8202 SPECIAL REPAIRS TO BLDG No. P-70F AT MINTSD AND PROVN OF ONE SEPERATE ROOM OF STORAGE OF HIGH COST OF DRUGS AT MEDICAL STORE OF CHSC PUNE UNDER GE SOUTH PUNE

Amount

Dismanting water tank of capacity exc 250 & n exc 500 ltr and removing to store complete all as specified and as directed.

Disconnecting excistiong tanks, setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting & fixing in position. (cleaning, repairing etc. measured sperately) of capacity exc 250 & exc 500 ltrs complete all as specified and as directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting & fixing in position (cleaning, repairing etc. measured sperately) of capacity exc. 500 & not exc 1000 ltrs complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank 500 Litres capacity ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I with 25 mm ball valve high pressure PTMT with rod & high density plastic ball complete all as specified and directed by Engineer-in-Charge.

Removing of old water proofing treatment incl screed bed and cleaning the surface of slab with wire brushes removing dust foregin material incl flushing at junction of walll and removing the rubbish off the premises to a distance exc 500 m all as directed by Engr-in-Charge

M & L for water proofing treatment to roof slab, wall, chajjas etc; shall be carried out as specified below and as directed by Engr-in-Charge (a) M & L for 10mm thick plaster screed bed layer in CM 1:3 on concrete surfaces (b) Preparing plastered surfaces of roof slab, walls, chajjas etc; by proofing with broom sweeping free from dust etc; evently applying a coat of approved bitumenous primer @ 0.20 Kg/Sqm of area complete all as specified (c) Laying APP polymer modified approved membrane, non woven, polyster, weighing not less than 3.50 Kg/Sqm with laps & overlaps as specified & joints sealed and applied complete by torch appplication method all as speciifed & directed by Engr-in-Charge. Carrying out test by flooding water for 24 hrs for leakage & seepage and rectifying the same to the entire statisfactory of GE (d) Finally applying a coat of solar reflective bitumenous aluminium paint @ 0.15 ltr/Sqm on the top of membrane surfaces complete all as speicifed & as directed by Engr-in-Charge

Demolition of Brick/block/stone masonary built in CM complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for

Dismantling stone slab/tiles of any description or thickness, laid, bedded & pointed in cement mortor in floors, hard standing, Apron etc complete all as specified and as directed.

Demolition of cement concrete in ground floors and paving not exc 15cm thick (below or above ground level incl sunken slab) un-reinforced complete all as specified and as directed.

Taking down cement plaster on brick/ block walling including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for

Taking down chowkats or frames wooden/steel with shutters (without taking off shutters from frames) exc 1.5 Sqm and n exc 4 Sqm each complete all as specified and as directed.

Taking down shutters of any description exc 1 sqm and n exc 2 Sqm each complete all as specified and as directed.

Dismantling wrought iron or mild steel iron of any description not otherwise provide for complete all as specified and as directed.

Taking down GI steel tubing 15mm bore complete all as specified and as directed.

Taking down GI steel tubing 20mm bore complete all as specified and as directed.

Taking down plaster on ceiling complete all as specified and as directed.

M & L PVC (SWR) floor trap, plain with grating incl jointing with solvent cement dia of outlet 75mm complete all as specified and as directed.

M & L PVC (SWR) gully trap 125/110mm setting and jointing with solvent cement complete all as specified and as directed.

S & F PVC (SWR) branch piece, single (Single Y) equal or unequal 75mm complete all as specified and as directed.

S & F PVC (SWR) branch piece, single (Single Y) equal or unequal 110mm complete all as specified and as directed.

S & F PVC (SWR) bends any radius 75mm bore complete all as specified and as directed.

S & F PVC (SWR) bends any radius 110mm bore complete all as specified and as directed.

S & F PVC (SWR) branch piece, single (single Y) equal or unequal provided with access door 110mm bore complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc, and cutting chases for concealed water tubing or concealed conduit wiring, etc complete all as specified and as directed.

