Beautification and development of various parks in MC Sampla

Amount

Earth work in filling with average lead of 10 Km.

The decorative poles are made of Durable Mild Steel with a total height of 3 mtr above ground level. The pole bottom section of 114mm dia x 3.2mm thickness x 1000mm long and top section of 76mm dia x 3mm thickness x 3000mm long. The Decorative base plate dimension Ø247mm as per drawing. All pole section Shall be welded by certified welders using high and MIG welding process. The Service door shall be provided at bottom part of the pole to accommodate a built-in connection box. The control gear tray is prewired with MCB, terminal connectors for loop in loop out arrangement. The base plate of the pole is design with elongated foundation holes for fine alignment of the pole during installation. Nano Ceramic surface conversion, resistant to corrosive environment. Pole primarily coated with primer than epoxy resin and top coated with UV stabilized MRF PU PAINT or Powder coated and cured. Shell pole install with LED post top light in 30W with specified design of circles which gives soft homogenous light distribution for landscape area. The post part has dia 450mm and 850 mm long with a mounting spigot. The optical system has been carefully engineered to provide correct illumination and enhanced security. Fitting is of total height 3.5mtr with Decorative pole as per attached drawing. Post top is completely weather protected and suitable for outdoor lighting application. Light is wired with Branded OSRAM or equivalent make LED and constant current driver. Proper thermal management for longer life of fixture. Color tolerance 3 SCDM to avoid color deviation. All the LED to be tested LM80 test method. Light output of source is more than 110lm/ watt, CRI)80, Surge protection 3 k, operating voltage 140-270V. Led burning of 50,000 hours. Fitting is IP66 complete in all aspects with all accessories except foundation bolt.

Supply, installation, testing and commissioning of Fountain complete in all respect up to statisfaction of Engineer In charge. Civil Work, 6 Set Flower`s jet effect, Centre hollow jet, 4 Revolving jets, 3 and` dia ring jets 1 sunburst effect jet, 12 1` size stainless steel solenoid valve, 6 2` stainless steel solenoid valve, water pipe fittings, Submersible pump 3HP 3 phase, Electrical work etc.

Supply, erection and testing of 12 Watt LED Bulb and designer light globe for poles complete in all respect specification as per Engineer in charge.

Providing and fixing with all nessery items including prepration of foundation Multi Play Station Age Group- 6 To 12 Years. Safety Play Area - 25*15 FT, Spiral Slide, Standard Slide, Double Deeker Slide, FRP Turnal Bridge, FRP Parafit= 2*2, FRP 2 Canopy, Pipe= 75 MM, 25 MM, 14 Guage Apolo Pipe ISI Mark. Paint= To Coat Colour Aspa Paint. All complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc.

Providing and fixing with all nessery items including prepration of foundation four seated MGR Age Group- 6 To 12 Years. Safety Play Area - 6 * 6 ft, H=4 FT, FRP SIT= 60 MM,25 MM, 32 MM. Bearing= 130 MM 2 Bearing. 14 GUAGE APOLO PIPE ISI MARK. Paint= To Coat Colour Aspa Paint. All complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc.

Supply and fixing of Straight Slide Slider should be made of HDPE (Pipe) of ID 40 and OD 50 with nylon bush (mat finish) of demanded colour. With structural parts GI pipes and MS steel (including cutting, fitting, welding, Bolting and smooth grinding etc. complete. All the structural parts shall be polyester powder coated having min. thickness of 50 micron. High quality fastened complete with supply/fixing and installation to ground including civil work for making base and pedestals. All complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Supply and fixing of See-Saw, safe play area=1.0 to 1.5m*3.0 to 3.6m sitting area should be coated with polyester fibre glass reinforced plastic of 6 to 8 mm thickness. For structural parts GI Pipes and MS Steel (including cutting, fitting, welding, bolting, bearing and smooth grinding etc. ) complete. All the structural parts shall be polyester powder coated having min. Thickness of 50 micron. The structural parts should not to be painted, For structural parts stainless steel should be used. Nowhere Iron to be used Entire product is assembled with nut bolts, flanges and couplings. High quality fastened complete with supply/fixing and installed to be ground including civil work for making base and pedestals. All complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Providing and fixing ground level Climber with all necessary items including preparation of foundation, age group - 6 to 12 years Safety Play area - 20 * 8 fit Climber Height - 8 fit Structure - CR Pipe ISI Mark apollo Support - 60 MM, 32 MM, 25 MM OD CR Pipe, Color full Aspa paint. All complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc.

Providing and fixing ground level Duck Spring Rider with all necessary items including preparation of foundation, Age Group- 6 To 12 Years. Safety Play Area - 2 * 3 ft, H=2 FT, FRP Duck, Spring, Pipe= 75 MM, 60 MM AND 50 MM, 14 gauge apolio Pipe ISI Mark. Two Coat Colour Aspa Paint. All complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc.

Providing and fixing with all nessery items including prepration of foundation two seated swing Age Group- 6 To 12 Years. Safety Play Area - 10*8 ft, Chain= GI Rubber Coat Chain Belt, Padestal Bearing, Pipe=60 MM, 14 Guage Apolo CR Pipe ISI Mark. Paint= To Coat Colour Aspa Paint. All complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc.

Leg press (BOTH SIDE) 90 x20x75 inches Equipment made to meet EN 16630 ,Epoxy coating of 100 microns GI main post-of:114 mm Dia Pipe thk. - 3.5 - 7.5mm Self-lubricating German bearing and Reinforced foot pedals for extended life Non fading LLDPE and open ends of the pipe closed by GULLDPE caps High tensile steel with galvanized nut bolts are used for assembly. Self Explanatory stainless steel label fixed on equipment for ease of use.

