REPAIR TO PROTECTIVE WORK, HARD STANDING, DRAIN, PATH, MS RAILING, FENCING PERIODICAL, OTHER MISC B/R WORKS AT DAGSHAI AND CERTAIN REPAIRS TO PIPE LINE WORKS AT SOLAN UNDER GE KASAULI

Amount

Schedule 'A' Section - I

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

Demolition stone slabs of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in position not otherwise specifically provided for complete all as specified and as directed.

Demolition of brick or stone masonary built in cement mortar including all quoins arches pillars etc but excluding ashlars facing dressed stone work and precast concrete block, complete all as specified.

Demolition of Concrete of any description and in any position not otherwise specifically provided for all as specified and as directed.

Taking down cement plaster on brick or stone wall, Ceilling etc including racking out joints, hacking for key scrubbing down with water etc to receive new plaster etc.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc 1.50 sqm each .

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm but n.exe 4.0 Sqm each .

Taking down shutter of any description exe 1 Sq.m but n.exe 2.0 Sqm each.

Taking up or down waste and vent pipes of any type and any dia complete.

M&L for brick work with sub class `B` bricks, in straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

M&L for brick work with sub class `B` bricks, in straight or curved on plan in any radius , built in CM 1:4 complete all as specified and directed.

M & L Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth without using extra cement all as specified.

M & L Rendering 15mm thick on other than fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement all as specified.

M&L for cement concrete 1:2:4 type B-1 ( using 20mm graded stone aggregate) as in hard standing including necessary form work and finishing surface even and fair without using extra cement complete all as specified and directed.

M&L Non skid ceramic coloured tiles 7mm to 8mm thick (squre/rectangular) area of each tile exc0.11sqm but not exc 0.18 sqm in floors , set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed with cement mortar 1:6 complete all as specified.

Material and labour for Glazed ceramic coloured tiles in vertical surfaces exc 0.08sqm and n exc 0.16sqm, 7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match with and including 10mm thick backing coat on vertical surfaces of wall in cement mortar 1:4 complete all as specified and as directed.

M&L for 16 to 18 mm thick granite stone machine cut (table rubbed & polished) in one piece as in steps,jambs,pillars,windows cills,cooking platform and similar work bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigments to match the shade of granite stone including grinding and polishing including making hole in platform and screed bed for bedding 20 mm thick in cement mortar 1:6 ,complete all as specified.

S&F in repair stop valve 15 mm cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for union etc complete all as specified.

S&F in repair stop valve 20 mm cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for union etc complete all as specified.

S&F in repair 15mm bore Bib taps, chromium plated cast copper alloy, fancy type, screwed down for iron pipe or for brass ferrule etc complete all as specified and directed.

Ditto as item No 21.00 above but long body.

S&F in repair 15mm bore angle cock, chromium plated, brass, fancy type, screwed both ends for iron pipe or for union etc complete all as specified and directed.

S&F in repairs Vitreous China wash hand basin white with pedastal flat back size 550x400 mm including brackets, complete all as specified

S &F in repair for plastic water closet seat cover white closed pattern with flat bottom mild steel chromium plated or aluminium hinging device etc complee all as specified and directed.

S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts,) complete incl making good to floor to match with adjoining surfaces all as directed by Engr-in-Charge.

S&F as in repair fixing WC Orissa pattern of size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) includung provision of lime concrete bedding etc complete all as specified and directed by Engr-in-Charge

S&F in repair 10 ltr capacity PVC valveless syphonic action type flusing cistern low level white with inlet ball valve float and handle including bracket fixed etc complete all as specified.

S&F in repair PVC connection 15mm bore with PTMTnuts of length 450mm etc complete all as specified.

S&F in repair 32mm dia PVC flexible waste pipe for urinals/WHB/sink all as specified.

S&F in repair Towel rail 600mm long chromium plated fixed in and including chromium plated brass screws and wooden/plastic cleatsetc complete all as specified.

S&F in repair 75 mm dia PVC(SWR) floor trap, with grating including jointing with solvent cement etc complete all as specified.

S&F in repair 110 mm dia PVC(SWR) 'S' trap including jointing with solvent cement etc complete all as specified.

Material and labour for precast RCC (1:2:4) type B-1 using 20mm graded mechanically crushed stone aggregate as in landing cover slab for kittchen platform manholes , septic tank set in cement mortor ( 1:6) including necessary form work complete all as specified and as directed. (Reinforcement shall be measured separately).

