SPECIAL REPAIRS TO DSC MARRIED ACCOMMODATION BUILDING P-164 AT TS MAHUL UNDER GE NW MANKHURD

Amount

Demolition of brickwork built in cement mortar including disposal of debris, etc outside MD land complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any thickness, including nainital or similar pattern roof coverings, complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing the debris out side Md land complete all as specified and directed.

Excavation in trenches not exc 1.5m wide and not exc 1.5m in depth for pipes, foundation etc and 10 Sqm on plan and not exc1.5 metre in depth for pits, independent holes etc, including getting out in any type of soil, complete all as specified and directed.

Returning, filling in with approved earth including spreading, levelling, watering, well ramming in layers n exc 25 cm thick, complete all as specified and directed.

Removing excavated material/soil to a distance not exceeting 50 metre and depositing where directed at a level not exc 1.5 metre above the starting point, complete all as specified and directed.

M&L for PCC (1:3:6) type C-2 (using 40mm graded stone aggregates) as in foundations, filling and mass concrete etc, complete all as specified and directed.

M & L for filling of lean concrete 1:5:10 type E2 (using 40 mm graded stone aggregates) for filling in sunken portion, as per requirement, complete all as specified and directed.

M&L for PCC 1:2:4, type -B-1, using 20mm graded stone aggregated as in sub base of sunken floor mixed with WPC in the proportion as recommended by the manufacturer(s), complete all as specified and directed, (Note : WPC will be measured and paid separately as supply only).

M&L for PCC 1:2:4 Type B0 using 12.5 mm graded aggregate in mass concreting , to be carried out to fill the gap at toe beam level of stair case area filling the void/ hole using all appropriate means as required i.e pumps , nozzles ,needle vibrator , after cleaning thoroughly the area of all dust , loose concrete, complete all as specified and directed.

M&L for Pre cast cement concrete block masonry with solid block of grade(C-5) having block density not less than 1800 Kg/cum, exc, 10cm in width and setting in CM 1: 6, complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) as in coping, bed blocks, roof curb, mud stops, coving at junction of wall and chajjas etc including weathering, slightly rounded or chamfered angles, provision of necessary form work, complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for including cutting of the reinforcement to facilitate demolition and removing the retrieved debris out side MD land, complete all as specified and directed.

M&L for TMT steel bars 10mm dia and over in reinforcement cut to length, bent to shape required, including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc, complete all as specified and directed. Note : This item is applicable for new RCC Members as well as for provision of additional steel bars in the existing RCC Members.

M&L formwork to chullah hoods, chajjas, troughs and similar items including edges for fair finished flat surfaces of the concrete, complete all as specified and directed.

M&L for RCC 1:1.5:3 type type A-1 (using 20mm graded stone aggregate) as in chajjas, complete all as specified and directed.

M&L Hardcore of gauge not exc. 63 mm, deposited, spread and levelling in layers not exc. 15 cm thick, watered and rammed to true surface with broken stone or boulder:

Taking down cement or cement lime plaster on brick or stone walls etc including raking out joints, hacking for keys, scrubbing down with water complete all as specified including necessary scaffolding and safety arrangement complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) not exceeding 1.5 Sqm each including taking down grill and stacking for issued under Sch of Credit.

All as per item No 19.0 above but exc 1.5 Sqm but n.exc 4 Sqm each

Taking down the grill not exceeding 2 .0 Sqm each and refixing the same in the same opening after complete cleaning and when the repair work is complete or as and when directed.

Taking down wooden/PVC/Flush shutters of any description exc 1.00 Sqm but n exc 2.00 Sqm each, complete all as specified and directed.

Taking down chowkhats or frames, not exc 1.5 Sqm each with wooden/ flush/ PVC shutters (Without taking off shutters from the frame) including taking down of hold-fasts by cutting/chasing etc from existing surfaces and also taking down of MS Grills (where exists), refixing the same after proper cleaning and when repairs to plaster etc, complete all as specified and directed.

