Repair and Refurbishment of MPCB Office at Tarapur, Boisar - Interior and Allied Services

Amount

Demolition Works

Removing rich mix cement concrete including stacking and disposing the spoils as directed with all leads, lifts etc, complete.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material with all leads, lifts etc.

Dismantling brick masonry in lime or cement mortar and stacking and disposing the materils as directed with all leads, lifts etc.

Removing doors and windows with frames/jamb lining and stacking and disposing the materials as directed with all leads, lifts etc. complete.

Removing cement tiles, plaster or marble or polished shahabad floor or dado including stacking the materials as directed with all leads, lifts etc. complete

Removing wooden or A.C. partition including frame work and stacking the materials as with all leads, lifts etc. complete.

Removing of all furnitures/storage units such as tables, chairs, cupboard etc and stacking the servicable materials as directed and disposing of unservicable materials with all leads and lifts etc. complete.

Repositioning of all furnitures/storage units such as tables, chairs, cupboard etc as directed with all leads and lifts etc. complete.

Demolishing waterproofing/brick bat by manually/ by mechanical means including disposal of unserviceable material with all lead and lifts as per direction of Engineer-in-charge.

Structural Repairs

Polymer Modified Mortar (PMM)

Repairs to RCC Damaged members such as slab, beam, columns by using Readymix Polymer Modified Mortar (upto size mentioned below in mm thick). The damage member is to be chipped of loose concrete with all safety measures such as propping, protective covering. The steel exposed should be removed of loose rust from the reinforcement bars by wire brushing, ligth hammering etc. and applying sulphate and chloride free inorganic single component rust remover (Rusticide or equivalent) confirming to IS 9077. After 24 hours of application of rust remover, loose particles shall be removed by brush. Over it, bonding coat slurry of high performance acrylic polymer Polyalk EP or other euivalent in proportion of 1kg Polyalk EP with 0.5 Kg of cement to to applied for bonding of Ready mix Polymer Modified Mortar. The Polymer Modified mortar can be sprayed or trowel applied. When applying by hand it must be forced tightly into the substrate to ensure complete contact with the substrate. Work to be executed by certified applicator only and work shall be guaranteed for 5 years the guarantee shall be legally mentioned on stamp paper. (Internal & External Area)

Micro-concrete

For replacing distressed/loose/ cracked/ porous carbonated, loose part of concrete with fiberous micro-concrete and repairing the damaged surface of concrete, fix the formwork / shuttering across the profile of damaged structural element, pour the free flow ready mix micro concrete withwater as per manufactures specifications in the formwork. Microconcrete should be mixed in steel tray homogeneously makeup concrete is based on type of structural element and its location. The work should be carried out with all the safety measures like helmet, safety belt and adequate labour insurance under the supervision of qualified supervisor etc.

Reinforcement

Replinishment / making up of lost area of reinforcement due to corrosion providing additional steel reinforcement. The steel shall confirm to IS 1786 grade Fe 415/ Fe500. Anchore the steel rebar in sound concrete body up to desired depth by structural GRADE ashenional sive Anchor fasteners Fixing of rebar’s is to be welded or Binded by binding wires to existing steel at regular grid as in compatibility to original design. Any additional space bars are welded to keep main reinforcement in perfect vertical position to keep the bar equidistant from center of gravity and center of mass, minimum diameter of stirrups should be 8mm dia for columns and 10mm dia for beams and maximum spacing should by 0.15m C/C of directed by the structural Engineer and designer results, Minimum tensile strength should be 430 N/mm2 aligning be carried out with all the safety measures like helmet, safety belt and adequate labour insurance under the supervision of qualified supervisor. etc...complete

Excavation Works

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material with all leads and lifts, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. By Mechanical Means or manual means

Filling new earth/available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, with all leads and lifts.

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete.

Providing and laying Cast in situ/Ready Mixcement concrete in M20 of trap/ granite/quartzite/gneiss metal including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Providing pre-constructional antitermite treatment to building at different stages of construction by applying chemical emulsion Chlorpyrifos 20% E.C. doses as specified in IS:6313 - 2001 edition, list for different stages, including pre-constructional soil treatment in foundation and plinth including drilling the holes of requisite size with inserting GI pipes and plugs as well along the exterior periphery of building below apron so as to form chemical barrier including giving treatment to wooden members including all labour, material, tools & plants etc. complete with 5 years guarantee.

RCC Works

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. columns, beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork,cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

core cutting in existing RCC wall or slab upto 200 mm dia and upto 300 mm deep. The rate shall include making good of the core with airtight micro concreting and water proofing after completing the work. The work should be tested for leak proof to the satisfaction of the EIC/Architect

100 mm dia

150 mm dia

200 mm dia

Civil Work

Providing Autoclaved Aerated Concrete Block masonary upto 300mm of Ecolite or equivalent make conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in superstructure including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972

Providing second class Burnt Brick masonry upto with conventional/I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete

Providing internal cement plaster of all thickness in single/double coat as per site requirement in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete

Providing rough cast cement plaster externally & in two coats to concrete, brick or stone masonry surfaces in all positions with base coat of 12 to 15 mm thick in C.M. 1:4 and rough cast treatment 12mm thick in proportion 1:1 1/2:3 including scaffolding and fourteen days curing complete

Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1: 4 cement mortar including neat cement float, filling joints with epoxy grouting, spacers, curing and clearing etc. complete. a)flooring b) Skirting

Providing and laying vitrified stone effect finish tiles having size 590 to 605 mm x 590 to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including required position laid on a bed of 1:4 cement mortarincluding neat cement float, filling joints with epoxy grouting, spacers,, curign and cleaning etc. complete. a)flooring b) Skirting

Providing & fixing in position Vitrified Tile Dado & Skriting in approved shape, size & colour and pattern in dado truly in plumb upto part or full height of wall with machine cut top edge as per the drawings over cement, sand. backing coat plaster of 15mm / required thickness in CM 1:4 proportion, including fixing with cement paste of required consistency to avoid any possibility of hollowness behind the tiles, filling the joints with epoxy grouting, spacers and matching color pigments including curing, scaffolding etc. complete as per drawing, specifications and as directed by the Engineer - In - Charge.

