CERTAIN B/R REPAIR WORKS AND OTHER MISC WORKS AT E/M INSTALLATIONS AT AF STN BHISIANA

Amount

B/R WORKS

Taking down cement plaster of any description on Brick Walls, concrete surfaces including racking out joints, hacking for key, scrubbing down with water, remove dust, debries/rubbish etc complete all as specified and as directed by Engineer in Charge.

M&L for Rough cast plaster on brick wall consisting under coat of cement and sand mortar (1:3) not less than 10 mm thick and while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel mixed with coarse sand and cement in the ratio 1:1:1 shall be applied and finish even incl applying two coat of cement base paint over a coat of of primer after preparation of new plastered surface complete all as specified and as directed by Engineer in Charge.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4), using water proofing compound complete all as specified and as directed by Engineer in Charge. NOTE: WPC will be measured and paid for separately

Supply only liquid water proofing comound ISI Marked approved make complete all as specified and as directed by Engineer in Charge.

M&L 10mm thick cement plastering in CM 1:6 on fair faces of brik work or concrete surfaces finished even and fair etc complete all as specified and as directed by Engineer in Charge.

M&L 5mm thick cement plastering in CM 1:3 on fair faces of cocnrete ceiling surfaces finished even & smooth wihtout using extra cement complete all as specified and as directed by Engineer in Charge.

M&L for applying two coat of OBD, white or tinted over a coat of primer incl prepared new plastered surfaces complete all as specified and as directed by Engineer in Charge.

M&L for complete removal of existing treatment and preparation of old plastered surfaces of walls and applying two coats of Oil bound distemper acrylic /distemper oil emulsion acrylic, white or tinted over a priming coat of same make on wall surfaces all as specified and directed by Engineer-in-Charge.

M&L applying 1-2 mm thick wall care putty (JK/Birla/berger) on walls, including making surface even and smooth using sand paper before applying Priming coat,complete all as specified and as directed by Engineer in Charge.

M&L for preparation of old decorated surfaces of ceiling and applying one coats of white wash, complete all as specified and as directed by Engineer in Charge.

M&L for Complete removal of existing treatment on old/new plastered surfaces of walls, pillars, cornices and applying Two coats of premium quality exterior emulsion paint over priming coat of exterior primer complete all as specified and as directed by Engineer in Charge.

M&L Preparing Old Surfaces of Walls and applying one coats of cement base paint , complete all as specified and directed by Engineer in Charge.

M&L for Applying a coat of oil bound distemper over and after preparation of old decorated plastered/unplastered surfaces of walls , pillars cornice etc complete all as specified and directed by Engineer in Charge.

M&L for Preparation of surfaces of plastered or unplastered new surfaces of ceiling applying three coats of white wash incl Preparation of surface complete all as specified and as directed by Engineer in Charge.

Taking down chowkaths or frames not exc 1.5 sqm (without takingoff shutter from the frame) each and removing from the site including dismantling brick work for hold fasts etc complete all as specified and as directed by Engineer in Charge.

S&F solid PVC moulded double door frames of size 50mm x 95 mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube, supply & fixing in opening as per specification & drawing complete all as specified and as directed by Engineer in Charge.

S&F for Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification colour WOOD COLOUR complete all as specified and as directed by Engineer in Charge.

Supply & fixing of stainless steel butt hinges 100 mm long medium weight complete all as specified and as directed by Engineer in Charge.

Supply & fixing aluminium anodised extruded fabricated type handle 150mm long complete all as specified and as directed by Engineer in Charge.

S&F 200 mm long Aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed by Engineer in Charge.

Taking down chowkaths or frames Exc 1.5 sqm but n.exc 4 sqm (without taking off shutter from the frame) each and removing from the site including dismantling brick work for hold fasts etc complete all as specified and as directed by Engineer in Charge.

Taking down Shutters exc 1 sqm but n exc 2 sqm each and refixing in the same opening complete all as specified and as directed by Engineer in Charge.

S& F Pressed steel frames of size 125 x 60 mm for doors with one or more rebates including supply & fixing lugs, 125 mm size hinges, lock strike plate, etc., complete all as specified and as directed by Engineer in Charge.

S& F Pressed steel frames of size 105 x 60 mm for doors with one or more rebates including supply & fixing lugs,125 mm size MS hinges, lock strike plate, etc., complete all as specified and as directed by Engineer in Charge.

