DEMOLITION AND RECONSTRUCTION OF CERTAIN SMQs UNDER GE AF AMLA

Blank

Blank

Blank

Blank

Blank

Blank

Blank

Blank

Blank

SCH 'A' PART XI (MISC B/R & E/M ITEMS) Note:- Excavation and earthwork to the extent required for execution of relevant item under this schedule unless otherwise specified shall be measured and paid under relevant items of Schedule 'A' Part-II.

INTERNAL WATER SUPPLY

Supply and fixing angle valve of cast copper alloy chromium plated fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed 15 mm bore (concealed) complete all as specified and directed.

Supply and fixing 15mm dia Two Way Bib taps, fancy type,,cast copper alloy chromium plated with crutch or butterfly handle, screwed down for CPVC pipe or for brass ferrule and fixed complete all as specified and as directed.

INTERNAL ELECTRIFICATION

Supply and fixing LED Lamp 9 watt 220 volts AC of suitable size complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and Fixing LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.complete all as specified and as directed.

Supply and fixing LED Building Security light fitting 25 watt complete all as specified and directed by Engr -in- charge.

Supply and fixing MCCB 63 Amps 4P 25 KA 415 Volt Make Indoasian Cat No 830020 including MCCB Enclosure for 63 Amp MCCB Make Indoasian Cat No 811985 fixed on wooden board of appropriate size for mounting of enclosure complete all as specified and as directed. NOTE:-Rate inclusive of Fixing of cable including lugging complete

Supply and Fixing ceiling fan 230V, 50 Hz AC, 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) complete with hanging arrangement by down rod alongwith steel wire rope for additional safety in ceiling fan with all allied accessories and connecting up with three core, 0.75 sqmm PVC insulated copper conductor cable complete all as specified and directed.

Supply and Fixing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm (for Toilets) complete all as specified and as directed.

Supply and Fixing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m (for Kitchen) complete all as specified and as directed.

Supply and Fixing electric water heater, storage type steel body and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessoriessuch as safety valve, thermostate, NRV, connection piece etc. complete all as specified and as directed.

Supply and fixing Smart RF/Cellular Single Phase AC Meter Tamper Proof, Static Meter of Class 1.0, 315 V, 50 Hz, 10 A-60 A conforming to IS-16444 and relevant IEC standards with inbuilt Radio Frequency communication facility with self healing mesh network with default and on demand display, billing data generation facility, anti-tamper features, Microprocessor and LED/LCD based circuitry including Polycarbonate Meter Box of minimum suitable size for 1 Phase meter with viewing glass, concealed hinge and earth bolt plugged complete all as specified and directed. Meter Should support sending the following data : 15/30 min instantaneous data for voltage, current, power factor, power, cumulative energy and frequency, monthly billing survey for Cumulative Energy and Max Demand to software Meter should have connect / disconnect functionality operable from mdm/billing software and prepaid features would be MDM / Billing end as per prevalent IS including taking down of existing meter and deposit to MES store yard for safe custody all as specified and as directed . Note:- Contractor has to ensure integration and maintainance of meters with the existing Advance Metering infrastructure (AMI) of smart meters of different makes without any additional infrastructure and cost implication.

EXTERNAL WATER SUPPLY

Supply, install, connecting, testing and commissioning openwell submersible mono set pump, with suitable suction / delivery head of 20 meters and discharge of 350 LPM, CI impeller coupled with three phase induction motor 415 Volt, 2800 RPM with capacity 3.7 KW/ 5.0 HP, including base frame for pump with foundation and connected with inlet as well as delivery pipe with standard arrangement as per manufacturer specification motor, pump, base complete including including accessories complete all as specified and directed.

LIGHTENING PROTECTION

Supply & fixing PVC junction box IP 65 of size 200 mm x 160 mm x 98 mm having shutter & lifting knob with provision of earthing strip entry glands on wall/poles with suitable size of nut, bolts and washers complete all as specified and directed.

Supply and fixing post insulator epoxy LV type suitable for lightening conductor aluminum strip size 25x4 mm, fixed on wall/roof/pole including screws complete all as specified and directed.

