Construction of Swarn Jayanti Environment Training Institute at Manesar in Gurugram District

Amount

A) CIVIL WORK Earth work excavation in ordinary soil exclusive of compensation of earth- Kassi work undressed involving an average horizontal throwupto 2 metres, and an average vertical lift upto 0.5 metre including breaking of clods.When over all lead is upto 60mtr. (HSR 6.2 a) upto depth of 20 cm top soil

Earth work in excavation in foundations, trenches etc. in all kinds of soil, not exceeding 2 meters depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 Mtrs. (HSR 6.6)

Earth filling under floors with surplus soil excavated from foundation and taken only from outside the building plinth, in 15 cm layers including ramming watering and consolidating lead upto 30 meters. (HSR 6.13)(a)

Centring and shuttering for flat surfaces such as suspended floors, roofs, landings, chhajjas, shelves etc. Inclination not exceeding 25 degree with horizontal (HSR 9.1) A) Basement

First storey

Second storey

Third storey

Fourth storey/mumty & machine room

Centring and shuttering for faces of walls, Partitions, retaining walls, well steining and the like (vertical or battering) including attached pilasters, buttresses etc. (HSR. 9.5) A) Basement

First storey

Second storey

Third storey

Fourth storey/mumty & machine room

Centring and shuttering for sides and soffits of beams haunchings, girders, bressumers and lintels (HSR 9.7) A) Basement

First storey

Second storey

Third storey

Fourth storey/mumty & machine room

Centring and shuutering for columns (square or rectangular or polygonal in plan) (HSR 9.9) A) Basement

First storey

Second storey

Third storey

Fourth storey/mumty & machine room

Centring and Shuttering for coulmns (circular or curved in plan ) (HSR 9.10) A) Third storey

Centring and Shuttering for corbel, parapets, fascias and other similar items, including edges (HSR 9.11) A) First storey

Second storey

Third storey

Fourth storey/mumty & machine room

Shuttering for faces of concrete foundation and foundation beams (vertical or battering) (HSR 9.13)

Cement concrete 1:8:16 with stone aggregate 40 mm nominal size in foundation and plinth (HSR 10.28)

Cement concrete 1:4:8 with stone aggregate 20 mm nominal size in foundation and plinth (HSR 10.38)

Cement concrete 1; 2 ; 4 with stone aggregate 20 mm nominal size in foundation and plinth.(HSR 10.41)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size in first storey upto 4 metres above plinth level (HSR 10.59)

Providing & laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, inmprove workability without impiring strength and durablity as per direction of Engineer-in-charge in foundation and plinth. (Note: cement content considered in this item is @ 330 kg/cum) (HSR 10.66)

Providing & laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but exclluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability withoute impairing strength and durability as per direction of Engineer-in-charge in first storey upto 4 meters above plinth level. (Note: cement content considered in this item is @ 330 kg./cum) (HSR 10.73) A) First storey

Second storey

Third storey

Fourth storey/mumty & machine room

Pre-cast cement concrete 1:11/2:3 with stone aggregate 20mm nominal size in Kerbs and the like items, finished smooth with 6mm thick cement plaster 1:3 on exposed surface including form work, placing and fixing in position, complete as per (HSR 10.77 + 10.95a)

Pre-cast factory manufactured cement concrete 1:11/2:3 with stone aggregate 20mm nominal size in tiles & channels and the like items, finished smooth with 6mm thick cement plaster 1:3 on exposed surface including form work, placing and fixing in position, complete as per (HSR 10.78 + 10.95a)

Cement concrete 1:11/2:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centering and shuttering, laid in position, complete in all respects. (HSR 10.82+10.95(a)

Damp proof course 25 mm thick of cement concrete 1:2:4 using stone aggregate (HSR 10.115) -Note

Providing and laying 80 mm thick ISI Marked interlocking paver blocks conforming to is 15658 : 2006/ IRC SP 63-2004 of all shapes and colours in design mix cement M-40 over a bed of 30 mm thick fine sand complete in all respect. (HSR 10.159) Note : Reputed make Paver Block Only ISI marked will be used as approved by Engineer-in-charge.

First class brick work laid in cement sand mortar 1:6 in foundation and plinth (HSR 11.2)

First class brick work laid in cement sand mortar 1:4 in foundation and plinth (HSR 11.4)

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 meters above plinth level (HSR 11.7) A) First storey

Second storey

Third storey

Fourth storey/mumty & machine room

First class brick work laid in cement sand mortar 1:4 in first storey upto 4 metres above plinth level (HSR 11.9)

11.43 cm thick brick wall laid in cement sand mortar 1:4 without reinforcement, in foundation and plinth. (HSR 11.47)

11.43 cm thick brick wall laid in cement sand mortar 1:4 in superstructure (HSR 11.48)(a) A) First storey

Second storey

Third storey

Fourth storey/mumty & machine room

Providing & laying Autoclaved Aerated (cellular) concrete light weight blocks (As per IS: 2185, part 3) masonary in non load bearing walls using blocks of size 625mm X 250mm X 200m with cement sand morter 1:6 in superstructure complete in all respect.(HSR 11.105.) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material A) Basement

First storey

Second storey

Third storey

Fourth storey/mumty & machine room

Top khurra 0.6 m x 0.6 m for rain water pipe in 25 mm thick cement concrete 1:2:4 ovr 50 mm thick cement concrete 1:8:16 (HSR 13.50) A) First storey

Second storey

Third storey

Fourth storey/mumty & machine room

Supplying & fixing in position G.I pipe class 'B' spouts in chajjas and cantilevers. (HSR 13.55 (e) 50mm i/d G.I. pipe Second storey

Bottom khurra on ground 1.2 m x 0.6 m consisting on brick-on-edge laid in cement mortar 1:3 over 75 mm cement concrete 1:8:16 including 12 mm thick cement plaster 1:3 (HSR 13.57) A) First storey

Second storey

Third storey

Cement concrete 1:2:4 gola 10 cm x 10 cm quadrant along junction of roof with parapet wall finished smooth, where specially specified (HSR 13.64) A) First storey

Second storey

Third storey

Fourth storey/mumty & machine room

Providing & fixing PVC rainwater pipe 6 kg. pressure of ISI mark in cement mortar during masonary work (a) 100 mm dia PVC pipe 6 kg pressure (Note:- Reputed make PVC pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge (HSR. 13.89) (a). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material A)Fourth storey/mumty & machine room

Providing & fixing PVC rainwater pipe 6 kg. pressure of ISI mark in cement mortar during masonary work (b) 150 mm dia PVC pipe 6 kg pressure (Note:- Reputed make PVC pipe such as Supreme, Finolex, Prince will be used as approved by Engineer-in-charge (HSR. 13.89) (b). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material A) First storey

