SPECIAL REPAIR TO ROOF BLDG NO. P14 TO P19, 27 TO 34, 24 TO 26 OF RA LINE, REPAIR IN BLDG NO. P360, PROVN OF ME EQPT STORE ROOM 4.00 X 6.50 MTR,TOILET BLOCK OF SRI BLDG AND PROVN OF 40 X CEILING FANS FOR JCOS/ OR SINGLE LIVING ACCN AND MH ACCN OF 803

Amount

Demolition of plain cement concrete in any position including tar felt & cement mortar bedding etc from roof or sunken etc complete all and removing debris as specified and directed.

Demolition of mud in roofs, any thickness, including plastering and leaping ( whether full thickness removed or only a part thereof) & disposal of retrieved material where directed complete all as specified and directed. Note:- Removal of demolished material shall be measured & paid under respective item.

Dismantling of brick tiles or terracing tiles, single layer on roofs complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-0 12.5mm graded stone aggregate as in roof padding, roof kerbs, benching on roof slab and other similar works laid as per slop required finished even and fair complete all as specified and directed.

Taking down cement plaster on brick wall or stone wall etc including raking out joints hacking for key, scrubbing down with water etc complete all as specified and directed

M&L for 10mm thick plaster in CM 1:3, mixed with liquid water proofing compound over concrete surface of roof /chajja on cleaning of surface complete all as specified and directed. (Note : WPC to be measured and paid separately under appropriate item)

Cleaning the dust, dirt and any other foreign material from roof surface and applying a coat of bituminous primer @ 0.40 ltr / Sqm uniformly and primer shall be allowed to dry over night as conforming to IS 3384-1986 complete all as specified and directed.

M&L for Laying of minimum 3mm thick APP membrane of (reinforced with non-woven fabric polyester type wt not less than 150 gms/Sqm) & minimum weighing 3kg/Sqm shall be done using butane torch maintaining 100mm side overlap and 150mm end overlap, sealing all overlaps and bonded to the surface by fusing and bonding torch on method complete all as specified and directed. Note: All water proofing work shall be done as per manufacturer instruction and under supervision of manufacturer technical representative.

Supply only Liquid water proofing compound (ISI marked) complete all as specified and directed.

M&L for 40mm thick brick tiles laid over and including 20mm thick screed bed in CM 1:4 mixed with polymer based liquid water proofing additive @ 5 % by weight of cement or as per manufacturer's instruction and the joints of tiles shall be filled with CM 1:3 mixed with crude oil as per SSR-2009 (Part-I) on roof area and proper curing with water by ponding complete all as specified and directed.

All as per item No 10 but except tiles complete all as specified and directed. Note:- Tile obtained from dismantling shall be used.

Disconnecting existing water tanks of 500 to 1000 ltrs capacity setting aside (or lowering if required) and hoisting, reconnecting and re-fixing in same position after cleaning complete all as specified and directed.

S&F in repair rotational moulded polyethylene water storage tank of capacity 500 ltr (Cylindrical/vertical with closed top) double layer construction, ISI marked hoisted & fixed in position including dismantling of old tank and removing from site complete all as specified and directed.

S&F in repair rotational moulded polyethylene water storage tank of capacity 1000 ltr (Cylindrical/vertical with closed top) double layer construction, ISI marked hoisted & fixed in position including dismantling of old tank and removing from site complete all as specified and directed.

S&F in repair ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed 20mm bore minimum weight 210 gms complete all as specified and directed.

M&L for brick work using fly ash bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 etc complete all as specified & directed.

Removing building materials (mud phuska) from site etc to a distance of not less than 1 Km including loading unloading and stacking at the destination complete all as specified and directed.

M&L for preparation of newly plastered surface of wall with scrapping machine tools/electric hand grinder with wire brushes, sand papering and applying two coats of cement base paint including one coat of primer complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate as in chajja etc and the like with necessary form work complete all as specified and directed. Note:- Reinforcement & formwork to be measured & paid separately under respective item.

Use & waste of formwork to chajja, trough and similar item including edge etc rough finished complete all as specified and as directed.