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including crancking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.5mm dia or securing with clips quality confirming to deformed or twisted bars complete all as specified and as directed.

S & F in repair 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, walls complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair PVC(SWR) bend 110mm dia bore complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC(SWR) bend 110mm dia bore with access door complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC(SWR) junction single(Single T) equal or unequal 110mm dia bore with access door complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC(SWR) vent cowl110mm dia bore complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC(SWR) bend 75mm dia bore complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC(SWR) bend 75mm dia bore with access door complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC(SWR) junction single (Single T) equal or unequal 75 mm dia bore with access door complete all as specified and directed by Engr-in-Charge.

S & F 35 mm thick factory made, 2nd class hard wood, plain framed, paneled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides, the size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated etc complete, all as specified .

S & F 35 mm thick 2nd class hard wood glazed and skelton shutter open rebated and prepared to receive glass ,gauge etc ( without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc size of members of shutters as specified in SSR Part-I, section 8 clause 8.24(a), supplied and fitted to chowkats.

M&L 2nd class hardwood as in plain, solid straight chowkats and frames wrought framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and as directed.

S & F Soild PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC prelaminated sheet and edges will be painted to match wilth prelaminted sheet reinforced with MS square tube supplied and fixing in opening as per specification & drawings.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) of prelamintaed wood grain printed PVC sheet on both sides and stiles and rails feathered at edges and consisting of frame made out of M.S. tubes for top & bottom rails.M.S. frame shall be covered with heat moulded PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 100 mm long stainless steel butt hinges all as specified and directed.

S & F for Aluminium anodized 150 mm long barrel tower bolt of extruded section and fixed.

S&F 150mm long extruded aluminium alloy anodized handles febricated type.

S&F 250 mm long Aluminium alloy anodised sliding door bolt with hasp and staple(bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolt of extruded section or cast aluminium alloy and fixed etc complete.

M & L for 500 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including PTMT float valve of 15 mm dia and taking down old unserviceble PVC water tank all as specified in SSR Part-I completed and as directed by the Engr-in-Charge.

S&F CP grating of 100 mm da including jointing with solvent cement all as specified and as directed.

M&L for cement concrete 1:2:4 type B-1 ( using 20mm graded stone aggregate) as in hard standing including necessary form work and finishing surface even and fair without using extra cement complete all as specified and directed.

M&L for Preparation of newly plastered surfaces of walls and applying two coat of oil bound distempering over a coat of Chalk whitening etc complete all as specified.

M&L for preparation of new plastered surfaces of wall including cornices, pillasters etc of bldgs and applying two coat of cement base paint on walls over a coat of primer complete all as specified and directed.

M&L for preparation of new plastered / unplastered surfaces of wall including cornices, pillasters etc of bldgs and applying tthreecoat of white wash complete all as specified and directed.

M&L preparation of new / old plastered or unplastered surfaces of walls including complete removal of existing treatment by washing, rubbing down and stopping of previously treated surfaces and applying two coat of exterior emulsion paint over a coat of primer of approved tint and make complete all as specified and directed.

M&L for preparation of plastered or unplastered old surfaces of walls and applying one coat of oil bound distemper of any approved tint complete all as specified and directed.

All as per item No 64.00 above but complete removal of existing treatment and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M&L preparation of old painted steel surfaces exc 10cm in width or girth and appling one coat of synthetic enamel paint complete all as specified and directed.

M&L for for applying 1 mm thick wall care putty of old decorated plastered or unplastered surfaces of wall complete all as specified and directed.

M & L for preparation of old painted wooden surfaces of any description position and location not otherwise described over 10cms width or girth and applying one coat of synthetic enamel paint (ordinary tint) all as specified and as directed.

All as per item No 68.00 above but applying two coat of synthetic enamel paint complete all as specified and directed.

M & L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4 as in road side parapet / Drain all as specified and as directed.

All as per item No 70.00 but except stone complete all as specified and directed.

M&L cement concrete in surface channels and drain type C-1 1:3:6 (20mm aggregate) complete all as specified and directed.

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement, including forms moulds, mitred/stopped ends etc complete all as specified and directed.

M&L for PCC Type B1 1: 2:4 (20 mm graded stone aggregate )Providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges as in coping ,kneelers , appex stone, coping etc.