Second storey

Third storey

Providing and fixing PVC bend ISI mark (a) 100 mm dia PVC bend (Note:- Reputed make PVC bend such as Supreme, Finolex, prince will be used as approved by Engineer-in-charge. (HSR 13.90)(a) Note The Agency to whom the work ia alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing and fixing PVC bend ISI mark (b) 150 mm dia PVC bend (Note:- Reputed make PVC bend such as Supreme, Finolex, prince will be used as approved by Engineer-in-charge. (HSR 13.90)(b) Note The Agency to whom the work ia alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Provding and fixing False ceiling with grooves with 12 mm to 15 mm thick 600mm x 600 mm best quality mineral fibre tiles of approved make fixed on MS Steel runners frame i/c cost of screws angles, cleats, rawel plugs, with taping and painting etc. complete in all respects as approved by the Engineer-in-charge (HSR 13.93) A) Ground floor

First floor

Second floor

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the samemanner. (DSR 12.55) A) First storey

Second storey

Third storey

Fourth storey/mumty & machine room

Screed of 50 mm thick cement concrete 1:8:16 to be laid below the topping (HSR 14.4) A) Basement

Ground floor

First floor

Second floor

Third floor/mumty & machine room

Precast chequered terrazzo tiles 20 mm thickness in ordinary grey cement without chips laid on 20 mm thick bed of cement coarse sand mortar 1:3 with neat cement slurry between joints and over the base in floors, treads of steps and landings. (Note:- Reputed make Tile only ISI marked will be used as approved by Engineer-in-charge). (HSR 14.45) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material. A)Basement

Ground floor

Kotah stone flooring minimum 25 mm thick in any pattern as specified over 12 mm thick base of cement coarse sand mortar 1:3 ladi and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing (HSR 14.62) note: The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material A) Basement

First floor

Third floor/mumty & machine room

Kotah stone 20 mm thick in skirting risers of steps, dados and wall facing (lining ) and pillars laid on 12 mm thick cement coarse sand plaster 1:3 ladi and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing including labour for fixing cramps, dowels and pin etc. (HSR 14.66) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material A) Basement

First floor

Third floor/mumty & machine room

Providing and fixing rectified ceramic tiles/ anti skid tiles of size 400x400mm of approved make in floors laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT BELL, JOHNSON, RAK & SIMPOLO (HSR 14.91) A) Ground floor

First floor

Second floor

Providing & Fixing Ist Quality ceramic glazed wall tiles conforming to IS. 15622 ( thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry including ointing in white cement mixed with pigment of matching shades complete. (b) size of ceramic glazed tiles 300 x 450 mm of reputed manufacturer like:- RAK, N"ITCO, Kajaria, SIMPOLO & ORIENT BELL shall be used as approved by Engineer-in-charge (HSR 14.92) (b) Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material A) Ground floor

First floor

Second floor

Laying and fixing Granite stone in all shades 15mm to 18mm thick in skirting/dado, risers of steps, pillars and wall facing, laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of granite including labour for fixing cramps pins and dowels etc. (Excluding the cost of granite stone). (HSR 14.95) granite shall be supplied by the Deptt. A) Basement

Ground floor

First floor

Second floor

Third floor/mumty & machine room

Laying and fixing Granite stone in all shades 15 mm to 18 mm thick in flooring, laid in any pattern as specified over base of 20 mm thick cement coarsed sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of granite stone comp. in all respect. (Excluding the cost of granite stone). (HSR 14.96) granite shall be supplied by the Deptt. A) Basement

Ground floor

First floor

Second floor

Third floor/mumty & machine room

Providing edge moulding to 17-20 mm thick grenite stone counters, vanities etc. including machine polished to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge (Moulding) (HSR 14.98 new) (ii) Double moulding A) Basement

Ground floor

First floor

Second floor

Plastering on walls 10 mm thick cement plaster 1:3 (HSR 15.2) A) First storey

Second storey

Third storey

Fourth storey/mumty & machine room

Plastering on walls 12 mm thick cement plaster 1:4 (HSR 15.5) External Plaster A) Basement

First storey

Second storey

Third storey

Fourth storey/mumty & machine room

Plastering on wall 12 mm thick cement plaster 1:6 (HSR 15.7) A) Basement

First storey

Second storey

Third storey

Fourth storey/mumty & machine room

Plastering on wall 15 mm thick cement plaster 1:6 on the rough side of single or half brick wall 1:6 (HSR 15.12) Internal Plaster A) Basement

First storey

Second storey

Third storey

Fourth storey/mumty & machine room

10 mm thick cement plaster 1:4 under side of ceiling (HSR 15.52) A) Basement

Ground floor

First Floor

Second floor

Third floor/mumty & machine room

Preparation of ply wood surface for painting including sand paparing the surface and applying filling with approved quality filler consisting of with lead, linseed oil, varnish and chalk miti including finishing the surface to required finish complete. Painting on wooden surfaces etc. (HSR 16.1) Through Rate

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. (Note:- First quality paint of reputed make firm such as goodlass- Neolac, Berger, Garware, Jenson, Nicholson, Asian & shalimar shall be used as approved by Engineer-in-charge in writing, drum of paint shall be opened in presence of Engineer-in-charge. (HSR 16.3) Through Rate

Applying priming coat with metal primer on new steel or iron work including preparation of surface, painting on mettalic surfaces etc. (Note:- First quality paint/primer of reputed make firm such as goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & shalimar shall be used as approved by Engineer-in-charge in writing, drum of paint shall be opened in presence of Engineer-in-charge) (HSR 16.9) Through Rate

Painting two coats excuding priming coat with ready mixed paint for metelic surfaces in all shades on new steel or iron work (Note:- First quality paint of reuted make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, drum of paint shall be opened in presence of Engineer-in-charge) (HSR 16.17) Through Rate

Providing and Applying Painting two coats with ready-mixed exterior paint in all shades on newly plastered or concrete surface of walls. (Note:- First quality paint of reputed make firm such as Goodlass-nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge) (HSR 16.26 Through Rate

Finishing walls with exterior decorative cement based paints such as snowcem Robbiacem etc on new work, two coats to give an even shade (HSR 16.61) Through Rate

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (Note:- Reputed make putty such as JK/Birla shall be used as approved by Engineer-in-charge). (HSR 16.81) Through Rate

Providing and fixing medium density fibre board (MDF) interior grade in plain lining but jointing including wooden plugs (hard wood), placed at 45 cm to 60 cm, complete with necessary nails (frame work shall be payable extra) (b) 19 mm thick (HSR 17.48 (b)) A) First storey

Third storey

Providing & fixing six-levers brass 10 cm mortice latch and lock, and a pair of lever handles with necessary screws, etc. complete (Indian make of reputed firm, such as godraj or equivalent) (HSR 17.73)

Supplying and fixing hydraulic door closer, ISI mark, with necessary screws, etc. complete (HSR 17.82) (C.) ISI designation no. III size of door 851 mm to 1000 mm)

Providing & fixing 0.50 mm thick aluminium sheet including cost of necessary screws etc. complete (HSR 17.87)

Factory manufactured panelled door or glazed window, shutters of commercial hard wood, such as hollock, champ, chikrassy & chaplash etc. (Non-coniferous timber other than teak, conforming to IS specification no. 1003, Kiln-seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm ide other rails and 100 mm wide other rails with panels of 15 mm thick tongued and grooved of commercial hrd wood and including costof iron hinges, screws, chocks, cleats, stops, nails etc. complete fixed in position (Excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) -(b)- 35 mm thick (HSR 17.90) (b)-Note I under 17.18.