Refixing 15mm dia old steel tubing and connections in new or old position complete to wall and ceiling or laid in floors etc complete all as specified and as directed.

Refixing 20mm dia old steel tubing and connections in new or old position complete to wall and ceiling or laid in floors etc complete all as specified and as directed.

S & F 15 mm bore, steel tubes, galvanised, medium grade with all fittings & fixed complete to wall and ceiling or laid in floors etc complete all as specified and as directed.

S & F 20 mm bore, steel tubes, galvanised, medium grade with all fittings & fixed complete to wall and ceiling or laid in floors etc complete as specified and directed.

M&L for 12mm thick rendering on fair of brick work or concrete surfaces in Cm 1:6 incl of sagol of finish on plastered surface of internal wall & ceiling complete all as specified and as directed.

M&L 15 mm thick rendering in two layers i.e 5 mm thick in cement mortar 1:4 mixed with water proofing compound over backing coat of 10 mm thick in cement mortar 1:4 complete all as specified and as directed. (Note : WPC shall be measured and paid separately under relevant item of this Schedule).

M&L for rendering 10mm thick in cement mortar 1:3 on fair faces of brick work or concrete surfaces as in as in ceiling complete all as specified and as directed.

M&L for Brick work with flyash brick & straight or curved on plan to any radius in half brick thick walls built in old size bricks in CM 1:4 complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and as directed.

S&F TMT steel bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete as in reinforcement as specified an directed.

All as per Sl. Item No. 36.00 above but 6mm to 8mm Dia complete all as specified and as directed.

All as per Sl. Item No. 36.00 above but 5mm dia and over up to and incl 10mm dia in stirrups, spaces and binder complete all as specified and as directed.

M&L for RCC 1:2:4, Type B-1 (using 20mm graded stone aggregate) as in slab supported on walls, beams and columns in floors, roors, landings, balconies, canopies, deck slab and in shelves and the like all as specified and directed.

M&L for RCC 1:2:4, Type B-1 (using 20mm graded stone aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span all as specified and directed.

S & F pressed steel frame for doors with one & more rebates incl necessary fixing lugs, hinges, lock strike plate etc complete as specified size of frame 125 x 60mm. Incl MS hold fast, PCC bedblock (1:2:4) type B1 for hold fast and cement concrete 1:3:6 type C1 (12.5mm graded stone agg) for filling in MS frame complete all as specified and as directed.

S & F 35 mm thick, 2nd class hardwood plain, framed, panelled shutters (any number of panels), with panels of (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers fitted to chowkats complete all as specified & directed.

S & F 30 mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc, divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, stiles & rails as specified in SSR Part I Section 8 clause 8.24 (b) complete all as specified and as directed.

S&F fixed glass ventilators using 5mm thick plain glass and following aluminium powder coated section confirming to catlogue of Jindal or of equivalent make and rubber beading etc complete all as specified and as directed. (a) SP-2008 (b) Glazing clips 19352

S&F three track sliding window with two or more shutter with 4mm thick tinted glass one shutter using stainless steel wire cloth 0.36mm nominal dia & 1.18mm width aperture for mosquito proofing with good quality bearing handle, lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified and directed by Engr-in-Charge. (Make : Hindalco/Indal/Ajit India pvt ltd) (a) Bottom frame 20620 (b) Top frame & vertical 20621 (c) Handle (side) 20606 (d) Shutter inter lock 20724 (e) Shutter top & bottom 20844

S&F sliding door shutter of Aluminium with guide rails and shutter with 100/150 mm styles and rails to run on standard quality runners with pannels of prelaminated MDF board in half portion and 6mm thick glass on upper portion duly secured with aluminium bedding and rubber gassked etc, aluminium section of Jindal/Hindalco 3mm thick

S&F two track sliding shutter as in cupboard shelves with two or more shutter with 4mm thick tinted/plain glass with good quality bearing handle, lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified and directed by Engr-in-Charge. (Make : Hindalco/Indal/Ajit India pvt ltd) (a) Bottom frame 20620 (b) Top frame & vertical 20621 (c) Handle (side) 20606 (d) Shutter inter lock 20724 (e) Shutter top & bottom 20844

S&F Aluminium anodised Powder coating of ivory colour frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing, screws etc complete all as specified and as directed.