M&L for cement concrete 1:4:8 type D2 (using 40mm graded aggregate) in sub base of floor and foundation filling & mass concrete including necesarry formwork and finishing surface fair and even all as specified and diected.

M&L for screed bed or bedding layer of mortar 20mm thick CM 1:6 for laying tiles and stone slab complete all as specified and directed.

M&L for Chequered cement concrete tiles30cm x 30cm x 25mm thick set, jointed and pointed in neat cement slury in floors with grey cement and pigment in floors with grey cement and pigments complete all as specified and directed.

M&L for Chequered cement concrete tiles30cm x 30cm x 25mm thick set, jointed and pointed in neat cement slury in floors with grey cement and no pigment in floors with grey cement and no pigments complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded.

S&F Mild steel work for Chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 all as specified and as directed.

M&L for preparation of new steel surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified & directed complete all as specified and directed by Engr-in-Charge.

S&L for sheet glass ordinary quality 3.00 mm thick in aluminium windows of area of each pane exc 0.50 Sqm complete all as specificed and directed by Engr-in-Charge.

M & L for two coats of synthetic enamel paint over coat of pink primer on new wooden surfaces of any description not otherwise described over 10 Cm width or girth including preparation of surfaces complete all as specified and as directed by the Engineer-in-Charge

Removing building materials etc. (other than spoil payable under items 03028 to 03031 in Section-3—Earthwork) to a distance of 100m or beyond the lead up to 2 km included in the rates, including loading, unloading and stacking at the destination all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and disposing off the rubbish materials where complete all as specified and directed

M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and no pigment set and jointed in neat cement slurry all as specified.all as specified and as directed

M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and pigment set and jointed in neat cement slurry all as specified.all as specified and as directed

Excavation in trenches in hard dense soil n.exc 1.5 mtr wide & n.exc 1.5mtr in depth and n. exc. 10sqm on plan for laying pipe in trenches and getting out complete all as specified and directed.

Returning filling in trenches, spreading, levelling, watering and well ramming in layers n.exc 25cm in hard dense soil complete all as specified and directed.

Removing of surplus soil to a distance n.exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above starting point complete all as specified and directed.

Taking out unserviceable/defective/damaged/blockage GI/MS pipe 15 mm bore steel water tubing,sorting out serviceable pipe fitting for reuse and cleaning the pipe including fitting and removing away all unserviceable pipe from site, complete all as specified and as directed. (Note: Exacavation and earhwork shall be measured and paid for separately).

All as per serial item No. 91.00 here-in-before but of size 20mm bore -ditto-.

All as per serial item No. 91.00 here-in-before but of size 25 mm bore -ditto-.

All as per serial item No. 91.00 here-in-before but of size 40mm bore -ditto-.

All as per serial item No. 91.00 here-in-before but of size 50mm bore -ditto-.

All as per serial item No. 91.00 here-in-before but of size 80mm bore -ditto-.

All as per serial item No.91.00 here-in-before but of size 100mm bore -ditto-.

All as per serial item No. 91.00 here-in-before but of size 150mm bore -ditto-.

S&F steel water tubing medium grade, ISI Marked conforming to IS 1239 Part-I 2004, 15mm bore with and including all fittings such as bends , elbows,tees, short length , socket, union, check nuts, nipples and weldings etc. fixed and laid in trenches/floor/under culvert/road crossing etc including testing complete all as specified and as directed.

All as per serial item No. 99.00 here-in-before but of size 20mm bore -ditto-.

All as per serial item No. 99.00 here-in-before but of size 25mm bore -ditto-.

All as per serial item No. 99.00 here-in-before but of size 40mm bore -ditto-.

All as per serial item No. 99.00 here-in-before but of size 50mm bore -ditto-.

All as per serial item No. 99.00 here-in-before but of size 80mm bore -ditto-.

All as per serial item No. 99.00 here-in-before but of size 100mm bore -ditto-.

All as per serial item No. 99.00 here-in-before but of size 150mm bore -ditto-.

S&F in replacement of Bronze gate valve for 15mm bore pipe, with iron wheel head, screwed both ends for iron pipe and fixed, ISI marked conforming to IS 778: 1984, fixed as in repair complete all as specified and directed.

All as per serial item No. 107.00 here-in-before but of size 20mm bore -ditto-.