Factory manufactured wire gauze door and window shutters of commercial hard wood, such as hollock, champ, chikrassy & chaplash etc. (Non-coniferous timber other than teak, conforming to IS specification no. 1003, Kiln-seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chocks, cleats, stops, nails etc. complete fixed in position (Excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) -(i)- 30 mm thick (HSR 17.92) (1)-Note I under 17.18.

Factory manufactured solid flush door shutters, with block board core as per I.S. No. 1659-1669 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part-I and II, fixed in position, including iron hinges, screws chocks/cleats and stops etc. (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position):- (Note) :- Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges. (Duro, Green) 25 mm. thick (HSR 17.93 (a) (i)- note I under 17.18))

Factory manufactured solid flush door shutters with block board core as per I.S no. 1659-1669 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S 2202 part-I anf II fixed in position, including iron hinges, screws, chocks/cleats, and stops etc. (Excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) -(Note) : - Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminatyed core and lipped edges. (Duro, green) 35 mm thick (HSR 17.93) (a) (iii))-Note I under 17.18.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required neoprene felt etc. aluminium sections shall be smooth, rust free straight mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/paneling C.P brass / stainless steel screws, all complete (HSR 17.95)+ note (i) Add Rs. 15/- per kg. extra if powder coating of 50 micron is done instead of anodizing in above item no. 9 & 10.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS 733 and IS : 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom, and sides with required neoprene felt etc. Aluminium sections shall be smooth, rust free straight mitred and jointed mechanically wherever required including cleat angle. Aluminium snap beading for glazing/paneling C.P brass/stainless steel screws, etc. complete. Shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of PVC/neoprene gasket required including aluminium fitting (HSR 17.96) + note (i) Add Rs. 15/- per kg. extra if powder coating of 50 micron is done instead of anodizing in above item no. 9 & 10.

Providing and fixing 12 mm thick preleminated paticle board flat pressed three layer or graded wood particle board conforming to IS:12823 grade I type II in paneling fixed in aluminium doors. Windows shutters and partition frames with C.P brass / stainless steel screw etc. complete (HSR 17.97 (b)) Pre-laminated particle board with decorative lamination on both sides.

P & F double glazing consisting of glass 6mm (toughened) & annealed plain glass i/c 12mm air gap i/c cost of structural silicon sealant & weather sealant (DC795/DC789) & double sided acrylic foam tape in structural glazing works upto 4th storey. The outer glass shall have U value < 1.8 solar factor < 0.35 Light transmission > 49% of make Blue essence EH 46/35 Ecosense essence AIS or equivalent as per approval (HSR 17.104)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS 6315 marked for door including cost of cutting floors as required embedding in floors and cover plates with brass pivot and single piece M.S sheet outer box. (HSR 17.99 (a)) with stainless steel cover plate.

Providing aluminium jali of thickness 7 mm thick with opening-75mm x 75 mm of including anodizing and fixing in frame with cost of screws etc. complete (HSR 17.100)

Providing and fixing aluminium round shaped handle of outer dia 100 mm with screw etc. Complete. (I) Anodized (AC-15) Aluminium. (HSR 17.102 (i))

Wrought iron and mild steel (using angles, flats, square bars, tees and channels), ladders, grills gratting frames, window guards, iron doors openable or fixed staircase or parapet or any other type of railing, gates and tress guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position (HSR 18.12)

Steel reinforcement TMT bars FE-500 EQR/FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including straightening, bending, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights /depths/storeys/basements etc. NOTE:- Reinforcement shall be measured in length including hocks, if any, separately for different diameters as actually used in work, excluding overlaps, Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. (HSR 18.22)

Supplying and fixing glass panes including special metal sash putty of approved make (b) glass panes 4 mm thick exceeding 40 sq.m areas. Modi, Saintgobain (HSR 18.30 B)

Pressed steel sheet frames (Chowkhats) consisting of 2 mm thick steel sheet of the specified section including ironlugs (hold fasts) iron hinges, conforming to PWD specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts and finished with one coat of ready mixed paint red lead non-setting primer of approved quality fixed in position including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:3:6 for lugs complete. (a) Door and window frame of size 89 mm x 50 mm with 40 mm wide single rebate (Item no. 18.34)(a) A) First storey

Door and window frame of size 127 mm x 50 mm with 40 mm wide double rebate (HSR 18.34) (c)

Preparation of Sub Grade including trenching, rough dressing of soil, final dressing of earth to given levels and camber, watering rolling with road roller, and compacting the bed.(HSR 24.1)

DSR Items Providing and fixing 50 mm thick extruded polystyrene rigid insulation board of required size underdeck on ceiling surface, complying with ISO 4898:2008 & ASTM C 578-08b - type VI, having thermal conductivity of 0.0289 W/m K as per ASTM C 578 (measured as per IS 3346), compressive strength of > 350 kPa listed as per ASTM D 1621, density of 34-36 kg/cum as per ASTM D 1622, waterabsorptions < 1% by volume as per ASTM D 2842, oxygen index of 24.1 to 28.1 listed as per ASTM D 2863, cell size 0.4 mm of dia(max) as per ASTM D 3576. Fire retardent property as per DIN 4102,Part 1 of class B2 and as per ASTM E84 class A, fixed with suitablewater based adhesive and fastener, complete in all respect as per the direction of Engineer-in-Charge.(DSR 26.8)

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. 13.85.1 With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre sqm (DSR 13.85.1)

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. 13.85.3 With water thinnable cement primer on wall surface havingVOC content less than 50 grams/litre (Note:- First quality paint of reputed make firm such as Goodlass-nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge) (DSR 13.85.3). Through Rate

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats whereverrequired, to achieve even shade and colour.. (Note:- First quality paint of reputed make firm such as goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar shall be used as approved by Engineer-in-charge in writing, drum of paint shall be opened in presence of Engineer-in-charge. Two coats (DSR 13.81.2 ) Through Rate

Wall painting with premium acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. (Two coats) (DSR 13.83.2) Through Rate

N.S Items Provision for top soil conservation (excavation of 20 cm layer, stacking soil in 40 cm layer, mulching and relaying the same) after Soil Fertility test report from accredited Lab showing soil water percolation, water table (pre and post monsoon), top soil fertility (N,P & K values). (NS).