M & L Water proofing treatment to sunken slab, walls, etc, shall be carried out as specified below and as directed by Engineer-in-Charge. (a) Clean the sunken portion of toilet/Baths/WCs/Kitchen thoroughly remove laitance, dirt, dust etc. (b) Form angle fillet of size 40 mm x 40 mm along the junction of wall and floor using polymer modified mortar (“ Dr fixit” Pidicrete URP” or eqvt). (c) Sanitary pipes entering through walls and floor shall be sealed with “Dr Fixit Bathseal Tape” and the gaps to be grouted with non-shrink cementitous grout “Dr Fixit Bathseal Grout” or eqvt. Nahani traps etc to be fitted securely and the gaps around it to be grounted in the same manner. (d) Apply one coat of a Bitumen-modified polymer coating “Dr Fixit Bathseal Plus” or eqvt on all angle fillets by brush and cover it with 100mm open woven mesh when it is still wet. Apply second coat of the same coating on the angle fillets and allow it to dry completely. ITEM No. 49.00 Contd...

ITEM No. 49.00 Contd... (e) In the remaining area, in dry substrate condition brush apply first coat of the same coating and further apply second coat when first is dry. Extend the coating upto 150mm above the FFI. Above FFI, another cementitious waterproofing waterproof coating “Dr Fixit Pidifin 2 K” or eqvt can be further applied right upto 2.1 m to waterproof the shower area also, if it is a bathroom or bath cubicles of a sanitary annex and apply second coat after 6-8 hours and allow to dry completely.(f) After 2 to 3 days, sunken portion must be overlaid with a 50 mm thick concrete screed M 15 type B0 mixed with integral WPC (Liquid) laid to slope 1:60 towards outer face of wall. Provide 40 mm OD UPVC pipe at the lowest point with 300 mm projection beyond the outer face of the wall. Then fill up the sunken portion with lean concrete 1:5:10 type E2. (g) After completing plumbing work in the toilet/WC/Bath/Kitchen floor, tiling work (floor and dado) can be carried out using suitable Tile Adhesives and ready to make tile grouts of appd makes such as Dr Fixit, FOSROC SIKA, MC BUCHEMIE, ROFF, etc. (Note : For Payment of Sunken,only plan area of Sunken slab will be measured.)

M&L for PCC 1:5:10 type E2 (using 40 mm graded brick aggregate)lean concrete for filling sunken floor etc. complete all as specified and as directed.

M&L for PCC type B1 1:2:4 (25mm graded aggregate) as in sub floor for tile work complete all as specified and as directed.

M & L for granite 18mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, Door cills ,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Rounding to edges of granite stone, such as in steps, cooking platform and other similar situations complete all as specified and as directed.

M&L for coloured non-skid ceramic tiles 7 to 8 mm thick area of tiles exc 0.16 sqm but not exc 0.36 sqm etc.in floors, set an jointed in neat cement slurry and pointed in white or coloured cement to match including laid over 20 mm thick screed bed in CM (1:6) complete all as specified and as directed.

M&L for preperation of new plastered surface by brooming down and scrapping wherever necessary and applying two coat of Apex Ultima Weather shield paint or tinted over a coat of primer all as specified.

Complete removal of existing treatment of walls by scrapping, cleaning by water jet, soffits/facia of chajja/roof slab etc and applying two coat of Apex Ultima Weather shield paint or tinted over a coat of primer etc complete all as specified and directed

M&L for Glazed ceramic tiles in vertical surfaces 300x600x5.5 to 6mm thick, coloured, glazed ceramic set and jointed in neat cement slurry and pointed in white or coloured cement to match colour over 10mm thick rendring in CM (1:4) complete all as specified and directed.

