Construction of External Infrastructure Electrical Works Ph II and III Local Control Substation 3 and 4 Firefighting Works and miscellaneous Electrical Works at the Permanent Campus of IIM Shillong Umsawli Meghalaya

Amount

Total Amount of BoQ 2

Amount after unconditional Rebate

Description of Work / Item(s)

Amount

Total of BoQ 3 to BoQ 6

Total Amount of BoQ3 (Item Rate)

Total Amount of BoQ4 (Percentage Rate)

Total Amount of BoQ5 (Percentage Rate)

Total Amount of BoQ6 (Percentage Rate)

Description of Work / Item(s)

Amount

Schedule - (D) Bill of Quantites for Non Schedule Items (Electrical Works )

HT Panels (Modification work inside existing Phase-I 11KV panel of MRS )

NS-1: Modification work inside existing Phase-I 11KV panel of MRS

A. All incomer CTs of 11KV SWGR will be replaced by 400/5 A as per total load of entire complex (Phase-I, II & III) and Ammeter also will be replaced by 0-400A range. B. The CT of Outgoing feeder-4 & 5 of 11KV SWGR will be replaced by 250/5A as per total load of Phase-II & III and Ammeter also will be replaced by 0-250A range. Ref. Drawing No. 47306700/MRS/EL/SLD/T/002 C. One additional 11KV VCB will be added as a Spare feeder for Phase- I, II & III.

NS-1.1: CURRENT TRANSFORMER

NS-1.1.1: 1 Set - Dual core CTs 400/5/5 A of 15 VA burden and accuracy Class - 1 for metering and class 5P10 for protection.

NS-1.1.2: 2 Set - Dual core CTs 250/5/5 A of 15 VA burden and accuracy Class - 1 for metering and class 5P10 for protection.

NS-2: Digital Ammeter

NS-2.1: 2Set - 0 - 250A Digital Ammeter

NS-2.2: 1Set - 0 -400 A Digital Ammeter

NS-3: Supplying, installation, testing & commissioning of indoor type floor mounted metal clad, totally enclosed, 1 No. Panels 11 KV VCB board with single break, trip free, motorised spring charged with electrical closing arrangement with horizontal drawout and vertical/horizontal isolation type breaker with mechanical ON/OFF indicator and trip device, 4 NO + 4 NC auxilliary contact complete with self contained, fully interlocked, rack in and rack out mechanism as per IS 13118, as amended up to date and additional specifications, with air insulated encapsulated copper bus bars of 630Amps capacity suitable for use on 11 KV, 3 Phase, 50Hz AC supply and short circuit with stand capacity of 350 MVA ( 18.4 KA) for one seconds, and bottom entry gland plate suitable for 1x3C x 185sqmm 11 KV XLPE cable as required .

11KV VCB Panel ( 1 Adapter Panel + 1 no. Outgoing Panels as a ADD ON PANELSpare (Each Comprising of)

1 No. - 11 KV, 630 Amp VCB with Shunt trip Coil suitable for operation on 24 Volt DC.

1 Set - Dual core CTs 250/5/5 A of 15 VA burden and accuracy Class - 1 for metering and class 5P10 for protection.

1 No - Microprocessor based IDMT relay with 3 O/L, 1 E/F element and Instantaneous relay with 3 O/L element with modbus communication.

1 No - Master trip relay

1 No - Trip Circuit Supervision relay.

1 Set - Trip/Neutral/Close Switch

1 Set - ON,OFF,Trip, Spring Charged,Trip circuit Healthy , DC Fail indication LED lamp.

1 Set - Trip circuit healthy test push button with indication lamp.

Gland plate suitable for 1x 3C x185 sqmm 11 KV grade XLPE cable.

1 No - 6 Way Window Annunciation Facia

Control Supply Voltage :

Motor operation, Heater, Panel Illumination Light : 240V AC

Shunt Trip, Closing, Indication & Annunciation : 24V DC

HT Panels

NS-4: 11 KV Panel (LCS-3)

Supplying, installation, testing & commissioning of indoor type floor mounted metal clad, totally enclosed, 8 Panels 11 KV VCB board (2-Incomingr and 5-nos outgoing) with single break, trip free, motorised spring charged with electrical closing arrangement with horizontal drawout and vertical/horizontal isolation type breaker with mechanical ON/OFF indicator and trip device, 4 NO + 4 NC auxilliary contact complete with self contained, fully interlocked, rack in and rack out mechanism as per IS 13118, as amended up to date and additional specifications, with air insulated encapsulated copper bus bars of 630 Amps capacity suitable for use on 11 KV, 3 Phase, 50Hz AC supply and short circuit with stand capacity of 350 MVA for three seconds, and bottom entry gland plate suitable for 1x3C x 300 or 240sqmm 11 KV XLPE cable as required .

Incoming - 2no. ( Each Comprising of )

1 No - 11 KV, 630 Amp VCB with 11KV/110V PT of 100 VA burden and Accuracy Class 1, Shunt trip Coil suitable for operation on 24 V DC & Castel Key Interlock.

1 Set - Dual core CTs 250-100/5/5A of 15VA burden and accuracy Class - 1 for metering and class 5P10 for protection.

1 No - Digital multi function meter suitable for reading Voltage, Current, Power factor, HZ, , KW, KWH, MD, KVA/KVAR with modbus communication

1 No - Microprocessor based IDMT relay with 3 O/L, 1 E/F element and Instantaneous relay with 3 O/L element with modbus communication.

1 No - Master trip relay

1 No - Trip Circuit Supervision relay.

1 Set - Trip/Neutral/close switch

1 Set - ON,OFF,Trip, Spring Charged,Trip circuit Healthy , DC Fail indication LED lamp

1 Set - R,Y,B Phase indication LED lamp

1 Set - Trip circuit healthy test push button and indication lamp.

Gland plate suitable for 1x3C X 240 sqmm 11 KV grade XLPE cable.

1 No - 6 Window Annunciation Facia

Outgoing - 5Nos (3nos Working + 2nos Spare) (Each Comprising of)

1 No. - 11 KV, 630 Amp VCB with Shunt trip Coil suitable for operation on 24 Volt DC.

1 Set - Dual core CTs 200-100/5/5 A of 15 VA burden and accuracy Class - 1 for metering and class 5P10 for protection.

1 No - Microprocessor based IDMT relay with 3 O/L, 1 E/F element and Instantaneous relay with 3 O/L element with modbus communication.

1 No - Master trip relay

1 No - Trip Circuit Supervision relay.

1 Set - Trip/Neutral/Close Switch

1 Set - ON,OFF,Trip, Spring Charged,Trip circuit Healthy , DC Fail indication LED lamp.

1 Set - Trip circuit healthy test push button with indication lamp.

Gland plate suitable for 1x 3C x240 sqmm 11 KV grade XLPE cable.