Earth work in excavation by mechanical/manual means in foundations and basement for all widths up to a depth of 4.5 Mtrs. and for all width in all type of soil/Rock/boulder/kankar etc. as encountered at site including disposal of excavated material for all lead & lift. The Excavated material shall be the Property of department. This Material shall be disposerd as per direction of the department. The permission required from mining department shall be obtaining by the contractor at his cost. Part of the excavated material shall be used for refilling as per direction of the Department. (N.S)

Providing & Fixing Vitrified Tiles 600 x 600 mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand morter 1:3 and joint will be 4 mm wide instead of zero joint by using spacers to ensure uniformity of joint duly filled with epoxy grout minimum depth upto the thickness of tile of reputed make such as pidilite (T-13 Roff), Mapaie, Laticrete, Ardex Endura as approved by Engineer-in-charge. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO. (Double charged tiles shall be used as approved by Engineer in charge. (NS). A) Basement

Ground floor

First floor

Second floor

Providing & Fixing Vitrified Tiles 600 x 600 mm of approved make skirting/dados, pillars, wall facing, laid in any pattern as specified over base of 20 mm thick cement coarse sand morter 1:3 and joint will be 4 mm wide instead of zero joint by using spacers to ensure uniformity of joint duly filled with epoxy grout minimum depth upto the thickness of tile of reputed make such as pidilite(T-13 Roff), Mapaie, Laticrete, Ardex Endura as approved by Engineer-in-charge. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO. (Double charged tiles shall be used as approved by Engineer in charge. (NS). A) Basement

Ground floor

First floor

Second floor

Providing and laying pre polished grenite stone 17 mm & above (Colors like:- S-White, Steel Grey, Tan Brown, Marigold, Crystal blue, Rajasthan Black, Copper Silk) in skirting/Dados, resers of steps, pillars, wall facing, laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of grenite including labour for fixing cramps pins and dowels etc. (N.S) A) Basement

Ground floor

First floor

Second floor

Third floor/mumty & machine room

Providing and laying pre polished grenite stone 17 mm & above (Colors like:- S-White, Steel Grey, Tan Brown, Marigold, Crystal blue, Rajasthan Black, Copper Silk) in flooring, laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of grenite including labour for fixing cramps pins and dowels etc. (N.S) A) Basement

Ground floor

First floor

Second floor

Third floor/mumty & machine room

Providing Tower bolts with nuts & screws, etc. complete in all respect to the entire satisfaction of Engineer-in-charge (N.S) Aluminium (Size 250 mm x 12 mm) ISI Marked

Providing Tower bolts with nuts & screws, etc. complete in all respect to the entire satisfaction of Engineer-in-charge (N.S) Aluminium (Size 200 mm x 12 mm) ISI Marked

Providing Tower bolts with nuts & screws, etc. complete in all respect to the entire satisfaction of Engineer-in-charge (N.S) Aluminium (Size 150 mm x 12 mm) ISI Marked

Providing sliding bolts with nuts & screws, etc. complete in all respect to the entire satisfaction of Engineer-in-charge (N.S) ) Aluminium (Size 300 mm x 16 mm)

Providing Sliding bolts with nuts & screws, etc. complete in all respect to the entire satisfaction of Engineer-in-charge (N.S) Aluminium (Size 250 mm x 16 mm) ISI Marked

Providing Door handles with nuts & screws, etc. complete in all respect to the entire satisfaction of Engineer-in-charge (N.S) Aluminium (Size 150 mm x 200 mm x 35 mm) ISI Marked

Providing Door handles with nuts & screws, etc. complete in all respect to the entire satisfaction of Engineer-in-charge (N.S) Aluminium (Size 75 mm x 115 mm x 30 mm) ISI Marked

Providing Butt Hinges with nuts & screws, etc. complete in all respect to the entire satisfaction of Engineer-in-charge (N.S) Aluminium (Size 100 mm x 31.75 mm x 11 mm) ISI Marked

Extra for using Ecosense Enhance Marine blue 6mm th SH 38/37 tempered glass of make AIS or equivalent as per approval of architect (NS )

Providing and fixing Aluminium sheet V-Shaped over expansion joint 0.5 mm thick complete in all respect to the entire satisfaction of Engineer-in-charge. (N.S)

Providing and laying 200mm thick granular sub base consisting of drainage layer confirming to Table 400.1 Grading –VI of MORT&H 5th edition, mixing in a mechanical mix plant at OMC, carriage of mix material to the site of work, spreading in uniform layer with motor grader on prepared surface and compacting with vibratory power roller to achieve desired density complete as per clause No.401 of MORT&H specifications for road & bridge (5th Revision) of 2013

Water Bound Macadam G-II (53 mm to 22.4 mm gauge): Providing, laying spreading and compacting 75 mm thick (av). Stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thicknes,, hand packing, rolling with 3 wheeled steel vibratory roller 8-10 tones in stages to proper grade and camber, applying and brooming requisite type of screening/binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density as per Clause of MORT &H Specificaiton No. 404. of MORT&H specifications for road & bridge (5th Revision) of 2013 as per drawing and design directed by the Engineer complete in all respects (NS)

Construction of Dry Lean cement concrete (M-10) Sub-Base over a prepared Sub grade with coarse and fine aggregate conforming to IS:3873, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/cum optimum moisture content to be determined during trial length construction, concrete strength not be less than as per ISI marked provision MPA at 7 days, mixed in the batching plant, transported to site laid with a paver, compacting with 5-10 tonnes vibratory roller, finishing and curing. Unit=cum, taking output=450 cum (990 tonne), taking batch mix plant of 15.20 cum as per MORT&H specification clause - 601 latest edition (N.S.)

B) FIRE FIGHTING WORK Providing laying ,testing & commissioning of (C) class heavy duty MS pipe conforming to IS 3589/ IS 1239 including Welding ,fittings like elbows ,tees ,flanges,tapers, nuts bolt ,gaskets etc . and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complite as required . MAKE HISAR JINDEL, TATA, PARKSH SURYA . (DSR 7) A) 250 mm dia (MINIMUM 6.3 MM THIKNESS) (DSR code No. 7.10)

200 mm dia ( MINIMUM 6.3 MM THIKNESS) (DSR code No. 7.9)

150 mm dia (DSR code No. 7.8)

100 mm dia (DSR code No. 7.7)

80 mm dia (DSR code No. 7.6)

65 mm dia (DSR code No. 7.5)

50 mm dia FOR DRAIN (DSR code No. 7.4)

40 mm dia (DSR code No. 7.3)

32 mm dia (DSR code No. 7.2)

25 mm dia (DSR code No. 7.1)

Providing laying ,testing & commissioning of ( C ) class heavy duty MS pipe conforming to IS IS 1239 /3589 i/c fitting like elbows ,tees ,flanges ,tapers ,nuts bolt , gaskets etc .in ground including welding ,excavation & providing cement concrete blocks as supports , anticorrosive treatment with coaltar /asphalt tape as per IS 10221 reffilling the trench etc .of following sizes complete as required make PYPECOAT/COALTEK A) 150 mm dia (MINIMUM 6.3 MM THIKNESS) (DSR code No. 6.2)