S&F in repairs viterous China squatting pan "orrissa" pattern size 580 X 440 mm, White with integrated footrest incl 10 ltr PVC valveless syphonic action type, flushing cistern Low level white with inlet valve, float and handle incl bracketes & flush pipe and waste pipe complete all as specified and as directed.

S & F Machine cut cuddappa stone slab one side polished 20 to 25mm thick, set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 20mm screed bed in cement mortar (1:6) complete all as specified and as directed.

S&F 110mm bore PVC (SWR) WC connector with Lip ring comlpete all as specified anfd directed.

S&F Vitreous China wash basin (WHB), white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets & making good the damaged portion of wall or floor complete all as specified and as directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chormium plated bracket guard and railing 60cm long complete all as specified and as directed.

S&F towel rail 600mm long of PTMT fixed with and incl chromium plated brass screws and wooden/plastic cleats (minium weight 190gms) complete all as specified and as directed.

M & L preparing new/old plastered or unplastered surfaces of ceiling and applying two coats of white wash complete as specified and directed.

M&L for two coats of oil emulsion distemper over a coat of clearcolle on plastered and other surface, preparatory to distemper including preparetion of new/old plastered surfaces complete all as specified and as directed.

Supply only integrated water proofing compound complete all as specified and as directed.

S&F Butt hinges 100mm extruded aluminium alloy with galvanised mild steel hinges pin, anodised and fixed type B-21 complete all as specified and as directed.

S&F 200 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S & F Aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clipes of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy, length of bolt of 250 mm complete all as specified and as directed.

S&F 150mm aluminium anodised handle, fabricated type complete all as specified and as directed.

S&F glavanised mild steel wine cloth 0.63mm nominal dia of wire and average width of aperture 1.4mm & fixed with tinned tacks or galvanised wire stapple as fixed in gauged shutter complete all as specified and as directed.

S&F floor door stopper of aluminium allody body and tongue anodised with hard drawn steel spring fixed in 140mm length of overall cover plate complete all as specified and as directed.

S&F Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours; articles not exc 200 cu. cm each complete all as specified and as directed.

All as per Sl. Item No. 74.00 above but fixed in repair complete all as specified and as directed.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290, Gde-E-165 complete all as specified and as directed.

M&L for two coats synthetic enamelled paint on steel surfaces of any description, over 10cm in width or girth over a coat of red oxide including preparation of new untreated steel surfaces not otherwise described complete all as specified and as directed.

M&L one coat of synthetic enamelled painting on steel surfaces of any description n exec 10 cm width or girth incl perparation of old painted steel surfaces not otherwise described complete all as specified and as directed.

M&L 2 coat synthetic enamelled painting over a coat of pink primer incl preparation of new/old wooden surfaces of any description not otherwise descrived over 10cm width or girth complete all as specified and as directed.

S&F brass hat & coat hooks sided body 175mm to 25mm complete all as specified and as directed.

S&F Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F stop valve cast copper alloy, fancy type chromium plated with long shank and cup (concealed type) of bore 15mm dia of pipe complete all as specified and as directed.

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed of 15mm bore dia of pipe complete all as specified and as directed.

S&F Bib taps, CP cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed of 15mm bore of pipe complete all as specified and as directed.

S&F Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed of bore 20mm dia of pipe complete all as specified and as directed.

S&F brass chromium plated shower rose 125mm size complete all as specified and as directed.

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F PVC (SWR) vent cowl 75 mm bore complete all as specified and as directed.

Rough excavation not exceeding 1.5 m deep and getting out in self/loose soil complete all as specified and as directed.

Removing excavated material exc. 250 m but not exc. 500 m and depositing where directed complete all as specified and as directed.

Removing building materials etc. (other than soil payable under items 03028 to 03031 in Section-3 Earthwork) to a distance of upto 1.00 km total distance complete all as specified and as directed.

M&L for 75mm thick cement concrete type C-2 1:3:6 (40mm graded aggregate) as in plinth protection, laid in alternate bays including finishing surface even & fair without using extra cement complete all as specified and as directed.

