PROVN OF WATER ELECTRICITY AND DRAINAGE CONNECTION TO INLIVING ACCN OF WOMEN AGNIVEER STEEL GRATING ON TOP OF STORM DRAIN AROUND INCS AREA AND TILLANGCHANG PARK SPCL RPR TO SEWAGE LINE GULLY TRAP MANHOLE STORAGE WELL OF SAILOR INLIVING ACCN DEFECTIVE

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft or loose soil etc complete all as specified nd directed.

Excavating in trenches, n exc 1.5 m wide and exc 1.5 m in depth beyond the first 1.5 m depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft or loose soil etc complete all as specified nd directed.

M&L for PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in concrete bed of Internal dia of pipe 200mm including packing under and haunching against the sides of pips after they are laid and tested complete all as specified and directed for the following

M&L for RCC pipes 200mm dia grade 'A' laid in trenches and jointed complete all as specified and directed.

Returning and filling in including spreading, levelling, watering and well rammed in layers not exec 25 complete all as specified and as directed as in hard/dense soil complete all as specified and as directed

M&L for providing precast cement concrete block masonary with solid blocks exc 10 cm width, type C-1 (1:3:6) using 20mm graded aggregate and set in cement mortar (1:6) all as specified and directed.

M&L for rendering 15mm thick plastering in cement mortar 1:4 on fair faces of brick work or concrete surfaces mixed with integral water proofing compound as per manufacturers instructions, finished even and smooth without using extra cement complete all as specified and directed. Note : Integral water proofing powder will be measured and paid separately under relvant item of Schedule 'A'

S&F for cast iron/mild steel Sections of Grade Fe 410-W, (Gde- E-250) quqlity-A, as in chamber,drain etc fixed with connecting plates including bending, welding etc complete

M&L for preparation of new steel surfaces exc 10cm width of girth and applying two coats of synthetic enamel paint over a coat of red oxide primer.

M&L for removing excavated materials as in soil exc. 1.50 km but n exc. 5 km and depositing where directed out side of MoD land etc complete all as specified

Supply only Integral Water proofing compound complete all as specified and directed.

S & F for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed alusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 all as specified and directed.

M & L for cement concrete type B0 1 : 2:4 (12.5 mm graded aggregate) as in kerbs/paddings or mud stops or bedding for tiles etc chamfered at edges complete all as specified and directed.

M & L for removal of blockage and cleaning of sewage lines of 100 mm bore by rodding from manholes to manholes or manholes to cleaning eyes, taking out all debris, sludges and solid materials from sewage lines and removing outside MD land and well flushing with water complete all as specified and directed by Engr-in-Charge.

Description all as per item No.14.00 herein before but 150 mm bore.

M & L for removal of blockage/ waste and cleaning gully traps and Nahani traps of any description and size for smooth flow all as directed.

M & L for removal of blockage and cleaning of manholes of size 800 mm x 800 mm and upto a depth of 1 m by removing sludge/ liquid foul/ waste etc complete and ensuring smooth flow of sewage including sprinkling of bleaching powder after cleaning of manholes and disposing the waste outside defence land all as directed by Engr-in Charge.

Description all as per item No. 17.00 herein before but manhole of size 900 mm x 1200 mm and depth of manhole exc. 1 m and not exc 2 m.

Description all as per item No. 17.00 herein before but manhole of size 1400 mm dia and depth of manhole exc. 2 m and not exc 3 m.

M&L plain cement concrete 1:3:6 type C2 using 40mm graded stone aggregate as in foundation & filling in Mass concrete complete all as specified and directed.

Removing of excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5 m above starting point complete all as specified and directed.

Demolition and breaking up drain pipes 100 mm dia (Salt Glazed ware, AC or reinforced concrete) set in cement mortar including PCC bed and haunching and removal of debris outside the MD land complete all as specified and directed.

Description all as per item No. 22.00 above but 150 mm dia.

M&L for Salt Glazed Stoneware pipes grade 'A', 100 mm bore, laid in trenches and jointed all as specified and directed.

Description all as per item No. 24.00 herein before but 150 mm bore.

M&L for PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) for bed to drain pipe 100 mm bore including packing under and haunching against the sides of pipes after they are laid and tested all as specified and directed.

Description all as per item No. 26.00 herein before but bed to150 mm bore.

Demolition/breaking up or down CI pipe of any size, fixed in any position complete all as specified.

S&F cast iron soil, waste and vent spun pipes 100 mm dia, in any length with or without ears, with cement joints, laid in trenches or in floors and including taking down existing complete all as specified and directed.

S & F cast iron soil, waste and vent spun pipes 75 mm dia, in any length with or without ears, with cement joints, laid in trenches or in floors and including taking down existing complete all as specified and directed.