Providing and laying 10,12 & 15 mm thk Vitrified Material paver tiles of Pavit Decor or Equivalent approved make in all colours and shade in flooring, skirting, dado, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness groove, including grouting of joint with Epoxy material etc complete as per direction of EIC.

Providing and laying granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. of approved make, type and colour On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete.

Providing and fixing machine cut machine polished 18 mm to 20 mm thick granite stone of approved make,type and colour for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc complete

Providing and constructing 600 mm Wide Granite wash basin/Pantry Platform by using 18 mm thick (+/- 2 mm tolerance ) mirror polished granite stone at top to be laid on 16mm thick sandwich type marble stone base, set in cement mortar 1:4, all exposed edges to be rounded and polished. Also providing vertical facia of granite as shown on drawing. Rate to include making opening for wash basin and pillar tap with all exposed edges polished . All joints shall be made water tight in perfect line, level & slope as desired including curing, polishing & cleaning all joints and floating in coloured cement mortar. Granite shall be of approved colour & shall be as per Architects approved lot. (Only plan area will be measured. Wastage due to dimensional difference, pattern, cutting sizes available will be to the contractors account). Rate to include all holes & openings required for fixtures and fittings. All as per drawing and instructions from Engineer in charge. SS Sink / Sink to be Paid Separately.

Fabrication Works

Providing and fixing mild steel grill work for windows, ventilators, storage etc 20 kg/sqm as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting including 1 coat of primer complete

Providing and fixing collapsible steel gate in one / two leaves with hot rolled vertical channels of 18 x 9 x 3 mm minimum size, crossings of M.S. flats of size 18 x 5 mm T or E section for runner of minimum 40 x 6 mm size for flange, M.S. flat for top runner of minimum size 40 x 12 mm with roller wheels confirming to grade F. G. 150 fitted with snap headed rivets of minimum size 6 mm max. spacing of vertical channels be 100 mm enclosed gate position and clear space of 150 mm between two sets of crossings with hold fasts, stoppers, spaces, handles, locking arrangement and one coat of red lead primer and oil painting etc. complete. (I.S. 105211983).

Structural steel work riveted, bolted or welded in built up sections, staircase, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing structural steel work in single stanchions composed of R. S.J. Channel etc. with caps, bases, mild steel plated, angle brackets, cleats, gusset plates, anchor bolts etc. as per detailed designs and drawings or as directed including cutting, fabrication, hoisting, erecting fixing in position, making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it, two coats of oil painting approved quality and shade etc. inclusive 1 coat of primer complete.

Providing and fixing 40mm diameter and 1.5 mm thick Stainless steel hand railing in S.S.304 Grade including fabricating ,fixtures, errecting, necessary welding, grinding, finishing, buffing to stainless steel pipe etc. complete

Waterproofing Works

Providing and laying six courses water proofing treatment with bitumen felt over roofs consisting of first, third and fifth courses of blown or / and residual bitumen applied hot at 1.45, 1.20 and 1.70 kg per square metre of area respectively, second and fourth courses of roofing felt type 2 grade I (fibre base self finished bitumen felt) six and final courses of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic decimeter per sqm including preparation of surface, excluding grading, compete. (Terrace Area)

Providing and Applying waterproofing and filling for Toilet & other wet areas in following parts as per the specifications listed below and as approved by the engineer-in-charge with a guarantee of 10 years : Toilet & Wet Areas Waterproofing (viz-steam room, shower, kitchen etc)

The waterproofing material using M/s. Hitchins-singapore Formdex Uni / Vandex BB 75 E / Blue Hy Seal a cementitious, two-component, polymer-modified, heavy duty slurry waterproofing membrane. Formdex Uni / Vandex BB 75 E / Blue Hy Seal can be applied to both horizontal and vertical masonry surfaces with excellent of 1.3N/mm2 adhesion to substrate against active or passive water pressure.It has high tensile strength of 1.6 N/mm2, elongation of 127% & crack bridging capacity of 2.0mm & is resistance to water pressure @ 6.0 Kg/cm2. The FIRST PART: Cleaning the surface for treatment by removing dust, dirt, surface laitances, loose materials etc by wire brushing & water jetting including making covings in CM1:4 added with Aqua Bond 150 @ 250ml/ bag of cement, at junction of floor slab & vertical wall prior to the waterproofing treatment. Providing and carrying out FORMDEX UNI / Vandex BB 75 E / BLUE HY SEAL two component polymer modified cementitious water proofing treatment on to slab and walls upto 1.0m height in genaral & 2.0m height in shower areas on damp surface @ 1.0kg/sqm/coat in two coats brush applied and reinforcing with chopped strand fiber glass mat of 225 gsm at upturns and around all detailing as per the manufacturers.