Taking down chowkhats or frames, not exc 1.5 Sqm but not exc 4.0 sqm each with wooden/ flush/ PVC shutters (Without taking off shutters from the frame) including taking down of hold-fasts by cutting/chasing etc from existing surfaces and also taking down of MS Grills (where exists), refixing the same after proper cleaning and when repairs to plaster etc, complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

S&F pre-painted galvalume aluminium zinc coating (55% aluminium + 43.5% Zinc+ 1.5% Silicon) GI based corrugated steel sheets as in roofing / chajja, 0.50mm thick (total coated thickness) of colour as directed by GE, conforming to AS-1397/ASTM A-792 and having tensile strength minimum 550 Mpa fixed with and including hot dip galvanised, self drilling and self tapping screws neoprene and EPDM washers as per manufacturer's instructions, complete all as specified and directed.

S&F aluminium anodised Grills of approved design with and including F/U channel for window, ventilators, balcony opening in architectural or rectangular type in existing building, including drilling as required in RCC sections, complete all as specified and directed. Note: The Grills shall be of Model DG-102/DG-104 of Make Deco or equivalent make as approved by the GE

S&F standard aluminium section anodised shutters for doors, window / ventilators, partitions, fixed / openable / sliding or in any pattern, cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc complete all as specified and directed (Aluminium section shall be of make Jindal/Hindalco/ Indalco) Note:- Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. Cost of other items / accessories required for entire completion of the work shall be deemed to be included in the quoted rate. However glass panes and wire cloth shall be measured and paid separately as supply only under respective items.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supply and fixing in opening as per specification given under SSR Part II 2010 including making good the disturbed surface. Make: Rajashree or equivalent.

M&L for factory made solid PVC panel type PVC door shutter 30mm thick consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rails, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent supplying and fixing in the frame at site as per specifications and drawing given under SSR Part II 2004 complete as as specified. Make : Rajashree or equivalent make as approved.

S&F second class hard wood plain, solid straight chowkats and frame, wrought framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including good the disturbed surfaces of walls complete all as specified and directed .

S&F second class hard wood 35mm thick, plain, framed panelled shutters (any number of panels), with panels of timber flat on both sides (Feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers, fitted to chowkhats complete all as specified and directed.

S&F second class hardwood 35mm thick glazed and skeleton shutters open and prepared to receive glass ,gauze etc (with sash bars) edges of plain, chamferred or rounded, fitted with cut and mitred beads for securing gauzes etc, sizes of members of sizes of shutters as specified in SSR part -I sec 8,cluse 8.24(a).

S&F in repairs 20 mm dia Harrison rails, mild steel, chromium plated, curtain rails with and including fixing brackets, stops, rollers etc, complete all as specified and directed.

Dismantling boarding of any description as in cub-board, shelves etc, complete all as specified and directed.

S&F 25 mm thick factory made Flush shutters, solid core construction with particle board core and plywood face panels, both sides covered with decorative face vaneer, with and including 6mm thick Teak Wood Lipping/frame to match, complete all as specified and directed.

M&L for 12 mm thick, commercial ply for shelves of cupboards of (7 Ply), grade 1 BWR type BB , fixed with screws to timber frame work, complete all as specified and directed.

S&F continuous (piano) hinges, width of flap 30mm (when open), mild steel, bright finish or electro-galvanised, complete all as specified and directed.

S&F 150 mm size hasp & staple, aluminium anodised, safety type, including bolt to hinge plate and fixed with screws, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc, complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates rails braces etc, conforming to Fe-290 (Grade-E-165) complete drilled for fixing of steel sheeting or other coveringc, all as specified and directed.

S&F MS hold fasts and similar small articles complete all as specified and directed

S&F aluminium anodised sliding door bolts with hasp and staple (Bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, length of bolt 300mm complete all as specified and directed.

S & F stainless steel butt hinges with extruded aluminium alloy with galvanised mile steel hinges pins 100mm size complete all as specified and directed.

S & F aluminium anodised barrel tower bolt of extruded section of size 150 mm length complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section and fixed 200 mm complete all as specified and directed.

S & F 150 mm long extruded aluminium alloy handles, fabricated type anodised complete all as specified and directed by Engr-in-Charge.

Supply only 5 mm thick plain sheet glass, ordinary quality, complete all as specified and directed.

Supply and fixing 5 mm thick plain sheet glass, ordinary quality with and including provision of new rubber gasket after hacking out old broken glass (any size, quality or description) for existing aluminium joinery, complete all as specified and directed.