Providing ,fixing ,testing & commissioning of 15mm dia quartzoid bulb type brass sprinklers of rating 68 degree centigrade with required accessories Pendent type (MAKE: TYCO /SAFEX/ HD/ KARTAR, FIRE CUT, NEW AGE) (DSR code No. 21.1)

Providing ,fixing, testing & commissioning of 15mm dia quartzoid bulb type brass sprinklers of rating 68 degree centigrade with required accessories Upright type (MAKE: TYCO /SAFEX/ HD/ KARTAR, FIRE CUT, NEW AGE) location basement 21.2 (DSR code No. 21.2)

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type brass sprinklers of rating 68 degree centigrade with required accessories Horizontal side wall sprinkler type (MAKE: TYCO /SAFEX/ HD/ KARTAR, FIRE CUT, NEW AGE) (DSR code No. 21.3)

Supply, installation, testing & commissioning of sprinkler flexible pipe 1500mm (UL listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (BURST) with branch line (inlet) 25mm NPT male thread to sprinkler head (outlet) 15mm NPTfemale thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complite as required OMEX, FIRE CUT, ATTACK FIRE (DSR code No. 25.4)

Supplying and fixing single headed internal and external yard hydrent valve with instantaneous Stainless Steel coupling of 63mm dia with cast iron wheel ISI marked conforming to IS 5290 (TYPE -A) with blank stainless steel cap and chain as required (MAKE: TYCO /SAFEX/ HD/ KARTAR, FIRE CUT, NEW AGE) (DSR code No. 9.2)

SITC of INTERNAL OR EXTERNAL weather proof standard fire hose cabinet (750mm x600mm x250mm deep) for yard hydrants made of 16 SWG powder coated M.S. sheet having single or double opening glazed (4.0mm thick glass) shutter including necessary locking arrangement by allan key, stove enamelled Fire red finish with "Fire Hose" marked on front, suitable for housing 2 nos. Hose pipe, 1 No. branch pipe & nozzle spanner. (For external hydrant system) (MAKE: FIRE CUT/ MINIMAX/ NEW AGE/ SUPEREX/KARTAR) (N.S)

Supplying and fixing 63mm dia, 15m long RRL hose pipe with 63mm dia male and femaile coupling duly bond with GI WIRE, RIVETS ETC. CONFORMING TO IS 636 (Type -A) as required. (MAKE: FIRE CUT/NEWAGE/ MINIMAX/,KARTAR/ SAFEX (DSR code No. 16.2)

Supplying & fixing 63mm dia Stainless Steel (grade 304) short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 sutitable for instantaneous connection to IS 903 sutitable for instantaneous connection to interconnect hose pipe coupling as required (MAKE: FIRE CUT/NEW AGE/ KARTAR/ MINIMAX /SAFEX) (DSR code No. 18.2)

Supplying and fixing firsr-aid Hose Reel with MS construction spray painted in post office red , conforming to IS 884 complite with the follwing as required . 20 mm nominal internal dia water hose thermoplastic (Textile reinforced ) type-2 as per IS 12585. 20 mm normal internal dia gun metal globe & nozzle. Drum and brackets for fixing the equipmets on wall.connections from riser with 25 mm dia stop gunmetal valve & MSpipe and socket ((MAKE: FIRE CUT / NEW AGE/ MINIMAX / KARTAR/ SAFEX) (DSR Code No.17.00)

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd, for sutitable dia MS pipe connection conforming to IS 904 AS REQUIRED. 4 WAY -150mm dia MS pipe Make Minimax, FIRE CUT, KARTAR, NEW AGE, SAFEX. MINIMAX (DSR code No. 19.2)

Providing , installation, testing and commissioning of stainless steel Y- strainer fabricated out of 1.6mm thick stainless steel, grade 304 , sheet with 3 mm dia hole with stainless steel flange. 250mm dia .MAKE-KARTAR/LEADER, NEW AGE, SANT (DSR code No. 15.5)

Supplying and fixing air vessel made of 250mm dia, 8mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required. MAKE FIRE CUT/ HYDROTECH. (DSR code No. 20)

SITC OF Providing & Fixing of air vessel 450/16000mm dia,height with dish top made in 6mm thick ms pipe complete with 20mm dia brass air valve, 200mm dia stop valve, pressure gauge, stop cock, nipple for fire control room MAKE FIRE CUT / HYDROTECH. (NS)

Supplying and fixing orifice plate made out of 6mm thick stainless steel (Grade 304) with orrice of required size to be fitted between flange & landing valve of external and internal hydrent to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required. MAKE-SANT, LEADER, KARTAR / SAFEX OR EQULENT (DSR code No. 13)

Supplying, fixing, testing and commissioning of butterfly vave of PN 1.6 rating with bronze/gunmetal seat duly ISI markedcomplete with nuts, bolt, washers, gaskets conforming to IS 13095 OF FLOWING SIZES AS REQUIRED MAKE-KARTAR,/ ZOLOTO/ CASTLE, KIRLOSKAR, NEW AGE, SANT, OR EQULENT (DSR code No. 11) A) 250 mm dia (DSR code No. 11.8)

150 mm dia (DSR code No. 11.6)

100 mm dia (DSR code No. 11.5)

80 mm dia (DSR code No. 11.4)

65 mm dia (DSR code No. 11.3)

50 mm dia (DSR code No. 11.2)

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS 5312 complete with rubber gasket. GI bolt, nuts, washers etc. as required MAKE-KARTAR/ZOLOTO/ CASTLE, KIRLOSKAR, NEW AGE, SANT OR EQULENT A) 150 mm dia (DSR code No. 14.7)

100 mm dia (DSR code No. 14.5)

80 mm dia (DSR code No. 14.4)

65 mm dia (DSR code No. 14.3)

50 mm dia (DSR code No. 14.2)

Providing & fixing of pressure switch in M.S pipe line including connection MAKE -INDOFUS/DANFOS/SWITZER) (DSR code No. 22)

SITC of fire brigade draw off connection confirming to IS : 4038-1986 with 150mm Non return valve/ strainer incluiding necessary fittings the word FIRE BRIGADE DRAW OFF to be painted on the box complete all as specified and directed. (MAKE: FIRECUT/KARTAR/ NEW AGE / MINIMAX) (N.S)

Providing, fixing, testing & commissioning of 100mm dia Burden type, Stainless Steel dial type pressure gauge (in Pump Room) including brass isolation valve and pipe having caliberation of 0-15 Kg/cm2. MAKE H.GURU/FIEBIG (N.S)

MECHANICAL/ELECTRICAL PUMPS-Fire Hydrants Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complite in all respect, as required (Diesel Driven Pump) horizontal type, multistage, centrifugal pump of cast of iron body and brinze impeller with stainless steel shaft , mechanical seal conforming to IS 1520 OF Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with autostarting mechanism, 12 /24 volt electric starting equipment, disel tank, exhaust pipe extended upto 10m outside pump house duly insulated with 50mm thick glass wool with 1.0mm thick almunium sheet cladding, residebtial silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the ecent of fault with audio indications, painted with post office red colour etc .as required. MS fabricated, common base plate coupling, coupling guard, foundation bolt etc .as required. MAKE KILOSKER, LUBI MOTHER AND PLATT, ASHOK LEYLAND 2280 LPM at 88 Mtr Head, (DSR code No. 2.4)