The Second Part PROTECTIVE PLASTER TO FLOOR & WALL:consisting of providing and laying avg. 10-12 mm thick, CM 1:4 screed / plaster to floor & walls admixed with Integral Waterproofing Compound of approved makes as per manufacturer's specifications

The Third Part consisting of Providing and filling110mm thick Block bat coba in the sunken portion in CM 1:4 including approved make of waterproofing admixture as per the manufacturer's specification, finished on the top with screed 30mm thick in CM 1:4, kept rough to receive subsequent tile, curing and testing for water tightness for 7 days etc. complete.

Extra Thickness if required over 110 mm providing Block bat coba light in the sunken portion in CM 1:4 including approved make of waterproofing admixture as per the manufacturer's specification, finished on the top with screed in CM 1:4, kept rough to receive subsequent tile, curing and testing for water tightness for 7 days etc. complete.

Finishing

Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete.

Providing and applying external raincoat painting with crack filling acrylic polymer based chemical compound coating to the external surface of walls to prevent water seepage in the masonry walls during monsoon added with required shade Steiner to give required shade to the surface in two coats. Including providing three coat of priming of polymer base primer including preparing surface scrapping the existing loose old paint, removing loose particles of sand on the surface opening and cleaning the cracks developed in the external plaster, removing loose particles by chiseling, filling cracks by chemicals compound of approved make with proper penetration etc. Coating of Raincoat with the help of brush and as per instructions and specification given by manufacturer and with instruction from Engineer in-charge. Work shall be executed by certified applicator only and covering gurantee of 5 years on court stamp paper of Rs. 500/- and necessary testing etc. complete.

Providing and applying plastic emulsion paint conforming to IS:5411-1991 part I of superior quality of approved make, colour and shade to the old & new surfaces in two coats over primers, including scaffolding, preparing the surfaces to receive the paint and applying putty etc. complete.

Providing and applying pearl/ luster finish paint of approved colour and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc. complete.

Providing and applying two coats of textured synthetic paint of approved shade and quality and one coat of primer before applying textured paint including scaffolding if necessary preparing surface by thoroughly cleaning oil, grease, dirt and other materials as required, etc. complete.

False Ceiling

Providing and Fixing Soft Fibre Acoustical Suspended Ceiling System with Optra (Bevelled Tegular) Edge Tiles of size 15mm Exposed Grid. The tiles should have Humidity Resistance (RH) of 95%, NRC 0.9 - 1.0, Light Reflectance ?85%, Colour White, Fire Performance UK Class 0 / Class 1 (BS 476 pt - 6 &7) in module size of 600 x 600 x 15mm , suitable for Green Building application, with Recycled content of 66% GW and 74% RW. The tile shall be laid on precoated G.I channel 32 with 15 mm wide T - section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm and 600 mm Cross Tees with a web height of 32 mm and a load carrying capacity of 7 Kgs/M2 with a minimum pull out strength of 100 kgs. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with Suspension system The Tile and Grid system used together should carry a 10 year warranty. products approved as per GRIHA and BS 476 etc. complete.

Providing and fixing in position Plain Gypsum / Gypsum moisture resistant board false ceiling with 12.5 mm thick Gypsum boards, screwed/fixed to the under structure of suspended G.I. Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50 mm maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in all respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etc. all complete.

Providing and fixing in position 19 mm thk. plywood for soffit/wooden ceiling with approved laminate finished including required teak wood frames, supports & mouldings, with exposed sides finished with melamine polish. Item to be completed in all respects as per drawings & instructions from Enginner In Charge.

Providing and fixing Wooden rafter at all height including providing and fixing of aluminium frame work and rafter made up of ply using 9/12/19 mm with complete hardware fitting etc complete as per direction of Engineer in charge

Carpentry Works

Providing and fixing in position Aluminium Frame Work of Square hollow sections of given size for partitions, paneling, boxing, soffits etc. with vertical & horizontal members at not more than 600 mm center to center. All complete including necessary additional supports, bracing, runner etc. so that lateral movement is arrested. as per instructions of Architect. Frame work will be measured and paid as per actual measurement on site. Rates quoted shall include the cost of providing and fixing supports up to ceiling. All complete as per detail drawing, as specified and as directed by Architect.

Size 50 x 50 x 1.62 mm

Size 50 x 25 x 1.62 mm

6mm thick Marine grade Plywood

9mm thick Marine grade Plywood

12 mm thick Marine grade Plywood

19 mm thick Marine grade Plywood

Providing and fixing 1.5 MM thick group matching Laminate of approved quality and make, of required size and width as per site condition including surface preparation pasting with approved adhesive and finishing it evenly to get flat surface. The cost of openings for switches, AC Facia, any other cutout etc. shall be included in the rates quoted. complete as per detail drawing & directions by Architect. No extra payment will be made towards providing any pattern .

Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS: 8183 having density 30 kg/m3, 50 mm thick, wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss crossing GI wire etc. complete as per directions of Engineer-in-Charge.

Providing & fixing in position 460 mm deep storage / Wardrobe unit along with partitions etc with 1) sides,top,bottom shelves made out of 19 mm marine plywood 2)6 mm thk. marine ply backing panels 3) Shutters made out of 19 mm thick block board & 6 mm thick teakwood leaping with egde moulding of approved profile and additional moulding as per drawing or instruction of Arichtect if any shall be provided in all exposed ply edge surfaces & be finished with melamine polish / PU coating.4) Finish 1mm thk laminate inside & out side as per below mention. 5) hardwares such as heavy duty hinges of size 100 x 19 x 25 mm, brass body locks (Elpro make) with extra large group key of approved quality, magnetic ball catchers, handles of dia 12mm x 128mm, towerbolt 150mm etc. All exposed woodwork to be finished with 3 coats of melamine polish / PU coating & all internal surface finished with approved 1 mm thk laminate. All as per detailed drgs and instructions of EIC / Architect. Size in front elevelation will be measured for payment.