Supply only aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40 mm for new aluminium joinery, complete all as specified and directed.

S& F in repair galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

Dismantling completely existing roof treatment (excluding cement screed bed ) including loosened cement plaster and exposing the top surface of RCC slab and making good the same in CM 1:4 and removing rubbish, etc to a distance exceeding 500 m and not exceeding 1.0 km complete all as specified and directed by the Engineer-in-charge

M & L for APP modified roof treatment over existing roof slab etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying APP modified water proofing membrane reinforced with non woven polyester fibre weight not less than 160 gm/Sqcm using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.50 Kg/Sqm and miniumun thickness 4mm . (ii) Non woven polyester weight not less than 160 gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption - Not more than 1% on mass within 24 hours. (ix) Cold flexibility - Minimum (-) 20C. (x) Dimentional stability % change = Maximum 1%. (d) applying one coat of solar reflective bituminous aluminium paint @ 0.10 Kg/Sqm over APP membrane for non accessible roof complete all as specified and directed.

M&L for 10 mm thick cm layer of (1:3) with WPC when the concrete is still green complete all as specified and directed.

Chipping, removing carefully loose/damaged concrete including plastering (total thickness upto 40mm ) from surfaces of RCC members, in any location by low impact Hammer/Breakar without damaging the structure & cleaning the surfaces with wire brush etc and disposal of debris out side MOD land complete all as specified and directed. Note : 1) Hard concrete shall not be removed by force.

M&L for cleaning existing reinforcement with wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hour between the coats, complete all as specified and directed. (Note :- Mode of measurement: superficial area of concrete will be measured.)

M&L for Anticorrosive Treatment to Reinforcement using Corroseal - ZR of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces complete all as specified and directed. Note :- Mode of measurement: superficial area of concrete will be measured.

M&L for providing additional mild steel TMT bars in various structural RCC members like column, beams and Slab etc. including cutting, bending, fixing the bars, tying with and including binding wire etc., complete all as specified and directed.

M&L for shear connectors of 8 mm dia TMT bars including anchoring of the reinforcement bars in existing RCC member by providing holes of minimum 10d depth and grouting in position with locfix (fosroc), including drilling of holes, cleaning and other relevant works, complete all as specified and directed.

M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR equivalent of M/s. Krishna Conchem as approved by GE over exposed concrete surfaces prior to application of any type of mortar to ensure bond between old concrete & new concrete / mortar by brush application, complete all as specified and directed.

M&L for casting & repairing of excessively damaged distressed RCC members with pre-batched, pre-packed, single component ready to use micro concrete from M/s. Krishna Conchem Molith MC) or equivalent of Dr. Fixit as approved by GE at any level and at any lead or lift as directed including scaffolding , also including mixing , laying, levelling, finishing, curing etc as per manufacturer's specifications complete all as specified and directed. (Note : Reinforcement & formwork shall be only shall be measured and paid separately).

M&L for building up the profile of structural members using polymer modified mortar from M/s. Krishna Conchem (Molith PMM) OR Polymer mortar HB of Dr Fixit, while the bonding agent is still tacking upto 20mm thickness, including levelling, profiling, formworking, scaffolding etc, complete all as specified and directed.

M&L for forrnwork to sides of pillars. Posts, struts, piers, columns and stanchions for fair finished surfaces of concrete, square, complete all as specified and directed.

M&L for building up the profile of structural members using polymer modified mortar of Krishna Conchem (Molith PMM) or polymer mortar HB of Dr Fixit while the bonding agent is tacking upto 40 mm thickness (of 20x20 mm each in 2 layers) including levelling, profiling formworking, scaffolding etc complete all as specified and directed. `

M&L for drillling and fixing 8 mm , 10 mm,& 12 mm re-bars with Fisher/ Hilti or equivalent system and chemical etc. Note : Reinforcement to be paid separately

M&L for drilling and fixing Teflon perforated nozzles in RCC member, including drilling 14 mm dia 50 to 100 mm deep holes in structural members at intervals of 600 mm or 2 nozzles per sqm in staggered manner after cleaning the holes by air blower further the external end of nozzles to be machined to receive outlet of grouting gun ,nozzle is fixed using epoxy sealant to ensure complete sealing and curing the whole affected area for min 12 hours complete as directed by the Engr in Charge and consultants in RCC structural elements.

