REPLACEMENT OF OLD VINTAGE FILTRATION PLANT ALONGWITH CONNECTED ACCESSORIES AT SWIMMING POOL IN ARTY CENTRE UNDER GE NASIK ROAD CAMP.

Amount

Taking down Old unserviceable CI pipe of size 300 mm dia including fittings complete all as directed.

Taking down/out Old Filteration plant Consisting of pressure filter and all connected accessories from Swimming pool and depositing to MES Store all as directed by Engineer-in-Charge. (Note : Cost of T & P and Transporation included in Quoted rates)

Taking down/out Old Filteration plant Motors of any capacity from Swimming pool and depositing to MES Store and all as directed by Engineer-in-Charge. (Note : Cost of T & P and Transporation included in Quoted rates)

Taking out old unserviceable LT Panel board of size 0.90 m x 0.9 m including all accessories etc complete all as directed.

Dismantling/taking out unserviceable sluice valve of size 80mm to 300mm bore dia by opening/cutting rusted nuts, bolts etc all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing).

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) incl removing the demolished material out of MOD land complete all as specified.

M&L for coloured Glass mosic tiles (Make Italia or Glasika to match existing tile colour & pattern) fixed over 5mm thick 325 MYK Laticrete adhesive laid with 2 mm spacers and filling joints with MYK Laticrete Grout pressed with rubber trowel to remove excess grout with damp spongs and subsequently with dry rag complete. Note : Tiles shall be approved by Garrison Engineer.

M&L for providing water proofing treatment in Floor of swimming poolare as under :- (a) Cleaning of floor surface area with wire brush/washing after removing of mosaic tiles. (b) Grouting by fixing of 10mm dia Aqua TP grouting nipple upto 75mm(+) depth by drilling with 12mm bore hole & fixing in cement mortar.using DR. MIRACLE WAC@ 5Kg/Sqm average grout prepared by mixing DR MIRACLE WAC powder with water and 2% DR MIRACLE RETROMER(Part'B') by Grouting pump@5-7 Kg/Sqcm pressure. (c) Grouting by 3 stage methodology fixing of 19mm dia AquaTP grouting nipple upto 75mm (+) depth by drilling with 20mm bore hole & fixing in cement mortar. using DR. MIRACLE SS/WAC/RTF*@25 Kg/Sqm average grout prepared by mixing DR MIRACLE SS powder with water and 2% DR MIRACLE RETROMER ( Part'B') by grouting pump @ 10 to 12 kg/Sqcm pressure. (d) Removal of nipple and making fair & fine by using DR MIRACLE HYFLEX [2 Component] @ 4Kg/Sqm(1.5 kg Polymer : 2.5 Kg DR MIRACLE Part 2). (e) Applying AQUAVENT*moisture release system on floors and wall of swimming pool. (Note :- After Execution of Item No. 08 & 09 leakage test shall be carried out by the contractor, if leakage found in swimming pool same shall be done without any Extra cost.)

Supply, Erection, testing and commissioning of Single stage/Horizontal pumps set with prefilter,Thermoplastic injected pump casing. Impeller in noryl with Stainless steel shaft, mechanical seal in stainless steel connected to TEFC induction motor with built-in thermal protection and automatic reset suitable for 190/ 380 volts, 10.0 HP, 3 phase, 50 cycles A.C supply, IP-55 motor protection complete with inbuilt Filter basket in injected plastic material.Flow 125 m3/hr. @ 14-15 Mtrs. Head completed all as directed (Working 2 Nos. , Standby : 1 No.) Note:- (i) The quoted rates includes the cost of T&P required and foundation (ii) The installation of plant from SI Item No. 10.00 to Item No. 25.00 shall be done through OEM only. (iii) The plant shall be tested by IEM / Rep of CWE. Contractor has to arrange the T&P required for the same.

Supply & Fix 160 mm dia. UPVC Suction valve (Butterfly ) with Valve mounting kit in PVC, Complete with PVC stud ends, PVC flanges, Nut bolts and washers complete all as directed.

Supply & Fix 160 mm dia. UPVC Delivery valve ( Butterfly ) with Valve mounting kit in PVC, Complete with PVC stud ends, PVC flanges, Nut bolts and washers complete all as directed.

Supply & Fix 160 mm dia. UPVC Delivery Non Return valve ( Wafer Type ) with Valve mounting kit in PVC, Complete with PVC stud ends, PVC flanges, Nut bolts and washers complete all as directed.

Supply,install ,testing and commissioing Filter (Verticle Type) -Totally anticorrosive filter media 2000 mm dia., Manufactured with fiber glass & polyster resin, fitted with collector arms & diffuser made from unplastisized PVC & polypropelene, capable of accomodating a flow rate of 125 cum / Hour @ 40 cum / Hour / Sqm complete with lid in polyester resin & fiber glass, manual air purge, cap for sand discharge & PVC flanged connection for inlet & outlet completed all as directed

Supply and filling Sillica sand media for filter with granulometry between o.4 & 0.8mm complete all as directed.