Low height storage with laminate finish (LST)

Over head storage laminate finish

Full height storage with laminate finish (FST)

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :

Size 50x12 mm

Size 50x20 mm

SIZE 15 X 15 MM

SIZE 25 X 50 MM

Doors & Windows Woks

Providing and fixing best quality superior Indian teak wood frame for doors, windows and ventilators including all moulding, rebating, jointing, hold fasts of MS flats of minimum size 20 x 3 mm, having length of 225 mm for doors & 150 mm for windows and finishing with 3 coats of French polish or one coat of primer and synthetic enamel paint in two coats as directed etc. complete.

Single shutter 35mm thk Flush Door both side Laminate -

Providing & fixing 35mm thk. Phenol bonded Flush door finish with 1.5mm thk. Laminate on both sides as per approved pattern. All edges should finish with teak wood lipping with melamine polish. All complete as per instructions & approval of EIC. Note: The rate of all doors shall include all hardware such as door handles, hinges, door closures/floor spring, dead lock, PVC door buffer, door stopper, latches etc. as required.

Single shutter 35mm thk Partly Glazed Partly Solid Door both side Laminate -

Providing & fixing door in position Partly Glazed Partly Solid door both side laminate made up Phenol bonded of 35 mm thk approved flush door of approved size & 12 mm toughened glass approved beading, grooves, approved moulding including necessary hardware, approved adhesive, fitting & fixture Handel, Lock, Floor Spring/door closer PVC door buffer, door stopper, latches etc. melamine polish to all exposed surfaces etc complete as per detail drawing as specified & as directed by Engineer-incharge.

Extra for louvers

Extra for if wooden louvers are provided in the bootom / top of flush door shutters approx 0.2sqm (overall area of door shutters to be measured).

Providing and fixing in position--------------aluminium openable window of any size as per detailed drawing and as directed by Engineer incharge with all necessary alluminium sections including necessary fixtures, mosquito net and fastening with 5mm thick clear float glass etc. complete.

coloured anodised

12mm thk Double / Single Leaf Glass Door

Providing and fixing in position 12 mm thick Toughened Fully Clear Glass Door by using various glass patch fittings to be fixed with necessary fittings on the ceiling duly finished without giving any load on the false ceiling by using necessary hardware what ever necessary and required numbers to complete the job in all respect. Rate including cost of door with approval hardware such as patch fitting lock, handle, Floor Spring of approved make. Contractor is advised to submit working drawing with details patch fitting, sizes of glass panels etc and take approvals of consultants before execution of works. complete as per detail drawing, as specified and as directed by Architect.

Chiken Mesh Jalli

Providing and fixing chicken mesh jalli with all hardware and fixing material to fix the jalli on every surface etc complete as per direction of Engineer - in - charge.

Compactors Works

Mobile System will consist of: Size 2550mm H X 800mm D X 1830mm W 1) Single Static Drive Cover Unit 2 Bay… 01 No. 2) Twin Mobile Drive Unit 2 Bay…………03 Nos. 3) Single Last Drive Cover Unit 2 Bay… ..01 No. 4) 13 Ft. Rails …………………………… 01 Pair 5) Each face of the Units will have 6 Shelves Levels, Dismantle & all Shelves levels adjustable will be provided. (Knock Down Systems). 6) Each Mobile Unit will have a Mechanical Assisted drive. 7) Each component of the system will be treated with rust preventive treatment and will be POWDER COATED for better finish. 8) The price for the complete system Inclusive of Delivery and Installation will be considered

Mobile System will consist of: Size 2550mm H X 800mm D X 2400mm W 1) Single Static Drive Cover Unit 2 Bay… 01 No. 2) Twin Mobile Drive Unit 2 Bay…………03 Nos. 3) Single Last Drive Cover Unit 2 Bay… ..01 No. 4) 13 Ft. Rails …………………………… 01 Pair 5) Each face of the Units will have 6 Shelves Levels, Dismantle & all Shelves levels adjustable will be provided. (Knock Down Systems). 6) Each Mobile Unit will have a Mechanical Assisted drive. 7) Each component of the system will be treated with rust preventive treatment and shall be POWDER COATED for better finish. 8) The cost of the complete system Inclusive of Delivery and Installation will be considered

Miscellaneous Works.

Soft Board

Providing and fixing in position 12mm thick Soft Board paneling on partition surface including fabric cover, wood beading finished with melamine polish of approved shade etc. complete as per detail drawing, as specified and as directed by Architect/Enginner In Charge..

wall paper

Providing, fixing, applying by Company Trained Technicians, premium Wall Covering (Wall Fabric), as per details in attached specifications, or as per detailed specifications and colours attached, or approved equivalent, of approved colour, texture and design, including base and sub-base preparation(on top of existing P.O.P surface), all complete, in a neat and workman like manner, as per directions of Engineer-In-Charge.

Basic

Graphic

Providing,aupplying,fabricating and fixing panel of aluminium composite panel cladding in approved shape made out of 4 mm thick ACP sheet material consisting of 3mm thick FR grade mineral core following NBC part IV Fire and life safety (having 2 hours fire resistance in accordance to ASTM E119-12 and BS476 part 6 and 7 class O) sandwitched between two aluminium sheets (each 0.5 mm thick of AA 5005/AA3105 grade) The aluminium composite panel cladding sheet shall be coil coated with kynar 500 based PVDF/ Lumiflon based fluropolymer resin (having 70:30 ratio of PVDF and acrylic) coating of approved colour and sg=hade on top face and polymer (service) coating of bottom face as specified using stainless steel screws,nuts,bolts,washers,cleats,weather silicon sealent,backer rods etc .overall weight of the ACP shall not be less than 7.5 kg/sqm

Vinyl Lettering for Logo Board

Using 3M Vinyl of 1mm thickness for logo on ACP as per drawing provided and direction by engineer incharge.