M&L for injecting low viscosity epoxy resin of Dr Fixit Epoxy injection, EPCO -KP-HP -250 of M/s Krishna Conchem Products Shaligrout EI of STP Ltd with an injection pump, pumping shall be stopped once the pressure is felt and no more epoxy resin can be injected, allow resin to set for at least for 7 days, after cutting the ports/ nozzle, seal the grouting holes using epoxy putty, seal putty shall be ground off with a rotary scrubbing machine.

M&L for coloured 400x200x6mm thick glazed ceramic tiles on vertical surfaces such as skirting, dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with the colour of tiles, over and including 10mm thick cement mortar backing coat in CM 1:4, complete all as specified and directed.

M&L for coloured Non-skid ceramic tiles 7 to 8 mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with in the colour of tiles, over and including 15mm thick cement mortar screed bed in CM 1:6, complete all as specified and directed.

M&L for Non Skid ceramic tiles 7 to 8 mm thick, coloured (squares/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed.

M&L for pre-polished Kota Stone Slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed including moulding/rounding to edges of the slab and also including provision of 10 mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for 20 to 25 mm thick machine cut pre-polished cuddappa stone Slabs (table rubbed and polished) as in shelves and similar things, including moulding/rounding to edges of the slab, complete all as specified and directed.

M&L for pre-polished 20 to 25 mm thick machine cut pre-polished cuddappa stone Slabs (table rubbed and polished) as in cills, jambs, soffits, cooking platform etc, pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of stone slab etc, including moulding/rounding to edges of the slab and also including provision of 15 mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for pre-polished Machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab complete and rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations.

M&L for coloured parking tiles, heavy duty of size 300x300x10 mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match the colour of the tiles, over and including 15mm thick cement mortar screed bed in CM 1:6, complete all as specified and directed. Make : JOHNSAN /SOMANI/ORIENT BELL/KAJARIA.

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types including rounding to edges over 15mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for 12 mm thick polymer modified ready mix cement based plaster on the wall surfaces including finishing surfaces even and smooth, complete all as specified and directed Make: Easy Plast from M/s wall plast or chemplast or ready-plast from Ultratech. Note: The thickness of plaster specified above is the minimum thickness and the quoted rates shall also be deemed to include for provision of dubbing of the surfaces with ready mix plaster and nothing extra shall be payable on this account.

M&L for rendering 15 mm thick in CM 1:6 over fair faces of brick work or concrete surfaces complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar (1:3) to ceiling, finishing the surfaces even and smooth without using extra cement, complete all as specified and directed.

Material and labour for rendering 15 mm thick rendering in CM 1:4 mixed with WPC in the proportion as recommended by the manufacturer(s), over top of sunken floor, roof surfaces etc, finished even and fair, complete all as specified and as directed Note: WPC shall be measured and paid as "supply only" separately.

M&L for leakage / seepage proof coating consisting of preparing the new surfaces of existing exterior walls, parapet walls, chajjas etc. and applying Prime seal primer of M/s Dr Fixit or equivalent chemical of M/s STP Ltd as approved by the GE or one coat of Chemstic PDE 600 elastomeric coating (and allowing to dry for 8hrs) under torch dry condition and subsequently applying two coats of water proofing decorative elastomeric coating system Raincoat of M/s Dr Fixit with DFT 100microns or Shalicryl 215 of M/s STP Ltd or Chemstic PDE 600 elastomeric coating (the surfaces after painting one coat shall be allowed to dry for 6 to 8hours before application of next coat) including necessary scaffolding etc complete all as per manufacturer instructions, as specified & directed. Note: The aforesaid treatment shall be got executed by the contractor from the authorized applicator of the manufacturer(s) and also necessary authenticated documents on account of above shall be submitted by the contractor to the GE.

M& L for preparation of new steel and iron surfaces of any description, over 10cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a priming coat of red oxide zinc chrome, complete all as specified and directed.

M&L for preparation of new or previously untreated wood based surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of old surfaces of walls and applying two coats of oil bound distemper over a coat of primer, complete all as specified and directed.