Supplying, installation, testing and commissioning of electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft , mechanical seal conforming to IS 1520 (b) suitable HP squirrel cage induction motor,TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volt, 3 phase 50 Hz, ac supply with IP 55 protection for enclosure, horizontal foot mounted type with class 'F' insulations, conforming IS -325 FOR SPRINKLER SYSTEM SYSTEM MAKE KILOSKER, LUBI MOTHER AND PLATT, ASHOK LEYLAND 1.4 (DSR code No. 1.4) 2280 LPM suitable for 88 Mtr Head (DSR code No. 1.4)

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required; (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS; 1520. Suitable HP squirell cage induction motor tefc type suitable for operation on 415 volt , 3 phase 50 HZ AC supply with IP 55 class of protection for enclosure , horzontal foot mounted type with class- 'F' insulation,conforming to IS; 325 M.S fabricated common base plate, coupling, coupling guard, foundation bolt etc as required. M.S fabricated bolt etc as required .Suitable cement concrete foundation duly plastered and with anti vibration pad MAKE KILOSKER, LUBI MOTHER AND PLATT, ASHOK LEYLAND 180 LPM suitable for 88 Mtr (DSR code No. 3.1)

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required ; (Terrace Pump) (a) Horizontal type, multistage , centrifugal , split casing pump of cast iron body & bronze impeller with stainless steel shsft , mechanical confirming to IS; 1520 (b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volt, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure , horiziontal foot mounted type with class - 'F' insulation, conforming to IS- 325 (c ) M.S fabricated common base plate ,coupling, coupling guard , foundation bolt etc as required (d) Suitable cement concrete foundation duly plastered and with anti vibration pads. MAKE KILOSKER, LUBI MOTHER AND PLATT, ASHOK LEYLAND 900 LPM at 35 m head (DSR code No. 4.1)

SITC OF DOL type fire pump panel suitable for 900 lpm fire pump 415 V+/-6 volts, panel shall be free standing floor mounting sheet metal enclosed dust and verming proof. Panel shall be provided with heat shrinkable sleeves and shall be coloour coded. The panel shall be suitable for cable entry from top or bottem. The minimum fault rupturing for all incoming and outgoing switch/ breakers shall be 35 KA. The panel shall be fabricated.Auto mannual Starters with change over system. MAKE (FIRE CUT,HYDROTECH fire cut) (N.S)

Supplying , installation , testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required ; (Terrace Pump) (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shsft , mechanical confirming to IS; 1520 ( b ) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volt ,3 phase ,50 Hz , AC supply with IP55 class of protection for enclosure , horiziontal foot mounted type with class - 'F 'insulation , conforming to IS- 325 ( c ) M.S fabricated common base plate ,coupling ,coupling guard , foundation bolt etc as required ( d ) Suitable cement concrete foundation duly plastered and with anti vibration pads . MAKE KILOSKER , LUBI MOTHER AND PLATT , ASHOK LEYLAND 450 LPM at 35 m head (DSR code No. 4.2)

SITC OF DOL type fire pump panel suitable for 450 lpm fire pump 415 V+/-6 volts,panel shall be free standing floor mounting sheet metal enclosed dust and verming proof.Panel shall be provided with heat shrinkable sleeves and shall be coloour coded. The panel shall be suitable for cable entry from top or bottem. The minimum fault rupturing for all incoming and outgoing switch/ breakers shall be 35 KA. The panel shall be fabricated.Auto mannual Starters with change over system. MAKE (FIRE CUT,HYDROTECH attack fire (NS)

Supplying and making end termination with brass compression gland and almminium lugs for following size of PVCand PVCsheathed /XLPE almuminium conductor cable of 1.1 KV grade as required (MAKE:RR/FINOLEX/polycab) a) 3.CORE x 95 sq. mm (From Fire Fighting Control Panel to main fire AND SPRINKLAR pump) (DSR code No. 9.1.13)

3 CORE x 35 sq. mm (From Fire Fighting panel to jockey pump) (DSR code No. 9.1.10)

2 core x 1.5 sq .mm For pressure switch to fire panel and fire annuciator panel and flow switch) supplying and drawing FRLS PVC insulated copper conductor cable (DSR code No. 1.17.2)

3.CORE x 10 sq. mm (From Fire Fighting Control Panel to main fire pump) (DSR code No. 9.1.7)

Supply, installation, testing of 16 zone fire annuciatior indication panel location fire control room make fire cut /attack fire /hydrotec (N.S)

Providing & fixing flow switch in following sizes M.S pipe including connection etc as required.150mm diamake system sensor/ hd / new age. (DSR code No. 23.2)

Proviing, fixing, testing & commissioning of installation control valve of cast iron body, brass /bronze working parts comprising of water moter alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser / sprinkler system activates , pressure switch, cock valve complete with drain valve and bypass , test control box , ball valves MS PIPE OF REQUIRED SIZE, FLANGES, ORIFICE PLATE, GASKET ETC OF FOLLWING SIZES AS REQUIRED 150 MM DIA MAKE - HD, OMEX , GETECH, NEWAGE (DSR code No. 24.3)

AUTO GLOW EXIT SIGNS AUTO GLOW EXIT SIGNS AND INDICATION SIGNS SIZE 12 "x 6", MAKE FIRE CUT AND ATTACK FIRE ,DP lndication every exit point,fire point,fire extinguisher (N.S)

FIRE EXTINGUISHERS SUPPLY AND INSTALLATION of ISI marked (ISI MARK 15683) portable Co2 fire extinguisher of capacity 4.5 kg flat base including valve , dischargeone metar long hose of . meter complete in all respect with explosive certificate .(MAKE: Ceasefire/FIRE CUT /Minimax, safex / kanax (N.S)

SITC of ISI marked (IS: 15683) portable ABC multipurpose filled by 90% (MAP ) mono amonioum phosphate powder, nitrogen pressurised type fire extinguisher, Capacity 6 kg with 90% map complete in all resp. MAKE (FIRE CUT, CEASE FIRE, MINI MAX, SAFEX, KANAX) (N.S)

SITC of Clean Agent type ISI mark IS code 15683 2006 Fire Extinguisher capacity: 2 kg MAKE (MAKE FIRE CUT,, CEASE FIRE ,MINI MAX ,SAFEX , KANEX,) location - o.t room, nursing station lab machinry room pantry kitchen (N.S)

SITC of 5 kg modular type self operated on 68o temperature Clean Agent type CE certified Fire Extinguisher filled with NAFPIV clean agent gas MAKE (FIRE CUT ,CEASE FIRE,MINI MAX,SAFEX KANAX) location electrical shaft ,electrical control room servar room other places where water or other camical are prohibited. (N.S)