M&L TMT bar 10 mm dia and over, cut to length, bent to shape required ,including cranking ,bending spirally for hooping for columns, hooking end and binding with and including mild steel wire and annealed not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Taking up or down 15 mm bore GI steel tubing and connections on (walls, ceiling, floors, etc.) including cleaning complete all as specified and as directed

Refixing old 15 mm bore GI steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed

S&F 15 mm bore GI steel tubing "medium grade" with all fittings and fixed to wall, floor and ceiling etc complete all as specified.

Taking up or down 20 mm bore GI steel tubing and connections on (walls, ceiling, floors, etc.) including cleaning complete all as specified and as directed

Refixing old 20 mm bore GI steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed

S&F 20 mm bore GI steel tubing "medium grade" with all fittings and fixed to wall, floor and ceiling etc complete all as specified.

S & F in repairs 110 mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to walls or floor or in trench complete all as specified and directed.

S & F in repair 110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

Demolition of cement concrete in ground floor and paving not exceeding 15cm thick below or above ground level unreinforced complete all as specified and directed. .

Demolition of Stone slabs and tiles laid dry and dry or pointed of any description or thickness in floors, aprons etc complete all as specified and directed. .

M&L for Glazed ceramic coloured tiles 7 to 8mm thick area of tile exceeding 0.18 and not exceeding 0.36 Sqm in skirting, dados, risers to steps, etc se and jointed in neat cement slurry, and pointed in coloured cement to match tiles over and including 10mm thick rendering or backing layer in cement mortar 1:4 complete all as specified and directed.

M&L for 18 to 20 mm thick machine cut kota stone flooring ,laid & jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing finished laid over and including 15 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for grinding, rubbing and mirror polishing of kota stone complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6 type C1 using 20 mm graded stone aggregate in plinth protection finished even and fair including necessary form work and cutting of joints using extra cement etc complete all as specified.

M & L for cement concrete 1:4:8 type D-2 , 40 mm graded aggregate in foundations, filling and mass concrete using 40 mm graded aggregate complete all as specified and directed

Demolition of brick work or stone masonry, built in cement mortar incl all quoins, pillars etc complete all as specified and directed

M&L for brick work using old size sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 etc complete all as specified & directed.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying 1-2 mm thick cement based wall care putty to achieve a smooth finish surface and apply two coats of oil emulsion distemper over a coat of primer complete all as specified and directed.

M&L for complete removal of existing plastered unplastered painted/ old painted surface by scrapping machine tool/electric hand grinder or removal of paint from wall surface completely from exposed brick/ plasterd surfaces and applying and painting two coat of oil emulsion distemper over a coat of primer over & including a layer of 1 mm thick cement based wall care putty in required shade on exposed brick wall/ plain wall surface as per manufacturer's specification etc including all tools, plants scaffolding, safety belts complete all as specified and directed

M&L for complete removal of existing plastered unplastered painted/ old painted surface by scrapping machine tool/electric hand grinder with wire brushes, sand papering and applying two coats of cement base paint over & including one coat of primer complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exc 1.50 Sqm but n. exc 4sqm each complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows & other Frames/ Chowkhat of size 65 X 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with mitre joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed. (Note: stainless steel butt hinges and necessary stainless steel screws shall be paid separately)

S&F for 18 mm thick 100% Solid PVC laminated board of required size comprising of virgin PVC resin of K Valve 57-60 (Suspension Grade), Calcium Carbonate and natural fibers ( Wood powders/rice husk/Wheat husk) and non toxic additives, made from Extrusion process WPC foam sheet Single extruded (Inner) with having minimum density not less than 650 kg/cbm having good screw holding capacity (Screw withdrawal strength of 2000 N (Face) & 1100 N (Edge), minimum Compressive of 50 N/mm2, Modulus of elasticity 850 N/mm2 and resistance of spread of flame of Class A category with property of being termite / Borer Free, water / moisture proof and Fire Retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces for kitchen cabinet shutter complete all as specified and directed. Note : Material test certificate and authentication should be provided by the manufacturing company.