S & F cast iron bends 100 mm dia (any radius) diminishing pieces or tapers (larger bore measured) all as specified and directed.

S & F cast iron bends 75 mm dia (any radius) diminishing pieces or tapers (larger bore measured) all as specified and directed.

Demolition of precast concrete block walling built in cement mortar all as specified and directed.

M&L for providing precast cement concrete block masonary with solid blocks exc 10 cm width, type C-1 (1:3:6) using 20mm graded aggregate and set in cement mortar (1:4) all as specified and directed.

All as per item No 34.00 above but except blocks.

M&L for preparing the new plastered surfaces and applying three coats of white lime washing on walls complete all as specified and direcrted.

S&F in repairs Cast iron work grade FG 150, articles exc 5 kg each each unmachined, in brackets, gully traps,gratings, railing, frames,manhole covers, fire and soot doors, dampers, stopvalve boxes, gate stops,parts of ranges, balusters and similar articles complete all as specified and directed.

Dismantling cast iron work of any description

M&L for Excavation over areas n exc 1.5m deep hard and dense soil and getting out complete all as specified and directed.

Ditto as per item no 31 but exc 1.5m but not exc 3.0 mtr depth complete all as specified and directed.

Ditto as per item No-31 but exc 3m deep but not exc 4.50 mtr depth hard and dense soil complete all as specified and directed.

M&L for PCC 1:4:8 type D2 for Column lean concrete complete all as specified and directed.

M&L for RCC as in footings for coloumn M-25 complete all as specified and directed.

M&L for RCC as in coloumn M-25 complete all as specified and directed.

M&L for RCC M25 as in band complete all as specified and directed.

M&L for RCC M25 as in slab/ Cover complete all as specified and directed.

M&L for Brick Bat filling Aggregate for loose filling, of gauge 80 mm to 150 mm graded complete all as specified and directed.

M&L for Brick work sewer bricks curved on plan n exc 6m radious for soakwell etc in CM 1:3 complete all as specified and directed.

M&L for Honey comb brick work with sub class brick walling in CM 1:3 complete all as specified and directed.

M&L for Reinforcement TMT bars 8 mm dia TMT bars complete all as specified and directed.

M&L for TMT bars 12 mm dia and 10 mm Dia complete all as specified and directed.

S&F 80mm dia vent pipe Asbestos cement pipes in any length with cement joints; fixed to walls complete all as specified and directed.

M&L for AC vent cowl 80 mm complete all as specified and directed.

M&L for Rendering 15 mm thick in CM 1:4 externaly above GL complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed

M & L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, o r forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 including portions framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc complete all as specified and directd.

S & F for 1.00 mm thk Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required etc complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces of wall/ceiling and likes including racking out joints, hacking for keys scrubbing down with water etc any description including removal of rubbish outside MoD land, complete all as specified and directed. Note : The rate quoted by the Contractor is deemed to be included necessary scafolding and form works.

M&L for preparation of new plastered / decorated wall surfaces applying two coats of Acrylic Emulsion exterior grade, weather proof antifungal Paint over a coat of primer including necessary scafolding and safety measures as required etc complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of new plastered / decorated wall surfaces, applying Two coat of oil bound distemper over a coat of alkaline resistant primer over a coat of 3mm thk wall care putty including necessary scafolding and safety measures as required etc complete all as specified and as directed by Engr-in-Charge.

Taking down rolling shutters of following sizes, replacing worn out/unserviceable parts with new ones, overhauling, applying grease, refixing in position and making functional complete all as directed :- Note : Replacement of parts will be measured and paid for seperately in respective items

(a) Area not exceeding 8 Sqm each

(b) Area exceeding 8 Sqm but not exceeding 12 Sqm each

(c ) Area exceeding 12 Sqm but not exceeding 20 Sqm each

(d) Area exceeding 20 Sqm but not exceeding 26 Sqm each

S&F Steel rolling shutters of 1.25mm thk laths, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated complete gear operated type with bevel gear box and crank handle all as specified and directed. Note:- Suspension shaft and connecting rod will be measured and paid for separately.

S&F in repairs Mild steel guide channel of size 75mm depth, 25mm width and 3.15mm thick including fixing of cleats or supports (not exceeding 750mm c/c) for attachment to the wall or column by means of bolts or screws all as specified and directed.

S&F in repairs Suspension shaft made out of mild steel pipe confirming to IS-1161-1968, medium class 50mm dia all as specified and directed.

S&F in repairs “0 0” gauge helical wire or flat spiral spring fixed with suspension shaft all as specified an directed.

S&F in repairs “0” gauge helical wire or flat spiral spring fixed with suspension shaft all as specified an directed.

S&F in repair cast iron ball bearing for rolling shutter complete all as specified and directed

S&F in repairs safety lever locks mild steel with 4 levers for rolling shutters all as specified and directed.