1 No - 6 Way Window Annunciation Facia

Control Supply Voltage :

Motor operation, Heater, Panel Illumination Light : 240V AC

Shunt Trip, Closing, Indication & Annunciation : 24V DC

NS-5: 11 KV Panel (LCS-4)

Supplying, installation, testing & commissioning of indoor type floor mounted metal clad, totally enclosed, 5 Panels 11 KV VCB board (2-Incomingr and 3-nos outgoing) with single break, trip free, motorised spring charged with electrical closing arrangement with horizontal drawout and vertical/horizontal isolation type breaker with mechanical ON/OFF indicator and trip device, 4 NO + 4 NC auxilliary contact complete with self contained, fully interlocked, rack in and rack out mechanism as per IS 13118, as amended up to date and additional specifications, with air insulated encapsulated copper bus bars of 630 Amps capacity suitable for use on 11 KV, 3 Phase, 50Hz AC supply and short circuit with stand capacity of 350 MVA for three seconds, and bottom entry gland plate suitable for 1x3C x 240sqmm 11 KV XLPE cable as required .

Incoming - 2no. ( Each Comprising of )

1 No - 11 KV, 630 Amp VCB with 11KV/110V PT of 100 VA burden and Accuracy Class 1, Shunt trip Coil suitable for operation on 24 V DC & Castel Key Interlock.

1 Set - Dual core CTs 200-100/5/5A of 15VA burden and accuracy Class - 1 for metering and class 5P10 for protection.

1 No - Digital multi function meter suitable for reading Voltage, Current, Power factor, HZ, , KW, KWH, MD, KVA/KVAR with modbus communication

1 No - Microprocessor based IDMT relay with 3 O/L, 1 E/F element and Instantaneous relay with 3 O/L element with modbus communication.

1 No - Master trip relay

1 No - Trip Circuit Supervision relay.

1 Set - Trip/Neutral/close switch

1 Set - ON,OFF,Trip, Spring Charged,Trip circuit Healthy , DC Fail indication LED lamp

1 Set - R,Y,B Phase indication LED lamp

1 Set - Trip circuit healthy test push button and indication lamp.

Gland plate suitable for 1x3C X 240 sqmm 11 KV grade XLPE cable.

1 No - 6 Window Annunciation Facia

Outgoing - 3Nos (1no Working + 2nos Spare) (Each Comprising of)

1 No. - 11 KV, 630 Amp VCB with Shunt trip Coil suitable for operation on 24 Volt DC.

1 Set - Dual core CTs 150-100/5/5 A of 15 VA burden and accuracy Class - 1 for metering and class 5P10 for protection.

1 No - Microprocessor based IDMT relay with 3 O/L, 1 E/F element and Instantaneous relay with 3 O/L element with modbus communication.

1 No - Master trip relay

1 No - Trip Circuit Supervision relay.

1 Set - Trip/Neutral/Close Switch

1 Set - ON,OFF,Trip, Spring Charged,Trip circuit Healthy , DC Fail indication LED lamp.

1 Set - Trip circuit healthy test push button with indication lamp.

Gland plate suitable for 1x 3C x240 sqmm 11 KV grade XLPE cable.

1 No - 6 Way Window Annunciation Facia

Control Supply Voltage :

Motor operation, Heater, Panel Illumination Light : 240V AC

Shunt Trip, Closing, Indication & Annunciation : 24V DC

NS-6: 24 V, DC Battery Bank (100AH)-LCS 3&4

Supply, Installation, Testing and Commissioning of Lead Acid Battery Bank Type VRLA having 2 Volt cell (12 Nos.) along with connector, link, insulator and Steel/Wooden Battery shelve. The following accessories are to be supplied with the Battery Bank.

NS-7: 24V, DC Battery Charger and DCDB-LCS 3&4

Supply, Installation, Testing and Commissioning of 24V DC Battery charger for the above 24V DC VRLA type battery bank, Transformer for Boost and trickle charging system with indicating, metering and necessary protective instrument/relays as per technical specification.

a) 1 no. Ampere - Hour meter has to be included.

b) Battery charger should have a DC Distribution Board as an integral/separate DB consisting of the following equipments.

c) 1 no - 100A rated DC MCCB as incomer

d) 8 nos - 16A DP MCB (DC) as outgoing feeder.

e) 1 Set - 125A rated DC Busbar (Copper)

Transformers

NS-8: Transformer FOR LCS-3

Supplying, installation, testing and commissioning of Cast Rasin Dry Type 1000KVA 11/0.433 KV, 3 Phase, 50Hz, Dyn11 vector group,copper wound, class F insulation associated with winding temperature dicator/controller actuated by means of resistance temperature detector embedded in LV windings, indoor type Transformer with approximately 5% impedance, tapping for off load operation on HV side in steps of +5% to -5% @ ±2.5% having cable end boxes on HV sides suitable for 1x3Cx 240Sqmm XLPE cable of 11KV grade and 1600A Al BusDuct of 1.1 KV grade on LV sidewith neutral brought out separately i/c supplying and laying of copper conductor multicore control cable from transformer to HT breaker for safety tripping, suitable mounted on M.S. channel i/c supplying grounding of suitable M.S. Channel with all accessories and confirming to IS 11171:1985 & as per specification attached complete in all respects as required at site ( (to be installed indoor).

NS-9: Transformer FOR LCS-4

Supplying, installation, testing and commissioning of Cast Rasin Dry Type 1600KVA 11/0.433 KV, 3 Phase, 50Hz, Dyn11 vector group,copper wound, class F insulation associated with winding temperature dicator/controller actuated by means of resistance temperature detector embedded in LV windings, indoor type Transformer with approximately 6.25% impedance, tapping for off load operation on HV side in steps of +5% to -5% @ ±2.5% having cable end boxes on HV sides suitable for 1x3Cx 240Sqmm XLPE cable of 11KV grade and 2500A Al BusDuct of 1.1 KV grade on LV side with neutral brought out separately i/c supplying and laying of copper conductor multicore control cable from transformer to HT breaker for safety tripping, suitable mounted on M.S. channel i/c supplying grounding of suitable M.S. Channel with all accessories and confirming to IS 11171:1985 & as per specification attached complete in all respects as required at site (to be installed indoor).

