PROVN OF 01 X CEMENTED GARBAGE POINT COVERED WITH IRON JAIL, PROVN OF DRAINAGE SYSTEM, PROVN OF 72 X WIRE MESH DOORS, CONSTR OF PATHWAY FOR OR MD ACCN, AND SPL REPAIR TO OR MD ACCN No. NP-20 IN AOR OF AGE BR-II UNDER GE(WEST)PATHANKOT

Amount

Sch 'A' B/R works:- Taking down chowkhats or frames exc 1.50 and n.exc 4 Sqm each (without talking off shutters from the frame) complete all as specified and directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frames) area not exc1.5 Sqm each and removing from site.

Cutting holes into or through brick walls, not exceeding half brick thick, built in cement mortar or cement lime mortar and stone walls built in lime mortar or walls of lime concrete and making good in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required, including applying two coats of oil bound distemper to match the existing surfaces complete all a specified & directed.

M&L for cement concrete type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) as in bed plates for securing hold fasts & back filling of hollow portion of chowkats etc complete all as specified and directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

S&F 35mm thick factory made 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass or wire gauze, etc. (without sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats Note: wire cloth shall be measured separately

S&F pressed steel frames for door 105 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate including one shop coat of primer complete all as spd and directed

S&F pressed steel frames for door 125 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate including one shop coat of primer complete all as spd and directed

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, confirming to IS- 2202(Part-I-1999) , ISI Marked complete all as specified and directed

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC sheet PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;Panelling of wood grain printed PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900 ) used instead of exposed portion of PVC sheet beading suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S & F Butt hinges, 100mm extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor Overall length of cover plate 140mm complete all as specified and directed.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor Overall length of cover plate 150mm complete all as specified and directed.

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed, Length of bolt in 200mm complete all as specified and directed

S&F Aluminium, anodised, barrel tower bolts of extruded section and fixed, Length of bolt in 200mm complete all as specified and directed

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or castaluminium alloy and fixed Length of bolt in 250 mm complete all as specified.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or castaluminium alloy and fixed Length of bolt in 250 mm complete all as specified.

S&F Aluminium handles, cast type, anodised Size of handle in 150mm complete all as specified and directed.

S&F Extruded aluminium alloy handles, fabricated type, anodised 125mm complete all as specified and directed.

S&F 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate including welding to steel frames.complete.

S&F Steel window/ventilator factory made, made out of mild steel box type and shutter suitable for double shutter i.e. Glazed and gauged shutter. Glazed shutter made out of hollow' section with sash bar and gauged shutter made out of hollow section without sash bar including hinges, tower bolt, handle, grill 10 mm sq bar including two coat of synthetic enamel paint over one coat of red oxide primer, tarred hold fasts, PCC bed blocks for fixing hold fast , including plain/figured glass and wire mesh complete all as per details shown in drawing No CEPZ/TD-245/01 sheet No 1/1 and CEPZ/TD-246/01 sheet No 1/2 & 2/2 including taking down existing spoiled and unserviceable windows/ventilators of any type ( wooden/steel) complete all as specified and directed

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with galvanised wire staples or using metal nut and bolts complete all as specified and directed.

S & F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or using metal nut,bolts, fixed with wooden/MS beads & screws etc complete all as specified

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified.

M&L for preparation of old wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified.

Dismanting of Asbestos cement (corrugated, semi corrugated , etc) sheets in roof coverings etc complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Dismantling timber scantling 40 Sq cm and over in section, in any position framed work.

M&L for Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. confirming to Fe-290 (Gde E?165)

M&L for prepration of New or previously untreated steel surfaces of any description, not other wise described over 10 cm width or girth and applying one coats of synthetic enamel paint over a coat of red oxide zinc chromate primer complete all as specified.

Demolition of brick work , built in cement mortar or cement lime mortar including all quions, arches, pillars, etc including demolition of precast rcc articles and disposal of debris out of MoD land complete all as specified and directed.

M&L for Brickwork with Fly Ash Bricks (old size), straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified.

M&L for brick work with sub class ‘B’ brick, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed..

M&L for brick work with sub class ‘B’ brick, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 complete all as specified and directed..

