Repair / maint of HT Electric System HT Pole Stays ACSR conductors Chain links anti climbing devices GODs DO fuses and Overhauling of VCBs calibration of VCBs MCCBs prunning of trees Painting of poles LT Panels earthing for E/M installations und

Amount

Excavation in trenches not exc 1.5 meter wide and not exc. 1.5 mtr in depth for laying of under ground cable, pole foundation and stays etc and getting out in hard / dense soil etc complete all as specified and directed by Engineer-in-Charge

All as per item No 1 (here-in-before) but depth exc 1.5m depth and n'exc 3m wide.

Returning and filling in, including spreading and levelling, water and well remming in layers not exc. 25cm etc complete all as specified and directed by Engineer-in-Charge

Removing excavated soil to a distance not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point etc complete all as specified and directed by Engineer-in-Charge

Supply, laying, testing & commissioning of HT 11 KV (Earthed) XLPE insulated screened PVC bedded, electric power cable (heavy duty) with aluminium conductor 11000 volts grade,circular screened with extruded semi conducting compound in combination with copper tape , inner sheath of PVC tape galvanized steel strip flat , around and overall PVC sheathed, armoured conforming to IS 7098 Part II, 1985 amended upto date, of size 3 core 120 Sqmm, ISI marked, laid in trenches or passing through pipes/ducts including taking down old cable of any size etc complete all as specified and directed by Engineer-in-Charge.

Supply, laying, testing & commissioning of HT 11 KV (Earthed) XLPE insulated screened PVC bedded, electric power cable (heavy duty) with aluminium conductor 11000 volts grade, circular screened with extruded semi conducting compound in combination with copper tape , inner sheath of PVC tape galvanized steel strip flat, around and overall PVC sheathed, armoured conforming to IS 7098 Part II, 1985 amended upto date, of size 3 core 95 Sqmm, ISI marked, laid in trenches or passing through pipes/ducts including taking down old cable of any size etc complete all as specified and directed by Engineer-in-Charge. Note :- 1. Excavation and earthwork , sand cushioning , GI pipe, cable protection will be measured and paid for separately 2. Cable shall be tested at high voltage test before & after laying. 3. No straight through joint will be permitted inside pipe or duct. 4. Cost of straight through if any deemed to be included in cost of cable.

Supply & lay HDPE pipe 110mm bore for laying of HT cables etc complete with all accessores etc complete all as specified and directed by Engineer-in-Charge

S&F steel tubing GI light grade of size 80mm bore dia for cable protection passing under road / floor or for fixing to poles etc complete all as specified and directed by Engineer-in-Charge.

M&L for cable jointing kit for 11 KV grade cable for straight through heat shrinkable joint suitable for XLPE armoured aluminium conductor cable of size 3 core 50 to 95 Sqmm etc complete all as specified and directed by Engineer-in-Charge

All as per item No 09 (here-in-before) but 120-185 Sqmm 3 core

All as per item No 09 9here-in-before) but 240-400Sqmm 3 core

M&L for end termination cable jointing kit for 11 KV grade cable heat shrinkable joint, out door suitable for XLPE armoured aluminium conductor cable complete with jointing materials and accessories suitable for 3 core 50 to 95 Sqmm etc complete all as specified and directed by Engineer-in-Charge.

All as per item No 12 (here-in-before) but 120-185 Sqmm 3 core

All as per item No 12 (here-in-before) but 240-400Sqmm 3 core

M & L for checking of HT UG 11 KV XLPE faulty cable with HT UG cable fault locating testing machine, rectifing the fault, putting the jointing kit and charging the cable as all as specified and directed. Approx length 650 RM for each Job. (The rate for excavation, removing of old cable, laying after repairs is deemed to be included in the rate quoted by the contractor).

Dismantling of existing unserviceable HT / LT poles of any size and type from its position carefully and removing from the site and necessary excavation and earth work in any type of strata, demolition of concrete, disconnecting of conductoretc complete all as specified and directed by Engineer-in-Charge

Supply, erecting and fixing in true vertical position of steel tubular swaged pole, 11 mtr long complete with cast iron base plate, finial taper plug, bolt, nuts and screws as specified and of type 410 SP-31, conforming to relevant IS, including one primer coat of red oxide and two coats of aluminium paint and two coats of bituminous paint inside and outside of botton portion up to 1.8 mtr length all as specified and provide circular bend 1 No of width 2 cm complete all as specified and directed. (Excavation and earth work , foundation concrete and PCC coping shall be measured and paid separately)