DG WORK FOR-LCS 3&4

NS-10: Supplying, Installation, testing and commissioning of Silent type DG set having Prime Power Rating of 320KVA, 415 volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 HZ, 3 phase system & for 0.8 Load Factor and consisting of the Followings:

Diesel Engine:

Diesel Engine 4 stroke Radiator cooled, electric start, of suitable BHP at 1500 RPM suitable for above output of alternator at 40 Degree C, 50% RH and at 1500 Meter MSL and conforming to BS 5515, BS 649, IS 10000, capable of taking 10% overloading for one hour after 12 hours of continuous operation. The engine will be fitted complete with all the required accessories.Engine should be designed at 40 Deg C and it should not derate at site condition of 1500 Mtrs & 30 Deg C

Engine mounted instrument Panel fitted with and having digital display for following:

(i) Start-Stop switch with key

(ii) Radiator temperature Indication

(iii) Lubrication oil pressure indication

(iv) Lubrication oil temperature indication

(v) Battery Charging indication

(vi) RPM indication

(vii) Over Speed trip indication

(viii) Low Lub. Oil pressure trip indication

(ix) Engine hours indication

Alternator:

Synchronous alternator rated at 320 KVA, 415 volts at 1500 RPM, 3 Phase, 50HZ, AC supply with 0.8 lagging power factor at 40 Degree C, 50% RH & at 1500 Meter MSL. The alternator shall be having SPDP enclosure, brushless, continuous duty, self-excited and self-regulated through AVR conforming to IS:4722/BS 2613 suitable for tropical conditions and with class H insulation.

Base Frame & Foundation

Both the engine and alternator shall be mounted on suitable base frame made of MS channel with neccesary with reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendations of manufacturer.

Fuel Tank:

Daily service fuel tank of 900 Ltrs. Capacity fabricated out of 3 mm thick M.S. sheet complete with standard accessories and fuel piping between fuel tank and diesel engine with MS Class 'C' pipes of suitable dia. Complete with valves, level indications and accesories (allowed to provide externally) as required as per specifications.

Exhaust System:

Dry Exhaust mainfold with residential exhaust silencer and without cataytic convertor.

Starting System:

DC starting system comprising of starter motors: voltage regulator and arrangement for initial excitation complete with suitable nos. of batteries as required as per OEM/OEA.

Diesel Engine generating set shall be treated with Accoustic enclosure manufactured by OEM/OEA and complying with CPCB norm, confirmnment to specifications.

NS-11: Supplying, Installation, testing and commissioning of Silent type DG set having Prime Power Rating of 900 or 910 KVA, 415 volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 HZ, 3 phase system & for 0.8 Load Factor and consisting of the Followings:

Diesel Engine:LCS-3

Diesel Engine 4 stroke Radiator cooled, electric start, of suitable BHP at 1500 RPM suitable for above output of alternator at 40 Degree C, 50% RH and at 1500 Meter MSL and conforming to BS 5515, BS 649, IS 10000, capable of taking 10% overloading for one hour after 12 hours of continuous operation. The engine will be fitted complete with all the required accessories.Engine should be designed at 40 Deg C and it should not derate at site condition of 1500 Mtrs & 30 Deg C

Engine mounted instrument Panel fitted with and having digital display for following:

(i) Start-Stop switch with key

(ii) Radiator temperature Indication

(iii) Lubrication oil pressure indication

(iv) Lubrication oil temperature indication

(v) Battery Charging indication

(vi) RPM indication

(vii) Over Speed trip indication

(viii) Low Lub. Oil pressure trip indication

(ix) Engine hours indication

Alternator:

Synchronous alternator rated at 900 or 910 KVA, 415 volts at 1500 RPM, 3 Phase, 50HZ, AC supply with 0.8 lagging power factor at 40 Degree C, 50% RH & at 1500 Meter MSL. The alternator shall be having SPDP enclosure, brushless, continuous duty, self-excited and self-regulated through AVR conforming to IS:4722/BS 2613 suitable for tropical conditions and with class H insulation.

Base Frame & Foundation

Both the engine and alternator shall be mounted on suitable base frame made of MS channel with neccesary with reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendations of manufacturer.

Fuel Tank:

Daily service fuel tank of 900 Ltrs. Capacity fabricated out of 3 mm thick M.S. sheet complete with standard accessories and fuel piping between fuel tank and diesel engine with MS Class 'C' pipes of suitable dia. Complete with valves, level indications and accesories (allowed to provide externally) as required as per specifications.

Exhaust System:

Dry Exhaust mainfold with residential exhaust silencer and without cataytic convertor.

Starting System:

DC starting system comprising of starter motors: voltage regulator and arrangement for initial excitation complete with suitable nos. of batteries as required as per OEM/OEA.

Diesel Engine generating set shall be treated with Accoustic enclosure manufactured by OEM/OEA and complying with CPCB norm, confirmnment to specifications.

NS-12: Auto Synchronization Panel

Supply, installation, testing and commissioning of auto main failure (AMF) / auto synchronizing / auto load sharing / auto load management based on demand feed back, Genset controller with load management PLC shall collect demand feed back from MFM in panels / transformer incomers & necessary wiring & communication from meter to PLC, auto change over, inter locking DG control and operation programmable logic controller (PLC) based logic panel cubicle type made of 2 mm thick CRCA sheet enclosure, powder coated, free standing, floor mounted, dust and vermin proof, indoor suitable for following DG sets complete with all measuring instruments, protective devices, alarm, etc. as required for above functions rated for 50KA RMS fault level withstand for 1 sec, PLC with required digital & analogue input & output modules, input/output racks, power supplies and communication with Power Monitor.

microprocessor based Genset Controller with communciation cables etc. as required and degree of protection IP:54 & all relays shall be microprocessor based comprising of the following:

DG Synchronization Panel for Substation

Panel Suitable for 2 Nos DG Set. ( 320KVA & 900 or 910 KVA)

Synchronizing Switch - 1 No.

2 Line Display Multifunction Meter - 1 No.

MANUAL/AUTO Switch - 1 No.

Test PB Yellow -Test Push Button with 1 NO Contact - 1 No.

Accept PB Blue -Test Push Button with 1 NO Contact - 1 No.

Reset PB Black -Test Push Button with 1 NO Contact - 1 No.

Engine Start PB Green - Test Push Button with 2 NO Contact - 1 No.

Engine Stop PB Red -Test Push Button with 1 NC Contact - 1 No.

CB Close PB Green - Test Push Button with 1 NO Contact - 1 No.

CB Trip PB Red - Test Push Button with 2 NO Contact - 1 No.

Emergency Stop PB Mushroom Red - 1 NO

Voltage Raise/Lower Joysticks - 1 NO -

Speed Raise/Lower Joysticks - 1 NO -

PLC HARDWARE (Synchronizing Equipment)

PLC-CPU -Battery free CPU with on board Profibus / Ethernet Port - 1 No.

On line 2 KVA UPS for PLC & CPU ( 30min Back up time.)

Minmum requirement of PC with Core 2 Duo processor, 250 GB HDD, 2 GB RAM, DVD Writer, Optical Mouse, Multimedia Key Board, 21" LED Monitor with Licensed Windows Operating System or latest latest updated available hardware and software at the time of purch

Suitable Digital Input Module - Minimum 16 CH .

Suitable Digital Output Module - Minimum 16 CH .

MMC (Micro memory card) 128KB/ as required - 1 No.

Analogue input / output module as per requirement.