Material and labour PCC 1:3:6 type C-1 (20 mm graded mechanically crushed stone aggregate) as in filling pressed steel frame /hold fast blocks etc complete all as specified and as directed by Engineer in Charge.

S&F factory made 35 mm thick Panelled shutters(any no of panels) with panel of timber flat on both side or veneered particle board medium density , wood particle board with commercial face veneers lipping frame to match complete all as specified and directed by Engr-in-Charge including supply and fixing following items : (a) Mild Steel Finished Butt Hinges 150mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm - 1 No per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 No per leaf

S&F 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-1 section 8 clause 8.20(a), kiln seasoned and chemically pressure treated all as specified including stainless steel 304 Grade wire cloth (wire dia. 0.36mm) complete all as specified and directed by Engr-in-Charge and the supply and fixing following items: (a) Mild Steel Finished Butt Hinges 150mm - 3 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x300mm - 1 No per leaf

Preparation of New wooden surfaces any width or girth not otherwise described and applying two coats synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer in Charge.

M&L Preparation of old wooden surface and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer in Charge.

S&F 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engr-in-Charge.

S&F in repair Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engr-in-Charge.

M&L for repair to RCC ceiling, sunshades, Chajjas, Balconies, Columns, bands, beams, roof slab and similar RCC work at any position/height by dismantling loose/disintegrated portion and dubbing out with Cement Concrete 1:1½:3, 15mm to 50mm thick using 6 to 12mm graded stone aggregate to make up and finished to required shape including provision of necessary supports if required and stitching of cracks with mild steel U clamps made out of 8mm dia @ 150mm c/c with inserting concrete block stretcher with cement mortar 1:3 mixed with adhesive chemical (Polymer based) and reinforced with PVC chicken mesh including form work where ever required and finished with10 mm thick plastering in CM 1:4 finished even and fair without using extra cement including preparation of surfaces to receive finishes complete all as specified and directed by Engr-in-Charge. Note : The extra area of 300mm around the actual affected area will be checked and repaired and only repaired portion will be taken for measurement.

Demolition of cement conceret un-reinforcement in ground floor and paving n,exc 15 cm thickness and dispose with in the MD land 1.5 km complete all as specified and directed by Engr-in-Charge.

M&L for 50 mm thick cement concrete type B-2, 1:2:4 (20 mm graded aggregate) as in floor topping of hard standing/ floor finished even and smooth without using extra cement (PCC shall be laid in alternate bays in panels of size complete all as specified and directed by Engr-in-Charge.

M&L for Plastic dividing strips 38 mm width, 1.5 mm thick complete all as specified and directed by Engr-in-Charge.

M & L for PCC with type D-2 1:4:8 (40 mm graded aggregate ) as in sub base, complete all as specified and directed by Engr-in-Charge.

Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection, 50 mm thick, surfaces finished even and smooth without using extra cement as in plinth protection including provision of construction joints, filled with polyurethane elastic adhesive/sealant (white/grey colour-sikaflex) of approx density 1.30kg/litre and form work complete all as specified and directed by Engr-in-Charge.

M&L coloured chequered cement concrete tiles 25 cm x25cmx25 mm thick , set , jointed and pointed in neat cement slurry in floors with grey cement and pigment incl 15 mm thick screed bed in cement mortar (1:6) complete all as specified and directed by Engr-in-Charge.

M&L for machine pressed precast concrete interlocking paver block any shape and size conforming to IS-15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment complete all as specified and directed by Engr-in-Charge.

Refixing of old machine pressed precast concrete interlocking paver block any shape and size of 60 mm thickness M-35 grade with grey cement and pigment complete all as specified and directed by Engr-in-Charge.

M&L for Factory made rubber moulded pre-cast cement concrete type B1 1 : 2: 4 (20mm graded aggregate) in kerb stone with plain fair faces, including chamfers, weathering throating etc and setting in cement mortar 1:6 complete with joints to match including necessary excavation embedding in the ground to depth indicated and tamping ground around and also for removing any surplus spoil to a distance n exc 50 mtrs complete all as specified and directed by Engr-in-Charge.

M&L for sand cushioning 25 mm thick for interlocxking tiles complete all as specified and directed by Engr-in-Charge.

Dismantling of brick work including all quoins arches pillars etc built in cement mortar complete all as specified and directed by Engr-in-Charge.