S&F of Stainless steel auto closing hinges operable at 0 degree for kitchen cabinet shutters complete all as per specified and directed. Make: Hettich Cat part No.9281432 or any other make as approved by GE.

S&F of stainless steel handles 138 mm size for kitchen cabinet shutters complete all as per specified and directed. Make: Hettich : Cat part No.9113468 or any other make as approved by GE

S&F MS framed work as in doors frame, doors or gates of angle iron, door frame or other section with gusset plate, rails, braces etc complete, drilled for fixing of steel sheeting or other covering etc. to prepared for hanging or sliding with including either hooks and hinges, also fastening and fixing and similar work confirming to Fe 290 Gde-E-165 complete all as specified.

S&F 35 mm thick factory made 2nd class hard wood glazed and skeleton shutters, open repeated and prepared to receive glass, gauze etc (with sash bars) edges of framing plain, chamfered or rounded, fitted with cut and metered beads for securing glass etc, size of member of shutter as per specified in SSR part-I section 8,clause 8.24(a) and for door and fixed with chowkats, chemically pressure treated complete all as specified and directed.

Complete removal of mud phuska from roofs of any thickness and removing the waste material from site to a distance exc. 250m but not exc. 500m and deposited where directed including cleaning of surface complete all as specified and directed.

M&L mild steel work as in bands, straps, supports or stays for rain water, ventilating pipes including bolts, if required, hooks (stay) heavy for large gates, hooks and pintle hinges, large hasp and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans and similar articles conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F butt hinges extruded aluminium alloy with galvanised mild steel pin type B-21 of size 100mm complete all as specified and directed.

S&F 150mm long aluminium handle cast type anodized fixed with steel screw complete all as specified and directed

S&F aluminium anodised barrel tower bolts of extruded section 200 mm long complete all as specified & directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections suitable for use with pad lock complete all as specified and directed.

S&F 300mm, MS ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F 4.8 mm thick sheet glass ordinary quality in square n.exc 0.5 Sqm in each pane for new ventilator / window shutter complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 using (20mm graded stone aggregate) as in bed blocks for hold fast, coping erection of posts etc complete all as specified & directed.

S&F providing and fixing factory made UPVC white colour sliding window area not exceeding 2.00 Sqm each, three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm), sliding mesh sash (42mm x 57mm), sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2 mm thick galvanised steel frame (30mm x 18mm) 2 Nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system & stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and required accessories complete as per manufacturer's specification and directed. Note: (i) The unit rate quoted by contractor includes all connected accessories. (ii) Net Opening will be measured for payment purpose. (iii) Glass shall be measured & paid separately under respective item. (iv) Area not exceeding 2.00 Sqm each complete.

Dismantling wall and ceiling boards or insulation boards, any thickness, any description, including cover fillets complete.

S&F in repair 4 mm thick non asbestos fiber cement building board of 600x600 mm in size (HPSC E-classic) decorative finish fixed to aluminum /CGI frame work with hold down clips in false ceiling complete all as specified and directed.

S&F powder coated GI ceiling suspension system false ceiling grid of 600x 600mm size and 0.30 mm thick (MS galvanized (PPP CGS) with main tee, cross tee and wall angle grid hanging with 4mm dia Gl wire and roof fasteners or butterfly clips etc complete all as specified and directed.

S& F in repair hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified all as specified

S&F Mild steel conforming to Fe 290 (Gde - 165-E) in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete all as specified & directed.

Excavation over areas, not exceeding 1.5m deep and getting out in soft / loose soil complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming of soil in layers not exceeding 25 cm complete all as specified and directed.

Removing excavated soil material not exc 50 m and deposited where directed at a level n exc. 1.5m above the starting point all as specified and directed

M & L for Reinforced cement concrete design mix M-25 using 20 mm graded stone aggregates in foundations, footing, plinth beams, bases for columns and mass concrete complete all as specified and directed. Note:- Reinforcement to be measured & paid separately under respective item.