Communication cable & accessories & Software for PLC programming with mimic diagram-1 Set

Licensed software for Runtime application -1 Set

Controller in DG Vender Scope

Engine Fault Relay

LLOP ON Delay,

Fuel Solenoid Relay,

Cranking Relay

Speed Lower Relay.

Speed Raise Relay .

Voltage Lower Relay .

Voltage Raise Relay .

Under Voltage Aux. Relay

Trip Command Relay

Close Command Relay

ACB Aux.Relay

Manual Relay

Auto Relay

DC Failure Relay

B/C+TR I/C Status Relays

Mains voltage monitor relay.

RELAYS W/O COMMUNICATION

Check Synchronizing Relay II OvAC,5OHz - 1 No.

PILOT LIGHTS /INDICATIONS -

Pilot Light Amber 230v AC(DC Failure) - LED type - 1 No.

Pilot Light Red 24v DC (DC ON ) - LED type - 1 No.

Pilot Light Red 24V AC (Set ON) - LED type - 3 No.

Annunciator 12 Channel for DG faults - 24V DC - 3 No.

Status Indicator 12 Channel - 24V DC - I No.

POWER SUPPLY

230V AC/ 24V DC ,Stabilized Power Supply with voltage trimmer - 1 Set.

Sealed Maintenance Free Battery - 12V, 40AH - 2 No.

MISCELLANEOUS COMPONENTS

Auxiliary/MCC Panel for DG set accessories

Control Cables between DG & DG Incomer panel

Exhaust Fan - 6" - 1 No.

Control MCB - I Set

Control Fuse - 1 Set

Panel Light - 11 W CFL - 2 No.

Door Switch - 6A - 2 No.

Space Heater - 150W - 1 No.

Switch Socket - 5A/15A,3 Pin - 1 No.

Solid State Alarm 24v DC - 1 No.

Terminals - 2.7 Sq. mm - 1 Set

PANEL+ HARDWARE

Earth Bus - Copper - 1 Set

Earth links for Door Earthing -

PVC Cu. 6 Sq. mm - 1 Set

Enclosure - 1 Set

Filters - 1 Set

Terminals Mounting Track - 1 Set

Terminals Anchor End - 1 Set

DG/Bus monitoring PT's - 1 Set

PLC Hardware System- SIEMENS / ALLEN BRADLEY

LT PANELS

NS-13: MAIN LT Panel -1 ( LCS-3)

Supplying installation testing and commissioning of extendable, compartmentalised, front operated, back openable, LT cubicle panel having ingress protection of IP 42, suitable for operation on 415 Volt 3 phase 50 HZ power supply fabricated out of 2 mm thick CRCA sheet steel and base channel of MS section not less than 100mm x 50mm x 5mm, gland plate of 3mm thick cleaned and treated in 7 tank process and power coated with approved shade with 2000 Amp TPN Aluminium busbar suitable to withstand 50KA fault level for 1Sec complete with supplying & installation of following equipment including inter connection, control wiring ets as required . Ref. Standard IEC 61439 .Note: All I/C & O/G ABC &MCCB (250 Amps and above 250Amps) are microprocessor based

Incoming -BR-1 (From Transformer)

1 No - 1600 Amp 415 V 4Pole EDO (Electriically operated Draw-out) type microprocessor controlled ACB with O/L, E/F,S/C release, shunt trip Coil suitable for operation on 24 Volt DC and Electrical interlock.

1 Set - single core CTs 1600/5 A of 15 VA burden and accuracy Class - 1 for metering.

1 Set - single core CTs 1600/5 A of 15 VA burden and accuracy Class - 1 for APFCR (only one Incommer of Transformer feeder)

1 No. reverse power relay

1 No - Digital Load Manager suitable for reading & display Voltage, Current, Power factor, KW, KWH

1 No - Line PT 415V/110V of 100 VA burden and accuracy Class - 1

1 No - Microprocessor based IDMT relay with 1 E/F element.(Stand by E/F) (only one Incommer of Transformer feeder)

1 Set - ON,OFF,Trip, Spring Charged,Trip circuit Healthy indication LED lamp

1 Set - Trip circuit healthy test push button with indication lamp.

1 Set - R,Y,B Phase indication LED lamp with 2 Amp back up HRC fuse.

Gland plate suitable for 1600A BusDuct of 1.1 KV grade ( Top Entry)

BUS COUPLER- BC-1 & BC-2

2 No - 1600 Amp 415 V 4Pole EDO (Electriically operated Draw-out) type microprocessor controlled ACB with O/L, E/F,S/C release, shunt trip Coil suitable for operation on 24 Volt DC and Electrical interlock.

Incoming - BR-2 (From DG-1)

1 No - 630Amp 415 V 4Pole EDO (Electriically operated Draw-out) type microprocessor controlled ACB with O/L, E/F,S/C release, shunt trip Coil suitable for operation on 24 Volt DC and Electrical interlock.

1 Set - single core CTs 630/5 A of 15 VA burden and accuracy Class - 1 for metering.

1 No. reverse power relay

1 No - Digital Load Manager suitable for reading & display Voltage, Current, Power factor, KW, KWH

1 No - Line PT 415V/110V of 100 VA burden and accuracy Class - 1

1 Set - ON,OFF,Trip, Spring Charged,Trip circuit Healthy indication LED lamp

1 Set - Trip circuit healthy test push button with indication lamp.

1 Set - R,Y,B Phase indication LED lamp with 2 Amp back up HRC fuse.

Gland plate suitable fo r2x300 Sq.mm Cable of 1.1 KV grade ( Bottom Entry)

Incoming -BR-3 (From DG-2)

1 No -1600Amp 415 V 4Pole EDO (Electriically operated Draw-out) type microprocessor controlled ACB with O/L, E/F,S/C release, shunt trip Coil suitable for operation on 24 Volt DC and Electrical interlock.

1 Set - single core CTs 1600/5 A of 15 VA burden and accuracy Class - 1 for metering.

1 No. reverse power relay

1 No - Digital Load Manager suitable for reading & display Voltage, Current, Power factor, KW, KWH

1 No - Line PT 415V/110V of 100 VA burden and accuracy Class - 1

1 Set - ON,OFF,Trip, Spring Charged,Trip circuit Healthy indication LED lamp

1 Set - Trip circuit healthy test push button with indication lamp.

1 Set - R,Y,B Phase indication LED lamp with 2 Amp back up HRC fuse.

Gland plate suitable for 6X300 Cable of 1.1 KV grade ( Bottom Entry)

Outgoings

All Outgoing MCCB (250 Amps and above 250Amps) are microprocessor based and below 250Amp thermal magnetic release having over current, short circuit & earth fault protection.

Outgoings -3nos. (Each Comprising of) ( 2 no working + 1 Spare)

1 Nos - 800 Amp 415 V 4Pole EDO (Electriically operated Draw-out) type microprocessor controlled ACB with O/L, E/F,S/C release, shunt trip Coil suitable for operation on 24 Volt DC and Electrical interlock.