M&L for 3 mm thick (minimum) white cement based wall care putty in two coats on new or old surfaces of walls/ceilings etc, finished even and smooth, complete all as specified and directed.

M & L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper with roller over one coat of primer, complete all as specified and directed.

M & L for preparation of new plastered surfaces of ceiling and applying two coats of oil bound distemper with roller over one coat of primer, complete all as specified and directed.

M & L for preparation of old plastered surfaces of ceiling and applying two coats of oil bound distemper with roller over one coat of primer, complete all as specified and directed.

S&F in repairs, white, vitreous China, wash down water closet pan (pedestal pattern), Ist quality, including plastic water closet seat white, closed pattern with flat bottom and cover and Mild Steel CP or aluminised hinging device, complete all as specified and directed. Note: Flushing cistern, flush pipe will be measured and paid for separately.

S & F health faucet of 15 mm dia with one metre tube hook , Cat No 187 of Prayag or equivalent make as approved by the GE complete all as specified.

S & F in repairs flushing cistern, 10 Ltrs. Capacity, PVC valveless, syphonic action type with dual flushing system, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of polyethylene of low or high density or PVC, 32mm dia, complete all as specified and directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and as directed.

S&F two way Bib cock of Pryag make Cat No SQT-512 ANKN or of ESSCO or equivalent of Marko, Parko as approved by the GE complete all as specified and directed.

S&F in repairs Vitreous China white, 1st quality, wash hand basin, flat back, size 550mm x 400mm including mild steel angle brackets, CP brass fittings, waste, union, 32mm dia PVC waste pipe, cutting for and pinning ends of brackets, complete all as specified and directed.

S & F for 40 mm dia Low density polyethylene (LDPE) pipes of pressure rating 6kgf/sqcm all as specified and directed.

S&F 15 mm bore brass CP pillar tap, Make ESSCO Cat No MQT-507 or equivalent of make Parko as approved by the GE, complete all as specified and directed.

S&F 15 mm bore brass CP Stop Valve, Make ESSCO Cat No MQT-513 A or equivalent of make Parko/ ZOLOTO as approved by the GE, complete all as specified and directed.

S&F 15 mm bore brass CP Bib Tap, Make ESSCO Cat No MQT-511 or equivalent of make parko as approved by the GE, complete all as specified and directed.

S&F in repairs brass chromium plated, shower rose, 125 mm size with and including 195mm long 15mm bore brass chromium plated shower arm with bend of 45 degree, complete all as specified and directed.

S&F in repair Grating doom 125 mm dia with waste hole of PTMT (Minimum Weight 25 gram), complete all as specified and directed.

Taking up or down steel water tubing and connections of size 15 mm bore, complete all as specified and directed.

Taking up or down steel water tubing and connections of size 20 mm bore, complete all as specified and directed.

Taking up or down steel water tubing and connections of size 25 mm bore, complete all as specified and directed.

Supply & fixing 15 mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

Supply & fixing 20 mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed.

Supply & fixing 15 mm CPVC pipes UV stable, leak proof, tough ,rigid , conforming to IS:15778 of SDR 11 standard., medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

Supply & fixing 25 mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

S & F of 75 mm bore uPVC (SWR) soil, waste, ventilating rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including rubber ring joints, complete fixed to wall with necessary PVC standard stay clamps etc, including taking down existing SWR pipes(including fittings) of any description, complete all as specified and directed.

S & F 110 mm bore uPVC (SWR) soil, waste, ventilating, rain water pipe type 'A', single socketed, (ISI Marked) in any length with and including rubber ring joints, complete fixed to wall with necessary PVC standard stay clamps etc, including taking down existing SWR pipes(including fittings) of any description, complete all as specified and directed.

S&F 75 mm bore uPVC (SWR) branch piece single (Single Y), equal or unequal with and including rubber ring joints, complete all as specified and directed.

S&F 110mm bore uPVC (SWR) branch piece, single (single Y), equal or unequal with and including rubber ring joints, complete all as specified and directed.

S&F 75 mm bore uPVC (SWR) Bends with and including oval access door and also including rubber ring joints, complete all as specified and directed.

S&F 110 mm bore uPVC (SWR) Bends with and including oval access door and also including rubber ring joints, complete all as specified and directed.