Plants for office

Painting/Picture frames

Pelmet

L - shape PELMETS / Jamblining : (upto 300 mm wide)

Supplying, Providing & fixing in position of required size pelmets / jamblining made out of 19mm thick marine plywood finished with approved finish mention below and 3 coats of French polish for inside surface as per the direction by Architect. Item to be completed in all respect as per the drawing & instruction from Architect.

1.5 mm thk Laminate Finish

Providing & arranging in position dust bins out of perforated (min Size 350 mm dia x 400 mm Height). Item to completed in all respect as per drg & directions.

3M Frosted Film

Supply & Installation of 3M Crystal Glass film Frosted/DUSTED/ effect with approved artwork, cut using digital plotter. Self-adhesive, bubble-free installation to be done on clean glass , by Authorized Installers only.3M Architectural Markets. 3M interior Warranty for a period of 5 years for interior application.

Providing and Fixing Singnages/Name plates in SS engraving as per approved design and shade for the fixed location

Providing and Fixing Singnages/Name plates acrylic with vinyle cutting letter as per approved design and shade for cabin

12mm thk Fix Glazed Partition

Providing and fixing glazed partition made out of 12 mm thk clear toughened glass with designs pattern as shown in drawing. Glass should fixed with required size of Silicon, adhersive, teakwood / wooden beading which finished with 3 coats of melamine polish / adhesive or any other fixing material to complete the works. Rate including cost of glass edge maching.

Plumbing Works.

Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing stainless steel sink of size 600 x 510 x 200 mm incluidng coupling, outlet pipe, elbow and other necessary fitting, finishing etc. complete.

Providing and fixing C.P. Angular stop cock with wall flange Jaquar make or equivalent continental (CAT.NO. CON-059) including necessary sockets/union nut etc. complete.

Providing and fixing C.P.Two way BIB cock jaquar make or equivalent continental (CAT.NO. CON-041) including necessary sockets/union nut etc. complete.

C.P.Toilet paper holder of approved make and as per EIC. (Jaquar- AHS-1553)

Providing and fixing inset type porcelain soap dish with all types of fixtures including labour charges including transport charges etc. complete.

Providing and Fixing of Mirrors in Toilets of approved Indian quality, copper plated with 10 mm thick plywood backing in the masonry etc. complete.As per direction of Engineer - in - Charge.

Providing and fixing Stainless steel towel rod with 20 mm diameter pipe in bathrooms and wherever necessary manufactured as per best engineering practice or as per I.S. wherever applicable with necessary materials and labour cost etc. complete. Upto 1200mm length.

Providing and fixing in position Hand dyrer as per instructions from EIC/Architect (Jaquar- HDR-SAP-M99ACS)

Providing and fixing in position Double coat hooks as per instructions from EIC/Architect (jaquar - ACN-1161N)

Providing and fixing C.P. Pillar cock for Table top Wash basin inclusive of all its fixtures and pipes. Complete. (Jaquar LYR-38021)

Providing and fixing C.P. sink cock for steel sink inclusive of all its fixtures and pipes. Complete. (Jaquar DRC-37347S)

Providing and fixing soap dispenser for Wash basin inclusive of all its fixtures and pipes. Complete. (Jaquar ACN-1135N)

Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete. (The contractor shall give 3 yrs guarantee bond for payment)

Providing and fixing 15 mm diameter PVC Aqua kraft type Supreme make or equivalent make super jet spray with flange 2 in 1 faucet 1.50 metre long including all accessories etc complete

Providing and fixing European type wall-hung white water closet of with push valve concealed type with cover plate 32mm size of JAQUAR MAKE SERIES FLV-1095 including conclealed Flush tank, soil pipe ,vent pipe up to outside face of wall ,100mm dia. G.I. plug bend inlet pipe all fittings, cuttingand making good walls, floors etc. complete.

Providing and fixing Water less Urinal with all fitting and accessories required to complete the works etc complete as per direction of EIC.

providing and fixing oval type over counter wash hand basin of 16 inch x 22 inch size and of special colour shade having telephonic black / coloured granite of 180 mm thick stone black kadappa framework including chromium plated coupling bottle - Trap using CERA company or equivalent oval type wash basin model no 3448 as per detailed drawing or as directed by engg incharge etc complete. (Counter size 1.20 m x 0.60 m)

Providing and fixing 15 cm rigid PVC Nahani trap including PVC grating ,bend,connectingpiece of UPVC pipe up to the outside face of wall ,making the good damaged surface and testing etc. complete ( Prior approval of sample and brand by Ex. Engr. is necessary before use)

Providing, laying and fixing P.V.C. pipe of 40mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing, laying and fixing P.V.C. pipe of 75mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing, laying and fixing P.V.C. pipe of 110mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing screw down for 20 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete.

Providing and fixing screw down for 25 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete.

Dismantling of Existing Sanitary CP Fittings, Plumbing Pipes, Drainage Pipes, Valves etc. Note. Visit Site while quoting

Aluminium / UPVC / PVC / GI Gutter

Providing and fixing gutter of above material 120 cm wide with all the fixture and accessories required to complete the works etc. complete as per direction of EIC.