1 Set - Single core CTs800/5 A of 15 VA burden and accuracy Class - 1 for metering.

Outgoings -6nos. ( 4 nos working + 2Nos Spare)(Each Comprising of)

1Nos. - 400 Amp 415 V 4Pole Draw-out type microprocessor based MCCB with O/L, E/F,S/C release, shunt trip Coil suitable for operation on 24 Volt DC and castle key interlock.

1 Set - Single core CTs 400/5 A of 15 VA burden and accuracy Class - 1 for metering.

4 Nos - 100A 4pole MCCB ,25KA

2 Nos - 63A 4pole MCCB ,25KA

NS-14: MAIN LT Panel-LCS-4

Supplying installation testing and commissioning of extendable, compartmentalised, front operated, back openable, LT cubicle panel having ingress protection of IP 42, suitable for operation on 415 Volt 3 phase 50 HZ power supply fabricated out of 2 mm thick CRCA sheet steel and base channel of MS section not less than 100mm x 50mm x 5mm, gland plate of 3mm thick cleaned and treated in 7 tank process and power coated with approved shade with 3000Amp TPN Aluminium busbar suitable to withstand 50KA fault level for 1Sec complete with supplying & installation of following equipment including inter connection, control wiring ets as required . Ref. Standard IEC 61439 .Note: All I/C & O/G ABC &MCCB (250 Amps and above 250Amps) are microprocessor based

Incoming - BR-1 ( From Transformer)

1 No - 2500 Amp 415 V 4Pole EDO (Electriically operated Draw-out) type microprocessor controlled ACB with O/L, E/F,S/C release, shunt trip Coil suitable for operation on 24 Volt DC and Electrical interlock.

1 Set - single core CTs 2500/5A of 15 VA burden and accuracy Class - 1 for metering.

4 Set - single core CTs 2500/5 A of 15 VA burden and accuracy Class - 1 for APFCR (only one Incommer of Transformer feeder)

1 Nos. under voltage relay

1 No - Digital Load Manager suitable for reading & display Voltage, Current, Power factor, KW, KWH

1 No - Line PT 415V/110V of 100 VA burden and accuracy Class - 1

1 No - Microprocessor based IDMT relay with 1 E/F element.(Stand by E/F)

1 Set - ON,OFF,Trip, Spring Charged,Trip circuit Healthy indication LED lamp

1 Set - Trip circuit healthy test push button with indication lamp.

1 Set - R,Y,B Phase indication LED lamp with 2 Amp back up HRC fuse.

Gland plate suitable for 2500A BusDuct of 1.1 KV grade ( Top Entry)

BUS COUPLER - BC-1

1 No - 630 Amp 415 V 4Pole EDO (Electriically operated Draw-out) type microprocessor controlled ACB with O/L, E/F,S/C release, shunt trip Coil suitable for operation on 24 Volt DC and Electrical interlock.

Incoming - BR-2 ( From DG)

1 No - 630 Amp 415 V 4Pole EDO (Electriically operated Draw-out) type microprocessor controlled ACB with O/L, E/F,S/C release, shunt trip Coil suitable for operation on 24 Volt DC and Electrical interlock.

1 Set - single core CTs 630/5 A of 15 VA burden and accuracy Class - 1 for metering.

1 No. reverse power relay

1 No - Digital Load Manager suitable for reading & display Voltage, Current, Power factor, KW, KWH

1 No - Line PT 415V/110V of 100 VA burden and accuracy Class - 1

1 Set - ON,OFF,Trip, Spring Charged,Trip circuit Healthy indication LED lamp

1 Set - Trip circuit healthy test push button with indication lamp.

1 Set - R,Y,B Phase indication LED lamp with 2 Amp back up HRC fuse.

Gland plate suitable for 2x300Sq.mm Cable of 1.1 KV grade ( Bottom Entry)

Outgoings -

All Outgoing MCCB (250 Amps and above 250Amps) are microprocessor based and below 250Amp thermal magnetic release having over current, short circuit & earth fault protection.

Outgoings -3nos.( 2working +1Spare )(Each Comprising of)

1Nos.-630Amp 415 V 4Pole 50KA EDO (Electriically operated Draw-out) type microprocessor controlled ACB with O/L, E/F ,S/C release, shunt trip Coil suitable for operation on 24 Volt DC.

1 Set - Single core CTs 630/5 A of 15 VA burden and accuracy Class - 1 for metering.

1 Set - ON,OFF,Trip, Spring Charged indication LED lamp

1 Set-Trip circuir healthy test push button and indication lamp.

Outgoings -5nos.( 4working +1Spare )(Each Comprising of)

1Nos. - 400 Amp 415 V 4Pole Fix type microprocessor based MCCB with O/L, E/F,S/C release, shunt trip Coil suitable for operation on 24 Volt DC and castle key interlock.

1 Set - Single core CTs 400/5 A of 15 VA burden and accuracy Class - 1 for metering.

3Nos - 200A 4pole MCCB , 25KA

3Nos - 125A 4pole MCCB , 25KA

5Nos - 100A 4pole MCCB , 25KA

6Nos - 63A 4pole MCCB , 25KA

NS-15: LT Panel -1

Supplying installation testing and commissioning of extendable, compartmentalised, front operated, back openable, LT cubicle panel having ingress protection of IP 54, suitable for operation on 415 Volt 3 phase 50 HZ power supply fabricated out of 2 mm thick CRCA sheet steel and base channel of MS section not less than 100mm x 50mm x 5mm, gland plate of 3mm thick cleaned and treated in 7 tank process and power coated with approved shade with 500 Amp TPN Aluminium busbar suitable to withstand 40KA fault level for 1Sec complete with supplying & installation of following equipment including inter connection, control wiring ets as required . Ref. Standard IEC 61439 .Note: All I/C & O/G ABC &MCCB (250 Amps and above 250Amps) are microprocessor based.

Incoming - 1 nos. (comprising of)

1 No.- 500A 4P, MCCB as incomer

1 Set - Single core CTs 500/5 A of 15 VA burden and accuracy Class - 1.

1 Set - R,Y,B Phase indication LED lamp with 2 Amp back up HRC fuse.

BUSBARS

500A Aluminium busbars, including making necessary connections.

Outgoing

3Nos. - 250A, FP MCCB

NS-16: Feeder Pillar (For Street Light)

Supply, installation, testing & commissioning of factory fabricated feeder pillar comparasing of the following for street lighting shall be moisture, dust & vermin proof, double door, compartmentalised suitable for floor mounting complete with aluminium bus bars, incomer with MCCB and outgoing with MCB,contactor,Timer,provisions for earthing, painting, canopy, etc. complete as required as per specifications and approved drawings. Cost of foundation to be included.The Feeder Pillar shall be provided with 24 hour cyclic timer along with control lead to be mounted within the panel. The timer shall be capable of energising rated TPN contactor.