Seated Puller DIMENSIONS: - 1.9M (L) x 0.74M (W) x 1.92 (H). Seated puller equipment made up of “B” Class G.I. pipe. 100NB made from “B” Class G.I. pipe. Bottom support is of M.S. round plate of Ø 250 mm and 10mm thickness is welded. All linkages are made up of 25NB “B” class G.I. pipe. The handle frame is of 32NB “B” class G.I. pipe. The seat frame is of 32NB “B” class G.I. pipe, To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class. Welded with M.S. round plate of Ø250 mm and 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 1.2 mm thickness and 20mm x 40mm CRC square pipes of 2mm thickness. Foundation cover Closing Cap is made from FRP Material with 0.7 mm Thickness. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and Powder coated 40 microns fixed in cc foundation.

SHOULDER BUILDER DIMENSIONS: - 0.9M (L) x 0.9M (W) x 1.580M (H). Shoulder Builder Equipment made from “B” Class G.I. pipe of different NB.100mmNB made from “B” Class G.I. pipe, and the bottom support of M.S. Round plate of 250 mm diameter and 10mm thickness. The handle movement frame is of 25mm NB made from “B” Class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80mm NB”B”or “B” class welded with M.S. round plate of Ø250 mm and 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angle of 1.2 mm thickness and 20mm x 40mm CRC square pipe of 1.2mm thickness. Closing Caps are made up of high quality Fiber reinforced Plastic material. The pins used are made up of Ø 25 mm of bright material. The bearing used is “6201zz” and “6205zz” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nut bolts are used for assembly. The cerclips used for assembly is of A 24. The nylon bush is used for handle knob. The powder coating is done with Pure Polyester powder of ,Ackzonoble or Berger. with 60 to 70 micron thickness

SIT UP BOARD DOUBLE DIMENSIONS: - 1.76M (L) x 1.14M (W) x 0.66M (H). he Sit up Board double made from “B” Class GI pipe. Center column made from 100mm T NB “B” class G.I. Pipe. The main frame is of 25mm NB made from “B” Class GI pipe. FRP sheet of 3mm thickness is molded on main frame.The remaining frame of the sit up board is of 32mm NB made from “B” class GI pipe. The powder coating is done with Pure Polyester powder Ackzonoble or Berger Paints with 60 to 70 micron thickness. The oundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” f class Welded with M.S. round plate of Ø250 mm and 10mm thick. Main pipe supported with25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of The powder coating is done with Pure Polyester powder of ,Ackzonoble or Berger. with 60 to 70 micron thickness

HORSE RIDER DIMENSIONS: - 1.18M (L) x 0.4M (W) x 1.4m (H). Horse rider equipment made from “B” class G.I. 100NB made from “B” Class G.I. pipes welded with M.S. round plate of Ø250 mm and 10mm thick Seat provided are made up of MS deep draw quantity of 2mm thickness with no joint with uniform outer edge radius 20mm. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class Welded with M.S. round plate of Ø250 mm and 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 1.2 mm thickness and 20mm x 40mm CRC square pipes of 1.2mm thickness. The leg movement frame is of 32NB made from “B” G.I. pipe. The handle frame is of 32 NB made from “B” Class G.I. pipe. The footrests are made from 25 NB “B” class G.I. pipe. Pins used of Diameter 17 mm are made up from bright material. The bearings used are “6203 ZZ” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts and bolts are used for assembly. The circlips used for assembly are of A24 mm. The powder coating is done with Pure Polyester powder of ,Ackzonoble or Berger. with 60 to 70 micron thickness

CROSS TRAINER DIMENSIONS: - 1.32M (L) x 0.6M (W) x 1.75M. (H). Cross trainer equipment made from “B” Class G.I. Pipe of 80NB “B” Class G.I. Pipe with single bend pipe with 250mm radius. of M.S. round plate of Ø250 mm and 10mm thick. The Handle Frame is made up of 25NB “B” Class G.I. Pipe. M.S. round plate of Ø250 mm and 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 1.2 mm thickness and 20mm x 40mm CRC square pipes of 1.2mm thickness. To build structure bushes are used which are made from M.S.seamless pipe of 60mm OD. With 5 mm thickness. The footrests are made from casting material of size 130 mm X 310mmX5mm thickness and mounted on M.S. Plate of Size 130mmx310mmx3mm thick Closing Caps are made up of high quality Fiber reinforced Plastic material. Pins used of Diameter 35mm, 25mm, and 17mm are made up from bright material. The Bearings used are of “6007” , “6205” and with 150 x 150 x 5 mm MS plate for nut bolting with stand. Powder coated 40 microns fixed in cc foundation

CHEST PRESS DIMENSIONS: - 2M (L) x 0.71M (W) x 2.15M. (H). Chest press equipment made up of “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters The centerpipe is of 100NB made up of “B” Class G.I. pipe. The bottom welded with support of M.S. round plate of Ø250 mm and 10mm thickness. The connecting pipes are made up from 25NB “B” class G.I. pipe. The handle frame is made up from 32NB “B” class G.I. pipe. To build structure bushes are used which are made from MS seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class Welded with M.S. round plate of Ø250 mm and 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness.The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Closing Caps are made up of high quality Fiber reinforced Plastic material. Foundation cover Closing Cap is made from FRP Material with 0 The powder coating is done with Pure Polyester powder of ,Ackzonoble or Berger. with 60 to 70 micron thickness

Bidder Name

Amount

Lakariya Construction Co(GSTN-NA)--1138566

CHANDER SHEKHAR CONTRACTOR(GSTN-NA)--1139417

virender hooda contractor(GSTN-NA)--1139307

CHANDER SHEKHAR CONTRACTOR

virender hooda contractor

CHANDER SHEKHAR CONTRACTOR

virender hooda contractor