M & L for Reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregates) in columns, pillars, posts & struts complete all as specified and directed. Note:- Reinforcement to be measured & paid separately under respective item.

M & L for Reinforced cement concrete design mix M-25 using 20 mm graded stone aggregates in lintels over 1.5m clear span, beams and cantilevers complete all as specified and directed. Note:- Reinforcement to be measured & paid separately under respective item.

Use & waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed

Use & waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions with rough finished surface complete all as specified and as directed

Use & waste of form work to sides and soffit of floor or roof beams, beam haunching, girders, bressumers, lintels, cantilevers, shelves including supports, overhangs, etc rough finished complete all as specified and as directed

Use & waste of formwork to soffits of suspended slabs supported on wall and similar work not exceeding 200mm thick or lintel / beam (Horizontal or sloping) complete all as specified and directed

M & L for Anti-termite treatment by treating the bottom and sides of excavation at the rate of 5 liter of emulsion per square meter of surface area complete all as specified and directed

M & L for Anti-termite treatment by treating the backfill in contact with foundation at the rate of 7.5 liters of emulsion per square meter of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed

M & L for Anti-termite treatment by treating the top surface of filled earth at the rate of 5 liters of emulsion per square meter of surface complete all as specified and directed

M & L for Mild steel TMT bars 6 mm to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping as in stirrups for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for rendering 10 mm thick in CM 1:3 on ceiling of RCC or brick finished fair and even without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 100 mm thick plain cement concrete type C-2, 1:3:6 using 40 mm graded stone aggregate as in flooring complete all as specified and directed.

M & L for Hardcore of gauge 50 mm thick with broken stone n exc. 63 mm, deposited, spread and leveled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for non skid coloured ceramic floor tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.18 sqm but n exc 0.38 sqm, in floor ,wall etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the surface with 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for 25 mm thick plain cement concrete type B1 1:2:4, 20mm graded aggregate as in levelling course on floor and other similar works complete all as specified and directed.

M&L for Applying one coat of hot blown bitumen grade 85/25 as per IS-702-1988 @ 1.20 Kg/Sqm of each coat applied over primed roof surface including cleaning of surfaces

M&L for cement concrete tiles of size 30cm x 30cm x 20-22 mm thick factory made machine pressed conforming to IS-1237: 1980 laid over and including 15 mm thick screed bed in CM 1:6 mixed with polymer based liquid water proofing compound @ 200 ml mixed with 50 Kg of cement ( 1 Bag) and the joints of tiles shall be filled with polymer based cement proof joint filler (manufactured by approved company) on accessible roof area complete all as specified and directed.

S & F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators (sliding type) with extruded built up standard sections/appropriate Z section and other sections of approved make and conforming to IS:733 and IS:1285 , fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

M&L for preparation of new or previously untreated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old decorated surface of ceiling and applying three coat of white wash on ceiling complete all specified and as directed.

M&L for 35 mm thick flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

M&L for preparation of newly wood or wooden based materials surface of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M& L for Pressed steel frames 105 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified & directed.

S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections suitable for use with pad lock complete all as specified and directed.

S&F aluminium anodised barrel tower bolts of extruded section 150 mm long complete all as specified & directed.

S&F 150mm long aluminium alloy anodised handle complete all as specified and directed

S&F of floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel fixed in floor with over all length of cover plate 140 mm complete all as specified and directed.

Surface dressing n exc 15 cm deep in soft / loose soil and getting out exceeding 50 Mtr in soil complete all as specified and as directed.

M&L for 75 mm thick plain cement concrete 1:4:8 type D2 using 40mm graded crushed stone aggregate as in sub base of flooring complete all as specified and directed.

M&L for 60mm thick M-35 grade factory made vibratory compacted cement concrete rubber moulded, coloured interlocking paver block any shape and size conforming to IS 15658-2006 with grey cement and pigment as approved laid over sand cushion and joints filled with sand complete all as specified and directed. Note:- Sand shall be measured & paid under respective item.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed. Note:- Compacted thickness shall be measured for payment.