M&L brick work with subclass B bricks, straight or curved on plan exc 6m mean radious built in CM 1:6 complete all as specified and directed by Engr-in-Charge.

All as per above item no 1.045 but using old bricks obtained from , complete all as specified and directed by Engr-in-Charge.

M&L for Dismantling terrazzo/ glazed tiles as in floor/ skirting/ dado including cement mortar bedding (but not backing ) complete all as specified and directed by Engr-in-Charge.

S&F Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) (coloured tiles) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles 15mm thick screed bed or bedding layer CM 1:4 for laying finishes,complete all as specified as directed by Engr-in- Charge

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate 25mm thick as in bedding layer under floor tiles etc complete all as specified and directed by Engr-in-Charge.

S&F Glazed ceramic tiles (coloured tiles) in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 15 mm thick rendering in CM 1:4 on other than fair face of tiles complete all as specified and directed by Engr-in-Charge.

M&L welding in repairs gate, windows n exc 2.5 cm in length on steel surfaces of n.exc 6mm thickness of metal complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Rotational moulded polythylene 500 capacity water storage tank (Cylindrical vertical with closed top) Three Layer hoisted and fixed in position including PVC float valve 20 mm bore, high pressure with polythene ball & float & dismantling of old water tank complete all as specified and directed by Engr-in-Charge.

S&F in repairs Rotational moulded polythylene 1000 capacity water storage tank(Cylindrical vertical with closed top) Three layer hoisted and fixed in position including PVC float valve 20 mm bore, high pressure with polythene ball & float & dismantling of old water tank complete all as specified and directed by Engr-in-Charge.

S&F in repairs Rotational moulded polythylene 2000 capacity water storage tank(Cylindrical vertical with closed top) Three layer hoisted and fixed in position including PVC float valve 20 mm bore, high pressure with polythene ball & float & dismantling of old water tank complete all as specified and directed by Engr-in-Charge.

S&F in repair 15mm bib taps, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer in Charge.

S&F in repairs 15 mm bore Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer in Charge.

S&F in repairs 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls including fixing clamps with nut and bolts including taking down existing pipe complete all as specified and directed by Engineer in Charge.

S&F in repairs 110mm bore PVC(SWR) bends/shoe any radius fixed to walls including distance pieces and stack clamps complete all as specified by Engineer in Charge.

S&F in repairs Wash hand basin flat back 550x400mm vitreous china (white) with cantilever CI/Angle iron brackets embedded in concrete block including Brass chromium plated waste coupling 32mm bore, Waste pipe PVC 32mm bore, complete all as specified by Engineer in Charge

S&F in repairs waste fittings 32 mm brass chromium plated for glazed ware sinks, basins etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer in Charge.

S&F in repairs Flushing cistern of PVC 10 ltr. cap. with dual flushing system, valveless syphonic action type, , low level, white/ivory/off white with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete all as specified and directed by Engineer in Charge.

S&F in repair 15mm angle cock/ stop cock with flange cast copper alloy, chorminium plated, fancy type, screwed both ends for iron pipe or for union complete all as specified and directed by Engineer in Charge.

S&F in repair Vitreous china squatting pan, 'Orissa' pattern, size 580x440 mm white, with integral foot rests, CI 'P' or 'S' traps 100mm & PVC flush pipes 32mm dia including connecting to trap and to flushing pipe, anti-syphonage pipe etc including all joints and making good to floor complete all as specified and directed by Engineer in Charge.

S&F in repair Vitreous china wash down water closet pan (pedestal pattern), white excluding fixing bolts, flushing cistern and flush pipe complete all as specified and directed by Engineer in Charge.

S&F in repair figured glass 3mm thick pin head type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed by Engineer in Charge.

Preparation of New steel surfaces any width or girth not otherwise described and applying two coats synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer in Charge.

Material and labour for preparation of old steel surfaces of any description not otherwise described over 10cm width or grith and applying one coats of synthetic enamel paint over complete all as specified and directed by Engineer in Charge.

Taking down Aluminium window/ventilator shutter not exc 1 Sqm each including all accessories complete all as specified and directed by Engineer in Charge.

S&F Powder coated Anodised aluminium frame for doors, windows, ventilators, partations with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer in Charge.

S&F Powder coated Anodised aluminium side hung /sliding type window and ventilator shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, locks, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed by Engineer in Charge.

