 3 Ph pump motor set

2HP, 415V, 3 Ph pump motor set

1 HP, 3 Ph pump motor set

Upto 2 HP, Single phase pump motor set

75 HP motor.

50 HP motor.

25 HP motor.

20 HP motor.

15 HP motor.

12.5 HP motor.

7.5 HP motor.

5 HP motor.

3 HP motor .

2 HP motor.

1.0 HP motor

Upto 2.0 HP motor single phase.

M&L, painting of monoblock pump set/centrifugal pumpsets including induction motor of any types with one coat of synthetic enamel paint by using spray gun machine after removing all dust and rust and writing date of painting with black synthetic enamel paint complete all as directed.

Upto 3 HP, pump motor set

5 Hp to 10 HP, pump motor set

12.5Hp to 15 Hp pump motor set

20Hp to 25 Hp pump motor set

S&F Bearing for the following pump motor sets/air compressor for the follwing capacities complete all as specified and as directed.

75HP, 415V 3 Ph pump motor set

50 HP, 415V, 3 Ph pump motor set

25 HP, 415V, 3 Ph pump motor set

20 HP, 415V, 3 Ph pump motor set

10 to 15 HP, 415V, 3 Ph pump motor set

5 to 7.5 HP, 415V, 3 Ph pump motor set

Upto 3 HP, 415V, 3 Ph pump motor set

Upto 3 HP, single phase pump motor set

S&F following spare parts for centrifugal pump set of 3 to 7.5 HP capacity complete all as specified and as directed.

CI Impeller

Pump shaft

CI Shaft sleeve

Gasket Packing Sheet

Gland packing (Both side)

Impeller key

SS Coupling

Coupling key

CI shaft Bush

MS Stud with nut

S&F following spare parts for centrifugal pump set of 10 to 25 HP capacity complete all as specified and as directed

CI Impeller

Pump shaft

CI Shaft Sleeve

Gasket Packing Sheet

Gland packing (Both side)

Impeller key

SS Coupling

Coupling key

CI Shaft Bush

MS Stud with nut

Taking down/dismantling deisel driven engine pump of capacity upto 10 BHP from base for servicing by mean of replacing fuel & oil filter, air cleaner, with suitable allignment if required inclding clamps, nuts and bolts and re-install after reaparing complete all as directed

M&L for repair / servicing of suction sweeping machine, pump set mono block 2HP, 3 Phase,415 Volts 50 Hz including oiling/greasing and provn of new gland packing etc for its smooth functioning including replacement of unsv spare parts complete all as specified and as directed.

S&F replacement suction sweeping brush & kit of stainless steel with provision for connection of PVC pipe for water in and out along with tyre wheel and nylon rope 50 mtr length for moving/ pulling of the sweeper all as specified and directed

M&L for disconnecting and removing the unserviceable monoblock pump set and supply ,install the Induction mono block pumpset by arranging dummy plates to suction and delivery line, S&F new pumpset complete with head range 24-36M, disch 12 LPS alongwith with one suitable starter and connecting up complete all as specified and directed.

All as per Item Sl No 10 here-in-before but head range 24-39M, disch 7.58 / 3.3 LPS complete all as specified and directed.

All as per item No. 11 above but 1 to 3 HP submersible pump set.

M&L for removing burnt windings, cleaning, re-winding with approved quality/size super enamel insulated copper winding wire, replacing old insulating materials for 7.5 HP submersible motor complete all as sepcified and directed.

All as per item No.12 Above but capacity 5 HP

All as per item No.12 Above but capacity 3 HP

All as per item No.12 above but capacity 1 to 1.5 HP

Supply only the following spare parts suitable for 3 to 7.5 HP submersible pump set.

Impeller with MS Key

Rotor

Pump shaft with coupling

Oil Seal Thrust bearing

GM Bush.