M&L for cement concrete (1:4:8 ) type D2 using graded stone aggregate as in foundation for pole including necessary form work etc complete all as specified and directed by Engineer-in-Charge

Demolition of Pole coping and depositing where etc complete all as specified and directed by Engineer-in-Charge

M&L cement concrete (1:3:6 ) type C1 using graded stone aggregate as in foundation for pole including necessary form work etc complete all as specified and directed by Engineer-in-Charge

Dismantling of unserviceable existing cross arms made from channels, angles and unserviceable FI clamps, nuts, bolts etc from OH line and removing etc complete all as specified and directed by Engineer-in-Charge

M&L for cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, botls, washers, welding bending cold or hot, drilling holes for bolts, in any shape or size as indicated or irected and inclusive of one coat of red oxide primer, one under coat and one inishing coat of aluminium paint etc complete all as specified and directed by Engineer-in-Charge

Dismantling of unserviceable insulator of any type complete from its position and removing etc complete all as specified and directed by Engineer-in-Charge

M&L for pin type, porcelain, vitreous, brown or green insulator including one galvanised mild steel spindle, steel washers and one galvanised nut of size 150mm height, 150mm dia for 11000 volts grade etc complete all as specified and directed by Engineer-in-Charge

M& L for disc type, pocelien, vitreous, white or brown 145mm hieght, 255 mm dia ball and socket type complete with tension assembly clamps for conductor for 11000 volts grade single disc assembly etc complete all as specified and directed by Engineer-in-Charge

Supply & Fixing of Digital Voltmeter etc complete all as specified and directed by Engineer-in-Charge, Make: L&T, Seimens, couzerve

Dismantling carefully the existing unserviceable HT/LT overhead line ACSR fo any size from its position by necessary disconnecting of conductor and removing etc complete all as specified and directed by Engineer-in-Charge

Dismantling carefully the existing unserviceable HT/LT overhead line ACSR of any size from its position by necessary disconnecting of conductor and removing complete and supply and stringing ACSR (Weasel/ Ferret) for over head line securing on pole complete including binding wire, jointing sleeves aluminium tap and PG clamp etc of any size etc complete all as specified and directed by Engineer-in-Charge (Note :- (a)jumper on cutout point/2 pole structure/4 pole structure shall be provided with PVC insulated sleeve. (b) Rate is inclusive of jumper & tree branch cutting to make a safe distance from over head line.)

S&F in repairs/replacement of GI continuous earth wire 4mm dia on cross of poles for guarding including binding with aluminum wire 16 SWG etc. and dismantling of old broken guarding etc complete all as specified and directed by Engineer-in-Charge

M&L for restringing of HT over head line consisting of 3 conductors by dismantling, taking down, repairing wherever required including cutting, re-jointing andrestringing in situ, with proper sag, binding to insulator with and including aluminium binding wire etc complete all as specified and directed by Engineer-in-Charge

S&F jumpers in replacement made out of 6/1 x 2.59 mm weasel ACSR conductor in and including PVC alkaline pipe and nuts, bolts etc complete all as specified and directed by Engineer-in-Charge

S&F jumpers in replacement made out of 6/1 x 4.72mm DOG ACSR conductor in and including PVC alkaline pipe and nuts, bolts etc complete all as specified and directed by Engineer-in-Charge

Dismantling of unserviceable stay assembly carefully including stay wire, including M&L for necessary excavation and earth work in any type of soil, demolition of PCC of any type and removing from site etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement of galvanized MS stranded stay wire of size 7/4mm including necessary binding straightning etc complete all as specified and directed by Engineer-in-Charge

S & F in replacement of Loop type insulators ,vitreous porcelain, white , brown or green, large size with over all dimensions 140mm, clearance of hole 25.5mm including necessary cutting, jointing etc complete all as specified and directed by Engineer-in-Charge

S&F stay assembly complete with accessories as shown in Electrical Plate No 1 of SSR 2009 (Part I) using stay rod 20mm dia, including clamps made out of 50 x 6mm MS flat, MS galvansied stay plate 300mmx 300mm x 6mm and galvanised thimble including insulator 90x140mm all as specified and as directed. (loop type insulator, stay clamps, excavation and concrete shall be measured and paid separately

M & L for replacement of danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps of size 25x4mm, bolts and nuts of approved size, for HT, 25x20cm size etc complete all as specified and directed by Engineer-in-Charge

