Renovation of Ambedkar Chaupal at Rangpuri village in Bijwasan Assembly Constituency AC-36.

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.15.7.4 In cement mortar

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-lll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Kota stone slab flooring over 20 mm (average) thick base laid over and inted with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor III level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-lll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor III level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources).

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts

Edges of slabs and breaks in floors and walls Under 20 cm wide

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo -Mechanically Treated Bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor III level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:3 (1 cement :3 coarse sand)

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. ( DSR No- 8.12.1 )

Granite stone work gang saw cut (polished and machine cut) of thickness 18 mm for wall lining (veneer work), backing filled with a grout of 12 mm thick average in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately). Granite of any colour and shade Area of slab above 0.50 sqm.

Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides Red sand stone - exposed face fine dressed with rough backing. 30 mm thick

Providing and fixing carbon steel galvanised ( minimum coating 5 micron)dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. 10 x 120 mm

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes.

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.1.00 mm thick with zinc coating not less than 275 gm/m².

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Finishing walls with water proofing cement paint of required shade : Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat.

12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge. With cement mortar 1:4 (1cement: 4 coarse sand)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown bitumen 85/25 or 90/15 onforming to IS : 702 applied hot @ 1.45 Kg per square metre of area for each course, second course of roofing felt type 3 grade-I (hessian based self finished bitumen felt) and fourth and final course of stone grit 6 mm and down size or peasized gravel spread at 6 cubic decimeter per square metre, including preparation of surface but excluding grading complete with : Bitumen felt (hessian base) type 3 grade I conforming to IS : 1322

Renewing acrylic sheet panes 3mm thick, with silicon putty and nails wherever necessary.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing :4.2.3 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.75 mm diameter

Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc. : 100 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm bend

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular tank per

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 18.49.1 15 mm nominal bore

Providing and fixing PTMT liquid soap container 109 mm wide, 125mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 20 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 32 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 40 mm dia nominal bore

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 20 mm dia nominal bore

Providing and fixing brass stop cock of approved quality : 20 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required.Group C

Wiring for light point/fan point/exhaust fan point/call bell point with 1.50 Sq.mm.FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit with piano type switch, Phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc as required.(Group C).

Wiring for circuit/sub main wiring along with earth wire with the following size of PVC insulated copper conductor, single core cable in surface/recessed PVC conduit as required. 2 x 4 sq.mm + 1 x 4.00 sq.mm earth wire.

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following sizes of FR PVC insulated copper conductor single core cable in the existing surface/recessed steel/PVC conduit as required. (a). 3 x 2.5 sq.mm.

3 x 4 sq.mm.

box/ cover including connections etc. as required. A). 5/6 amps switch

15/16 Amp switch

3 pin 5/6 amp. Socket out let

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, PVC box alongwith modular base & cover plate for modular switches in recess etc as required. a).3 Module (100mmX75mm)

4 Module (125mmX75mm)

Supplying and fixing stepped type electronic fan regulator on the existing switch box including connection but excluding.

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required.200 mm X 250 mm X 60 mm deep

Supplying and fixing of following sizes PVC channel along with all accessories on surface at the wall and king good the same in case of recessed as required.a) 25 mm x 45 mm size.

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.2 Pair

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way, Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)8 way (4 + 24), Double door

Single pole and neutral

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. a). Single pole

Triple pole

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supplying installation testing and commissioning of energy efficient ceiling, /wall/guarder mounting prewired fluorescent tube light fitting suitable 36/40 watt lamp. the fitting shall be made of box type powder coated CRCA sheet complete with electronic ballast, lamp & holder duty wired up ready for 240 volts, single phase, 50Hz AC supply confirming to IS: 10322 as per quality requirement. Fitting shall be provided with all accessories and mounting arrangement as required, including connection with 1.5 sqm. Mm FR PVC insulated copper conductor single core cable and earthing etc. (Make Surya, Bajaj, Havells, Philips Wipro) or as approved by the Engineer-in-charge. a) 1 x 40 watt

2 x 40 watt

Supplying installation, testing and commissioning of 1200 mm sweep AC electric ceiling fan capacitor type with double ball bearing complete with down rod, canopies, shackles, blades but with out regulator suitable for operation on 230/240 volts, 50 Hz single phase AC supply including wiring the down road of standard length up to 1 mtr. With 2x1.5 sq. mm PVC insulated copper conductor with fan sheet etc. as required (Make Bajaj, Orient, Usha, Havells polar).

Supplying installation, testing and commissioning of bulk head/ceiling light fitting suitable for 60/100 watt GLS lamp complete with Lamp and accessories such as glass, wire guard, lamp etc. including connection as required (Make Surya, Baja, Wipro, Philips, Havells) or as approved by the Engineer-in-charge.