Providing and fixing H.D.P container Syntexor alike one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery upto destination hoisting and fixing of accessories such as inlet, outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 liters

Electrical Works.

Lighting Distribution Board

Supplying and erecting single pole and neutral distribution board (SPNDB) with door surface/flush mounted with 2 ways for incoming and 10 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB

Supplying, fixing and commissioning 2 pole,RCBO (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 6/10/16/20/25A, as per specification no SWRCCB/RCBO

Supplying, erecting & marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification no. SWSWR/MCB

Power Distribution Board

Supplying and erecting triple pole and neutral distribution board (TPNDB) surface/ flush mounted suitable for SPMCB of 24 ways on iron / GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification no. SW-SWR/MCB

Providing, erecting and commissioning 2 pole RCCB only of electromagnetic type with 30/100/300 mA sensitivity and having capacity of 16/ 25A complete as per specification no. SWRCCB/RCCB

Supplying, erecting & marking SPMCB 6A to 32A, C-series (for motor/power) in provided distribution board as per specification no.SW-SWR/MCB

UPS Distribution Board

Supplying and erecting triple pole and neutral distribution board (TPNDB) surface/ flush mounted suitable for SPMCB of 24 ways on iron / GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification no. SW-SWR/MCB

Providing, erecting and commissioning 2 pole RCCB only of electromagnetic type with 30/100/300 mA sensitivity and having capacity of 16/ 25A complete as per specification no. SWRCCB/RCCB

Supplying, erecting & marking SPMCB 6A to 32A, C-series (for motor/power) in provided distribution board as per specification no.SW-SWR/MCB

Air Conditioning Distribution Board

Supplying and erecting triple pole and neutral distribution board (TPNDB) surface/ flush mounted SP /TP MCBs of 12 ways on iron / GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking TPMCB 6 A to 32A in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, C-series (for motor / power) in provided distribution board as per specification no.SW-SWR/MCB

Main Distribution DB

Supplying and erecting triple pole and neutral distribution board (TPNDB) surface/ flush mounted SP / TP of 24 ways on iron / GI frame (vertical busbar type) as per specification no. SWSWR/ MCBDB

Supplying, erecting & marking FPMCB 40A to 63A in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, C-series (for motor/power) in provided distribution board as per specification no.SW-SWR/MCB

Supplying, erecting & marking TPMCB 6 A to 32A in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking TPMCB 40A to 63A in provided distribution board as per specification no. SW-SWR/MCB

LT Cables

Supplying, erecting & terminating XLPE armoured cable 3½ core 25 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 4 core 16 sq. mm. copper conductor with continuous 5.48 sq. mm. (12SWG) G.I. earth wire complete erected with glands & lugs, on wall/trusses/ pole or laid in provided trench/ pipe as per specification no.CB-LT/CU

Supplying, erecting & terminating XLPE armoured cable 4 core 10 sq. mm. copper conductor with continuous 5.48 sq. mm. (12SWG) G.I. earth wire complete erected with glands & lugs, on wall/trusses/ pole or laid in provided trench/ pipe as per specification no.CB-LT/CU

Supplying, erecting & terminating XLPE armoured cable 4 core 6 sq. mm. copper conductor with continuous 5.48 sq. mm. (12SWG) G.I. earth wire complete erected with glands & lugs, on wall/trusses/ pole or laid in provided trench/ pipe as per specification no.CB-LT/CU

Supplying, erecting & terminating XLPE armoured cable 4 core 4 sq. mm. copper conductor with continuous 5.48 sq. mm. (12SWG) G.I. earth wire complete erected with glands & lugs, on wall/trusses/ pole or laid in provided trench/ pipe as per specification no.CB-LT/CU

Supplying, erecting & terminating XLPE armoured cable 3 core 2.5 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/trusses/ pole or laid in provided trench/ pipe as per specification no.CB-LT/CU

Supply, handling, laying effecting proper connections testing and commissioning of following sizes of 1.1 KV grade XLPE insulated FR Aluminium /Copper conductor cables laid over MS supports cable racks or fixing on walls including clamping the cable to supports in an approved manner as required complete with Copper earthing as specified for continuous earthing along with cable. All complete as required and as per final instruction as given by Owners/ Consultants. and as per Technical specifications.

1C x 4 Sq.mm.,XLPE Copper Conductor Flexible Cable

Supply and making terminal joints for the following sizes of 1.1KV grade XLPE Insulated armoured / Unarmoured Aluminium/Copper conductor cables including providing heavy duty tinned coper terminal lugs, crimping type, insulation tape, heavy duty single compression type brass glands effecting terminal connection to the equipment/Panel complete as required as per final direction and approval of the Owner/Consultant.

1C x 4 Sq.mm.,XLPE Copper Conductor Flexible Cable

Cable Tray

Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 200 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.

Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.

Mains in PVC Conduit (WG-MA/PC)

Supplying & erecting mains with 2x1.5 sq.mm. and earth wire 1.5 sq.mm FRLSH PVC copper wire, in HMS PVC conduit min. 20mm dia as per specification No: WG-MA/PC.

Supplying & erecting mains with 2x2.5 sq.mm. and earth wire 1.5 sq.mm FRLSH PVC copper wire in HMS PVC conduit min. 20mm dia. as per specification No: WG-MA/PC.

Supplying & erecting mains with 2x4 sq.mm. and earth wire 2.5 sq.mm FRLSH PVC copper wire in HMS PVC conduit min. 20mm dia, as per specification No: WG-MA/PC.

Supplying & erecting mains with 2x6 sq.mm. and earth wire 4 sq.mm FRLSH PVC copper wire, in HMS PVC conduit min.20mm dia, as per specification No: WG-MA/PC.