M & L for suction of muddy particals/slugs through machanical compresssor from the bore well of size upto 150 mm dia all as directed. Note : Cost of Labour for lowering & Lifting of submersible pump set with column pipe is measured under Item no.11 & 11.01

S&F GI column pipe medium grade 40mm bore, each threaded both ends and with coupling (socket) complete all as specified and as directed

All as per item No 15 here-in-before but of size 50 mm dia complete all as specified and as directed

M&L for dismantling of existing foot valve, 40mm to 100 mm bore from UG sump, pump suction line for repairing/ servicing such as cleaning with & including replacement of foot valve sheet, nuts,bolts & washers etc as required and reassembling/ refixing to make it functional complete all as specified and as directed .

All as per Sl item No 16 here-in- before but 150 mm to 200 mm bore complete all as specified and as directed.

S&F in replacement of Gun Metal Foot valve of 80 mm bore including necessary bolts and nuts complete all as specified and as directed

All as per item No 17 here in before but 40/50 mm bore complete all as specified and as directed.

All as per item No 17 here in before but CI foot valve of size 100 mm bore complete all as specified and as directed.

All as per item No 17 here in before but CI foot valve of size 150 mm bore complete all as specified and as directed.

S&F in replacement automatic star delta starter 415V for the motors of 25 HP complete all as specified and as directed by Engr-in-Charge. Make: L&T or equivalent

All as per item No 19 here-in-before above but 20 HP complete all as specified and as directed.

All as per item No 19 here-in-before above but 10 to 15 HP complete all as specified and as directed.

S&F in replacement of DOL starter 415V for the motors for the capacity of 7.5 HP complete all as specified and as directed. Make: L&T or equivalent in BCH

All as per item No. 20 here-in-before but 3 - 5 HP complete all as specified and as directed.

All as per item No. 20 here-in-before but starter upto 3 HP , 240 V complete all as specified and as directed. Make: L&T or equivalent

S&F in replacement star coupling with bolt and nuts and aligning the pumpset properly for 75 HP capacity pumpset complete all as specified and as directed.

All as per item no. 22 here-in-before but capacity 50 HP complete all as specified and as directed.

All as per item no. 22 here-in-before but capacity 20 HP /25 HP complete all as specified and as directed.

S&F in replacement rubber coupling assembly of suitable size for pump set of capacity 20 to 25 HP with including making alignment and testing complete all as directed

All as per Sl item No 23 here in before but capacity 10 to 15 HP complete all as specified and as directed.

All as per Sl item No. 23 here in before but capacity 5 to 7.5 HP complete all as specified and as directed.

S&F in replacement of openwell submersible pump set suitable for 415 volts, 3 phase, 40M Head, 9.5 LPS capacity not less than 10 HP with necessary starter complete all as specified and directed.

Supply only flexible green colour hose pipe with 3 Nos clamp for openwell submersible pump of size 80 mm dia complete all as specified and as direted

M&L for carrying out repairs to unserviceable Altoch based dozing pump including replacement of unserviceable parts and testing complete all as specified and as directed. Note: Spares parts required to replace shall be measured & paid separately.

Supply only PVC Dosing head assembly with suction and delivery adopter with NRV for 25 LPS complete all as specified and as directed.

Supply only PVC NRV set with glass ball for suction and delivery adopter complete all as specified and as directed.

Supply only PVC Adopter for suction and delivery with out NRV complete all as specified and as directed.

Supply only PVC Strainer washer type heavy duty or Y type strainer for suction complete all as specified and as directed.

Supply only Teflon gland square type 3mm complete all as specified and as directed.

Supply only Chemical oil seal with cap complete all as specified and as directed.

S&F in replacement of CI Butterfly valve as per existing make of following sizes as per IS 13095, PN 1.6, suitable for clamping between flanges, including flanges, fittings, gasket, nuts, bolts, washers etc, taking up /down of existing unsv butterfly valve of any description complete of size 50 mm all as specified and directed.

All as per Item Sl No 30 here-in-before but 65 mm dia complete all as specified

All as per Item Sl No 30 here-in-before but 80 mm dia complete all as specified

All as per Item Sl No 30 here-in-before but 100 mm dia complete all as specified

All as per Item Sl No 30 here-in-before but 150 mm dia complete all as specified

S&F in repalacement non return butterly valve ISI marked including jointing materials and necessary joints and nut bolts with washer for flanged ends of size 150 mm complete all as specified and as directed.