M&L for providing plain cement concrete kerb stone in side of interlocking tiles including slightly rounded or chamfered angle and throating and size as per direction of Engr-in-charge complete al as specified and directed

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick work, concrete surfaces with WPC @3% by weight of cement finished even and fair without using extra cement complete all as specified and directed.

M&L for reinforced cement concrete 1:1½: 3 type A-1 using 20mm graded aggregate as in slabs supported on walls, beams, and columns in floors, roofs landings, balconies ,canopies , deck slabs and in shelves and the like complete all as specified and directed

M&L for Granite 18-20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 20 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M & L for cement concrete 1:3:6 type C-2 , 40 mm graded aggregate in foundations, filling and mass concrete using 40 mm graded aggregate complete all as specified and directed

M&L for 40 mm thick plain cement concrete type B1 1:2:4, 20mm graded aggregate as in levelling course on floor and other similar works complete all as specified and directed.

M & L for non skid coloured ceramic floor tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but n exc 0.18 sqm, in floor ,wall etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the surface with 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured wall tiles in vertical surface 450X300X7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in 1:4 CM complete all as specified.

M&L for joint free vitrified non skid coloured tiles 10 mm thick area of each tile exceeding 0.18 and n.exc 0.36 Sqm in floor, wall, shelves etc, set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M & L Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed..

M & L Prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for mild steel hollow sections conforming to Fe-410 W (Gde E-250) quality A as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails & guides for sliding doors, fixed with angle cleats or other connecting plates complete all as specified and directed.

S&F 4 mm thick non asbestos fiber cement building board of 600x600 mm in size (HPSC E-classic) decorative finish fixed to aluminum /CGI frame work with hold down clips in false ceiling complete all as specified and directed.

M&L for collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top & bottom runners, brass handles, etc; erected in position and securing runners with hold fasts and brackets complete all as specified and directed.

S&F 12 mm thick toughened glass door with suitable locking arrangement with lock 6 lever and self closing devices with rebates including jointing cleats of suitable section for fixing builders hard ware fittings door spring with two Nos decorative type aluminium handle of 200 mm dia complete all as specified and directed.

S&F counter top wash basin plain white of size 415 x 415 x 145 mm including fixing of pillar tap, waste fitting & pipe 32 mm dia, bottle trap of 32 mm, union & fixed in position complete all as specified and directed.

S&F in repair 15 mm bore CP central hole basin mixer (swan neck/head type) with regular spout fancy type, cast copper alloy with capstan heads, long screwed shanks and fly nuts screwed down high pressure with or without lettered Hot or Cold and fly nuts, screwed for iron pipe fixed complete all as specified and directed. Make:- Cera cat Part No. 1015501 or equivalent make as specified in P.S.

S & F 600 mm long tubular towel rail, brass chromium plated of 20 mm dia complete all as specified and directed.

S&F shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed

S&F rotational moulded, multilayer (three layer) HDPE water storage tank white colour of 500 ltrs capacity(Cylindrical vertical with closed top) ISI marked fixed in position on existing places complete all as specified including 02 Nos 20mm dia full threaded GI tank nipple, 20 mm dia PTMT float valve epoxy coated Aluminium rod with high density plastic float ball( of minimum weight 210 gms ) and refixing of inlet, outlet & overflow pipe etc, complete all as specified and as directed.

S&F 75mm dia PVC (SWR) floor/Nahani trap with gratings including jointing to waste pipe, fixed in plain cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) complete all as specified and directed.

S&F vitreous china two piece EWC (pedestal Pattern) with cistern snow white / star white with 'S' type concealed trap, frontof back inlet including all fitting such as soft seat cover, lid, twin flush fitting, health faucet, CP brass angular cock with wall flange, CP brass toilet paper holder etc complete all as specified and directed. Make:- (i) Hindware model constellation premium for EWC & Cistern with Lid& accessories, Cera or equivalent make as specified in P.S.