Taking down cement plaster of any description and thickness on walls/ceilings etc including racking out joints, hacking for key, scrubbing down with water etc including necessary scaffolding up to four storeys height of bldgs if required and removing of debris out of MoD land complete all as specified and as directed.

M&L for rendering 10mm thick in CM 1:6 on fair faces of brick work ,concrete surface of wall, finished surface even and fair without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on other than fair faces of brick work ,concrete surface of wall, finished surface even and fair without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on brick work ,concrete surface of wall, including mixing with liquid water proofing compound as per manufacturer instruction, finished surface even and fair without using extra cement complete all as specified and directed. Note:- WPC will be measured and paid separately

Supply only liquid water proofing compound all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying one coat of wall care putty on the surfaces & making the surface absolutely smooth surface and applying two coats of oil bound distemper finished without any brush marks on the surface complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash without any brush marks on the surface complete all as specified and as directed.

M&L for preparation of new plastered surfaces of Walls and applying two coat of Cement Base Paint, white or tinted over and including one coat of alkali resistant primer incl curing complete all as specified & directed.

M&L for Rendering 5mm thick on brick work or concrete surfaces in CM (1:3) in ceiling complete all as specified and as directed.

Demolition of Roofs, floors (other than ground floors), beams staircases, landing, cooking platform ,chajjas, & similar suspended work cement concrete is reinforced (reinforcement cut as required to facilitate demolition) and disposal of debris out of MoD land complete all as specified and directed. Note:- Demolition will be done only by mechanical cutter only .

M&L for RCC type B-1 (1:2:4) using 20 mm graded crushed stone aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like such as cover slab of septic tank/soak well etc complete all as specified and as directed. Note:- Reinforcement shall be measured and paid separately).

M&L for RCC type B-1 (1:2:4) using 20 mm graded crushed stone aggregate in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilaster and buttresses (Note:-TMT bars will be masured and paid sepretly)

Precast reinforced cement concrete, type B-1,1:2:4 (using 20mm graded crushed stone aggreagate)as in in landings, manhole cover set in cement mortor 1:6 , including neccessory form work complete all as specified and directed by Engr-in-Charge. (Note:-TMT bars will be masured and paid sepretly)

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter for fair finished surface

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon tal or sloping and similar work exc 10cm but n exc 20cm wide for fair finish surface

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200mm thick (Horizontal or sloping) Rough finished surfaces of concrete flat complete all as specified and as directed

M&L for Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality complete all as specified and as directed.

M&L for Mild steel TMT bars 6mm to 8mm dia ,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality complete all as specified and as directed.

Demolition of PCC (un-reinforced) in ground floors & pavings n.exc 15 CM thickness below or above ground level, complete all as specified and directed by Engr-in-Charge.

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.50 mm graded crushed stone aggregate as in flooring/sub base and surface finished rough all as specified and as directed.

Dismantling floor, hearth or wall tilling and terrazo topping incl cement mortar bedding ( but not backing) removing serviceable tiles to stores and rubish off the premises

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) in floor etc area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thk screed bed in CM 1:6 all as spd and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) in floor etc area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thk screed bed in CM 1:6 all as spd and directed.

M&L for glazed ceramic coloured in different colour combination as approved by GE ,450x300x7mm thick on vertical surfaces such as skirting, dados and riser to steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl rendering 10mm thick in CM (1:4) on brick or concrete surface complete all as spd & directed.

M&L for non abrasive paving (endura) tiles 300mm x 300mm x10mm thick (square/ rectangular) polished, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement over & including 15mm screed bed CM 1:4 to match complete al as specified and directed.Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

Surface excavation not exc 30 cm depth and averaging 15cm deep in foul condition for removing heaps of waste, cleaning of flora, fauma, follage and bushes around septic tanks,manholes and soak pits removing debris/ heaps of bushes etc from vicinity and depositing at a place where complete all as specified and as directed

Removal to excavated material (Soil) to a distance not exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge.

Removal to excavated material (Soil) to a distance exc 50m and not exc. 250m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge.

Returning filling in including spreading, levelling, watering and well remming in layers not exceeding 25cm thick in hard/dense soil complete all as specified.

M&L for hardcore of broken bricks of gauge exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed.

M&L for 100 mm thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in floor and finishing even and smooth without using extra cement complete all as specfied and directed.