M&L for 50 mm thick cement concrete type C-2 1:3:6 (40mm graded aggregate) as in Sub-base complete all as specified and as directed.

M&L cement concrete type B1 1:2:4 (20mm graded aggregate) as in copings water troughs and the like incl weathering slightly rounded or champered angle and throughting as directed

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

All as per Sl. Item No. 95.00 above but 110 mm bore complete all as specified and as directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

All as per Sl. Item No 97.00 above but 110mm bore complete all as specified and as directed.

S&F ball brass valves high pressure, with polythelene float and flynut complete screwed for iron pipe or brass ferrule and fixed of bore 20 mm dia of pipe complete all as specified and as directed,

All as per Sl. Item No. 99.00 above but fixed in repair complete all as specified and as directed,

S&F aluminium powder coated fancy type curtain rod 25 mm bore all as specified & as directed.

S&F aluminium powder coated fancy type decorative brackets suitable for 25 mm dia curtain rod (minimum projection from wall 75 mm ) fixed to wall including drilling, rawl plug, screws etc complete all as specified and as directed.

Surface excavation not exc 30cm deep and averaging 15 cm deep and getting out in hard/dense soil complete all as specified and as directed.

M&L for PCC 1:4:8 type C2 (using 40 mm graded agg) in foundation filling and mass concrete complete all as specified and as directed.

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and as directed.

Returning filling in including spreading levelling watering and well ramming in layers not exc 25 cm complete all as specified and as directed,

Removing excavated mtrl n exc. 50 m and depositing wheredirected at a level not exc 1.5 m above the starting point complete all as specified and as directed,

M&L for rendering 10 mm thick in CM 1:6 on other than fair faces concrete/brick surfaces and finished even and smooth without using extra cement complete all as specified and as directed.

S&F solid PVC door frame of size 50x47mm made out of 5mm plain colour sheet reinforced with MS square tube all as per specification and drawing complete all as specified and as directed by Engr-in-charge

M&L Factory made solid panel PVC door shutler 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side & as lock rail & bottom rail on either side & as gap insert for top rail & bottom rail Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame a site as per specification & drawing and as directed by Engr-in-charge

S&F 200mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

S&F in repairs, vitreous china wash down water closet pan "Pedestal" coloured including fixing bolts etc including PVC seat cover white with flat bottom including MS, CP or aluminium anodised hinging devices including PVC low level flushing cistern 10 Ltr capacity with internal fitting, inlet, outlet pipe connections etc complete all as specified and directed,

S&F in repairs vitreous china wash basin (WHB), white, flat back, size 550x400mm including 15mm bore PTMT pillar tap, 32mm PVC waste coupling, PVC connection 45cm long including CI brackets fixing with fasteners etc complete all as specified and as directed.

M&L for Machine pressed precast concrete intelocking paver block any shape and any size confirming to IS 15658-2006 of 60mm thickness M-35 Grade with Grey cement and Pigment including 30mm thick sand cushioning complete all as specified and as directed.

Excavation in trenches not exc 1.5m wide and 1.5m deep getting out as in hard/dense soil complete all as specified and as directed.

Supply only integral water poofing compound complete all as specified and as directed.

Excavation in trenches not exc. 1.5 M wide and not exc. 1.5 M in depth & getting out in soft rock complete all as specified and as directed.

M&L for damp proof course 40mm thick in plain cement concrete (1:2:4) type B-0 including necessary formwork and mixed with water proofing compound complete all as specified and as directed.

Filling under floor with soil including watering & well ramming complete in layer n.exc 25 cm thick complete all as specified and as directed.

Excavating in post holes (or similar holes) in hard/dense soil each n exc 0.5 cum, getting out, incl returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and as directed.

M&L for 75mm thick PCC as in sub base 1:4:8 type D-2 (using 40mm graded stone aggregate) complete all as specified and as directed.

M&L for 50mm thick PCC (1:3:6) type C-1 (using 20mm graded stone aggregate) laid in alternative bays as in plinth protection incl finish the surface even & fair without using extra cement complete all as specified.