M&L for prunning and removing of tree branches touching to electric over head lines wild growth around LT /HT over head lines and around pole and stay complete to make clear span of 1.5 Mtr of tree both side of the OH line with JCB, Cutter and all tools, plants etc all as directed by Engineer-in-Chief Note : (i) Distance between pole to pole will be measured and paid. (ii) Any breakdown of line caused during punning shall be made good without any extra cost. (ii) Prunning of tree to be done twice a year (before & after rainy season) (iii) The contractor has to ensure the proper safety of the tradesmans to avoid any mishappening. If any mishappening occures the contractor will be solely responsible for it.

S&F in replcement of vertical type air break switch, gang operated, tripple pole, mechnically operated, outdoor type, with all fittings and accessories mounted on and including HT 11 KV porcelain insulators and steel channel frame, GI operating rod 25 mm dia of suitable length to worked from ground, including locking arrangements , suitable for 11000 volts, 400 Amps current rating complete including dismantling existing one all as specified and as directed.

Repair / Overhauling of air break switch by replacing stationary and moving contacts, flexible copper chord, GI nuts, bolts etc including alingment for smooth functioning from ground level all as required at site etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement of HT 11 KV out door non-linear type lightening arrestor with mountings, accessories complete fixed on cross arms of two pole structure / GI flat strip and connect with same size of ACSR conductor encashed in PVC alkathine pipe with all fittings connected to earth strip with nuts, bolts and washers, transmission class having discharge capacity of 65 KA and rupturing capacity 5 KVA and suitable for working pressure 9 KV RMS compelete including taking down old lightning arrestor all as specified and as directed including dismantling existing one etc complete all as specified and directed by Engineer-in-Charge

S&F drop out fuse unit, explusion type for out door air break gang oprated switch, single pole mounted on and including insulators for 11 KV working pressure fixed to and including MS channel with nuts, bolts and washer etc synthetic bounded fuse tube complete with line capcity suitable for current carrying capacity upto 100 Amps all as directed including taking down old one etc complete all as specified and directed by Engineer-in-Charge

Repairs / overhauling of drop out fuse 11 KV by replacing contacts, GI nuts, bolts etc all as required at site etc complete all as specified and directed by Engineer-in-Charge

M&L for renewal of earthing of poles/system with galvanised earth plate 60x60 cm x 6.30 mm thick electrode of size and 32 x 6mm GI strip buried vertically in ground not less than 2.25 mtr below ground level with top edge of the plate not less than 1.5 mtr below ground level and connected to copper strip dia by means of nuts, bolts and washers and encased in and including 15 dia GI medium grade pipe upt 2.4 mtr height form ground level fixed by MS flat iron clamp 40mm x 5mm with nut, bolt and washers, GI strip fixed to base along pole and connected to over head line for providing earthing to HT pole/feeder AB switch LA complete with charcoal dust, salt packed around plate 150 mm thick including watering GI pipe, medium grade 40 mm dia with blanking cap 1.5 mtr long fixed to funnel with wiremesh complete with PCC chamber and RCC chamber over all as per Electrical Plate No 5 of SSR Part I - 2009 incl excavation and earth work in any type of starta and testing on compeltion. (Note: Any length of GI strip and 15 mm dia GI medium grade pipe shall be provided as per actual requirement at site).

All as per item No 44 (here-in-before), but with copper plate 60x60cm x 3.15mm thick electrode and 20x3mm copper strip as earthing lead encased in 25 mm bore light grade GI pipe.

Supply and spreading in electrical outdoor installation yard, stone aggregate of size 20 mm at 11KV substations / Near DP structures after through cleaning, anti grass treatment etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in replacement of basic numerical relay,30v DC with facility over current,phase fault ,short circuit,earth fault,instantaneous witn connected accessories complete all as specified and directed. Make : CG/L & T/Ashida

Labour for Disconnecting,repairing,servicing and overhauling of existing HT 11 KV/33 KV VCBs/SF6 breakers of any make from housing and cleaning, rubbing and overhauling the mechanical parts and servicing of 11 KV indoor VCB, checking of quality of vaccum interrupter, insulation resistances, static contact resistance, testing (IR value, Ratio test, Polarity test) and connection verification of 11 KV current transformer (Set of three) by PRIMARY INJECTION KIT, and testing and calibration of relay (set of two over current and one earth fault) by SECONDARY INJECTION KIT including all other functional tests of VCB, C&R panel and CTs, PTs,auxilary relay complete all as directed. NOTE: (i) Rate Included also for complete bus bar cleaniong and tightning,checking of bus bar insulation test,IR test with heat shrinkasble bus bar slive,IR test ckeacking and replacement of rusted HT hardware nut and bolts (ii) Contractor shall make his own arrangement of testing equipments and electric supply so required. A detailed test report should be submitted to Engg-in-charge. (iii) Servicing of VCBs will be carried out by the authorised person of company.