M&L for 75 mm thick PCC (1:4:8) type D-2 using 40mm graded crushed stone aggregate as sub base, complete all as directed.

M&L for sand filling under floors or in foundations including watering and consolidation or layer of sand cushioning below interlocking paver block complete all as specified and as directed.

M&L for Coloured machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade rubber moulded glossy finish with grey cement and pigment complete all as secified and as directed. Note-Shapes of interlocking paver block shall be triangular/Zigzag/Haxagon/or other ,Colour of paver blocks (50% yellow and 50% Red) & laying pattern approved by GE.

M&L for Coloured machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 80 mm thickness, M-40 grade rubber moulded glossy finish with grey cement and pigment complete all as secified and as directed. Note-Shapes of interlocking paver block shall be triangular/Zigzag/Haxagon/or other ,Colour of paver blocks (50% yellow and 50% Red) & laying pattern approved by GE.

Demolition of existing roof treatment of any description such as worm out tarfelt, mortar of any description & any thickness, shrubs/roots ,vegetation, tree, terracing pcc/brick tiles, concrete bedding etc as directed and Cleaning of all foreign material debris etc by brushing and dusting, washing down with water etc ,surface shall be leveled with a layer of 20 mm thick screed bed in CM 1:4 including mixed with water proofing admixture as per manufacturer's instructions and applying roof treatment with 03mm thick APP modified membrane with non-woven polyster reinforcement(center core) with thermal insulation with white mineral gravel finish on upper side of weight not less than 3.5 kg/sqm , laid by torch application method with overlap 100 mm on length side and 100 mm on the width side as per manufacturer's instructions over one coat of approved cold applied bituminous oil based primer (IS-3384) @ 0.30 litre/sqm complete all as specified and directed. (Note:- WPC shall be measured and paid separately)

S&F in repair sink with drainage board made of stainless steel 1 mm thick with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of angle iron and connecting union to pipe over all size 915 mm x460 mm and bowl size 410mmx330mmx 160mm complete all as specified and directed.

S&F in repair Stainless steel plate in repair rack(Utensil Rack) of size (900mm x 750mmx250mm ) made out of AISl 304 stainless steel 0.63 mm thick sheet fixed with brass screw of required size including necessary fittings/nuts,bolts & washers complete all as specified and as directed.

M&L for 20mm thick Granite work black/rubby (pure black) in colour (table rubbed and polished) as in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl 15 mm thick screed bed in CM 1:4 incl cutting of 25 mm dia hole for gas pipe and incl rounding the edges complete all as specified and directed.

M&L for repairing to chajjas, roof projection and facias of exposed reinforcement surface or damaged loose RCC surface including cutting down rusted/exposed reinforcement and applying one coat of cement slurry and filling with cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) and finished with cement mortar 1:3 using coarse sand with mixing of liquid water proofing compound @2% by weight of cement or as per manufacturer instruction. Thickness of RCC member not exc 150 mm including scaffolding up to 8.0m height complete all as specified and as directed . Note : (i) No extra rates of scafffolding will be paid separately against this item. (ii) Water proofing compound will me measured and paid sepratly.

S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge and for every 01 RM length, provide 10 numbers stainless steel rings with 50 mm dia and proportionate for part there off, with stainless steel brackets near to ends with stainless steel finish for 25mm dia drapery rod at both ends. The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/windows. ( Including necessary fittings)

M&L for 18mm thick ultra voilet printed PVC board (weight not less than 12 Kg/Sqm) duly edge bonded with 0.8mm thick PVC taping as in shutters & shelf of Kitchen cabinet, cupboard, partition & almirahs etc fixed with screws to steel/timber frame work etc including taking down old shutters & shelf etc complete all as specified and directed.

S&F for Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, polished complete all as specified and directed

S&F hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws, Size of hasp and staple in mm 100 complete all as specified and directed.

S&F Continuous (piano) hinges 30mm Width of flaps (when open) ,mild steel, bright finish or electrogalvanised complete all as specified and directed

S&F in repair Gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed

S&F in repair for 15 mm bore chromium plated fancy type Bib taps, cast copper alloy with crutch or above butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repairs Viterous China wash basin, white, flat back, size 550x400mm excluding taps etc but including brackets,including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specfied and as directed.