Incoming

1 No.-63A, FP MCCB

Single phase timer with battery back-up.

40 A 4P Contactor - 1 No.

Busbar

63A,415V, 3-ph. 4Wire, 25KA for 1Sec, aluminium bus bars

Outgoing

32A 4P MCB - 2 Nos

16A 4P MCB - 4 Nos

H.T Cable & LT Cable

NS-17: H.T CABLE SUPPLYING

Supplying of earthed armoured, Aluminium conductor XLPE power cables confirming to IS 7098 (Part II) amended upto date as per the following size and grade.

NS-17.1: 3C x 185 sq.mm 11KV(E) grade ( MEDCL to MRS)

NS-17.2: 3C x 240 sq.mm 11KV(E) grade ( From LCS-3 to LCS-4)

NS-17.3: 3C x 300 sq.mm 11KV(E) grade ( MRS to LCS-3)

L.T CABLE SUPPLYING

NS-18: Supply of the following size and 1100 Volts grade armoured, Aluminium Conductor XLPE insulated power cables.

NS-18.1: 3.5 C x 500 sq.mm

NS-18.2: 3.5 C x 400 sq.mm

NS-18.3: 3.5 C x 300 sq.mm

NS-18.4: 3.5 C x 240 sq.mm

NS-18.5: 3.5 C x 185 sq.mm

NS-18.6: 3.5 C x 95 sq.mm

NS-18.7: 3.5 C x 50 sq.mm

NS-18.8: 3.5 C x 35 sq.mm

NS-18.9: 4 C x 25 sq.mm

NS-18.10: 4 C x 16 sq.mm

NS-18.11: 4 C x 10 sq.mm

Earthings

NS-19: Supply, installation, testing and commissioning of Earthing Electrode with UL-467 certified Copper bonded(254 Micron) steel rods of size 17.2 mm dia and 3 meter long confirming IEC 62561-2 with Ground enhancing material (GEM25A) 2 bag (each bag of 11Kg), and tested & conforms IEC- 62561-7 (2011) . With one bi mettalic clamp for connection and FRP earthpit chamber with cover.

NS-20: Suppy of earth enhancing chemical compound for Earthing System

NS-21: Supplying and laying 50 mm X 6mm G.I strip at 0.50 metre below ground as main earth gride, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

NS-22:Supplying and laying 75mm X 12mm G.I strip at 0.50 metre below ground as main earth gride, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Safety Equipment

NS-23:Providing and fixing of Insulating Elastomeric (a genric term that includes rubbers, latex and elastomeric compounds that may be natural or synthetic or a mixture or a combination of both) mat with ISI mark of 1 mtr wide and 2mm thick to withstand 1.1 KV dielectric strength as per IS 15652-2006.

NS-24: Providing and fixing of Insulating Elastomeric (a genric term that includes rubbers, latex and elastomeric compunds that may be natural or synthetic or a mixture or a combination of both) mat with ISI mark of 1 mtr wide and 2.5mm thick to withstand 12 KV dielectric strength as per IS 15652-2006.

NS-25: Providing pair of duly tested rubber hand gloves as per IS :340715 suitable for working on 15 kV

NS-26: PORTABLE CHEMICAL FIRE EXTINGUISHERS

Supply, installation, testing and commissioning of following types of Extinguishers with provision of wall bracket (fixed with anchor fastner).

NS-26.1: 4.5 kg CO2 High Pressure Portable Fire Extinguisher, filled with Co2 Gas as per IS 15222, Gross Weight 16.4, empty weight 11.9 Kg, Control discharge mechanism fitted with 1 Meter Wire Braided Hose & Flat Horn with Diffuser Nozzle for dispersed discharge of CO2, Discharge Time 12 Sec, Average Discharge is 95%, Applicable on Class B, C and electrically started Fire, Fire Rating 21B, Internal coating is not applicable & External coating is of enamel spray painting, Powder Coated Handle, Valve Confirm to IS 3224 ISI Marked, CO2 Cylinder construction: hot spinning by seamless pipes & bearing ISI mark, Body confirms to IS 7285 and PESO APPROVED, Extinguishers confirmed to IS 15683:2006 and ISI marked.

NS-26.2: ABC Type Fire Extinguisher Cap. 4 kg Filled with Mono Ammonium Phosphate Powder 90% confirms to IS 14609, Stored Pressure Type, UGTS Pressure Gauge, Gross Weight 8.9 Kg, Empty Weight 2.9 Kg, Can Height 530 mm, Diameter 150 ± 10mm, Discharge Time 24 Sec, Controllable discharge mechanism, Jet Range 5 Meters, Average Discharge is 90%, applicable on Class A,B & C and electrically started Fire, A Rating- 3A, B Rating 21B, Can Construction : Deep drawn & CO2 Mig welded, EPDM Rubber Hose with both end Aluminum clamped, Internal Coating - Epoxy Powder coating, External Coating - Pure Polyester Powder coating (UV Resistant), Brass forged valves with safety Pin is of SS material, Sheet metal thickness : 1.8 mm, ISI Approved IS 15683:2006.

NS-26.3: ABC Type Fire Extinguisher Cap. 9 kg Filled with Mono Ammonium Phosphate Powder 90% confirms to IS 14609, Stored Pressure Type, UGTS Pressure Gauge, Gross Weight 13.3 Kg, Empty Weight 4.3 Kg, Can Height 575 mm, Diameter 180 ± 10mm, Discharge Time 31 Sec, Controllable discharge mechanism, Jet Range 6 Meters, Average Discharge is 90%, applicable on Class A,B & C and electrically started Fire, A Rating- 4A, B Rating 89B, Can Construction : Deep drawn & CO2 Mig welded, EPDM Rubber Hose with both end Aluminum clamped, Internal Coating - Epoxy Powder coating, External Coating - Pure Polyester Powder coating (UV Resistant), Brass forged valves with safety Pin is of SS material, Sheet metal thickness : 2.0 mm, ISI Approved IS 15683:2006.

NS-26.4: 45 ltr. Mechanical Foam type Fire Extinguisher filled with AFFF Foam (6%), Applicable fire class A&B, Gross Weight 87 Kg, Empty weight 37 Kg, Can Height 1285mm, Diameter 300 mm, Controllable Discharge mechanism, Discharge Time 40-180 Sec, Jet Range 10 Meters, Average Discharge is 90%, Fitted with EPDM Hose with SS spring of 300mm to avoid kink (3 meter long) & Air aspirated Nozzle, CO2 gas Cartridge of 300 gm. (Confirms to IS 4947), Can Construction : Deep drawn & CO2 Mig welded, External Pure polyester (UV Resistant) and Internal Epoxy polyester powder coated, Brass forged cap, construction as per IS 13386:1992 and ISI Marked.