Supply and filling Gravel for filter with granulometry between 1-2mm complete all as directed.

Supply and fix Filter Valve battery 5-Valve batteries built entirely in UPVC with flange connections to filters according to DIN standards. Butterfly valves also in PVC supports made of zinc coated steel pipe with antivibration clamps & fixing plugs, Conn. 140 mm Dia. complete all as directed.

Supply, Install, Testing & commissioning 200 mm Dia. X 10 Kg/cm2 uPVC Piping including necessary fitting such as Elbows, Bends, Sockets, Tees, Collars, Nipples, Reducers, Stub Ends, diminishing pieces, Solvent Cement, etc. for Swimming Pool Inlet & Drain & Suction piping, Swimming Pool filtration plant piping, drain pipe along the pipe periphery including all fittings, fixtures and Ceiling/ Wall Support System suitable for following uPVC pipe as specified and directed.

All as per Item No. 18.00 but size of 160 mm Dia. X 10 Kg/cm2.

All as per Item No. 18.00 but size of 110 mm Dia. X 10 Kg/cm2.

All as per Item No. 18.00 but size of 90 mm Dia. X 10 Kg/cm2.

All as per Item No. 18.00 but size of 75 mm Dia. X 10 Kg/cm2.

All as per Item No. 18.00 but size of 63 mm Dia. X 10 Kg/cm2.

Supply and fix Isolation valve (for Pool inlet) 200 mm dia. UPVC Inlet valve (Butterfly) with Valve mounting kit in PVC, Complete with PVC stud ends, PVC flanges, Nut bolts and washers completed all as directed.

Supply and fix Pool Basin Fittings made out of ABS Plastic Concrete floor inlet with s.s. screw flow 12 m3/hr with 2" female and male connection completed all as specified.

Supply, installing, testing and commissioning factory made, Indoor type LT panel board, IP 52, cubicle type, suitable for 415 Volts, 3 Phase, 4 wire, 50 Hz, AC supply system, and tested at CPRI, having alluminium bus bar of suitable capacity with phase and neautral of same size, colour coded for each phase and neutral, insulated on epoxy type insulators. The bottom of the outer shell contains a detachable plate having provn for entry of cable of adequate size with glands, The panel shall be dust and vermin proof, IP-52 class protection and made 2.00 mm thick CRCA MS sheet, powder coated finish over one coat of red oxide primer on outside surface and painted inside with one coats of red oxide primer, both side opening type, ,provision of connecting earth strip from 2 sides, including internal wiring with PVC insulated solid copper conductor cable, IS-694 marked, 1100 volts grade of appropriate size including grouting of panel 45 cm above ground level by providing 90 cm long angle iron frame of size 40x40x6 mm, welded on all the four corners, embedded in pcc 1:2:4 using 20 mm stone aggregate upto 30 cm above ground level complete all as specified and directed including the following accessories:-

Item No. 26.00 Continued :- INCOMING:- (i) MCCB with thermal based release 4 pole ,100 Amps ,50 Hz 25 KA-01 No (I/C) (iii) Digital multi function panel mounted meter for energy monitoring to display Voltage ,Current,Active power,reactive power,apperent power,power factor,frequency and all other paramater including necessary CTs,PTs and fuses and wiring-01 No (iv) LED type /neon type indicating lamp panel mounted type RYB-03 Nos (v) Single Phase preventer-03 Nos OUTGOING:- (i) MCCB 4 pole 40Amp 25 KA thermal based release - 03 Nos (O/G) (ii) Star Delta Starter 10 HP -03 Nos with Contactor (main ,Delta,Star) & Relay (iii) MCCB 4 pole 40Amp 25 KA thermal based release - 01 Nos (O/G) (vi) DOL Starter 2HP -02 Nos with Contactor & relay.

M&L for replacement Earthing complete with galvanized steel earth plate electrode 60 cm X 60 cm X 6.3 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level connecting to the GI strip 32 x 6mm, by means nut bolt, nuts, check nuts and washer of the GI Earth wire protected by provision of GI light grade pipe 40 mm incl provision of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregated with 40 mm thick cover with RCC (1:2:4) reinforced with XPM (weight not less than 4 Kg / Sqm) and frame of angle iron 25mm X 25 mm X 3mm with lugs 2 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, taste point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding than 50 mtr, all as per electric plate No 3 of SSR Part I 2009 and connection to earth test point all as specified incl testing on completion”.

NOTE : - AMOUNT OF SCHEDULE OF CREDIT RS. 10,150.00 WILL BE DEDUCTED FROM TOTAL AMOUNT OF BOQ.

Shree Sai Samarth Enterprises (BID ID -3256494)

Bidder Name

UNITED ENTERPRISES

Shree Sai Samarth Enterprises