S & F in repair 15mm bore dia fancy type long sank, chromium plated angular valves /stop valves, cast copper alloy, screwed down, high pressure ,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed (minimum weight 575 grams) complete all as specified and directed.

S&F in repair for 15mm bore Stop valves, fancy type, chromium plated with long shank and cup (concealed type),cast copper alloy, screwed down, high pressure, with crutch or above butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

S&F Rotational moulded polyethlene water storage tanks three layers of 500 ltrs capacity ISI marked (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part I including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including Dismantling of old brocken water tanks and refixing of inlet, outlet & over flow pipe etc complete all as specified and as directed.

S&F in repairs 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets ,fush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specfied and as directed.

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubing or conduit wiring, etc and making good, cutting not exceeding 10cm girth complete all as specified and directed

Taking up or down 15mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified and directed.

Taking up or down 20mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified and directed.

S&F 15mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling including taking down unserviceable tubing etc complete all all as specified.

S&F 20mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls, floor, ceiling including taking down unserviceable tubing etc complete all all as specified.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair Ball valves 20mm bore high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe & fixed. (min. weight 20mm-210 gms)

S&F in repair for vitreous China squatting pan, ‘Orissa’pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) squatting pan including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all as specified and directed.

S&F in repairs Swan neck CP Pillar taps fancy type 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe complete all as specified and directed.

S & F in repair brass chromium plated shower roses 75mm size with or without swivel joints including fixing to steel pipe or union complete all as specified and directed by Engr-in-charge.

S & F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S & F in repair corner glass shelf with bracket fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed.

S&F in repair Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern

Demolition and breaking up drain pipes (Salt glazed ware, PVC/AC or Reinforced concrete) set in cement mortar,and taking out of trenches, if required, Internal dia of pipe in 75mm/100mm complete all as specified and directed

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S&F in repair PVC (SWR) junction single, (single-T), equal or unequal of 110mm bore complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

S&F in repair 110mm dia PVC (SWR) bends complete all as specified & directed.

S&F 110mm dia PVC (SWR) bends complete all as specified & directed.

S&F in repair Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

S&F Grating doom 100 mm dia of PTMT (Minimum weight 25gms) complete all as specified & directed.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil.

Excavation over area not exceeding 1.5 m depth and getting out in any type of soil, complete all as specified and directed by Engr-in-Charge.

All as per item No 58 here-in-before but exceeding 1.5 m and not exceeding 3.00 m depth.

M&L for Cement concrete Type D-2 1:4:8 (using 40 mm graded crushed stone aggregate) in foundations, filling and mass-concrete complete all as specified and directed.

M&L for HDPE DWC pipe 200mm internal dia and external dia 230mm SN-04 confirming to SN-4 fixed with rubber seal and coupler required with and including suitable bends 90/60/45 degree etc single Y junction laid in tranches and jointed with cement solvent including testing complete all as specified and as directed by Engineer-in-Charge.

M&L for concrete bed to drain pipe in PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) including packing under and haunching against the sides of pipe after laid and tested for 200 mm bore pipe, complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:3:6 type C-2 (40mm graded crushed stone aggregate) in foundation and mass concrete complete all as specified

M&L for Cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and fair including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight and complete all as specified.

S&F 4mm dia galvanised steel wire, 150x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling, complete all as specified and as directed

Sch 'A' E/M work:- Taking down carefully copper or aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, sockets bulk, head fitting, tube light fitting by unscrewing carefully from boards etc and making good, distrubed surface of walls floors etc.

M&L for point wiring for one light/one fan controlled by one switch with 1.5 PVC insulated unsheathed multistrand copper conductor FRLS cable with and including PVC concealed conduit heavy duty 20 mm dia having thickness not less than 1.8 mm with all fittings including anodise pressed steel sunken box having thickness not less than 2mm with 3mm thick bakelite laminated sheet ISI marked for switches and sockets , including 1.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly, including cutting chiseling for concealed piping and making good disturbed surface to match with the existing surface complete all as specified and directed.

All as per Srl item No 125 here-in-before but for 5 pin 5 amps socket outlet on independent board complete all as specified and directed.