All as per Item Sl No 31 here-in-before, but of size 100 mm dia complete all as specified

All as per Item Sl No 31 here-in-before, but of size 80 mm dia complete all as specified

All as per Item Sl No 31 here-in-before, but of size 65 mm dia complete all as specified

All as per Item Sl No 31 here-in-before, but of size 50 mm dia complete all as specified

M&L in repair for openning of gland packing coupling and removing the unsv gland rope from sluice valve of size 80mm to 200 mm dia and fixing the new gland rope all as per existing size gland rope and changing rusted nut bolts washer etc complete all as specified and as directed.

S&F in repairs three phase, 415V 50 Hz Monoblock Pump of capacity not less than 2 HP, head range 8-24 mtr discharge 5.3-3.1 LPS with suitable DOL starter all as specified and as directed

S&F in repairs single phase 230 V 50 Hz Monoblock Pump of capacity head 14 to 18 mtr, discharge 3.6 to 2 LPS with suitable starter all as specified and as directed

S & F Single Phase Preventor suitable for submersible/pump set starter complete all as specified. Make :Minilac or eqvt.

M&L for fabrication of MS sheet not less than 3 mm thick for valve chamber cover with plates of Fe 410W, Gde E-250, Quality-A Plain or chequered channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment with riveted, bolted or welded attachment for locking arrangements complete including painting with two coat of synthetic enamel paint black colour/shade over a coat of redoxide primer complete all as specified and directed.

M&L in rep of schematic diagram board for updatation for water supply installations distribution, details for pump motor of water supply installations duly framed with lamination sheet cover appropriate size as directed by Engr-In-Charge.

S&F in repairs pneumatic solenoid valve as per sample for STP and other installations all as specified and as directed

Supply only Os1 microorganism culture for waste water treatment (01 ltr bottle pack) and bioremedian efforts all as specified and as directed

Supply only and Top Up Gear Oil, SAE: 90 suitable oil for Air Compressor/Gear Pump as per sample all as specified and as directed.

S&F in replacement of pressure switch of pressure pumpset of capacity upto 1.5 HP all as specified and as directed

S&F in replacement LED street light fitting 45 watts with electronic driver and LEDs housed in pressure die cast aluminium housing with toughened glass, IP66 including GI bracket 32mm dia medium grade, suitable MS clamps (02 Nos) nuts, bolts and washers complete all as directed.

Supply only Ortho Tolidine solution in 500 ml bottle pack.

S & F in replacement of Amp Meter 0 to 100 Amp of size 96 x 96 mm digital type complete all as specified and directed.

S & F in replacement of Volt Meter 0 to 500 Volts of size 96 x 96 mm digital type complete all as specified and directed.

S&F in repair LED type indicator lamp unit of red/ yellow/ blue/ green complete all as specified and directed.

M&L for repairing the Existing LT Panel / Feeder Pillar Box any type or size by taking proper shut down, disconnecting and reconnecting all cables with lux, welding / drilling etc complete all as per directed and as specified by Engineer in Charge.

S&F in replacement MCCB, 4 pole, 250 Amps with breaking capcity 36 KA , 415V ,including provision of copper cable/ extended terminals of suitable ratings from MCCBs to busbar and connection of LT cables with MCCBs with lugs/thimbles of suitable size in existing panels complete all as specified and directed by Engr-in-Charge.

All as per Item Sl No 49 here-in-before but MCCB 200 Amp 36 KA 4 pole adjustable type 415 Volts 50 Hz complete all as specified.

All as per Item Sl No 49 here-in-before but MCCB 160 Amp 36 KA 4 pole adjustable type 415 Volts 50 Hz complete all as specified.

All as per Item Sl No 49 here-in-before but MCCB 100 Amp 16 KA 3 pole adjustable type 415 Volts 50 Hz complete all as specified.

S&F "V" belts of size A1585 LP/A61 and size A1458 LP/A56 for complete all as specified.

Supply only High performance polyurea grease for electric motors & High speed ball bearings at medium and high temperatures all as specified and as directed

S&F in repair unsv bimetal over load relays of STPs including connecting and testing complete all as specified and directed.