S&F Powder coated aluminium decorative grill of size of mesh 50mmX50mm fixed with doors, window for safety of glass etc. complete all as specified and directed by Engineer in Charge.

S & F sheet glass 5.5 mm thick ordinary quality and glazing with oil putty/ any type of beading in square/rectangular exceeding 1.00 Sqm in each pane, complete all as specified and directed by Engineer in Charge.

Supply & fixing Mild Steel Framed work such as Guard Bar/grill welded to window frame, angle iron or fixed independantlys, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 including dismantling existing Framed work complete all as specified and directed by Engineer in Charge.

Factory made steel windows or ventilators, fixed type with glazing bars complete all as specified and directed by Engineer in Charge.

Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site complete all as specified and directed by Engineer in Charge.

Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site complete all as specified and directed by Engineer in Charge.

S&F 15mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified and directed by Engr-in-Charge.

S&F 20mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC connections 15mm size with brass nuts of length 450mm complete all as specified and directed by Engr-in-Charge.

S&F in repair stainless steel grating 150 mm dia size shaped with cockroach trap for floor trap fixed in position complete all as specified and directed by Engr-in-Charge.

Demolition stone slab of any description or thickness, laid, bedded and pointed in any mortar complete all as specified and directed by Engineer in Charge.

M&L for 20-25 mm thick kota stone floor tiles machine cut (square/recatangular) etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 15mm thick screed bed n CM (1:6) as in screed bed or bedding and demolition of existing floor finishes complete as all specified and directed by Engr-in-Charge.

M&l for kota stone floor tiles 20-25 mm thick, machine cut (square/recatangular) as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 10 mm thick cement plaster in CM (1:4)for receiving tile to wall complete as all specified and directed by Engr-in-Charge.

Dismantling of brick or terracing tiles of single layers on roofs incl cleaning of bricks/tiles and removal of unusable bricks/tiles and removal from site, complete all as specified and directed by Engineer in Charge.

M&L for Wire brushing and cleaning the roof surfaces with water including flashings and junction of parapets, complete all as specified and directed by Engineer in Charge.

Demolition of mud in roof any thickness whether full thickness removed or part thereof including plaster & leaping complete all as specified and directed by Engineer in Charge.

M&L for APP polymeric water proofing membrane minimum 3 mm thick and weighting not less than 3.6 Kg/Sqm black finish reinforced with non-woven polyster matt wt not less than 150 gms/Sqm with thermo fusable finish laid over compatible bitumen primer at the rate of 0.40 Ltr/Sqm torching over laps with a propane or abutan gas torch with a over lap of 75 mm at the side and 100 mm at the ends and sealing including applying a coat of cold emulsion bituminious primer all as per manufacturers instructions incl preparation of surface, complete all as specified and directed by Engineer in Charge.

Plain cement concrete (1:2:4) type B-1, using 12.5 mm graded mechanically crushed stone aggregates as in padding to roof to maintain the required slope and finished the surface even and smooth without using extra cement, complete all as specified and directed by Engineer in Charge.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed by Engineer in Charge.

M&L for Writing letters or figures (Block.Roman, Italic or Indian) n exc. 30 cm high shall be painted with thick paint, so that they stand out boldly and solidly without showing signs of brush marks complete all as specified and as directed by Engr-in-Charge

M&L for removing bushes upto 10cm dia trunk, grass from roof top and racking out jouints/pointing to brick tiles and flush pointing with CM 1:3 all as specified and directed by Engr-in-Charge.

Dismantling of asbetos/fibre cement corrugated/semi corrugated sheet in roof covering including ‘J’ or ‘L’hooks complete all as specified and directed by Engineer in Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self tapping screws as recommended by manufacturer complete all as specified and directed by Engineer in Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer in Charge.

Dismantling of post or struts (wood or steel or RCC) any section incl taking embeded portion and making good disturbed ground embeded in concrete complete all as specified and directed by Engineer in Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and directed by Engineer in Charge.

M&L for PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in fixing RCC/ any fencing posts and similar items, complete all as specified and directed by Engineer in Charge.

S&F MS angle as in iron posts and struts, gates, flat & round bars in fencing including cutting tops to shape as directed, drilling holes, notching for wire, bolting etc and similar works like MS flat iron fillets confirming to Fe-290 Gde E-165 complete all as specified and directed by Engineer in Charge.