Supply and fixing battery charger suitable for 30 Volt Dc/100 AH battery bank including for auto manual mode ,boost and float mode,manual mode step-for increasing voltage,mcb for outgoing convergen and one MCB for battery set current for DC charging upto 15 Amps coplete all specified and directed.Make: Powertech/Chhabi eletricals/Panava eletricales or equivalents as approved by GE.

S&F in replacement battery bank 30Volt output by using maintenance free batteries, industrial type, duly charged and tested for 30 volts constant output including M&L requried for modification in existing charging set for auto tripping arrangement to avoid over charging and to maintain 30 volt output continiously for tripping mechanism etc complete all as specified and directed by Engineer-in-Charge. Make : Amararaja batteries Ltd or equivalent as approved by GE

Supply and fix inreplacement of Dc Power pack ,input 230 Volt Ac and output 110 volt Dc,SPD base,,continous load 100 VA,impulse load 450 volt for 240 MS,back up 20 monute etc complete all as specified and directed by Engineer-in-Charge. Make Gogate Elerosystem /Allen Eletreicals or equivalent as approved by GE

Supplky and fixing CTTB( current transformer terminal block) 2. 5 Sqmm including control wiring 2.5 Sqmm etc complete all as specified and directed by Engineer-in-Charge

Supply and fix control fuses 10-32 Amps including HRC fuse link,base with carrier etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing PT fuses suitable for 11 KV,rating 3.15 Amps etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing Hooter suitable for control relay panel of range 18 -90 volt AC/DC etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing breaker control switch suitable for 15 Amps etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing multifunction meter etc complete all as specified and directed by Engineer-in-Charge

M & L for resin cast type twin secondary current transformer of ratio 200-100/5-5A ,core 1:15 VA/Class – .5 and core 2: 15 VA/class .3P10,STC : 26.3 KA/1 SEC for protection and metering , conform IS – 2705 of 1992 etc complete all as specified and directed by Engineer-in-Charge Make : Crompton/Kirloskar or equivalent in makes mentioned in list of makes in Appendix `C'

Supply and fixing toughend arylic transparent door glass with gas kit of suitable size existing size 5 mm

Supply and fix Auxilary contractor 2 No + 2 NC with Addon,30 volt DC,20-25 Amps etc complete all as specified and directed by Engineer-in-Charge

Supply and fixing Tripping/closing coil 11KV,30 volt Dc etc complete all as specified and directed by Engineer-in-Charge Make : crompton/kirloskar or equivalent as approved by GE

Supply and fixing Tripping/closing coil 33KV,30 volt Dc etc complete all as specified and directed by Engineer-in-Charge Make : crompton/kirloskar or equivalent as approved by GE

Supply only big Gear Assembly for VCB etc complete all as specified and directed by Engineer-in-Charge, Make - CG/Kirloskar or equivalent as approved by GE.

Supply only small gear assembly for VCB etc complete all as specified and directed by Engineer-in-Charge, Make - CG/Kirloskar or equivalent as approved by GE.

Supply and fix warm wheel for VCB etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix motor cut off limit switch etc complete all as specified and directed by Engineer-in-Charge,

Supply only micro switch etc complete all as specified and directed by Engineer-in-Charge, Make - CG/Kirloskar or equivalent as approved by GE.

Supply and fix Anti pumpiung relay etc complete all as specified and directed by Engineer-in-Charge,

Supply and fix timer for motor protection etc complete all as specified and directed by Engineer-in-Charge,

Supply and fix trip circuit healthy push butten with Normally open contact etc complete all as specified and directed by Engineer-in-Charge

Supply and fix Announaciator for SF6 control and relay panel upto 12 window voltage range 18-90 volt etc complete all as specified and directed by Engineer-in-Charge,

Supply and fixing spring charging indication/Tripping Indication with legend completye accessories etc complete all as specified and directed by Engineer-in-Charge,

M & L for SF6 copper Armed cable 10 core,2.5 Sqmm etc complete all as specified and directed by Engineer-in-Charge.