S& F in replacement Pressure Booster Pump/motor electric driven 220 Volts, SP suitable for 20/25 mm bore, including starter head range 54-10.5m/discharge 15 - 92 lpm all as specified and directed.

S& F in replacement new generation post top lantern for 360 degree indirect light with driver and lamp complete with power LEDs of 40 Watt as light source all as specified and directed

M&L for trimming vegetation or small inequalities clearing all grass, saplings, shrubs, brushwood, roots, and shrubs & vegetation in water supply installations, Pump Houses etc including and removing rubbish upto a distance of 50 meters outside the periphery of the area complete all as specified and as directed.

M&L to collect the sample of water in presence of JE E/M/ Engr-in-Charge from STPs, Pump Houses in fresh Jar Cane and sending it same day to Govt approved lab for testing of various parameter as per relevant IS and submitted test reports complete all as specified and as directed.

S&F in replacement / wiring FRLS PVC insulated industrial grade copper conductor wire of Size 10 sqmm, single core, 1100 volts complete all as specified and as directed.

All as per Item Sl No 57 here-in-before, but size 16 sqmm complete all as specified

All as per Item Sl No 57 here-in-before, but size 25 sqmm complete all as specified

S&F in repairs power contactor 415 volts, 140 Amps, 3 pole including auxiliary contact with Add on block suitable to match the existing contractors complete all as specified and as directed .

All as per Item Sl No 58 here-in-before, but capacity 95 Amps complete all as specified.

All as per Item Sl No 58 here-in-before, but capacity 80 Amps complete all as specified.

All as per Item Sl No 58 here-in-before, but capacity 70 Amps complete all as specified.

All as per Item Sl No 58 here-in-before, but capacity 50 Amps complete all as specified.

S&F in replacement Add on blocks for MNX contractor complete all as specified and as directed .

S&F in replacement MN 5 Motor protection relay for protections of earth fault, thermal overload, single phasing , relay range 45A to 75A, complete all as specified and as directed.

M&L for MS Pipe of of any size 50 to 200 mm bore, plain end, screwed and socketed ends as per IS:1239 heavy grade with all fittings like elbow, tee reducer, flange nut bolt with washer including cutting, welding and joining etc as per site requirement and applying two coats of synthetic enamel paint of approved colour over a coat of red oxide primer including taking up / down of existing unsv pipe of any description complete all as specified and directed.

S&F in replacement connecting, jointing, testing and commissioning of 100mm dia of DI pipes, flanged end for suction line length as per site requierment including jointing material, nuts, bolts and washers etc complete all as specified and directed.

S&F in repair Air Circulating fan suitable for on working of AC 230 V ,50 Hz 450 mm sweep heavy duty with steel metal body, incl louvers complete all as specified.

S&F in replacement of 20mm CPVC pipes SDR 13.5 & Plain CPVC SDR 13.5 grade with all types of fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc as required at site,including taking down the old unsv pipes fittings on walls/ceiling or laying in floors complete all as specified and directed .

All as per Item No 64 here-in-before but of 25mm CPVC pipes complete all as specified

All as per Item No 64 here-in-before but CPVC pipes of outer dia 40 mm

All as per Item No 64 here-in-before but CPVC pipes of outer dia 50 mm

All as per Item No 64 here-in-before but CPVC pipes of Inner Dia 62.50 mm

All as per Item No 64 here-in-before but CPVC pipes of Inner Dia 75 mm

M & L Earthing complete with Galvanised Steel Earth Plate Electrode 600 X 600 X 6 mm thick burried directly in ground [earth pit not less than 2.25 m deep below ground level] with top edge of Plate not less than 1.50 m below normal ground level connected to 32 X 6mm GI Strip [Earth Lead] and GI pipe 50 mm, Medium Grade for earthing lead protection to the extent of maximum 7.5m, Earth Plate Electrode surrounded by 150mm thick packed layers of Charcoal and Common Salt filled in alternate layers, connected to the Plate by means of GI Bolts & Nuts complete all as per Electrical Plate No. 3 of SSR Part – I, connected to panel / DB including testing on completion including main earthing, Charcoal, Common Salt, PCC [1:2:4, Type B1] Pit with RCC 1:2:4, Type B1 Cover, 50 mm thick with 6 Nos, 8 mm dia TMT bars in both ways, MS frame made with 40 X 40 X 6 mm Angle Iron, MS Funnel with 20 mm bore, medium grade GI Watering pipe, wire mesh, earth work excavation, return filling, removal of surplus soil etc. complete all as specified and as directed.