NS-26.5: Supplying and installing at approved location approved make pair of 4 nos.fire buckets of 24 gauge galvanized steel sheet, standard 9 litre capacity and of round bottom shape, painted white inside and red outside and black on the bottom, inscribed with letters “FIRE” in black and gold. Cost shall be inclusive of supporting stand, hanging bars & hooks etc comply and painting providing MS stand duly painted over a coat of primer. (Distinctly identified as "WATER & SAND").

Lightings

NS-27: Indoor Lightings-LCS-3&4

Supply, installation, testing & commissioning of the following light fixtures complete with lamps, led driver, electronic ballast / Dalli Ballast etc complete in all respect . The product should conform to Luminaire Performance: IS:10322 (Part 5/Sec 3) & IEC 60598-1,IEC 60529 & Complies IEC 62384, Certification: LM 79 & LM 80 . The product should have a constant current driver, built in heat sink. LED lamp should be certified with ENEC, and IEC. All accessories required for mounting at surface/ recess /wall as mentioned in BOQ and drawings conforming to relavant IP protection and IS codes.

NS-27.1: Supply, Installation, Testing and Commissioning of Ceiling / suspended Mounted Batten type Led Luminaire with 2x18w(±10%) LED Tube light, Pre-coated CRCA sheet Steel,Cover Plate: Pre-coated CRCA sheet steel (held in position by the push-fit mechanism), End Cap: Engg. Plastic, Mounting System: Ceiling/Wall, Internal Wiring: PVC insulated single strand copper wire, similar to Bajaj Cat. no. BLRB-DB 218 +2Nos LED Tube Light ( BLRB 18W CW LED) or Equivalent.

NS-27.2: Supply, Installation, Testing and Commissioning of Ceiling / suspended Mounted Led Luminaire with corrosion resistance LED Tube light luminaire comprises PC toggles and cover made of clear polycarbonate.Clear polycarbonate cover is fixed to the housing by PC toggles.White powder coated reflector is provided.Completely prewired with accessories up to terminal block.Suitable for twin 20W LED Tube.Finish: Housing Grey.Mounting type: Surface/Suspended through SS bracket. IP65 .similar to Bajaj Cat. no BAJAJ BJI 218 LED PC Equivalent to LT/Signify.

NS-27.3: Supply, Installation, Testing and Commissioning of Recessed mounted pressure die-casted sleek down lights for soft down lighting, Construction in pressure die-cast aluminium front frame, Flat opal diffuser fixed to front frame, Recess mounting through SS springs.Polyester powder coated, Constant current external LED driver is provided. .similar to Bajaj Cat. no BGSLO Sleek 12W WH RD or Equivalent.

NS-28: Outdoor Lighting

Supply, installation, testing & commissioning of fixtures & fittings,etc complete with accessories, tube/lamp etc on pole by suitable nuts and bolts,on surface of slab/beam by 2nos (minimum) of 6 mm anchor fasteners or on wall by means of 25 x 3 mm G.I strip bend into shape & with 2 nos of wood screws nylon plug etc.suitable supporting frame fixed with rag bolts grouted on the wall/anchorfastener on the beam/on the column & other fixing accessories etc provision & connection with 1.5 sq.mm multistranded copper conductor FRLS PVC wires/2.5 sq.mm copper conductor FRLS PVC insulated earth wire etc painting with two coats of red oxide & two coats of enameled paint, all as per drawing, specifications & as per the instruction of E.I.C.

NS-28.1: Supply, installation, testing & commissioning of 30W(±5%) Solar All in One Street light Luminaire with Hybrid system. Solar Panel: 18V, 48W(±5W) (Monocrystaline Panel) with Pir Sensor, IP 65,Battery (Li-ion): 11.1 V 26 Ah, Charge Controller: MPPT, Charge Controller Efficiency: ≥ 90%, CRI > 70, Efficacy 110 Lm/Watt Visual Angle :120°, Color Temperature 5700K-6500K, Pole Dia: 50-100mm, Autonomy 2 Days Charging Time 1 Day Working Temperature -10°C to + 55°C, BIS Approved Battery Cells, Similar to Bajaj Cat. No : SOLAR BSZSL 30W or equiv.

NS-28.2: Supply, installation, testing & commissioning of of 5.0Mtr. height dip galvanised octagonal pole made of HT steel of grade S355 of BSEN 10025 with 130mm bottom A/F & 70mm top A/F made up of 3mm thick G.I. sheet along with base plate of size 200x200x12mm thick with in built terminal box for cable connection as required. Foundation bolts, nuts, connectors, MCBs and foundation detail drawing are in the scope of bidders. .

NS-28.3:Supply, installation, testing & commissioning of 50W(±5%) Solar All in One Street light Luminaire with Hybrid system. Solar Panel: 18V, 75W(±5W) (Monocrystaline Panel) with Pir Sensor, IP 65, Battery (Li-ion): 12.8 V 39 Ah, Charge Controller: MPPT, Charge Controller Efficiency: ≥ 90%, CRI > 70, EFFICACY 120 Lm/Watt Visual Angle :120°, Color Temperature 5700K-6500K, Pole Dia: 50-100mm, Autonomy 2 Days Charging Time 1 Day Working, Temperature -10°C to + 55°C, BIS Approved Battery Cells. Similar to Bajaj Cat. No : SOLAR BSZSL 50W or equiv.

NS-28.4: Supply, installation, testing & commissioning of 8 Mtr.height dip galvanised octagonal pole made of HT steel of grade S355 of BSEN 10025 with 130mm bottom A/F & 70mm top A/F made up of 3mm thick G.I. sheet along with base plate of size 200x200x16mm thick with in built terminal box for cable connection as required. Foundation bolts, nuts, connectors, MCBs and foundation detail drawing are in the scope of bidders. .

NS-28.5: Supply, installation, testing & commissioning of 45W LED INDIRECT LIGHT Integral post top LED lantern, Graphite grey powder coated aluminum spigot,Clear toughened glass, White painted aluminum reflector fixed on tripod directing the light downwards, Mounting suitable for 100 mm OD pipe,Fully vermin and weatherproof,High bright LED for better output,Constant current electronic driver provided with high voltage, open & short circuit protection,Built-in Surge protection of 4kV & External Surge protection of 10 kV, IP65 & IK05, System Wattage of 45W, Lumen of 3600 Lumen. Correlated Color Temperature of 5700K ± 355K & CRI >70. Suitable for Pole 4M Luminaire Bajaj Cat. No : Bajaj BRIL 45W LED WH INDIRECT LIGHT or equivalent.

NS-28.6: Supply, installation, testing & commissioning of 4M URBAN ARCHITECTURE LIGHTING DECORATIVE POLE Type Bajaj BJPL 01 400.Black painted Galvanised pole, (Ø76mmx3.2mm ‘A’ class)in different cross section with gold colour painted decorative cast aluminium rings.Base plate is welded to pole (Ø140mmx4.5mm ‘B' class) with 4 nos. mounting holes.Integral connector block for loop in loop out is flushed in bottom section of the pole. foundation detail drawing are in the scope of bidders. .