EXTERNAL ELECTRIC SUPPLY

Supply, install, testing and commissioning APFC panel outdoor type of capacity 20 KVAR, factory made of suitable size, dust & vermin proof, double door, fabricated out of powder coated MS CRCA sheet 3.15 mm thick and mounted on 70 cm long legs of angle iron of size 50 mm x 50 mm x 6 mm out of which 30 cm shall be embedded in foundation of PCC 1 :2 :4 type B-1, using 20 mm graded stone aggregate and provided with lugs of suitable size and cable glands for incoming/out going connections complete all as specified. The panel shall be suitable for and including housing the following main parts in addition to any other part recommended by the panel manufacturer. Note: Drawing for APFC Panel shall be got approved by GE before fabrication. (i) TPN MCB 63 Amps, 25 KA - 01 No. (for incoming) (ii) MCB TP 16-32 Amps - 05 No. (iii) Heavy duty power capacitor 20 KVAR (3x5 KVAR + 1x3 KVAR +1x2 KVAR) dry type with discharge device resistor conforming to IS 13340- 01 No. (vi) Phase indicating lamps LED type RYB. (v) Panel mounted multi function energy meter for measuring Voltage (0-500 Volts), Current (0-200 Amps), frequency and power factor including resin dia cast CT of CT ratio 100/5 - 01 No. (vi) Bus bar chamber with 4 Nos aluminium strip of 200 amps rating and fixed on epoxy insulation complete with colour coding.

Material & labour for erection in true vertical position and fixing of steel tubular poles, swaged, welded complete with CI base plate 6mm thick of size 300mm x 300mm, final taper plug pole cap, bolt and nuts and screw as per IS-2713 (Pt-II) made out of ERW MS tubing with including drilling of hole of required size on bottom and top of pole including painting with two coat of aluminium paint over one coat of primer for exposed surface and two coat of bituminous paint for embedded portion in concrete complete of type 410 SP-31 (9 mtr long) complete all as specified and directed. Note: (a) The rate includes staying the poles in a truly vertical position till the foundations are properly set. (b) Excavation, foundation concrete, presenative treatment, etc. will be measured separately under the appropriate sections. (c) Painting to steel tubular poles (inside and outside) is however included in the rates of steel tubular poles.

Supply and fixing LED street light fitting 70 Watt, 230 Volts AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specifed and directed.

(aa) Provn of safety guarding equipments such as 02 Nos Pit switches controller guarding pit pulley, guarding pit ladders, facia plate to cover free space between car cabin and hoist way & switches. (ab) Provn of “Press and speak” system to be connected with lift existing intercom exchange compatible with exchange. (ac) DO's & Don'ts chart to be installed inside the car cabin. (ad) Evacuation process chart to be installed inside the car cabin. Incase when lift stuck in midway shaft. The letters/Numbers in chart should be luminous radium coloured to see in all day/night time.

FIRE FIGHTNING

Supply and fix swinging hose reel drum with gun metal nozzle and 20mm bore rubber hose 30 meter length, wall mounted with 180° swing, specifications as per IS-884: latest revision made of high quality mild steel, powder coated in red colour, hub width approx 230 mm, rubber hose with maximum operating pressure 10 bar, flow rate 22.5 lpm at 7 bar pressure complete all as specified and directed.

Supply and fix CI dual plate wafer type check valve with nitrile/EPDM seat, SS shaft & springs in PN 2.0, 100 mm bore tested to pressure of 15 Kg/ Sqcm complete set complete all as specified and directed.

Supply & fixing cast iron double orifice kinetic air valve as per IS:14845, PN 1.0 flanged end 100 mm dia bore and fixing up in water supply mains complete all as specified and directed.

Supply and fixing light weight squeeze grip type CO2 type fire extinguishers of 3 kgs capacity with stand from branch new seamless dran controller of explosives approval fitted with wheel valve as per IS:3224 with ISI mark with discharge hose and horn and supplied with initial charge as per IS:15683 with ISI mark (Sub Stn & pump house)

Supply and fixing of dry powder ABC stored pressure squeeze grip type fire extinguishers, 9 kg capacity, IS:15683:2006, filled with ABC mono ammonium phosphate base power-90 complete with discharge hose and wall mouting bracker, 2 mm mild steel EPDM rubber, pressure gauge which work effectively on all class of fires (ABC & E) with 5 years warranty incl transportation all taxes and all labour charges etc complete.

Supply and fixing 10 Ltrs round buttom sand/water buckets along with round bottom type, enamel painted white inside and red outside and letter fire in black outside & handle with mounting bracket along with suitable size MS stand to install the buckets as per the local fire standards.