S&F in repair vitreous china urinal, half stall type (flat back), of size 635x395x420mm, white, with grating and union for discharge pipe (excluding flushing cistern) including 32mm dia PTMT coupling, waste pipe and CP spreader with connected fittings complete, providing and fixing plugs, bedding urinal against wall in CM 1:2, complete all as specified and directed.

S & F angle cock cast copper alloy with butterfly or crutch handle, screwed down, high pressure with screwed both ends for iron pipes or for unions, 15 mm dia of pipe weight should not be less than 0.40 Kg complete all as specified and directed.

S&F chromium plated grating doom round 100 / 110 mm size with waste hole (minimum weight 40 grms) complete all as specified and directed.

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed

M&L for preparation of new plastered surface and applying two coat of acrylic exterior emulsion paint in required shade over a coat of primer over & including 1-2 mm thick water proof wall care putty on cleaned surface as per manufacturer,s specification etc. including all tools, plants scaffolding, safety belts complete all as specified and directed

Supply, laying and testing of Reinforced Concrete pipes, class NP3, 100 mm bore, laid and jointed with collars complete all as specified & directed.

Cutting holes into existing manhole brick wall manhole built in CM, connection new drains making good to pipes and rendering cutting out existing benching for and forming branch channel ( 1/2 round or 3/4 section) in cement concrete (1:2:4) type B1 smooth finished and reforming benching as required for internal dia of pipe 150mm complete all as specified and directed.

Taking down carefully submain wiring of any number of wire and size with earth wire on wooden batten / surface conduit/ casing caping complete with its all accessories complete all as specified and directed.

Taking down carefully aluminium batten point wiring of any type complete for light, fan socket or power point with fittings & fixtures such as ceiling rose, electric fittings, holders, switches, sockets, regulators, wooden batten, surface conduit/casing capping/concealed etc. removing materials including accessories for taking credit and making good disturbed surface to match the existing surface & taking down old light fitting and fixtures complete all as specified & directed. Note:- Contractors quoted their rate of this item deemed inclusive of unscrewing of the serviceable fitting and fixtures shall be contractor's property as per Sch of credit. (ii) Quoted rate also deemed to include cost of cutting chases for taking out concealed conduit and nitch for terminal boxes etc.

M&L for point wiring using FRLS PVC insulated unsheathed /multi stranded copper conductor cable 1.5 sqmm including 1.5 Sqmm FR PVC insulated unsheathed copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bend, junction box and modular metal flush sunken box 60 mm deep & 1.6 mm thick duly painted inside and anticorrosive out side for mounting switches, sockets, fan regulators etc with modular white cover plate with frame of suitable size, connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar (1:4) and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc (conduit shall be fixed on surface of ceiling with necessary saddles where concealing of conduit is not feasible), for light/fan/Exhaust fan/ bell point etc complete all as specified and directed. Note : (a) Switch/bell push/fan regulator etc will be measured and paid separately (b) The unit rate quoted is deemed to be inclusive of cost of cutting chases in wall for providing concealed conduit and making good to match with existing finish/surfaces. (c) Colour code of wire shall be strictly followed , Red for Phase , Black for neutral and green for earth wire

One light/fan/bell point controlled by one switch

One point for socket outlet 5 amp same board.

One point for socket outlet 5 amps on independent board

All as per srl item No. 138 above but for one 3 pin socket outlet 15 amps, independent, with cables 4.0 sqmm size on independent board 4.0 Sqmm earth wire complete all as specified and directed.

S&F ceiling rose surface type bakelite 65x50mm three terminal complete all as specified and directed.

S & F lamp holder, PVC/Polycarbonate type with back plate suitable for batten fitting complete all as specified and directed.

S&F modular Switch piano flush type single pole one way 6 amps complete all as specified & directed.

S&F modular socket outlet 2 in 1, 3 pin, 2 module 6 Amps flush type universal complete all as specified & directed.

S&F modular Switch piano flush type single pole one way 16 amps complete all as specified & directed.

S&F modular Socket out let 2 in one, 5/3 pin 5 & 16 Amp 2 module complete all as specified & directed

S&F fan regulator, modular type, 5 stepped, 120 W, single phase 230 volt including connection complete all as specified & directed.