APFC PANELS

NS-29: APFC Panel (300 KVAR - 2x12.5+ 1x25+5x50- 6step)-LCS-3

Supplying, installation, testing and commissioning of automatic power factor correction panels (Fabricated out of 2/1.6mm thick(Gland plate shall be 2mm) CRCA sheet steel encloser) of following size(KVAR) of capacitors suitable for 440 Volts 3 phase,50Hz, floor or Wall mounted & having MPP (Metallized Polypropylene) type with 7% Detuned harmonic block reactor , self fusing, low loss, self healing, resin bonded without oil, single phase delta connected capacitors (confirming to IS13341:1992 & IS 13440:1993 ) housed in alluminum cans & having current limiting contacts circuit to suppress switching in rush current & having 4 to 8 step microprocessor based APFC relay with digital display controlling capacitors of following rating for improvement of targeted P.F ( 0.8 to 0.95). of the system.The APFC Panel shall be fully type tested at an Independent Laboratory and shall comply with IEC 61439-1&2 and IEC 61921 Or IS-16636-2017. The degree of protection of enclosures system of the APFC Panel shall be min. IP42 indoor type front access in accordance with IEC 60529 .Average daily temperature: +35°C max, Ambient temperature: -5°C to 40°C, Maximum altitude: 1500 m above sea level.Approved Makes- ABB / Schneider /L &T/ Siemens make only. The OEM's specified cannot authorize any other partners / sub vendors to manufacture APFC Panels on their behalf. The APFC Panel manufactured by OEM's only will be accepted & factory acceptance test ( FAT ) will be carried out at OEM's plant only.

Incoming - 1 nos. (comprising of)

1 No.- 800A TP 36KA (Icu=Ics) MCCB with Microprocessor base, as incomer

1 Set - Single core CTs 800/5 A of 15 VA burden and accuracy Class - 1.

1 No - Digital multi function meter suitable with modbus communication

1 Set - R,Y,B Phase indication LED lamp with 2 Amp back up HRC fuse or MCB

BUSBARS

1000A Aluminium busbars, including making necessary connections.

Outgoing

2Nos.-32A 25KA (Ics=Icu), TP MCCB

1Nos.-63A 25KA (Ics=Icu), TP MCCB

5Nos.-125A 25KA (Ics=Icu), TP MCCB

2Nos-32A TP power contactors and ON - OFF push buttons.

1Nos63A TP power contactors and ON - OFF push buttons.

5 Nos-125A TP power contactors and ON - OFF push buttons.

Automatic power factor correction relay (APFCR)

Microprocessor based automatic power factor correction relay with all accessories for sensing of power factor of the system and initiating corrective action( for 'cutting in' or 'cutting out' of required number of capacitor banks) including step controller, reversing mechanism, time delay and following protection like over voltage, under current and loss of power.RS 486 Comunication , Duel Sensing for DG & EB, Over Voltatage & V THD protection , Thermostat for Temparature protection & Fan Control . Compatable to monitor thru EMS/BMS/SCADA

1 Set - ON/OFF indicating lamps for each bank of capacitors.

Step of Capacitor banks (300KVAR)

8step- 2x12.5+ 1x25+5x50

NS-30: Only Installation, testing and commissioning of following Exisiting automatic power factor correction panels.

NS-30.1:200KVAR

NS-30.2: 50KVAR

HVAC WORKS

NS-31: Non VRF Hi Wall Split Unit Supply, Installation, Testing and commissioing of hi wall type inverter rotary compressor based technology air conditioning units complete with centrifugal fan, multirow cooling coil, drive motor, casing, drain pan, drain pump, filters etc, matching suitable capacity of ODU unit from same OEM (outdoor installation) with microprocessor control, Automaitc voltage stablizer, mounting frames, Safety controls, cabling & Refrigerant pipe with minimum 19 mm EPDM insulation between indoor and outdoor units etc. Units are included with all Refrigeration Controls like thermostatic Expansion valve, Solenoid valve and insulated drain pan with drain piping connection to the nearest drain point etc. as required and as per specifications & drawings. The refriegerant piping and control cables shall run over the GI cable tray. Price shall be inclusive of: -- Necessary support -- Cordless remote and necessary reciever. -- Necessary first filling of refrigerant. -- Necessary sequential controller for on/off operation & changover as necessary Sound level at 1m distance shall be less than 40 dBA.All other parameters as per the technical specifications given in the tender.

Inline Fans - Explosion Proof (ATEX) Supply, installation, testing and commissioning of duct mounted Explosion Proof Inline fan complete with direct driven centrifugal fan, TEFC squirrel cage induction motor, heavy gauge sheet metal casing, rubber isolator mounts and other accessories, Hydrogen Sensor, cables, etc. as required and as per specification/drawings. Fan shall be ATEX rated for Hydrogen gas. Explosion proof version comply with EN 60079-0, EN 60079-7, EN 14986, DIN EN ISO 80079-36 and DIN EN ISO 80079-37. Explosion proof fan - 100 cfm, ESP- 8 mm water column

NS-32.1: 200 mm dia - Minimum air flow at given SP- 147 cfm

NS-32.2: 315 mm dia- Minimum air flow at given SP- 882 cfm

NS-32.3: 400 mm dia, Minimum air flow at given SP- 2352 cfm

EXTERNAL FIREFIGHTING WORKS

NS-33: MS cabinet fabricated from 16 gauge MS sheet with full front glass door and locking arrangement duly painted. (700mm x 600mm x 250mm).

Bidder Name

Amount

shiv electric(GSTN-07AACFS2722H1ZF)

HITECH ERECTORS PVT. LTD.(GSTN-07AAACH0859B1Z0)

KHAGEMBA TRANSMISSION AND CONSTRUCTION(GSTN-NA)

Bidder Name

Amount

shiv electric(GSTN-07AACFS2722H1ZF)

HITECH ERECTORS PVT. LTD.(GSTN-07AAACH0859B1Z0)

KHAGEMBA TRANSMISSION AND CONSTRUCTION(GSTN-NA)

Bidder Name

Amount

shiv electric(GSTN-07AACFS2722H1ZF)

HITECH ERECTORS PVT. LTD.(GSTN-07AAACH0859B1Z0)

KHAGEMBA TRANSMISSION AND CONSTRUCTION(GSTN-NA)

shiv electric

HITECH ERECTORS PVT. LTD.

shiv electric

HITECH ERECTORS PVT. LTD.

shiv electric

HITECH ERECTORS PVT. LTD.

shiv electric

HITECH ERECTORS PVT. LTD.

HITECH ERECTORS PVT. LTD.

shiv electric

shiv electric

HITECH ERECTORS PVT. LTD.