Supply & Laying including jointing, testing and commissioning of two run of 3.5 core 25 Sqmm XLPE insulated, armoured, heavy duty, LT UG electric cable with aluminum conductor 1100 volt grade including provision of lugs, glands etc laid in trenches or fixed on wall/pole or drawn through GI pipe complete all as specified and directed by Engineer-in-charge. Note - (i) Excavation & earth work, sand cushioning and PCC cover for cable protection will be measured & paid for seperately (ii) Both run of cable will be measured seperately in RM.

Supply and spread dry river sand in trenches for cable cushioning all as specified in clause 19.75 of SSR Part-I. Note:- Punned thickness of sand only will be measured & paid

Supply and lay un-reinforced pre-cast concrete cable cover, class LV, type 1, flat, size 250mm x 150mm x 40mm in replacement of existing burnt bricks complete all as directed.

M & L for MCCB 4 pole, 415 V of 100 Amps current rating with breaking capacity 16 KA complete with connection testing and commissioning complete all as specified and directed.

Material and labour for earthing complete with galvanised steel earth plate electrod 60cmx60cmx6mm thick,burried directly in ground(earth pit not less than 2.25 metres deep below round level) with top edgeof the plate not less than 1.5 metres below normal ground level,connected to galvanised iron strip 32x6 mm as earth lead by means of bolts,nuts,check nuts and washers of galvanized iron or steel all as shown in plate no 3 to the earthing test point all as specified and indicated including testing on compltetion. (Rates inclusive of neccessary excavation in any type of soil, earth work, PCC pit, CI cover, funnel with watering pipe, suitable size of light grade GI Protection pipe for earth strip in ground etc. all as required at site for complete earthing).

Material and labour for Cutting CI /DI Pipe line of size up to 200 mm to provide new connection by inserting CI TEE of Size 100 mm including necessary lead joints,Excavation,returning,filling in of excavated material complete all as specified. Note: CI Special and fittings will be paid and measured separately.

S & F fittings for cast iron pipe up to 150 mm dia of flanged / socketed type such as bend any type and radius, tee straight / tapper, tail pieces, collars etc; conforming to IS 9523-2000 complete including all jointing materials such as nuts, bolts, washers, rubber gaskets etc, all as specified.

Supply and lay pipe galvanized, “Medium class”, including fittings 40 mm dia.

Supply and lay pipe galvanized, “Medium class”, including fittings 25 mm dia.

Labour for carrying out horizontal boring below roads/PCC hard standing/Drain by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure complete all as specified as directed for inserting GI pipe of the 25 mm dia sze with a depth upto 1.5m & length of road upto 12m of the follwing size of bore.

Supply and fixed gate valve size 40mm dia complete all as specified and directed by engr in charge.

Supply and fixed gate valve size 25 mm dia complete all as specified and directed by engr in charge.

M&L for construction of Valve pit chamber 90 cmx90cm (inner dimension) and 90 cm deep , from the top of MS cover fixed on PCC Base , top cover shall be of 3 mm thick MS Sheet with locking arrangement of pad lock of 50mm size including brick work with sub class"B" bricks in CM 1:4 including 15 mm thick plaster in CM 1:4 (internally and externally) and necessray earth work in anu type of soil including returning filling in and disposal of surplus oil to a distance n exc 50 mtrs and 150 mm thick PCC 1:4:8 , type D-2 , using 40mm graded stone aggregates as in floor complete all as specified and directed.

Dismantling and taking down unsv horizontal mounted single or 3 phase rolling door motor, CI body make of strong life from rolling shutters having at height appx. 9 mtrs including connceted accessories for repair/replacement of unserviceable spare parts including transportation to the workshop and re-installing the same after repair work & testing all as specified and as directed.

Dismantling and taking down unsv Gear box of any type from rolling shutters having at height appx. 9 mtrs including connceted accessories for repair/replacement of unserviceable spare parts including transportation to the workshop and re-installing the same after repair work & testing all as specified and as directed.

M&L for Opening existing rolling door motor having capacity of 1 phase, 230 volt, 550 Watt, max raising hight 9 mtr, advancing force 800 (kgf), make of strong life or any other make, cutting/removing the existing burnt winding and rewinding by using super enamelled copper winding wire of existing wire gauge incl other allied items such as varnish tape, sleeve, greasing, bearing, bushes etc of suitable size, including necessary repairing of rotor shafts if required with refixing, testing and commissioning complete all as specified and directed. Note:- Rates deemed to be included for decoupled and coupling with gearbox, the cost of transportation charges for carrying the motor from site to workshop and back, Nothing extra shall be admissible.