S&F round bars 10 mm dia and over, cut to length, bent to shape as required incl cracking bending hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia, complete all as specified and directed by Engineer in Charge.

Dismantling fencing barbed wire /mesh complete all as specified and directed by Engineer in Charge.

S&F Galvanized 2 strand steel barbed wire 2.24 mm dia barbed wire with 2 mm dia barbs at 75 mm spacing straining, tightening and fixing to MS nibs embeded in pre cast RCC fencing post struds etc securing and typing as crossing with and provision of galvanized mild steel wire complete all as specified and directed by Engineer in Charge.

Fixing only in Galvanized 2 strand steel barbed wire 2.24 mm dia barbed wire with 2 mm dia barbs at 75 mm spacing straining, tightening and fixing to MS nibs embeded in pre cast RCC fencing post struds etc securing and typing as crossing with and provision of galvanized mild steel wire complete all as specified and directed by Engineer in Charge.

S&F mild steel screw bolt 11 to 15 mm dia (machine made) with hexagonal head at one end and screwed the other, screwed end to be fitted with one washer and hexagonal nut length exc 10cm but not exc 15cm long complete all as specified and directed by Engineer in Charge.

Dismantling fencing wire mesh, any type complete all as specified and directed by Engineer in Charge.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed by Engineer in Charge.

Supply only Chain link MS galvanisd fencing, any size or type, complete all as specified and directed by Engineer in Charge.

S&F in repair 3 mm dia PVC Coated galvanised mild steel chain link fencing of mesh size 50x50 mm fixed with straining bolts including line wire any mesh size and type to any type of standards , rails,straining bolts etc including provision of binding wire , complete all as specified and directed by Engineer in Charge.

Repairs to gates of any description and size including taking down and repairs to pintle hinges welding if required and bedding in brick or concrete work and check for its movement align the shutter by means of hammering / welding/oiling, lifting the shutter by means of pully or crane by taking safety measuers including replacement of pintle hinges, complete all as specified and directed by Engineer in Charge.

S&F Roof trusses (framed),Fe 410-W (Gde E-250) quality A trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. including dismantling of existing Roof Truss complete all as specified and directed by Engineer in Charge.

S&F in Repair steel roling shutters ,without ball bearing 1.00 mm thickness as specified incl top cover , anchoring rod, hasp and staple and one shop coat of primer complete push pull or manual type incl taking down of old shutter of any thickness complete all as specified and directed by Engineer in Charge.

S&F in Repair for precast cement concrete type B-0 1:2:4 using 12.5mm gr aggr set in CM 1:4 louvers and jallies 25mm thk (measured solid) incl all mouldings complete all as specified and directed by Engineer in Charge.

E/M WORKS

Taking down Care fully Copper/Aluminium Point Wiring any type in PVC casing caping /PVC Conduit (Light, Fan, Socket or Power) including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets, Light Fittings of any description and Making Good Disturbed Surfaces of Walls, Floors, etc. so as to match with the Existing Finishes, complete all as specified and as directed by Engineer in Charge.

Taking down/out unserviceable main switches and DB's including MCBs of any size / type and of any description and Making Good Disturbed Surfaces of Walls, Floors, etc. so as to match with the Existing Finishes, complete all as specified and as directed.

M&L for concealed Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn through and including Rigid Non-metallic PVC Conduit 19mm in size, medium grade, ISI marked and its Accessories in Concealed (Partly)/ Surface (Partly) with necessary grouting of required size and depth on Wall and Making Good in Cement Mortar 1:3, providing PVC Gang Box (minimum 2.0mm thick)/Sunk Mild Steel Pressed Terminal Box (1.6mm thick) of suitable size duly painted with Red Oxide Metal Primer with 3.0mm thick Plastic Laminated Sheet Top Cover (as per Site requirement) for mounting Switches, Sockets, Fan Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/FAN POINT/ BELL POINT CONTROLLED BY ONE 1-WAY SWITCH 6 AMP, complete all as specified and as directed.

All as per Item No 2.03 for One 3 Pin Switch socket Combination 6 amp on the independent board.

All as per Item No 2.03 for One 3 Pin swich socket Combination 6 amp on the same board with other switches.