M&L for concealed submain wiring using FRLSH PVC insulated, unsheathed stranded copper conductor cable two single core of size 6 Sqmm of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories along with one run of PVC insulated unsheathed stranded copper conductor of size 6.0 Sqmm as earth continuity conductor complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

M&L for concealed submain wiring using FRLSH PVC insulated, unsheathed stranded copper conductor cable two single core of size 4 Sqmm of voltage rating upto and including 1100 volts drawn in and including PVC concealed conduit of dia not less than 20 mm dia with all fittings and accessories along with one run of PVC insulated unsheathed stranded copper conductor of size 4.0 Sqmm as earth continuity conductor complete all as specified & directed. Note:- (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one length. (ii) The cost for cutting, chases required shall deemed to be included in the quoted unit rate.

S&F sheet metal enclosure for MCB's 240 volt 6 way single pole and neutral with 200 amps rated busbar double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

S&F sheet metal enclosure for MCB's 240 volt 4 way single pole and neutral with 200 amps rated busbar double door on wall with and including suitable flat iron clamps duly grouted/ fixed flush in the wall complete all as specified and directed.

S&F MCB single pole & Neutral, 40 to 63 amps rating, 240 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S&F MCB single pole, 5 to 32 amps rating, 240 volts, 'C' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S & F in replacement for LED light fitting ultra slim linear LED lighting fixture with co- extruded polycarbonate body environmental friendly, energy efficient tube light complete with all accessories internally pre- wired and including LED lamp 20 watt 01 No and connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

S&F in replacement LED mirror light fitting 2 feet, 10 watt with high output with opal diffuser 230 V AC decorative type with driver holder and LED lamp including connecting with three core flexible copper conductor cable of suitable size & suitable for mounting clamps PVC square box 75x75mm - 2 nos etc complete all as specified and directed.

Taking down ceiling fan & cable end, dismantling blades and removing fan and blades, oiling, greasing and painting of ceiling fans complete apply one coat of synthetic enamel paint by spraying including filling cavities with filler after cleaning of all dust etc. and re-hanging to the same hook and connecting up including provision of cable from ceiling rose to fan complete all as specified and directed. Note - (i) Fans to be collected by the contractor at their own arrangement from AGE E/M store for painting . (ii) Cost of spare parts as required i.e. nuts, split pin, plate washer to make the properly hanging of fan are deemed to be included in the quoted rate.

S & F VTPN DB 4 way DPX³ 100A MCCB Double door DB's as per IEC 61439-3, suitable for flush mounting and surface mounting with 250 Amp copper busbar for each phase with 2 Neutral bar, 2 earth bar and cable ties for cable management, fully insulated busbar & shrouded neutral bars, improved pan assembly for ease of installation, prefitted masking sheet, reversible door for IP 43 & IP 54 DB's with provision for DPX³ 100 MCCB as incomer and SP/TP MCB's as outgoing with metal door complete all as specified and directed.

S&F MCB single pole, 40 amps rating, 240 volts, 'B' series, 10 KA breaking capacity & making connection complete all as specified and directed.

S & F in repair MCCB 100 Amps, 415 Volts, 4 Pole, breaking capacity 16 KA, ISI marked, adjustable type complete all as specified & directed.

M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type B-0 using 20mm graded stone aggregate cover re-inforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete all as specified and directed. Note:- PCC pit shall be provided at least 500 mm away the earth pit and not just on the earth pit and extra cost of additional length of water pipes & fittings junction etc shall be deemed to be included in the quoted rate. (ii) Item includes the cost of 7.5 mtr earth lead wire and G.I. pipe for protection of earth wire are also included in the quoted rate.