Supply, install, testing and commissioning of booster pumps for 440 Volts, 3 Phase, 50 Hz confirming to IS-12469 : 1988 With CI Casing bronze impeller and stainless steel shaft mounted on heavy duty bearings suitable for 30 meter head and 450 LPM discharge complete all as specified and directed.

DIESEL ENGINE GENERATING SET

Lumpsum price worked out by the contractor for “AREA DRAINAGE” as listed in Schedule ‘A' Part XII representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part XII on Srl Page No. 60

(a) Engine : Diesel engine 1500 RPM of 25.5 BHP or as recommended by manufacturer, water cooled, conform to IS-10000, overload capacity of 10% for one hour in every 12 hours of continuous run, 12 volts electric battery start, complete with fly wheel and torsional vibration damper, radiator and all standard fittings/fixtures as per standard manufacturing practices and battery charging ammeter and fuses, and also including self starter (12V) battery charging alternator complete.

(b) Alternator : AC alternator, brushless, 415 V AC 50 Hz, 3 phase, 4 wire type, rated for continuous output of 25 KVA at PF 0.8, 1500 RPM, insulation class 'H' enclosure SPDP (IP 23), self excited & self regulated with AVR for +1% voltage regulation, conform to IS-4722, overload capacity of 10% for one hour in every 12 hours of continuous run, coupled directly/ suitably to and to match the above engine.

(c) Enclosure : Provision of an integral type, approved/certified acoustic enclosure as per CPCB-IV complaint, for the DG set to restrict the noise level to 75 dbA at one metre and ensure that temperature rise within the canopy shall not exceed 5-7 degree celsius, shall be made of 16 SWG CRCA MS sheet with powder-coated finish on outside and provided with non igniting fire retardant foam as acoustic material. There shall be four hinged doors out of which one shall be with glass window and base frame shall be of ISMC.

Supply, installation, testing & commissioning LT Panel made out of CRCA sheet 3.15 mm thick outdoor type CPRI approved, totally enclosed with front and rear opening, hinged doors with projected an raised platform of suitable size weather and water proof with necessary locking arrangements along with lugs, cable glands of various sizes for cables, danger notice plate, strickering of switch gear about termination of switch gear, and the nuts/ bolts etc used are to be made of rust proof material incl as per IS: 613 (2000) copper bus bar with insulators suitable for three phase and four wire LT AC, 50 Hz 415 V 320 A capacity complete with powder coating, necessary internal electric connection as required and provision of the following: (Main Panel) Incoming: (a) MCCB 4 Pole, 415 V, 36 kA (ICS=ICU=ICW for 1 Sec), with magnetic release capacity 200 Amps, with adjustable type overload protection, short circuit protection - 01 No OUTGOING : (b) MCCB 3 Pole, 415 V,16 kA (ICS=ICU=ICW for 1 Sec), with thermal release of capacity 63 Amps, with fixed type overload & short circuit protection - 01 No for DG Panel (c) MCCB 3 Pole, 415 V,16 kA (ICS=ICU=ICW for 1 Sec), with thermal release of capacity 100 Amps, with fixed type overload & short circuit protection - 02 Nos. for Building (d) MCB TPN, 415 V,10 kA, 'C' Curve of capacity 63 Amps - 01 No for APFC Panel (e) Intelligent Panel meter to measure voltage, current, frequency, power factor etc with all connected CTs of each breakers (f) LED Indicating Lamps for each phase with colour code Red Yellow Blue for R, Y and B Phases for each breakers

civil works for making good the disturbed surface during installation. (iii) The DG Set should comply with all the latest CPCB-IV + Norms. (vi) The capacity of DG set shall be net after all derating factors as per relevant IS design.

Supply, install, testing and commissioning of cubical type CPRI approved dust and vermin proof factory made LT panel board indoor type front opening (double shutter) with locking arrangement of suitable size made out of 2.00 mm thick CRCA sheet (IS 8623) with 50mm x 50mm x 6mm angle iron frame duly painted with two coats of powder coated paint over a coat of red oxide primer on outer surfaces and epoxy paint on inner surfaces, protection class IP-56, grouted on floor. The LT panel board shall be suitable for operating on AC 415 volts, 3 phase, 50Hz, 4 wire system with suitable of PVC copper conductor for internal wiring, thimbles gland, cable lugs,nuts, bolts, washers, etc. including PCC foundation (PCC 1:2:4 type B-1) of suitable size as per panel board 0.5 Mtr above ground level grouting and bottom portion of enclosure shall be minimum 30 cm above ground level of legs of angle iron supply & comprising of the following including internal pre-wiring complete all as specified and directed by Engr-in-Charge:-