All as per Srl item No 125 here-in-before but for 5 pin 5 amps socket outlet on same board complete all as specified and directed.

All as per Srl item No 125 here-in-before but for call bell point complete all as specified and directed.

M&L for point wiring with 2.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable with in and including PVC concealed conduit heavy duty 20mm dia having thickness not less than 1.8 mm with all fittings including anodise pressed steel sunken box having thickness not less than 2mm with 3mm thick bakelite laminated sheet ISI marked suitable for 5 pin 15 amps socket outlet ,including 2.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface finishing the surface to match with the existingsurface complete all as specified and directed.

M&L for point wiring with 4 sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable with in and including PVC concealed conduit heavy duty 20mm dia having thickness not less than 1.8 mm with all fittings including anodise pressed steel sunken box having thickness not less than 2mm with 3mm thick bakelite laminated sheet ISI marked suitable for 5 pin 15 amps socket outlet ,including 4 sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface finishing the surface to match with the existingsurface complete all as specified and directed.

S&F switch piano flush button single pole one way 5 Amp 230 volts in existing circuit as directed buy Engr-in-charge.

S&F switch Bell push, flush type, 5 amp one way complete all as specified and directed by Engr-in-charge..

S & F switch piano flush type one way 15 amps SP 240 volts complete all as specified and directed.

S&F Socket outlet 2 in 1, 3 pin, 5A complete in existing circuit complete as directed buy Engr-in-charge.

S & F socket outlet 2 in 1, 5 pin, 5 and 15 amps flush type 230 volts complete all as specified and directed.

S & F lamp holder/batton holder/angle holder insulated body with bakelite back plate suitable for fittings complete all as specified and directed.

S&F ceiling rose 65 x 50mm three terminals complete all as specified and directed.

S&F ceiling fan regulator electronic socket type 5 stage speed variation ISI marked complete all as specified and directed.

S&F Buzzer Ding Dong, AC 230 Volts single Phase complete all as specified and directed by Engr-in-charge.

S&F sleek LED mirror light fitting 2 feet long 1x10 W including inbuilt drive, ballast , bipin holder, connector block etc. complete with all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 Sqmm 2 core complete all as required at site or directed.

S&F LED smart lamp, B-22 type, 12 watt complete all as required at site or directed.

S&F in replacement sleek LED Batten light fitting 1x22 W including inbuilt drive, having ballast , bipin holder, connector block etc. complete with all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 Sqmm 3 core complete all as required at site or directed.

S&F in repair LED Bulkhead fitting 10 watt with PDC aluminium housing and polycarbonate diffuser with IP-66 protection all as specified and directed by Engr-in-charge.

Taking down ceiling fan, by disconnecting electric connection, dismantling blades and removing fan from ceiling complete all as specified and as directed

Re-Hanging only ceiling fan (M.D. supply) and connecting up including provision of pvc insulated seathed copper cable 3 core 0.5sqmm from ceiling rose or connector to fan including minor repair such as replacement of locking pin, reel insulator, bolts, nut etc. including Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc.

M & L for providing/ cutting the round/ square hole of required size in wall finishing the distrubed surfaces as per existing finishes complete all as spd and supply and fixing MS AC ventilating fans, Single phase, 230 volts 225/230 mm or 9” H.D EX Fan (900 RPM)complete and supply and grouting the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core 1.5 sqmm copper cable from ceiling rose to exhaust fan motor and writting MES No. with black synthetic enamel paint 2.0 cm high complete all as spd and directed by Engr-in-charge.

M & L for providing/ cutting the round/ square hole of required size in wall finishing the distrubed surfaces as per existing finishes complete all as spd and supply and fixing MS ventilating fans Single phase, 230 volts 300 mm or 12” H.D EX Fan (900 RPM) complete and supply and grouting the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core 1.5 sqmm copper cable from ceiling rose to exhaust fan motor and writting MES No. with black synthetic enamel paint 2.0 cm high complete all as spd and directed by Engr-in-charge.

Supply, fixing, testing and connecting the service value 6.00 BEE 5 star rated ceiling fan 230 volts, single phase of 1200 mm sweep double bearing type, copper winding, Air delivery 210 including down rod, canopy cover Fan regulator etc and connecting with flexible copper conductor of 1.50 sq mm 3 CORE and including writing of MES No with black enamelled paint complete all as spd and directed.