S&F in repairs Kitchen Sinks made of stainless steel grade AISI-305, 1 mm thick including provision of plugs, washers, brass CP waste coupling/ fittings and 40mm bore PVC waste pipe, mild steel cantilever brackets, overall size 600 x 500 x 200 mm, , complete all as specified and directed.

S&F stainless steel plate rack of size 600x900x250mm, Make Prayag : Cat No P-336 or equivalent as approved by the GE, complete all as specified and directed.

S&F uPVC vent cowl for 75 mm bore pipe with and including rubber ring joints, complete all as specified and directed.

S&F cast iron Nahani trap with 75 mm dia out let including grating, connecting, jointing to waste pipe with lead joints, also including embedding the same in PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) mixed with water proofing compound in the proportion as recommended by the manufacturer(s), taking out existing unserviceable traps by hacking out concrete joints and making good of surfaces, complete all as specified and as directed .

M&L for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.20 Kg/Sqm including cleaning the surfaces over newly plastered surfaces of sunken portion, complete all as specified and directed.

Supply only intergal water proofing compound, complete all as specified and directed.

S&F 20 mm dia brass chromium plated tubular towel rail 'D' type 600 mm long between flanges, complete all as specified and directed.

Dismantling existing water tanks of capacity exc 250 ltrs and not exc 500 ltrs, complete all as specified and directed

Supplying and fixing rotational moulded polyethylene water storage tanks, double layered (ISI marked) of 500 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I, including provision of necessary fittings for connecting the overflow, drain out, inlet and outlet pipes, complete all as specified and as directed.

S&F in repairs gunmetal gate valve, ISI marked with iron wheel head, screwed at both ends for iron pipe or ferrule of 25mm bore and provision of necessary fittings like unions, check nuts, etc, complete all as specified and as directed.

S&F uPVC vent cowl 110 mm bore with and including rubber ring joints, complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortor of any dia, complete all as specified and directed.

M&L for Salt Glazed, Stoneware, Drain pipes of 150 mm bore, grade 'A', laid in trenches and jointed, complete all as specified and directed. Note: Excavation & earth work and PCC for bedding & haunching shall be measured and paid for separately.

M&L for 100 mm thick concrete bed in cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) for 150 mm bore pipes including packing under and haunching against the sides of pipes after they are laid and tested etc, complete all as specified and directed.

Taking down copper/ aluminum point wiring (Light/Fan/Socket or power) complete including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces to walls floors etc.

Taking down complete main switches/DBs with enclosure and its components of any size and capacity etc, complete all as specified and directed.

M & L for point wiring complete with proper colour coding using, 1100 Volts grade, 1.5 Sqmm, PVC insulated FRLS, unsheathed wire with multi stranded copper conductor confirming to IS-694, Part II, ISI marked drawn in and including PVC casing caping (minimum 25mm width) fixed on the surfaces of wall, ceiling etc with all accessories, fittings, PVC junction boxes etc, sunk pressed steel boxes not less than 2 mm thick, 50 mm deep terminal boxes covered with 3mm thick plastic laminated sheet top cover fastended with chromium plated brass screws, also including 1.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts multi-stranded copper conductor green colour as continuous earth wire connected to common earth dolly all as specified and directed for following items. Note rates included for all types of disturbed surfaces making good in CM 1:4 and matching with the existing

All as per item No.132.00 above but for one light point /fan/bell point controlled by one one way switch

All as per item No.132.00 above but for One 2 pin/ 3 pin socket outlet 5 Amps on same board

All as per item No.132.00 above but for One 2 pin/ 3 pin socket outlet 5 Amps on independent board

M&L for point wiring using proper colour coding with 1100 Volts grade, 2.5 Sqmm PVC insulated, FRLS, unsheathed, wire confirming to IS-694, Part-II, ISI marked with multi-stranded copper conductor drawn in and including PVC casing caping (minimum 25mm in width) fixed on the surfaces with all accessories, fittings, PVC junction boxes etc, sunk pressed steel terminal boxes not less than 2 mm thick, 50 mm deep, covered with 3 mm thick plastic laminated sheet top cover fastened with chromium plated brass screws, also including 2.5 Sqmm, PVC insulated, FRLS, unsheathed, multi-stranded, copper conductor 1100 Volts grade, green color, continuous earth wire connected to common earth dolly for 15 Amps, 3 Pin, socket outlet independent, complete all as specified and directed Note rates included for all types of disturbed surfaces making good in CM 1:4 and matching with the existing .