S&F 30mm thick flush shutters, solid core construction with block board core construction with block board core and plywood face panells commercial type on both faces incl 6mm thick 1st class HW (Teak wood) beading all around on edges complete all as specified and directed.

S&F butt hinges 100mm long medium, mild steel cold rolled and fixed complete all as specified and as directed.

S&F PVC(SWR) junction single (Single T) equal or unequal of following sizes :-

110mm bore

75mm bore

M&L for coloured vitrified tiles 800x800x8 to 10mm thick as in flooring, set and jointed in neat cement slurry and pointed in coloured cement to match with tiles, laid over and including 20mm thick screed bed in CM (1:6) complete all as specified and as directed.

S&F Aluminium single leaf door on pivots including hydraulic door closer (Aluminium Extruded Section), door lock, handles 5mm thick plain glass in top and 12mm thick prelaminated particle board (both side laminated) in bottom panel, fixed with rubber beading and glazing clips and using powder coated sections as given in 'JINDAL' Catalogue complete all as directed by Engineer-in-Charge. (a) Rectangular tube - 14005 (b) Shutter vertical - 18501 (c) Shutter top rail - 19503 (d) Shutter middle rail - 20060 (e) Shutter bottom rail - 19511 (f) Glazing clips - 19352.

S&F aluminum powder coated partition by using Jindal Sections DP/SP with frosted glass 5 mm thick and 12 mm thick prelaminiated particle board fixed with glazing clips and complete all as directed by Engineer-in-Charge. (a) SP - 20048 (b) DP - 20047 (c) Glazing clips - 19352.

S & F IInd class hard wood 35mm thick factory made, glazed and skeleton shutter open rebated and prepared to receive glass, gauge, etc.edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass,etc; The size of the rail and stile as per IS 1003 (Part-I), Kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F butt hinges 100mm size stainless steel medium weight complete all as specified and as directed.

M & L for filleting in any position and to any shape in CM 1:3 sectional area exc. 25 Sqcm but not exc. 50 Sqcm complete all as specified and as directed.

S&F in stop valves cast copper alloy,CP screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe of for unions of bore 15mm complete all as specified and as directed.

S&F in repairs CP health faucet with flexible pipe fancy type complete all as specified and directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. etc conf to Fe-410(Gde-E-250) all as specified and directed.

S&F for Gypsum ceiling board for ceiling of approved texture 595x595x9 to 9.5mm thick in size of approved brand/make, laid over and including grid work of size 600x600mm, made out of 0.5mm thick GI tee 32x24mm for main, 25x24mm for cross tee and 20x20mm angle fixed on wall, powder coated finish on exposed faces of tee and angle, hung from ceiling using 2mm thick GI suspension wires spaced at 1200mm on main runners including making niches for fans/light at as specified and directed

Supply and fixing of Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping scres as specified

Supply and fixing of painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof overing/cladding to wall, fixed with self tapping screws as specified as specified

Taking down carefully copper/aluminium point wiring (light, fan ,socket or power) complete,including fixture and fittings such as switches,ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit including making good disturbed surfaces of walls ,floors etc complete all as specified and as directed. (Note : Credit for above items should be made as per conditions separately)

Taking down MCB DB/Main switch with old unserviceable / worn out aluminium submain wiring of any type

M&L for point wiring of any length using approved colour coding as per IS, with stranded copper conductor 1.5 sqmm (Nominal area), single core, PVC insulated and unsheathed stranded FRLS cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC casing caping including all accessories etc. heavy duty ISI marked, mild steel concealed sunken boxes, 1.6mm thick and 60mm depth and earth dolly duly painted with two coats of black bituminous paint over a coat of red oxide primer with laminated bakelite sheet of min. thickness of 3mm suitable for switches / sockets etc. including PVC insulated stranded copper conductor 1.5 sqmm single core green PVC insulated FRLS cable as earth and connecting to earth dolly complete and including cutting and chases in the wall for box complete all as specified for the following :- (NOTE : Making good of disturbed surfaces and white wash / colour wash as per existing surface will be done by Contractor without any claims)

One light/one fan point controlled by one switch

One 5A 3 pin switch socket outlet mutipurpose on independent board.