Supply and fixing in replacement LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection bracket for street light made out of 40 mm bore GI pipe medium grade not less than 1.2 mtr length bent at 120 degree to shape fixed on pole/wall with and including 50x6mm FI clamps = 02 Nos with nut bolts, washers including painting of clamps with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F Exhaust fan, steel body AC single Phase. 230V of size 300 mm single phase 230 V AC , 1200 RPM Range complete with louvers shutter including making hole & grouting in wall , mounting frame with nut, bolts, washers, fasteners , etc and connecting exhaust fan to ceiling rose including provision of three core flexible copper cable of size 1.5 sqmm not less than 0.5 mtr long for connection & testing including writing MES No complete all as specified & directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm 4 core complete all as specified & directed. Note:- Earth work, Sand & Bricks shall be paid separately under respective items

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m depth as in soft/ loose soil including forming of bottom surface to required level or slope for foundation, shaft, well, cesspit, manholes, laying of CI/ GI pipe / cable getting out complete all as specified and directed.

Supply & laying sand coarse dry as in cushioning of underground electric cable in trenches, laid to a uniform thickness of 23 cm (15 cm under the cable & 8 cm over the cable) complete all as specified and directed. Note: Only punned depth shall be measured & paid.

Supply and laying sub class 'B' bricks laid dry and flat across the length of cable for protection of cable complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 Sqmm 2 core complete all as specified & directed. Note:- Earth work, Sand & Bricks shall be paid separately under respective items

S & F DB with single phase & neutral MCB Distribution Box of 8 Way,220 volts, double door of protection grade IP 43 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type with 200 Amp rated copper bus bar, Din rail, earth bar suitable for mounting MCBs conforming to IS 13032 & 8623 complete all as specified and directed. Note:- MCB shall be paid separately under respective item.

All as per srl item No. 138 above but for one bell/ buzzer point controlled by one push button on the same board with other switches or independent

S&F call bell, ding dong type, AC, 230 V, single pole complete all as specified & directed.

S&F Modular metal flush box of 6 module complete all as specified & directed

S&F Modular metal flush box of 4 module complete all as specified & directed

S&F Modular metal flush box of 3 module complete all as specified & directed

S&F Modular white cover plate with frame of 6 module complete all as specified & directed

S&F Modular white cover plate with frame of 4 module complete all as specified & directed.

S&F Modular white cover plate with frame of 3 module complete all as specified & directed

S&F bell push modular flush type 6 amp, 1 module SP, 230 volt AC complete all as specified & directed.

Supply & fixing ceiling fans complete with blades ,down rods , electronic regulator and accessories ,230V ,1200mm sweep .min air delivery 210 CFM with service valve 6.00 BEE .five star rated with brushless direct current ( BLDC) including required length and size of copper stranded conductor for connection from ceiling rose to connector of fan including testing on completion complete all as specified and directed.

S&F LED tube light fittings decorative ultra slim linear fixture with extrudedalluminium heat sink environmental friendly Energy efficient ready to use pack ,1x18/20 Watt ,4 feet, surface mounting type extruded pvc, snap on installers and domestic electronic Driver ,connector block ect.with all assoceries internal prewired & including connecting up with 2 core flexible copper conductor cable with suitable size & suitable for and mounting clamps PVC square box 75x75mm - 2 Nos etc complete all as specified & directed.

S&F in replacement energy efficient LED light of 10 Watt of length - 02 Feet long having minimum 1150 Lumen output, wide voltage protection range 140-270 Volt AC housed in extruded aluminum housing (enhances safety) with high quality polycarbonate diffuser including making connection with two core PVC insulated, sheathed copper conductor cable of size 23/0.0076 complete all as specified and directed.

S&F in replacement LED light fitting 10 Watt bulkhead luminaries in high pressure die cast aluminium housing, lumen out put - 700 Lm, colour Temp - 6500 K having Ingress protection - IP 65 for dust, water & IK 08 for external impact including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F in repair PVC insulated, unsheathed flexible twin twisted copper conductor wire of nominal size 23/.0076, 1100 Volt grade, ISI marked complete all as specified and directed.

Schedule of Credit (MINUS) Rs. 30035.00 B/F from Serial Page No. [Note : Details of items for schedule of credit is given on Srl Page No. ] This amount shall be automatically deducted to arrive at tendered sum

JMD Enterprises (BID ID -3119150)

Airways Enterprises (BID ID -3105679)