M&L for gas charging for breaker by using SF 6 gas including checking SF6 gas pipe line ,pole leakage and reparing and reffiling of gas etc complete all as specified and directed by Engineer-in-Charge,

Supply and fix in repair of racket wheel assembly for SF6 etc complete all as specified and directed by Engineer-in-Charge,

Supply and fix povel set assembly etc complete all as specified and directed by Engineer-in-Charge,

Supply and fix closing latch aseembly etc complete all as specified and directed by Engineer-in-Charge,

Supply and fix complete set oring assembly etc complete all as specified and directed by Engineer-in-Charge,

Supply and fix crank lever assembly etc complete all as specified and directed by Engineer-in-Charge,

Supply and fix AVR relay for RTCC panel etc complete all as specified and directed by Engineer-in-Charge,

Supply and fix tap position Indicator

Labour only for dehydration filtration and cleaning of transformer oil of 33 KV / 11KV power transformer / distribution transformer / HT switchgear till achievement of die-electric-strength of 56 KV for new insulating oil and 45 KV for existing oil at 2.5MM Gap all as specified and directed Note : Toping of Transformer oil shall be measured and paid separately.

Supply only new insulating oil conforming to IS 335 for Power Transformer/MOCB etc complete all as specified and directed by Engineer-in-Charge.

Decanning the Power transformer oil from leaking transformer by opening the stop valve.Checking for leakages, arresting the leakages, replacing cork sheet gasket 5 mm thick,bushing,washer, HV/LV Road,tapchanger gasket, reassembling the transformer completely at nearest authorized workshope & refilling transformer oil, connecting HT / LT connection complete and back install at sub station 33/11 solapur & New KLP etc complete all as specified and directed by Engineer-in-Charge. Note :(i) Spares required shall be measured and paid separately under relevant. (ii) Topping of transformer oil will be measured and paid separately. (iii) The rate quoted includes HV/LV rod,Gasket, cork sheet,washers,tap changer gaskit etc. (iv) The rates also includes charging with and without load. (v) The rates includes transportation of transformer to workshop and after repairing installed back at site complete all as directed by Engr-in-charge (vi) Re-insulation & heating of LV/HV coil included in rate quoted

Labour only for routine test of power transformer including pressure test,ratio test,IR test,magnetic core blance test ,open circuit test,vector group test,winding resistance test,no load test etc complete all as specified and directed by Engineer-in-Charge. Note : All test should be carried out through othorised company

M&L for overhauling existing 33 KV / 800A GOD set, horizontal operation by replacing all stationary and moving contacts for all the three phases, rutsed nuts, bolts etc complete all as specified and directed by Engineer-in-Charge.

M&L for repair and servicing testing and recommissioning series reactor by replacing gasket set, insulating oil etc including painting by using two coats of synthtic enemel paints etc complete all as specified and directed by Engineer-in-Charge.

M & L for servicing testing & overhouling of OLTC including opening top and bottom plate removing of oil and refiiling of oil and checking of all taps removing of uncv parts and replace it etc complete all as specified and directed by Engineer-in-Charge.

Supply only resistance moving contact aseembly for OLTC etc complete all as specified and directed by Engineer-in-Charge.

Supply only main moving contact assembly fro OLTC etc complete all as specified and directed by Engineer-in-Charge.

Supply only fixed contact for OLTC etc complete all as specified and directed by Engineer-in-Charge.

Supply only transister register assembly etc complete all as specified and directed by Engineer-in-Charge.

Supply only local remote switch etc complete all as specified and directed by Engineer-in-Charge.

Supply only eletrical counter etc complete all as specified and directed by Engineer-in-Charge.

Supply only oil Sealed etc complete all as specified and directed by Engineer-in-Charge.

Supply only top let gasket & bottem let gasket assembly etc complete all as specified and directed by Engineer-in-Charge.

Supply only OLTC door glass with comlpete assembly etc complete all as specified and directed by Engineer-in-Charge.

Supply only starter, Three phase 4-10 AMps etc complete all as specified and directed by Engineer-in-Charge.

S&F in replacement HT fuse element 10C-OX type 11KV, 10 Amp, single phase etc complete all as specified and directed by Engineer-in-Charge. Make : Anand / Eswani / Electric / Siemens or equivalent as approved by GE.