S&F in replacement of sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 4 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases in wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed.

S&F in replacement of sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 8 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases in wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed.

S&F MCB SP 240 volts any rating from 6 to 40 amps, 'C' cruve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F MCB SPN 240 volts any rating 40 amps, 'C' cruve with rupturing capacity 10 KA, including providing thimble for out going cablescomplete all as specified and directed.

S&F MCB TPN, 415 volts any rating 40 amps, 'C' cruve with rupturing capacity 16 KA, including providing thimble for out going cablescomplete all as specified and directed.

S&F in repair sheet metal encloser with MCB DB single pole and neutral enclosure with a two pin and earth plug and socket 20 Amp 240 volt complete with one single pole MCB 20 Amp 'C' curve complete all as specified and directed

S&F in replacement sub Main Wiring with two PVC insulated unsheathed multistrand FRLS flexible copper conductor cable of size 2x6 sqmm and one PVC insulated multistrand unsheathed FRLS flexible copper conductor cable of size 6 sqmm (green colour) as earthing lead connecting to main earthing dolly drawn in and including non metallic PVC concealed conduit 20mm dia complete and making good to disturbed surface complete of wall/floor with cement mortar and finishes to match the existing surface complete all as specified and directed.(Note - Two runs of sub main wire, one run of earth wire and one run of PVC rigid conduit shall be measured as one running meter.)

Taking down single phase electric meter by disconnecting existing electric connection and re-fixing of the same electric meter at new location as directed by Engg-in-charge including connection with 6sqmm copper wires from DB to meter.

S&F bldg secuirty light fitting energy saving high efficiency LED street light fitting 35 Watts, 5700 K, IP 66, having pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, prismatic polycarbonate cover complete including GI bracket of size 25 mm dia bent to shape having length not less than 0.9 mtr fixing with clamp etc and making connections using cord flexible 3 core copper cable of size 23/ .0076 from ceilling rose/ PVC connector to light fittings or as directed by Engr-in-chrage.

M & L for earthing complete with galvanised steel earth plate electrode , 600 x600 x 6mm thick burried directly in the ground (earth pit not less than 2.25 mtr deep below ground level)with top edge of the plate not less than 1.5mtr below ground level connected to galvanised iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point , GI tubing 15 mm bore light grade protection pipe , GI watering pipe 20mm bore light grade with funnel and wire mesh , charcoal ,salt packed around the earth plate and precast PCC 1:2:4 (Nominal mix ) reinforced with XPM having weight not less than 4 kg /sqm including suitable handle of 6mm dia MS bar and angle iron 40x40x3mm frame for cover including earth work in any type of soil , removal of surplus soil to a distance n.exc 50m and connecting , testing on completion complete all as shown on electric plate No 03 of SSR -2009 Part I complete all as specified and directed.(Note: Excavation and earth work is deemed to be included in the rates quoted).

Supply, laying and testing in repair LT XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 16 sq. mm 4 core complete all as specified

Excavation in trenches, not exceeding 1.5 m wide and not exc 1.5 m in depth for laying of pipes/cable etc and not exceeding 10 sqm on plan for manholes etc and getting out in any type of soil, complete all as specified. and directed by Engr-in-Charge.

Sand cushioning with fine sand to under ground cables in trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable as specified in clause 19.75 of SSR Part-I complete all as specified and as directed by Engr-in-Charge. Note:-Punned thickness will be measured and paid

M&L for brick covering with width equal to length of brick as mechnical protection to cable with well burnt sub class 'B' bricks laid as directed.

Returning filling in including spreading, levelling, watering and well remming in layers not exceeding 25cm thick in hard/dense soil complete all as specified.

Removal to excavated material (Soil) to a distance not exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge.

M&L for GI tubing light grade 50mm bore for cable protection laid in tranches in road crossing or fixed to wall/pole including all fittings complete all as specified and as directed

Note:-The accepted amount will be arrived after deducting the Sch of credit i.e. Rs 30,333.00 and any other reduction if any from quoted amount.

JP AND CO. (BID ID -3143661)

GANDOTRA CONSTRUCTION CO (BID ID -3137476)

kay gee construction co (BID ID -3136687)