S&F Switch Piano 5 Amps, 250 Volts, one way, flush type, complete all as specified and directed.

Supply & Fix Bell push, flush type, 5 Amp, 230 Volts, complete all as specified and directed.

S&F ceiling rose three terminal, 230 Volts PVC / Polycarbonate body, complete all as specified and directed.

S&F Switch Socket combination 2 in 1 , 5 Amps, flush type, 5 Pin, 240 Volts, complete all as specified and directed.

S&F Switch Socket combination 2 in 1 , 5/15 Amps, flush type, 6 Pin, complete all as specified and directed.

S&F fan regulator, electronic stepped (5 step), 230 volts, 100 watt, flush type and connecting-up, complete all as specified and directed.

Supply and fix bell ding dong AC 230 V single pole complete all as specified and directed.

S & F MCB DB, 8 way, SPN, double door, 240 Volts and including cutting chases in wall, concealing DB in wall, making good the disturbed surfaces and making all connections, complete all as specified and directed.

S & F MCB SPN 32 Amps, 240 / 415 Volts, 50 Hz, 10 KA Breaking capacity, complete all as specified and directed.

S & F MCB, SP, 05 to 32 Amps, 240 Volts, 10 KA Breaking capacity, C-series, complete all as specified and directed.

S&F in Ultra bright glass LED tube rod 18/20 Watts, 230 Volts, with high efficiency suitable for T8 fitting with G13 lamp holder, the rod shall conform to Cat No. CRYSTAL 1213T8DSTL 20 W LED 865 SGLASS of HAVALLS or equivalent from Philips/Crompton Bajaj.

S&F in decorative box type fitting prewired Regal batten for LED light fitting 16/20 Watts, 230 volts, including PVC Mounting blocks - 2 Nos, including connecting up with 1.5 Sqmm White colour PVC insulated three core flexible multi-stranded copper conductor for connecting with ceiling rose. The fitting shall conform to Cat No REGALBATTENT8UPTO1X22WSSBSWH for Havells equivalent from Philips/Crompton Bajaj.

S&F in Retro LED tube rod 8 Watts, 230 Volts, with high efficiency PMMA diffuser, the rod shall conform to Cat No LTT8-8 of Crompton or equivalent from Philips/Bajaj.

S&F decorative box type fitting prewired Retro LED light fitting 8 Watts, 230 volts, including PVC Mounting blocks - 2 Nos, including connecting up with 1.5 Sqmm White colour PVC insulated three core flexible multi-strand copper conductor for connecting with ceiling rose. The fitting shall conform to Cat No DMLN1LT8-8 of Crompton or equivalent from Philips/Bajaj.

M & L for sub main wiring complete with Two runs of 6.0 Sqmm PVC insulated, unsheathed, heavy duty, 1100 volt grade multi-stranded copper conductor cable (FRLS), drawn in and including PVC casing caping fixed on the surfaces of walls, RCC slab/ ceiling/columns / beams etc with all accessories, fittings, PVC junction boxes etc, also including one run of 6 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts multi-stranded copper conductor green colour as continuous earth wire connected to common earth dolly and mains, complete all as specified and directed. Note: Two runs of 6.0 Sqmm PVC cable, one run of 6 Sqmm cable and one run of Casing Caping will be measured as 'one unit' length.

Taking down of existing ceiling fans and re-fixing of the same ceiling fan 1200 mm sweep including provision of cable from ceiling nose/ conductor to fan and spray painting of ceiling fan with two coats of synthetic enamel paint, after preparation of surfaces, complete all as specified and directed.

S & F of security light fitting LED type 45 watts with new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded pc cover having TOP opening separate driver compartment with IP 66 protection and impact resistance and impact resistance of IK 07 etc all as directed by Engineer in charge Cat no - ENDURAPEARLNEOSL45WLED757PASYTOPC of Havells or equivalent Bajaj/Philips.