One 5A 3 pin switch socket out let on same board.

One bell/buzzer point controlled by one bell push

M&L for point wiring of any length using approved colour coding as per IS, with stranded copper conductor 2.5 sqmm (Nominal area), single core, PVC insulated and unsheathed stranded FRLS cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC casing caping including all accessories etc. heavy duty ISI marked, mild steel concealed sunken boxes, 1.6mm thick and 60mm depth and earth dolly duly painted with two coats of black bituminous paint over a coat of red oxide primer with laminated bakelite sheet of min. thickness of 3mm suitable for switches / sockets etc. including PVC insulated stranded copper conductor 2.5 sqmm single core green PVC insulated FRLS cable as earth and connecting to earth dolly complete and including cutting and chases in the wall for box complete all as specified for the following :- (NOTE : Making good of disturbed surfaces will be done by Contractor without any claims)

Supply and fix switch piano flush button type 5 amps SP one way complete all as specified and as directed.

Supply and fix bell push piano 5 amps 230 V complete all as specified and as directed.

S&F Ceiling rose surface type, three terminals 240 Volts complete all as specified and as directed.

S&F bell electrical ding dong including teak wood board bull push, flush type 5 Amp 240 Volts complete all as specified and as directed.

S&F socket outlet 5 Amps 5 pin 230 Volts flush type on same board complete all as specified and as directed.

Supply and fix switch socket combination 2 in 1, 5 / 15 Amps flush type complete all as specified and as directed.

Supply and fix lamp holder, PVC / Polycarbonate type with back plate suitable for batten fittings complete with 5 watt LED lamp complete all as specified and directed.

S&F in replacement of ceiling fan regulator, electronic step type, delux, two module suitable for fan 48"/56" sweep complete all as specified and as directed.

M&L for sub main wiring complete with two single core 4 sqmm 1100 volt grade PVC insulated, unsheathed multistranded copper conductor (FRLS) cable including PVC casing & caping and accessories, including continuous PVC insulated copper earth conductor 4 sqmm complete all as directed. (Note : 3 runs of 4 sqmm cable and earth wire and 1 run of PVC casing caping shall be measured as one length.)

S&F DB MCB , TPN 4 way, double door, 415 Volts with 200 amps rated busbar, recess mounted / wall mounted complete all as specified and as directed.

S&F DB MCB , SPN 8 way, 240 Volts with 200 amps rated busbar, recess mounted / wall mounted complete all as specified and as directed.

S & F MCB SP, 6-32 Amps, C series breaking capacity 10KA all as specified and directed.

S & F MCB SPN 40Amps, 240 V,50 HZ, C series breaking capacity 10KA all as specified and directed.

S & F MCB TPN 63Amps, 415 V,50 HZ, C series breaking capacity 10KA all as specified and directed.

M&L for earthing complete with GI earth plate electrode 60cmx60cmx6.3mm thick buried directly in ground (earth pit not less than 2.25 mtr in deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level including connecting GI earth wire 4mm dia by GI nut, bolt, washers all as shown in electrical plate No. 3 of SSR Part I of 2009 including funnel for watering, PCC 1:3:6 type C-2 using 40mm graded stone aggregates as in pit / chamber, RCC 1:2:4 type B0 using 12.5mm graded stone aggregates and 6mm dia mild steel bars at 100mm c/c as in chamber cover, charcoal, salt etc complete including excavation and earth work in any strata, test point and testing on completion including filling up the earth pit with black cotton soil for best result and removal of excavated material from site all as specified and directed by Engineer-in-charge. (Note : GI earthwire and GI protection pipe upto 7.5 mtr length shall be included in this item.)