All as per serial item No. 107.00 here-in-before but of size 25mm bore -ditto-.

All as per serial item No. 107.00 here-in-before but of size 40mm bore -ditto-.

All as per serial item No. 107.00 here-in-before but of size 50mm bore -ditto-.

Taking out old unsv and Supplying, fixing and testing of cast steel Sluice valve PN1.6 as per IS-14846, body, dome, wedge-CI IS:210, rings-bronze IS:318, Spindal-SS IS:6603, Gland Paking greasy jute packing, fasteners-CS, Gasket- Natural rubber, nominal size DN-150 mm, both ends flanged in existing line, after removal of old unserviceable sluice valve without damaging to existing pipe line complete all as specified and directed by Engr-in-charge. Note : Suitable size flanges for existing pipe line, Joints and jointing materials shall be included under this item.

All as per serial item No. 112.00 here-in-before but nominal size DN-100 mm -ditto-.

All as per serial item No. 112.00 here-in-before but nominal size DN-80 mm -ditto-.

S&F Cast iron Non Return valve W/O by pass arangement , Swing type, of Size 100 mm bore, confirming to IS 5312, flanged ends with nuts bolts, washers complete including taking down of old one .

S&F Cast iron Non Return valve W/O by pass arangement , Swing type, of Size 150 mm bore, confirming to IS 5312, flanged ends with nuts bolts, washers complete including taking down of old one .

Supply and fix Cast Iron Air Release Valves with two air Outlets, conforming to IS 14845 of size 100 mm dia bore and fixing up in Cast Iron Water supply mains of size 100 mm dia.

Supply and fix Cast Iron Air Release Valves with two air Outlets, conforming to IS 14845 of size 150 mm dia bore and fixing up in Cast Iron Water supply mains of size 150 mm dia.

Construction of brick masonary pit of size 60 x 60 x 60cm internal size with MS sheet 3mm thick and angle iron frame of size 40x40x6mm duly painted with 2 coats of synthetic enamel paint over a coat of red oxide primer including locking arrangement, lifting handle and including excavation / earth work, PCC in foundation, brick work, plaster including demolition of existing pit complete all as specified and shown in drawing No. STD- 1258, sheet 1/1. (original date - 30.11.93 and revised date - 15.09.2000 ) Note : Drawing mentioned above has not been enclosed herewith, however the same can be seen in the office of GE Kasauli.

Construction of brick masonary pit of size 90 x 90 x 90 cm internal size with MS sheet 3mm thick and angle iron frame of size 40x40x6mm duly painted with 2 coats of synthetic enamel paint over a coat of red oxide primer including locking arrangement, lifting handle and including excavation / earth work, PCC in foundation, brick work, plaster including demolition of existing pit complete all as specified and shown in drawing No. STD- 1258, sheet 1/1 (original date - 30.11.93 and revised date - 15.09.2000 ) Note : Drawing mentioned above has not been enclosed herewith, however the same can be seen in the office of GE Kasauli.

Construction of brick masonary pit of size 120 x 120 x 120 cm internal size with MS sheet 3 mm thick and angle iron frame of size 40x40x6mm duly painted with 2 coats of synthetic enamel paint over a coat of red oxide primer including locking arrangement, lifting handle and including excavation / earth work, PCC in foundation, brick work, plaster including demolition of existing pit complete all as specified and shown in drawing No. STD- 1258, sheet 1/1 (original date - 30.11.93 and revised date -15.09.2000). Note : Drawing mentioned above has not been enclosed herewith, however the same can be seen in the office of GE Kasauli.

S&F in replacement of Water meter 100 mm nominal bore conforming to IS:2373-1981 having CI casing bronze body and SS/Alloy/Bronze gear having dial duly marked with litres or kilolitres in boldface, thread/flanged end type with provision of strainer out side the meter complete all as specified and as directed .

Supply of calcium hypo chloride, 65%-70% chlorine content, high strength granular disinfectant for treatment of drinking water complete all as specified and qty as per requirement and as directed by Engr-in-Charge.

S&F in replacement of Foot Valve conforming to IS-4038 flanged ISI marked completed with nut, bolts, washers etc including taking out old existing u/s foot valve of 100 mm dia.

Amount of credit of Rs. 113956.00 for retrived old material as mentioned in Schedule 'A' section-II of tender document in pdf form, will be deducted offline while acceptence of tender.

Rajesh Agencies