Tiruppur Corporation_Construction of Toilet, Urinal at Bommanaikkanpalayam Corporation Elementry School in ward no.06

Amount

Earthwork excavation for foundation in all soils and sub soils except in hard rock requiring blasting and depositing on bank with initial lead of 10m and initial lift of 2m inclusive of shoring, shuttering, bailing out water wherever necessary, refilling the foundation with excavated earth other than sandy soil in layers of not more than 150mm thick layers well rammed and depositing the surplus earth within the compound in place shown by the departmental officers and clearing and levelling the site etc,. complete.

Plain Cement concrete 1:4:8 [one cement, four M-sand and eight course aggregates] using 40mm size Hard Broken/Machine crushed Granite Stone Jelly including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted etc., complete complying with standard specification.

Random rubble masonry in CM 1:5 [one cement and five M-sand] for foundation and basement using best new rough and bond stones including simultaneous pointing above ground level with the same mortar etc., complete complying with standard specification.

Fly Ash Brick work In CM 1:5 mix using best Fly Ash Bricks of size 230 x 110 x 70mm including finishing, curing etc., complete complying with standard specification.

Supplying and erecting centering for soffits of plane surfaces like RCC Slabs, Lintels, Sunshades, Square Columns, Staircase waists, Beams etc., including strutting 3m high using mild steel sheets of size 90cm x 60cm and BG 10 stiffened with M.S angles of size 25mm x 25mm x 3mm laid over silver Oak (C.W) joists of size 10cm x 6.5cm (spaced at about 90cm c/c) and supported by casurina props of 10cm to 13cm dia (spaced of 75cm c/c) etc., complete complying with standard specification.

Reinforced cement concrete 1:1½:3 [one cement, one and half M-Sand and three course aggregates] using 20mm size Hard Broken/Machine crushed Granite Stone Jelly for all RCC items of works excluding centering, shuttering and cost of reinforcement, including curing, fixing fan clamp and fixtures if necessary etc., complete complying with standard specification.

Supplying, fabricating and placing in position of Steel Reinforcement using Mild Steel or Ribbed Tor steel bars for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors etc., complete complying with standard specification.

Fabricating supplying and fixing of Galvalume Colour Sheet of size 0.47mm with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47mm thick 24 gauge having width 1050mm. The sheet should be G.I base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws and plastic washer. The washer and screws to be fixed by using minute power machine drilled without damaging the sheets paint coating to be regular modified polyester coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like Malabar Mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated, cutting the sheet in to the required size and making ornamental designs as per the site condition and as directed by the departmental officers.

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc., conforming to IS specification including primer coating and enamel painting as per design given by the departmental officers etc., complete as per standard specification.

Ceiling Plastering with cement mortar 1:3 mix (one cement three P-sand), 10mm thick in all floors for RCC slabs, Beams, Sunshades including packing, providing cement mortar beading for sunshades, staircase steps, landing slabs etc., as directed by the departmental officers etc., complete complying with standard specifications.

Plastering with cement mortar 1:5 mix (one cement five P-sand), 12mm thick in all floors using clean screened M-Sand and including cost of curing for fifteen days from the completion of the work and surface should free from undulations and including the cost of preparing the surface for plastering and protecting from other damages till setting of mortar etc., complete complying with standard specification.

Plastering with cement mortar 1:4 mix (one cement four P-sand), 20mm thick in all floors using clean screened M-Sand and including cost of curing for fifteen days from the completion of the work and surface should free from undulations and including the cost of preparing the surface for plastering and protecting from other damages till setting of mortar etc., complete complying with standard specification.

White washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder, fevicol type gum, brushes, scaffolding charges etc., complete complying with standard specification.

Painting two coats with approved Cement Paint over cement plastered wall surface, ceiling and other new surface including cleaning, preparing the surface and curing etc., complete as per standard specification.

Paving the floor with 8mm thick Double Charged Vitrified Tiles in all floors over a base layer of cement mortar 1:3 [one cement and three M-sand] 20mm thick of walls and floors and pointed with the same colour cement neatly, including polishing with electric polishers to a high degree so as to make it perfectly smooth and showing etc., complete complying with standard specification.

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable heavy gauge MS coundit pipe on wall and ceiling with continous earth wire connection of 14 SWG TC wire with painting of suitable colour

Supply and fixing of single box type 4'40W fluorescent fitting complete with copper choke and condensor with conduit pipe suspension from the ceiling with PVC unsheathed copper leads from terminals to the fitting with tube

Supply and fixing FRP door shutter with frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of hold fasts and solid core FRP shutter Panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., complete complying with standard specification.

Add GST @ 18%

VELA ASSOCIATES