SITC of 50 KG DCP (Dry Chemical Powder) Trolley type fire extinguisher as per IS 16018I jet length minimum 8 mtr minimum discharge time 40-50 sec,tested on 30 kgf/cm2 MAKE (FIRE CUT ,CEASE FIRE ,MINI MAX, SAFEX, KANAX. location dg room, fire control room, ground floor of every block. (N.S)

SITC of 50 KG Mechanical Foam AFFF Trolley type fire extinguisher as per IS 16018 jet length minimum 10 mtr minimum discharge time 60-180 sec,tested on 35 kgf/cm2 with 2 kg co2 external fire extinguisher MAKE (FIRE CUT ,CEASE FIRE ,MINI MAX ,SAFEX , KANAX , ) location dg room , fire control room , ground floor of every block . (N.S)

SITC of 9 ltr capacity Fire Bucket made in 16 guage MS filled by 9 kg sand with MS angle stand having arrangement of hanging 6 buckets with shed MAKE (FIRE CUT ,KARTAR) (N.S)

FIRE CHECK DOOR SITC of 46mm steel fire check door of 120 minut fire rating confirming to bs 476 part -22 and is 3614 part-11 fabricated with 2 no , 1mm thick galvnized steel sheet sandwiching with proprietary fire resistant insulation materials in between. The door frames are manufactured from 1.5mm thick galvanized steel sheet pressed from to double rebate profile of size 143mm x 57 mm . the door frame and door shutters to finish with powder coatingSITC OF 2HR FIRE RATED METAL DOOR MAKE LAKSHITA FIRE, INDIAN FIRE, FIRE CUT. location- basement stair case, electrical cantrol room and all floor stir case where there is no natural vantilation (N.S)

C) PH WORK Excavation of trenches in streets, lanes or in Open areas for storm sewer, sewers running by Gravity nd manholes to full depths as shown In drawings including shoring timbering of Poling boards, frame System type, dressing to correct Sections and dimensions, according to templates and levels, Dewatering, provision for diversion of traffic, cutting trees and Bushes etc. Night signals, profiles, pegs, sight rails, oning rods,Crossing over trenches for access to the houses, watching fencing, Etc., fixing and maintenance of caution boards, refilling of trenches, Watering of refill, in 15 m layers, ramming and restoration of Unmetalled or unpaved surface to original condition and removal Of surplus soil from site of work, upto a lead of 1 Km in ordinary soil. a) for depths of excavation exceeding 3 metres, but not exceeding 4.5 metres (HSR 6.10)

Boring for hand-pump in clay, fitting strainer and pipe (b) above 75 mm dia bore, but not exceeding 100 mm dia (i) from 0 to 15 meter (HSR 26.10 (b) (i)

Drilling and tapping cast iron pipe line of all diameters and screwing in ferrule and connections. 40mm I/d (HSR 28.22)

Cutting holes upto 23 cm square through brick work in mud walls for pipes and making good including repointing replastering and finishing according to existing finish where required. (HSR 28.23) a) 11.43 cm thickness of walls

b) 22.86 cm thickness of walls

Bailing out water from the trenches for making new connections in fully charged pipe lines including cleaning, trimming and dressing the trenches to correct alignment and grade as required by the Engineer-in-charge. (a) Upto 200mm I/d (HSR 28.47)

Providing and placing in horizontal layers filtering media screened, washed and cleaned as described below: (a) Top layer: - Fine sand screened, cleaned and washed and graded (effective size 0.2 to 0.4 mm with uniformity coefficient 2.0 to 3.0) from Ghaggar or other approved source (HSR 28.50a)

Providing and placing in horizontal layers filtering media screened, washed and cleaned as described below: (b) Second layer :- coursed sand screened, cleaned and washed and graded from 3 mm to 6 mm (from Ghaggar or approved equivalent quarry)

Providing and placing in horizontal layers filtering media screened, washed and cleaned as described below: (c) Third layer: - Bajri screened washed and graded from 6 mm to 20 mm (from Ghaggar or approved equivalent quarry)

Providing and placing in horizontal layers filtering media screened, washed and cleaned as described below: (d) Fourth layer: - Bajri (coarsed) screened and washed graded from 20 mm to 25 mm (from Ghaggar or approved equivalent quarry)

Providing and placing in horizontal layers filtering media screened, washed and cleaned as described below: (e) Bottom layer:- Broken stone, screened, washed and graded from 50 mm to 75 mm (from Ghaggar or approved equivalent quarry)

Constructing brick masonry inspection chamber sizes as given below upto 0.60 meters average depth in cement mortar 1:5 lime concrete with 40 percent lime mortar 2:3 in foundation cement concrete 1:2:4 benching 12mm thick cement plaster 1:2 with a floating coat of 1 mm thick of neat cement RCC 1:2:4 slab 100mm thick/C.C. topping 50mm thick with 455 mm x 455 mm / 455 mm x 610mm inside light duty C.I inspection chamber cover and frame weight as per I.S.I specification painted with 3 coats of black bitumastic superior paint complete as per standard design. b) Size 450 mm x 600 mm inside (with 455 mm x 610 mm cover and frame light duty single seal pattern I weighing 38 kg with C.C.topping) (HSR 29.84)

Providing, lowering, laying, cutting (cut surface to be uniformity finished) jointing with rubber rings marked with IS:5382 and testing of SPIGOT AND SOCKETTED RCC NP2 MARKED WITH IS:458-1988 and specials into trenches for all depths including carriage, loading, unloading, stacking, handling, re-handling etc. complete in all respects to the satisfaction to the Engineer -in-charge a) 200 mm i/dia RCC NP2

Providing and fixing SFRC manhole covers and frames markd with IS: 12592 including setting the same to correct lines and levels in 1:2 cement sand mortar over manhole including carriage loading, unloading stacking, handling, re-handling etc. complete in all respect to the satisfaction of engineer-in-charge. Type: Extra heavy duty set (MD-10) 560 mm clear opening.