S& F of GI steel tubing medium grade 40 mm dia and length up to 1.5 meter bent to shape of offset angle upto 45degree for fixing of security /street light fittings including MS clamps made of 25mm x 6mm flat iron, nuts , bolts, etc all as directed by Engineer in charge

Supply and lay cable XLPE insulated screened PVC Bedded ISI Marked, galvanised steel strip or wire armoured, electric power cable(heavy duty) 1100 volts grade with stranded aluminium conductor of size:- 25 Sqmm x 4 core make :- Havels, polycab, indo asian. Safety Certificate : The contractor on completion of work shall submit the safety certificate, duly singed stating that all electrical fitting, wiring, ceiling fan, exhaust fan switch socket, cable panels which have been executed are safe for operation.

Supply and filling for sand cushioning by spreading in trenches fine dry sand by gently punning down manually as in cable protection, complete all as specified and directed.

Supply and laying precast concrete cable cover class LV ISI Marked, type-I, flat size 250mm x 150mm x 40mm laid in trenches all as specified. Make - Methab Tiles or Conforming to IS

M&L for cutting existing road/hard standing not exc 45x45 cm in wide & depth getting out excavated material for laying GI tube, returning filling & well ramming watering finish surface 10 cm from top using PCC 1:3:6; including removal of surfaces soil all as directed

S& F in replacement of GI steel tubing medium grade 40mm dia for laying in ground, along the pole in coping, road crossing etc for cable protection including necessary fittings , clamps for supports, etc all as directed by Engineer in charge, Make - Tata/Jindal/Surya Prakash

Disconnecting the incoming and out going cable connection and dismantling the unserviceable conventional type industrial meter board and removing from site for further disposal. Design fabricating supplying and fixing indoor type vermin and weatherproof totally inclosed cubical type front operated, sufficient ventilation on sides cubicle type fabricated out of 2 mm thick CRCA sheet duly treated with seven tank process and painted epoxy powder coated siemens grey colour and with industrial type built in locking arrangement. The panel shall be factory made from a reputed panel fabricators (CPRI approved manufacturers) in and around Mumbai. The panel shall be wall mounting type and to be fixed on wall with all necessary fixing arrangements such as angle iron brackets and frame. The panel to be prewired with PVC insulated copper conductors appropriate current carrying capacity for connecting the incoming and out going MCCBs and MCBs. including disconnecting the LT panel and taking down the unserviceable cables and including MCBs. Energy meters of the panel shall be taking down and kept in safe custody for re-installation of site. The following shall be provided :- (a) MCCB FP 40 Amps 415 Volt 16 KA - 1 No (Incoming) (b) MCB SPN 40 Amps, 10 KA 415 Volts- 9 Nos (c) RYB Indicators - 1 Set (d) Digital Digital VAF meter - 01 No (e) Space for fixing of 09 Nos single phase electric energy meters (e) Fixing energy meters -09 Nos obntained from the existing panel of respective Qtrs, including making necessary wiring. (f) Danger notice board written in regional language Hindi and English. Make of MCCB,MCB, Shall be - Legrand,ABB,Indo Asian,Siemens,Schnider Electric Note - The lay out drawing of the panel shall be got approved by the contractor before panel fabrication and shall be fabricated from CPRI approved manufacturer

M&L for earthing complete with galvanised earth plate electrode 600 x 600 x 6mm thick buried directly in ground, earth pit not less than 2.25 meters deep below ground level, connected to and including galvanised earth wire 4mm dia to the extent upto 7.5 metre as earth lead by means of bolts, nuts etc, with provision of charcoal and salt all as per electrical plate No 3 of SSR Part I, including water arrangement with GI pipe 20mm bore (medium grade), earth lead protection pipe 15mm bore light grade with bends, elbow etc. from earth plate to test point, excavation and earth work, returning, filling, ramming and removing of soil to a distance not exc 50 metre, making PCC 1:2:4 type B-1 pit (Earth chamber) with RCC 1:2:4 cover 50mm thick reinforced with XPM and testing on completion including making test point on wall as per SSR specifications all as specified and directed. (Note: Cost of GI earth wire and protection pipe upto 7.5 metre shall also be deemed to be included in the quoted rate).

M/s Mohd Altaf Hanif Qureshi