Providing and fixing precast reinforced cement concrete bench of over all size 1500 mm x 450 mm x 1000 mm, the bench consist of 02 nos. L-shape base sport in cement, thickness 100 mm back height 1000 mm front height 450 mm base width 620 mm as per sketch and 05 nos. reinforced concrete planks in red colour of sized 1500 mm x 100 mm x 50 mm and 01 nos. RCC planks of size 1500 mm x 200 mm x 50 mm by using M-30 grade of concrete using vibro compaction process, bench top and back planks are treated with special anti-corrosive water proof coating so as to make surface glossy and water proof including transportation, erection all part are jointed to gather with galvanized nuts and bolts of suitable size. All bolts are sealed after assembly. (benches shall be of KK mark or approved by Engineer-in-charge).

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Supplying, installation, Testing and commissioning of continuously tapered multifaceted and polygonal cross section 16mtr high mast system hot dip(galvanized) with wind velocity as per IS 875 part-3 as per detailed specification attached with following Make Bajaj, Philips, G.E., Volmont.a) 2 sections having suitable sectional length with slip joints between various sections without any circumpherial welding.b ) Double drum winch with separate handle for manual operation of winch with a torgue limiting device for safe checking of carriage. c) Raising/lowering type lantern carriage designed to carry 9 Nos. luminaries control gear box, junction box and top pulley assembly with weather proof cover. d) Necessary suitable length for lowering and raising of lantern carriage of stainless steel wire ropes of 7/19 construction and with suitable size of multi core flexible copper power cable. e) Hinged service door in base section base plate earthing terminal. f) Lightening conductor final made of 25mm dia 300mm long G.I. tube having single prong.g) Integral single power tool (electrical) for lowering & raising of high mast.

Providing and laying the RCC foundation suitable for erection of 16mtr high mast as per manufacturers recommendation including excavation, casting of foundation anchor plate, templates and foundation bolt manufacturer from special steel along with nuts, washers etc. R.C.C. work 1:1.5:3 (1 cement” 1.5 coarse sand: 3 graded stone aggregate 20mm nominal size) with material, labour and reinforcement with size of footing 2.10x2.10x0.20m laid over 1:4:8(1 cement:4 coarse sand:8 graded stone aggregate 40mm nominal size) and foundation pedestal of size 0.90x0.90x2.00m or as per approved drawing complete as required.

Supplying and laying double walled corrugated (DWC) High Density Poly ethylene (HDPE) pipe of 50/38 size having corrugation on the outer wall and plain surface on inner wall confirming

to IS 14930 (Part II) below the ground level excluding excavation refilling the trench etc. as per specification etc. as required

Providing and fixing of 200 watt LED flood light (IP66) with aluminium housing and heavy heat sink, including toughned glass (Surya).

Supplying, installation, testing and commissioning of feeder pillar of suitable size made from 2mm thick CRCA sheet dust and varmin proof duly phosphatized and painted inclusive of suitable size 4 strip Bus bar complete with inter connection, inter earthing and providing and fixing below noted accessories.(M/R) Timer 24 hours = 1 No. TPN MCCB – 63 Amp = 1 No. MCB- 6 to 32 Amp = 10 Nos. Power contactor = 1 No. Indicator light = 3 Nos. Reverse switch = 1 No.

Supplying of PVC insulated and PVC sheathed (General purpose) XLPE/armored multi core cable with standard aluminum conductor suitable for working voltage upto and including 1100 volts confirming to IS 7098/Part/1988 with amendment slips upto date. Size 4x25sqmm. (M/R)

Laying and fixing of one number PVC insulated & PVC sheathed /XLPE power cable of 1.1 KV grade of size not exceeding 35sq. mm clamped with 1mm thick saddle on wall surface, as required.

Laying and fixing of one number PVC insulated & PVC sheathed /XLPE power cable of 1.1 KV grade of size direct in ground including excavation and refilling the trench etc. as required but excluding sand cushioning and protective covering upto 35mm.(7.3.1)

Earthing with G.I. earth pipe 4.5 mtr long, 40mm dia including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required.5.2

Supplying and laying 6 SWG G.I. wire at 0.50metre below ground level for conductor earth electrode including connection, termination with G.I. thimble etc. as required. 5.7

Providing and fixing 3 Seater Stainless Steel benches with backrest made out of SS 304 Grade materials, overall dimension 1450x890x450 mm, sheet thickness will be 1.5mm and pipe thickness will be 2.0mm and dia. 38 mm. Turret punching or Laser cutting will be used for perforation.(weight approx. 40 Kg)