Providing and laying SW pipe grade –A in standard length of 600 mm each pipe marked with IS :651 and their lowering, cutting , jointing & testing as described in HSR item No. 29.38 to 29.40 including the cost of jointing material as well as carriage, loading, unloading , stacking., handling, rehandling etc. complete in all respect to the satisfaction to the Engineer-in-Charge (HSR 29.95) i) 150 mm i/d

ii) 100 mm i/d

PROVIDING AND FIXING IN POSITOIN BEST INDIAN MAKE (to the approval of the Engineer-in-charge). INDIAN TYPE ORISSA OR ORYA WATER CLOSET SUITE for Sinking into floor, with raised foot treads COMPLETE WITH 100 MM H.C.I, ‘P’ TRAP with or without vent as required and all OTHER NECESSARY FITTINGS as fully described in item no.30.1 above (i) white 580mm (HSR 30.2)

Providing and fixing in position best Indian make European type water closet suite with concealed 'P or 'S trap with or without vent (as approved by the Engineer-in-charge) and all other necessary fitting as fully described in item no. 30.3 above. (HSR 30.6) (i) white

Providing and fixing best indian make plastic hygenic seat with lid complete instead of hollow black or white plastic seat and lid (HSR 30.13) (i) white plastic seat (solid) (HSR 30.13)

Providing and fixing in position 32mm dia G.I waste pipe embedded in wall or lead waste pipe (weighing 3.47 kg. per metre and 2.8 mm thick) upto floor level including cost of wipped solder joint etc. complete (as required by the Engineer-in-charge) (HSR 30.48)

Providing and fixing in position best quality stainless steel sinks with complete fittings as fully described in utem no 30.51 above (HSR 30.53) a) 600 mm x 450 mm x 200 mm

Providing & fixing in position best indian make shower with 15 or 20 I/d in-let (HSR 30.66) 125 mm diameter rose showers

Providing and fixing in position best indian make towel rails fixed in with rawlslugs embedded in walls with C.P Brass screws, complete in all respect including cutting and making goods the walls etc. (HSR 30.68) a) 25mm dia C.P brass adjustable. ii) 600mm long.

Providing and fixing in position glass shelf fixed in with rawl plugs with C.P brass screws complete including cutting and making good the walls etc. (HSR 30.69) c) Vitreous chinaware shelf 560 mm long i) white.

Providing and fixing in position best Indian make bevelled edge 5.5 mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 nos. chromium plated brass screws and washers over rubber washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the Engineer -in -charge) complete including cutting and making good the walls etc. (HSR 30.71) a) Indian make (I) 600mmx450mm

Providing and fixing in position 15 mm I/d C.P. brass bib cocks of best quality (as required by the engineer I charge) (HSR 30.75) (a) Bib cock long body

(c) Bib cock

Providing and fixing in position C.P brass stop cocks (as approved by the Engineer-in-Charge) (HSR 30.76) a) 15mm stop cock i) Stop cock male and female end.

ii) Concealed stop cock with flange

Providing and fixing in position best indian make flexible tube connection (HSR 30.82) b) C.P brass i) 15mmx300mm.

Providing and fixing in position M.S or heavy flat iron clamps made out of M.S flat not less than 5 mm of the approved deign for fixing C.I soil waste vent or anti pipes to walls complete in all respects including cutting and making good the walls and floors etc. and painting. (HSR 30.88) For 100 mm internal diameter pipes

For 75 mm internal diameter pipes

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with H.C.I. grating 150mm x 150mm cast iron cover weighing approximately 7.26kg and frame clear opening 300mmx300mm and outside size 330mmx330mm and chamber including cost of all brick work in cement mortar 1:5 cement concrete 1:8:16 in foundation, and cement concrete 1:2:4 in coping around C.I cover and frame etc. with three coats of black bitumastic superior paint of approved manufacture on all C.I work as per standard design, minimim depth of water should be 150mm with a minimum seal 50mm (HSR 30.114) a) 100mm internal diameter S.W gully trap.

Providing and fixing HDPE water storage tanks of sintex, Diplast, O.K. supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing Iin position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction to the Engineer. (HSR 30.119) 1000 Ltr. Cap.

DSR ITEMS Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 32mm Dia (DSR 17.28.1.1)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge (DSR 18.7) a) 15mm

Providing & fixing G.I Pipes complete with G.I fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting and making good the wall: (DSR 18.11) (i) 15 mm internal diametre of pipeline

(ii) 20 mm internal diametre of pipeline

Providing and fxing gun metal gate valve with C.I. wheel of approved quality (Screwed end) (DSR 18.17) a) 20mm

Providing and fixing GI Union in GI pipe including cutting and threading the pipe and making long screws etc. complete (new work) (DSR 18.46). A) 15mm

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge (DSR 18.53A)

NS ITEMS Providing and fixing 15 liters capacity low level vitreous china ware cistern complete with flush bend all other necessary fitting instead of C.I high level cistern complete with fitting. (NS)

Providing and fixing in position best indian make flat black or angular lipped front urinal 465 mm high consisting of:- Providing & fixing Infra red based electronic flushing system operated on 6V DC (4AA) battery for urinals comprising of solenoid valve, concealed built in strainer & flow mechanism piping, flush mounted sensors with all accessories & fittings complete in all respect in fully operational condition etc including cutting and making good the wall where required. (NS)

Extra for low flow faucets as per GRIHA compliance complete in all respect to the entire satisfaction of Engineer-in-charge (NS)

Providing/ fixing sink mixers as per GRIHA compliance complete in all respect to the entire satisfaction of Engineer-in-charge (NS)

Extra for low flow faucet for GRIHA compliance complete in all respect to the entire satisfaction of Engineer-in-charge (NS)

Providing and fixing Brizzio Oval marble brown Cetemic type wash basin of size 600x400 mmwith a pair of 15 mm C.P. brass pillar taps with elbow operated levers complete in all respects. 600mmx400mm with one no.Pillar tap (NS)

Providing & fixing PVC pipe (4kg/cm2) duly slotted IS-4985:1988 including cost of adhesive, carriage, loading, unloading etc. complete in all respects to the satisfaction engineer incharge. size : 160 mm od (NS)

Providing and fixing Steel bar embedded plastic steps of size 263 mm x 165 mm of orange colour, conforming to specifications, in pump chambers, manholes etc. having minimum 3 mm thick Polypropylene polymer confirming to IS : 10910 encapsulated on 12 mm dia ribbed steel bars per IS : 1786

Providing and fixing PVC floor traps ISI marked of the self cleaning design with C.P brass hinged grating with frame with or without vent arm and including cement concrete 1:2:4 under and around the floor trap where required upto floor level complete in all respects including cutting and making good the walls and floors etc. minimum depth of water should be 150 mm with a minimum seal of 50mm b) With 75mm I/d outlet. (NS)

Providing and fixing in position PVC 50 mm internal diameter outlet plain nahani trap ISI marked of the self cleaning design with CP brass hinged granting with frame weighting 6.80 kg each fixed complete as fully described in item no. 30.89 (a) with 75 mm i/d outlet plain Nahani trap (NS)

D) RECOVERY ITEMS The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Earth obtained on excavation of basement have been calculated taking assumption that theoretical earth will be retrieved. The excavated earth will be issued for use in any of the item for the work after modification (bringing it to required specifications) as per approval of employer. In case it is not possible to use this earth on the work, the agency can take away this earth after approval from employer; This earth will be issued at the price quoted by the agency. (i) Excavated earth @ Rs.183.00/- Per Cum with all lead & lift. Note: - All quantities of the above earth have worked out on the basis of theoretical quantities laid on this building. However, agency may visit site before quoting rates and assess the extent of retrieved earth. There shall be no measurement after actual excavation and if earth after excavation is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price.

SARINS

KLV New Tech Constructions Pvt. Ltd.

Gauri Buildcon Pvt. Ltd.

LALIT KUMAR CONTRACTOR