All as per Item No above 35 but using 4mm dia GI wire as earth lead complete all as specified and as directed.

M & L in repair for Earth continuity conductor or main earthing lead of 32 x 6 mm galvanized iron strip, buried in ground or fixed to wall in repair complete all as specified and as directed.

M&L for removing the sewage submersbile pump set from existing position, Shifting to authorised workshop for repair work, overhauling and servicing of pump set with motor incl replacement of unsv nuts, bolts & washers, seals, packing, opening of delivery casing volute for checking of non clog type impeller checking & replacement of stuffing box unit seals and match seal housing /casing cover checking of seat & replacement of seat ring, greasing of flower bearing of pump set, incl cleaning of 3 phase electric submersible squirrel cage induction motor in water tight housing testing it for its water tightness by air for its joints incl replacements of unsv parts as required re-assembling the pump set of capacity upto 3 HP complete all as specified and directed. Note :- Spares parts will be measured and paid under relevant items separately all minor consumable/ Eqpt/Tpt required shall be deemed as included in the rates quoted

M&L for taking out old burnt winding of stator and rotor, cleaning the slots and re-winding of sewage submersible motor with suitable gauge super enamelled copper winding wire, varnishing, insulation, ovening, greasing, including properly fixing of terminal box, upto capacity 3 HP complete all as specified and as directed.

Supply only following spares suitable for 3 HP non clog submersible pump set complete all as specified and directed.

Upper/lower or back to back roller or Ball bearing

Mechinical seal carbonite

Oil seal

Non Clog Impeller

S & F Sluice Valve, Cast Iron body, Stainless Steel Spindle, Gun Metal Rings including Wheel for operation, Flanged and Drilled, 150 mm bore of pipe, confirming to IS - 14846, Class PN -1.6, Long Body type including all Joints with Rubber Gasket and Jointing Materials, Bolts, Nuts, Washer complete all as specified and as directed.

All as per Item No 70 here in before but 100mm bore bore pipe complete all as specified.

All as per Item No 70 here in before but 80 mm bore bore pipe complete all as specified.

M&L for PCC (1:2:4) Type B-1, using 20 mm graded stone aggregate as in foundation, filling mass concrete, for supporting / encasing of Pipe lines of any description, including necessary form work etc complete all as specified and directed.

S&F in replacement Gun metal gate valve with iron wheel head screwed both ends for pipe of size 25 mm all as specified and as directed. Make : Zoloto, LEADER or eqvt.

All as per Item Sl Item No 72 here-in-before but of size 40 mm complete all as specified

All as per Item Sl Item No 72 here-in-before but of size 50 mm complete all as specified

S&F insulation rubber mat of size 1.0m x 2.0m x 12 mm suitable for LT Supply complete as specified and directed

S&F in replacement flat 3 core PVC insulated, Submerssible copper conductor cable of size 4 sqmm including necessary connections complete all as specified and as directed.

All as per item No 74 here-in-before but cable of size 2.5 sqmm complete all as specified and as directed. NOTES :- 1. The contractor or his authorised representative shall report to water supply complaint cell /JE E/M or Engineer-in-Charge at 0900 hours daily on all working days to receive order/instructions of the work or regular complaints. A register shall be maintained to record all orders & instructions and their complaints and is to be signed by the contractor/his representative and the JE EM/ Engr-in -Charge. 2. In case the contractor fails to attend/rectify the defects within the time limit as given by Engr-in-Charge, penalty will the imposed as Rs 1000/- per day in case of complaints/jobs.

Kakolil Trade Agencies (BID ID -3489611)

KAPOOR AUTOMOBILES (BID ID -3491108)

Chandra Construction Enterprises (BID ID -3507453)

Ravi Enterprises (BID ID -3507300)

Prasur Electricals & Engineering Co. (BID ID -3491180)

MGP Enterprises (BID ID -3496015)