Supplying & laying HMS PVC conduit 20 mm dia. With necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying & laying HMS PVC conduit 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Bunch of Wires (WG-MA/BW)

Supplying & erecting mains with 2x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WGMA/BW

Supplying & erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WGMA/BW

Supply & Laying of Armoured FRLS Power Cable : 3 Core x 1.00 Sq.mm PVC insulated ,PVC Sheathed Cablelaid on Surface , or in cable trays, or in GI Conduits as per site requirements with GI saddles & spacers with termination lugs, cable tags etc.

Supply & Installation of 32 mm GI Conduits with GI Saddle & Spacers

Point Wiring (WG-PW)

Point wiring for light/fan/bell in 20 mm ISI marked HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire with flush type switch and required accessories as per specification No: WG-PW/SW

Point wiring for light/fan/bell in 20 mm ISI marked HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire with flush type switch and required accessories as per specification No: WG-PW/SW (8 Meter)

Point wiring for light/fan/bell in 20 mm ISI marked HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire with flush type switch and required accessories as per specification No: WG-PW/SW (12 Meter

Secondary point wiring for additional light/ bell point, concealed type in min 20 mm PVC conduit with 1.5 sq.mm. (2+1E) FR/FRLSH grade copper wires with required accessories as per specification No: WG-PW/CW

Modular switches and Accessories

Supplying and erecting ISI mark modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type switch 16A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type 3 pin 6A multi sockets with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type T.V. sockesingle outlet, duly erected on provided plate and box witwiring connections complete.

Supplying and erecting ISI marked modular type telephone socket one gang with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type computer jack RJ 45 with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 1 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background..

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 4 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 8 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 16 / 18 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

CEILING FANS & EXHAUST FANS

Supplying and erecting five star rated energy saving Ceiling fan 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Supplying and erecting ISI mark modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting fan hook box of 10 mm M.S. round bar bounded to the R.C.C. bars upto 50 mm length each side and pierced through a 16 S.W.G. thick aluminium/M.S. Bowl 100 mm dia.or equivalent square size and having depth upto 75 mm complete erected with duly painted by one coat of red oxide paint and two coats of paint erected in position and without any leakage of slurry of cement concrete on either side of the box and positioned to the bottom level of the slab.

Supplying and erecting ‘B’ grade G.I. pipe / M.S. pipe down rod duly painted for fan complete erected with PVC three core flexible cable 1 sq. mm copper PVC wire.

Supplying and erecting fresh air cum exhaust fan of light duty 250 V A.C. 50 cycles 300mm. 1400 RPM rust proof body & blades, wire mesh, duly erected in an approved manner.

Floor Trunking

Supplying and embedding of following sizes of under floor trunking made out of 1.6 mm thick Hot Dip Galvanised Steel sheet having below mentioned compartments including Jointing sleeves, floor fixing supports, chipping and levelling that portion of the floor etc in the floor / in recess etc as per specifications complete as required.

50mm x 38mm (Legrand 6895 00)

75mm x 38mm (Legrand 6895 01)

100mm x 38mm (Legrand 6895 02)

150mm x 38mm (Legrand 6895 02)

Supplying and fixing of following sizes of under floor junction boxes made out of 2 mm thick pre-galvnaized sheet steel, top cover with 2.5 mm thick pre-galvanized steel plate alongwith changeover fly-overs including chipping and levelling that portion of the floor etc as per specifications complete as required.

150mm x 150mm x 65-90mm (Legrand 6896 10)

225mm x 225mm x 65-90mm (Legrand 6896 11)

Data & Telephone Networking

Supplying & installing UTP networking cat-6 cable suitable for LAN / WAN Computer net-working as per specification No. WG-COC/NC

Supplying and fixing 1 meter length, UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Supplying and fixing 3 meter length, UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Supplying erecting VGA cable to be laid in Provided conduits and Terminating as per specifications having 15mtr cord length with male/female VGA connectors as per requirements complete.

Supplying & installing HDMI cable low voltage grade as per specification as per specifications having 10 mtr cord length with male/female 19pin HDMI connectors as per requirements complete.

LIGHT FITTINGS

Supplying and erecting LED square / circular 5 to 8W down lighter having pressure die-cast aluminium housing, opal translucent cover, mounting arrangement with board for surface type or spring loaded mounting clips for flush type complete

Supplying and erecting LED square / circular 13 to 15W down lighter having pressure die-cast aluminum housing, opal translucent cover, mounting arrangement with board for surface type or spring loaded mounting clips for flush type complete.

Supplying and erecting square shaped CRCA /die-cast aluminium powder coated housing LED panel light (slim edge-lit) 600x600mm suitable for 36 W-40W with provision for plane front frame with translucent cover fixed to the housing complete.

Supplying & erecting LED 20W tube light fitting (4 feet) with aluminium housing, heat sink, integrated HF electronic driver complete.

Supplying and erecting LED flexible strip light 5m length upto 25W conforming IP 65 of any colour with driver complete.

Supplying and erecting LED Mirror Light with integrated driver including 14W to 18W lamp with polycarbonate housing and opal diffuser to be fixed above mirror or as required on clamps complete.

Supplying and erecting 12 Watts LED Bracket Light to highlight paintings. (HYBEC HLA-3601)

Supplying and erecting 10 Watts LED Wall Washer Light complete as directed by Architect.