Supply only spring charging motor gear box assembly 230 VAC, for VCB etc complete all as specified and directed by Engineer-in-Charge. Make - , Crompton/ABB/Siemens or equivalent as approved by GE

Supply only control fuse links NS type 2A, 4A, 6A,10A,16A etc complete all as specified and directed by Engineer-in-Charge.

Supply only busbar support insulator etc complete all as specified and directed by Engineer-in-Charge.

S&F dropout (DO) fuse, explosion for outdoor, single pole mounted on and including 33000V insulator - 02 Nos and MS Channel with nuts, bolts and washer of capacity 100Amp etc complete all as specified and directed by Engineer-in-Charge.

S&F lightning arrestor, station class, metal oxide 33 KV class III IEC long duration, current impulse rating with pressure relief high suitable for 33 KV including reconnecting in 33 KV distribution circuit and testing etc complete all as specified and directed by Engineer-in-Charge.

S&F 33 KV bus bar made out of 40mm dia 3mm thick aluminium tube including painting with insulated paint of RYB for colour coading etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing terminal box including TB terminal for CT/PT connection for 33 KV VCB including complete wiring and testing etc complete all as specified and directed by Engineer-in-Charge.

M & L for replacement of Pin type, porcelain, vitreous, white,brown or green insulator including one galvanised mild steel spindle,two galvanised iron washers and one galvanised iron nut, 100mm height, 65mm dia for 1100 volts grade etc complete all as specified and directed by Engineer-in-Charge.

M & L for replacement of shackle Type, Porcelain, vitreous, white, brown or green insulator including galvanised mild steel straps, washers,insulator bolts, washers and nuts, 100mm height and 115mm dia including two nos of galvanised steel strap of size 31x5mm fitted with 14mm dia bolts and nuts etc complete all as specified and directed by Engineer-in-Charge.

M&L for painting to 33 KV substation outer fencing and 11 KV substation fencing of structure complete including channel, beams, angle bracket supports, clamps by using two coats of aluminium paint after scrapping out existing wornt out paint including square wire mesh etc complete all as specified and directed by Engineer-in-Charge.

M & L for painting of HT steel tubular pole 11 mtr long in two coats of aluminium paint and one coat of red oxide as primer including writing of pole nos etc complete all as specified and directed by Engineer-in-Charge.

M & L for replacement of danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps of size 25x4mm, bolts and nuts of approved size, for HT, 25x20cm size etc complete all as specified and directed by Engineer-in-Charge.

Supply , install, testing and commissioning 11 KV power factor capacitor type PMPO 70 KVAR rated KV 6.7 single phase 50 Hz non PCB type insulation level 28/75 KVRMS/KVP, UF value cap bank current rating 10.44 Amps including mounting arrangement suitable for 11000 volt etc complete all as specified and directed by Engineer-in-Charge.

S& F in replacement sign boards for MES installations of size 1200x 900mm made out with angle iron 40x40x 6mm as framing covered both side with 2 mm thick aluminium sheet rivetting on frame covered with retro reflective sheet & 100mm high letters as diredcted. Th sign board to be fixed on 2 No. 40x40x6mm angle iron legs embedded in PCC(1:4:8) using 40mm graded stone aggregate including necesary excavation complete at the installation etc complete all as specified and directed by Engineer-in-charge

Supply & Fixing of Digital volt meter etc complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing of Digital Ammeter etc complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing in replacement of 33 KV, 400 Amps, Air Break Switch isolator, GOD with complete fitting and accessories mounted on and including 33 KV insulator and steel channel frame, GI operating rod of existing size and suitable length to work from ground, including locking arrangement and dismantling existing one etc complete all as specified and directed by Engineer-in-charge

Supply & Fixing HT cable route indicator of cast iron not less than 100 mm dia fixed through welding angle irom support of size 35 mm x 35mm x 5mm thick, 50cm long including two coats od synthetic enamel paint over a coat of red oxide primer embededin a PCC block of size 60cm x 30cm x 10 cm (PCC 1:3:6) type C1 using graded stone aggregates. The whole assembly of PCC iron will be planted in ground upto 30cm etc complete all as specified and directed by Engineer-in-Charge.

An amount of Rs 97,792.00 shall be deducted from BOQ on account of schedule of credit

Paragon Electrotechnics

Maruti Abhiyantriki

BHAVIN INFRA