M&L for fixing earth continuity conductor or main earth lead fixed to wall or burried in ground or drawn in GI Pipe with 4 sqmm GI Wire complete all as specified and as directed.

S&F integral LED tube light fitting complete with all fitting and fixing accessories, 1 X 20 Watt pre-wired with high efficiency electronic driver, glare free, smooth light distribution conforming to CAT part No. Garnet 20 W LED (D532065) of WIPRO or of equivalent make in HAVELLS / HPL / Phillips complete all as specified and as directed.

S&F integral LED security light Luminaire 30 W comprising of epoxy powder coated aluminium housing, enclosed with glass cover in frame suitable for 50/40 mm GI Pipe (including GI Pipe) complete with accessories conforming to CAT part No. HPLLEDSL3060S of HPL or of equivalent make in Wipro / Phillips / Havells / Fortune Art including taking down old fittings complete all as specified and as directed

S&F in replacement of sleek LED Cadila mirror light fitting complete in all respect having high output diffuser of 2 feet length,9 W LED.Cat Part No HLPLEDCAD09CW of HPL or of equivalent in Havells/Philips/Wipro Fortune Art make specified here- in - after.

M&L for Point wiring using approved colour coding as per IS, with stranded copper conductor 1.5 Sq. mm (nominal area), single core, PVC insulated and unsheathed stranded FRLS cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC concealed conduit wiring including all accessories etc, heavy duty ISI marked, with pressed steel sunken boxes not less than 60 mm deep with earth dolly duly painted with two coats of black bituminus paint over a coat of red oxide primer, covered with plastic laminated bakelite sheet cover 3 mm thick for mounting accessories (switches/sockets etc) including PVC insulated stranded copper conductor 1.5 Sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly. NOTE:-Cost of concealed of terminal boxesis inclusive with point wiring rates.

One light/fan point controlled by one switch.

One Socket outlet point, 5 Amp,on independent board.

One switch socket outlet point, 5 amps on the same board

Point wiring using approved colour coding as per IS, with stranded copper conductor 2.5 Sq. mm (nominal area), single core, PVC insulated and unsheathed stranded FRLS cable 1100 volts grade ISI-694 marked for 15 amp socket outlet,independent, with pressed steel sunken boxes not less than 60 mm deep with earth dolly duly painted with two coats of black bituminus paint over a coat of red oxide primer for mounting of accessories switches/sockets etc, including PVC insulated stranded copper conductor 1.5 Sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly for the following.

Supply & fix switch socket combination 2 in 1, 3 pin, 5 amps and 15 amps multipurpose flush type complete all as specified and as directed.

Socket outlet 2 in 1, 3 pin, 5 amps complete all as directed.

Supplying and fixing LED light fitting,1X20 Watt surface mounted LED BATTEN PLASTIC high efficiency LED luminare protection : IP66 comprises OF pre-wired with high efficiency electronic driver,high trnslucent frosted diffuser gets glare free,smooth light distribution. Make -BAJAJ cat No- 830203 OR equivalent in Havells/HPL.

S & F Sheet metal, 20 amp Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amps,10 KA breaking capacity,'C' series,240 V complete all as specified and as directed.

Supply and fixing ceiling fans complete with electronic type regulator and accessories 230 volts 1200 mm sweep BEE 5 star rated including taking down old ceiling fans and deposit in MES store yard Make Havells (fusion 50 - 5 star)Bajaj cat no-250823 or equivalent in philips/ Havells

Supply and fix exhaust fan heavy duty, noise free, AC single phase 230/ 240 volts of size 450 mm sweep with louvers and all fixing arrangements conforming to Cat Part No. Bajaj cat no-70064 or equivalent in Philips/ Havells complete all as per the directions given by Engr-in-charge.

M & L for Sub main wiring complete with two single core 4 sqmm ,1100 volts grade, PVC insulated, stranded copper conductor cable with continuous copper earth conductor of 4 sqmm in and including PVC conduit for consealed including cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed conduit wiring, etc. complete all as specified and as directed.

M/s.BAJRANG CONSTRUCTION