M&L for Opening existing rolling door motor having capacity of 3 Phase, 440 volt, 550- 900 Watts, max raising hight 9 mtr, manually operated chain system, 1500 Kgf-2000 Kgf lifting force make of strong life or any other make, cutting/removing the existing burnt winding and rewinding by using super enamelled copper winding wire of existing wire gauge incl other allied items such as varnish tape, sleeve, greasing, bearing, bushes etc of suitable size, including necessary repairing of rotor shafts if required with testing and commissioning complete all as specified and directed. Note:- Rates deemed to be included for decoupled and coupling with gearbox, the cost of transportation charges for carrying the motor from site to workshop and back, Nothing extra shall be admissible.

M&L for complete overhauling of Gear box suitable for rolling doors having raising height upto 9 mtrs as per existing make for general inspection of shaft, bearings, gear govrner, and re-installation after replacing anti chain, chain wheel, bearings, seals and with SS nut bolts, metalising the shafts if required and re threading bottom plate by lathe work including body repairs, welding works and complete testing all as specified and as directed.

Supply, installation, testing and commissioning of single phase, 220 Volts, rated power upto 550 watt, advance force (in Kgf) of 800 suitable for rolling door having maximum raising height of 9 mtrs, dia of roller 154 mm including gear box, control panel, clutch, brake releasing string, limit switch, sprocket, lock key box with 3 button switch, motor mounted bracket including connected items, nut bolts and manually operated hand chain including making necessary power connection cable complete all as speified and as directed. Make :- Strong life rolling motor or make as approved by GE.

Supply, installation, testing and commissioning of 3 phase, 440 Volts, rated power 550- 900 watt, advance force (in Kgf) of 1000 - 2000 as per site requirement suitable for rolling door having maximum raising height of 9 mtrs, dia of roller 154- 209 mm as per site requirement including gear box, control panel, clutch, brake releasing string, limit switch, sprocket, lock key box with 3 button switch, motor mounted bracket including connected items, nut boltsand manually operated hand chain including making necessary power connection cable complete all as speified and as directed. Make :- Strong life rolling motor or make as approved by GE.

Supply and fixing in repair clutch drive including hand drive chain with connecetd accessories complete all as specified and as directed

Supply and fixing in replacement Lock Key Box with UP DOWN STOP 3 Button Black Plastic Housing Push Button Switch Control size of 100mm x 40mm x 20mm using premium stainless steel material with rustproof painting on the bottom fix on wall surface including making necessary connection suitable for rolling Shutter door motor having lifting force up to 2000Kgf complete all as specified and as directed.

M&L for opening control panel enclosed with rolling motor, checking, detect any type fault rectify and replace parts like relay, control wiring, contactor, capacitor if required including making necessary connection complete all as specified and as directed.

Taking down old submain wiring cable of any size/ type alongwith earth wire with or without concealed/ surface conduit/ casing capping complete all as specified and directed.

M&L in replacement, sub main wiring with proper colour coding, FRLS PVC insulated copper conductor, unsheated, multi-stranded, copper conductor, cable of two runs of 10 Sqmm for phase and neutral and one run of 10 Sqmm for earth wire, drawn through existing conduit fixed in wall/ ceiling etc and connected complete all as specified and directed by Engr-in-Charge. Note: Phase should be of Red/ Yellow/ Blue, neutral should be of black and earthing wire should be of green colour. Two runs of cable for phase/ neutral and one run of cable for earth will be measured and pais as one unit length

All discription as per items no 93.00 above here-in but cable of four runs of 10 Sq mm for phase and neutral and one run of 10 Sqmm for earth wire

S & F in repair MCB DB SPN, 4 way, 240 Volt, double door powder coated sheet steel enclosure for surface mounting fitted with 200 Amps bus bar and din channel complete all as specified and directed.

S & F in repair, 6-32 A, 240V, 10KA, C Curve , MCB Single poles with electrical connection with suitable size of thimble, testing and commissioning complete all as specified and as directed.

S & F in repair, 32 Amps, 240V, 10KA, C Curve , MCB SPN with electrical connection with suitable size of thimble, testing and commissioning complete all as specified and directed.

S & F in repair, Single pole and neutral enclosure with a two pin and earth plug and socket complete with one 20 amp capacity double pole MCB connection testing and commissioning complete all as specified and directed.

S & F in repair, Triple pole and neutral enclosure with a two pin and earth plug and socket complete with one 40 amp capacity triple pole MCB connection testing and commissioning complete all as specified and directed.

S & F in replacement, copper conductor pvc insulated sheathed cable 3 core 2.5 sqmm FR grade, fixed on wall/ ceiling with suitable size of saddles screws etc including taking down existing cable all as specified and directed.

S & F in replacement, Limit switch suitable for motor of rolling shutter door having maximum raising height of 9 mtrs including making necessary connection complete all as specified and as directed.

M/S SUMEET MADHAV ASNOTIKAR (BID ID -3337239)