Supplying and erecting street light Wall bracket made from 25 mm. dia ‘B’ class G.I. pipe 1.2 m in total length complete as per specification no. FG-BKT/WB

Supplying and erecting flood light luminaries suitable for 70WH.P.S.V. lamp complete with accessories on provided bracket as per specification no. FG-ODF/GSL

Supply, Installation & Testing of Motion sensors for washroom and allied areas-PIR occupany sensor.Make:Philips,Wipro or approved equivalent.

Earthing

Supply, Installation, Testing and commissioning of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete. Specification no. EA-MOBI

Supplying and erecting copper strip of required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification No EA-EP..

Supplying and erecting GI stripof required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification NoEA-EP.

Supplying and erecting G. I. Earth Wireof high purity of different sizes used for earthing or any other purposes on wall with necessary G. I. Clamps fixed on wall/cable/ conduit with screws in an approved manner.

Online Uninterruptible Power Supply

Supplying & erecting on line UPS pure sine wave of 6 kVA capacity/as per site requirement complete with standard features,along with necessary SMF batteries for 30 mins battery backup, as per specification no. AP-UPS

Generators

Supplying, erecting and commissioning of diesel generating set with alternator of 30 kVA output continuous rating, 3 phase, 415 V,50c/s 0.8 p. f. A.C a totally enclosed air cooled / liquid cooled multi cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, selfexcited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 %. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads with standard control panel comprising meters, switchgears, indicators connected with suitable wires/cables, the complete set enclosed in composite acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA Sheet, sound absorbing material to restrict sound level upto 75 dB at 1.0 m, provided with first filling of oil, diesel etc. as per specification no.GEN-DG

Auto Mains Failure Panels (AMF Panels)

Supplying, erecting, testing and commissioning of Microprocessor based AMF panel suitable for diesel generating set of above 25 kVA upto 35 kVA capacity Single/Three phase, 230/415 Volts, 50Hz A.C. with all standard features, safeties etc as per specification no. GEN-AMF.

Removing old electrical fixtures of all types i.e. lights, fans, detectors, exhaust fan,switchboards etc. including its wiring and stacking of serviceable material and disposal of unserviceable material with all lead and lifts.

Fire Detection System

Supplying, installing, testing and commissioning of 2 Zones Microprocessor based addressable fire alarm control panel (FACP) with standard accessories complete as per specification no. FF-FAAS/FACP

Supplying, installing, testing and commissioning optical type smoke detector complete on box as per specification no. FFFAS/SD

Supplying, installing, testing and commissioning heat detector complete on box as per specification no. FF-FAS/HD

Supplying, installing, testing and commissioning manual call point (Pill box) with break glass push button in metal enclosure complete as per specification no. FF-FAAS/MCP.

Supplying, installing, testing and commissioning hooters with CRCA enclosure complete as per specification no. FF-FAAS/HTR

Supplying, installing, testing and commissioning FR, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CBLT/CU

Dismantling of existing smoke detectors, Hooters, Wiring, etc. Note. Review site while quoting

HVAC Works.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 12.7 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultraviolet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 9.5 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV /VRF air conditioning system.

supply, installation and comissioning of client provided air conditioning system

Providing vaccumising the airconditioner system to 200 micron and charging with R-410A/R32 refrigerant for air conditioning unit.

Providing annual comprehensive maintenance contract for 2 TR split/window air conditioning unit complete as per terms and conditions. Job includes 1)quarterly servicing 2) on call repair 3) replacement of all spares within 24 hours 4) sending standby manpower for VIP movement. The job exclude sheet metal work and plastic material.

Providing annual comprehensive maintenance contract for 3TR to 4.5 TR split/tower/window air conditioning unit complete as per terms and conditions. Job includes 1) quarterly servicing 2) on call repair 3) replacement of all spares within 24 hours 4) sending standby manpower for VIP movement. The job exclude sheet metal work and pastic material.

Drain U-PVC OR GI Pipe Fully Insulated with 9 mm rubber nitrile insulation (Include core cutting, tray and any item to complete the work)

Supply and installtion of wall mount type stand for outdoor unit of suitable thickness and section complete as required.

Solar Panel System Works for 30 KW.

SOLAR ROOF

Providing, Supplying Solar roof of Polycrystalline 325 wp Ip67/ IEC61215-61730 Class A Fire Rated Modules etc complete as per direction of Engineer in charge.

MS Structure

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

25 KV Solar Inverter

Providing, supplying 25 KV solar inverter as per direction of Engineer in charge.

1C, 4sq.mm, Double Insulated Copper cable with all required accessories like MC & FMC , Cable ties, connectors etc

DCJB's or DCDB

JB's 2 Nos( 10IN & 10OUT-50KW)

AC Cable AL Armored

3.5C, 50Sq.mm , AL Ar. Cable- 50KW ( Inverter to Existing

3.5C, 25 Sq.mm , AL Ar. Cable- 20KW ( Inverter to Existing

AC Distribution Panel Board

IP-54 rated enclosures with all switchgears, 100A ,4P MCCB- 50Kw and 63 A,4P MCB-40Kwp

Cable tray of Suitable sizes and type with all acessories and required supports

Earthing System

17.2 mm Thick 3 meters Long Cu Bonded with Carbon Compound

Conventional Model- Type IV (1 meter Copper rod with Sikes and 3 Meters height GI Pipe)

Each set Per Inverter

Fixing the Solar Panel on Roof Grid

Civil Works

Minor Civil works Only

Approvals & Liasioning

Net Meters & CEIG (Initial and Final Approval)

Fire Extinguishers, Sand buckets, Danger Boards, Radium Sticker for marking

Installation & Commissioning

Module Interconnection, Connections of ACDB

M/S P.K.Enterprises