NOTE: The contractor will submit from OEM detailed specification/design parameters, construction drawing of all components of lifts as per IS-14665 and as per latest amendment for approval of GE before execution of work such as:- (a) Type of Lifts : Passenger (b) No. of Passengers & Load capacity : 13 Nos & 884 Kg (c) Speed : 1.0 mtr/sec with single speed motor (d) Power Supply : 415 volts, 3 phase AC, 50 Hz (e) Type of Drive : AC variable voltage & variable frequency drive. (f) Type of Machine : Gearless permanent magnet & directly coupled horizontal traction machine. (g) Car size (Inside) : As per IS-14665 (Part-1) 2000 (h) Car and landing door at all floors : Automatic centre opening with VVVF, sliding type door fabricated by stainless steel sheet not less than 1.5 mm having hair line finish. (j) Car enclosure :Manufactured with stainless steel frame not less than 1.5 mm with Hair line finish having stainless steel false ceiling with hair line finish, Internal lighting arrangement with PIR sensor automatic operation LED light fittings on automatically in human presence within 05 mtr range complete internal ventilation system provided with concealed aerial flow/cross flow fan with auto cut off system and stainless steel grill wire mesh for protection, looking mirror and hand rails as per OEM design.

Material and Labour for providing earthing with galvanized steel earth plate electrode of size 60cmx60cmx6mm thick bured directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanized earth lead by means of bolts, nuts check nuts and washers of galvaniz

SEWAGE DISPOSAL

Supply, laying in trenches and jointing of 200 mm dia bore double wall corrugated polyethelene (HDPE) pipe of stiffness class designation SN8 including all necessary jointing material and fittings such as couplers, connectors,bends, elbows ,Tees and end caps etc complete all as specified and as directed.

Blank

Blank

Blank

Blank

GENERAL SUMMARY

Total amount of Schedule 'A' Part XIII carried over to General Summary

Lumpsum price worked out by the contractor for “BUILDINGS & STRUCTURES” as listed in Schedule ‘A' Part I representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part I on Srl Page No. 31

Lumpsum price worked out by the contractor for “EXCAVATION,EARTHWORK & SITE CLEARANCE (FOR SCHEDULES OTHER THAN SCHEDULE 'A' PART-I)” as listed in Schedule ‘A' Part II representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part II on Srl Page No.33

Total amount of SCHEDULE 'A' PART XIII (MISC ITEMS) (B/R & E/M ITEMS) brought forwarded from Serial Page No. 77

Lumpsum price worked out by the contractor for “INTERNAL WATER SUPPLY” as listed in Schedule ‘A' Part IV representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part IV on Srl Page No. 37

Lumpsum price worked out by the contractor for “DEMOLITION & DISMANTLING” as listed in Schedule ‘A' Part III representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part III on Srl Page No. 35

Lumpsum price worked out by the contractor for “INTERNAL ELECTRIFICATION ” as listed in Schedule ‘A' Part V representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part V on Srl Page No. 42

Lumpsum price worked out by the contractor for “LIGHTENING PROTECTION” as listed in Schedule ‘A' Part VII representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part VII on Srl Page No. 46

Lumpsum price worked out by the contractor for “ROAD/ PATH/ CULVERT” as listed in Schedule ‘A' Part VIII representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part VIII on Srl Page No. 50

Lumpsum price worked out by the contractor for “EXTERNAL WATER SUPPLY” as listed in Schedule ‘A' Part IX representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part IX on Srl Page No. 53

Lumpsum price worked out by the contractor for “EXTERNAL ELECTRIFICATION” as listed in Schedule ‘A' Part X above/below the lumpsum price as inserted by MES for Schedule ‘A’ Part X on Srl Page No. 56

Lumpsum price worked out by the contractor for “SEWAGE DISPOSAL ” as listed in Schedule ‘A' Part XI above/below the lumpsum price as inserted by MES for Schedule ‘A’ Part XI on Srl Page No. 58

Lumpsum price worked out by the contractor for “FIRE FIGHTING” as listed in Schedule ‘A' Part VI representing above / below the lumpsum price as inserted by MES for Schedule ‘A’ Part VI on Srl Page No. 44