M&L for concealed Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Cable, drawn through and including Rigid Non-metallic PVC Conduit 19mm in size, medium grade, ISI marked and its Accessories with necessary grouting of required size and depth on Wall and Making Good in Cement Mortar 1:3, providing PVC Gang Box (minimum 2.0mm thick)/Sunk Mild Steel Pressed Terminal Box (1.6mm thick) of suitable size duly painted with Red Oxide Metal Primer with 3.0mm thick Plastic Laminated Sheet Top Cover (as per Site requirement) for mounting Switches, Sockets, Fan Regulators, etc. Earth Continuity Cable connected to Common Earth dolly for ONE 6 PIN SOCKET 16 AMP ON INDEPENDENT BOARD, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Flush type, Single Pole, 1-way and , complete all as specified and as directed.

S&F Switch Piano 16 Amp, Flush type, Single Pole, 1-way, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, Piano, Flush type, 2-in-1, multi-purpose, 5 Pin, complete all as specified and as directed by Engineer in Charge.

S&F Socket Outlet 6 Amp & 16 Amp, Piano, Flush type, 2-in-1, multi-purpose, 6 Pin, complete all as specified and as directed by Engineer in Charge.

S&F Fan Regulator in 5 Step type, Single Pole, 230 Volt, Electronic type, complete all as specified and as directed by Engineer in Charge.

S&F Ceiling Rose, 3 Terminals, PVC Polycarbonate, Isolated body and complete all as specified and as directed.

Taking down/out unserviceable Wires only from the existing Sub-main Wiring of any type and any description, without disturbing Existing Conduit, complete all as specified and as directed.

S&F Sub-main Wiring with 2-Runs of 4.0 Sqmm (nominal area) 1100 Volt, PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable and 1-Run of 4.0 Sqmm (nominal area) 1100 Volt, PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuty Cable along with the Wiring drawn in PVC Conduit medium grade 25mm dia including making Good Disturbed Surfaces of Walls, Floors, etc. so as to match with the Existing Finishes, complete all as specified and as directed by Engineer in Charge. Note: (a) The quoted unit rate shall include cost of PVC Conduit (b) Two Runs of Copper cable along with One Runs for earthing and one Run of PVC Conduit shall be measured as one unit.

S&F MCB DB 8-way, Single Pole & Neutral, Factory made TP-43 Protection class metal Double Door type, Regal Grey Colour, Sheet Steel Phosphatised, Powder Coated with 200 Amp rate Bus-bar, Neutral Link Earth Bar & Din Rail duly embedded/Concealed upto Wall surfaces including Connecting up with Existing Cable Incoming and Outgoing with Cable Lugs as per the Site requirement and and Making Good Disturbed Surfaces of Walls/Roofs/Floors, etc. so as to Match with the Existing Finishes, complete all as specified and as directed.

S&F MCB DB 4-way, Single Pole & Neutral, Factory made TP-43 Protection class metal Double Door type, Regal Grey Colour, Sheet Steel Phosphatised, Powder Coated with 200 Amp rate Bus-bar, Neutral Link Earth Bar & Din Rail duly embedded/Concealed upto Wall surfaces including Connecting up with Existing Cable Incoming and Outgoing with Cable Lugs as per the Site requirement and and Making Good Disturbed Surfaces of Walls/Roofs/Floors, etc. so as to Match with the Existing Finishes, complete all as specified and as directed.

S&F MCB Single Pole 40 Amp, 240 /415 Volt, AC, 'B' Series for fixing on MCB DB’s, 10 kA, 50 Hz , 35mm2 Terminal Capacity insulated sliding shutter including Connecting up and Fixing in DB of any make/ type, complete all as specified and as directed.

S&F MCB Single Pole & Neutral, 40 to 63 Amp, 240 /415 Volt, AC, 'C' Series for fixing on MCB DB’s, 10 kA, 50 Hz , 35mm2 Terminal Capacity insulated sliding shutter including Connecting up and Fixing in DB of any make/ type, complete all as specified and as directed.

S&F 1X18 watt incl taking down wall mounted, new generation LED T-8 Retro fit for multipurpose application with LED Rod, made from exturded aluminium housing, polycarbonate diffuser including all fixing accessories & connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed by Engr-in-Charge.

GUPTA AND ENGINEERS

M/s Kamal Builders

SWARN SINGH AND CO.

Rasvinderpalandco

STELLAR PROJECTS

PREM ENTERPRISES

M/s BALDEV SINGH