REPAIRS TO ROOF SHEET, FLOORING, FALSE CEILING, WALL PANELS, JOINERY, ALUMINIUM PORTION AND CERTAIN REPAIR WORK AT SHILLONG CANTT AREA UNDER GE SHILLONG

Amount

Dismantling of plain or corrugated steel sheeting any guage thickness including nainital or similar pattern roof covering complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semicorrugated etc) sheets in roof covering complete all as specified and directed.

Dismantling of timber scantling 40 sqcm over in section in any position (unframed work) complete all as specified and directed.

Dismantling of timber in fillets, rails, posts, rafters, purlins etc under 40 sqcm in section unframed work complete all as specified and directed.

Dismantling wrought Iron or mild steel work of any description not other wise described complete all as specified and directed.

Dismantling boarding any description fixed in any position with nails complete all as specified and directed.

Dismantling of wall/ceiling boards (fibre, pulp,insulation, etc.) or insulation boards/ slab/blankets, any thickness including cover fillets complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness in floors laid bedded and pointed in any mortar etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm thickness (below/ above ground level) complete all as specified and directed.

Demolition of precast concrete block walling built in cement mortar complete all as specified and directed.

Demolition of reinforced cement concrete of any description in any position not otherwise described complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area exc 1.5 sqm but n.exc 4 sqm eachcomplete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area n.exc 1.5 sqm each complete all as specified and directed.

Taking down shutters of any description exc 1.0 sqm but n. exc 2.0 sqm eachcomplete all as specified and directed.

Taking down shutters of any description not exc 1 Sqm each complete all as specified and directed.

Taking down shutters of any description nexc 1.0 Sqm refixing in same opening complete all as specified and directed.

Taking down shutters of any description exc 1.0 Sqm and nexc 2 sqm refixing in same opening complete all as specified and directed.

S&F CGI 0.63 mm thick mild steel sheeting with two corrugations side lap,fixed with coach screws and washers in roofs walls etc with grade of zinc coating 120 gms fixed with l-type or J-type bolts complete all as specified and directed.

S&F PGI 0.63 mm thick mild steel sheeting in ridges hips valley gutters drip and straight flashings(length and girth as fixed) with grade of zinc coating 120gms complete all as specified and directed.

S&F pre-painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick as in roof covering of tensile strength 550 mpa including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour complete all as specified and directed

S&F pre-painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick as in roof covering of tensile strength 550 mpa including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour complete all as specified and directed

M&L 2nd class hard wood in scantling clean sawn timber fixed complete all as specified and directed.

M&L Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with Two coats of Creosote complete all as specified and directed.

M&L plain fillets square rectangular or triangular in section clean sawn secured with nails or brads (2nd class hard wood) sectional area exc 13 sqm n exc 25 sqcm complete all as specified and directed.

S&F 40mm thick 2nd class hard wood boarding in floors and skirting plained one side with butt joints and fixed with nails complete all as specified and directed.

S&F 20mm thick 2nd class hard wood boarding in eaves board/fascia plained one side with butt joints fixed with nails complete all as specified and directed.

M&L 6mm thick plywood, grade BWR type BB fixed to timber frame work with nails complete all as specified and directed.

M&L 6mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face on one side fixed with screws to timber frame work on wall complete all as specified and directed.

M&L for preparation of old treated wooden surface of any description over 10 cm in width or girth with one coat of french polish incl cleaning and preparing the surface incl a coat of wood filler on new works with two or more coats complete all as specified and directed.

M&L for 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice laminations and other side balancing white lamination as in kitchen cabinet/cup-board complete all as specified and directed.

S&F Continuous (Piano) hinges, brass, width of flaps 30 mm (when open) complete all as specified and directed.

S&F Magnet catches for cupboard shutter, brass body and striking plate including letting in complete all as specified and directed.

S&F Extruded brass handles, 100 mm size, fabricated type, polished complete all as specified and directed.

S&F Anodised Aluminium frame work for snapgrid false ceiling comprising of Gl perimeter channnel 0.55 mm thick with Main T- flange of 25 mm and web of 30 mm fixed to surrounding wall angle with flange and web 25 mm each , Cross T with flange 25 mm and web 25 mm fixed to main T, Main T is suspended from soffit @ 1200 mmm c/c using GI wire of 4mm thickness GI frame will be 60 x 60 cm to recieve E-board ceiling complete all as specified and directed.

M&L 4mm thick E Board 600x600 mm prepainted fibre boards ceiling designer/decorative type with different designs as approved by the Engr-in-charge fixed or laid in ceiling timber /GI/ aluminium frame work in ceiling flat or sloping, all as per manufacturer instruction complete all as specified and directed.

M&L non asbestos fibre cement building boards of 4mm thick fixed or laid/ inserted to timber frame work fixed in jointless finish with jointing compound and jointing tape as per manufacturer instructions complete all as specified and directed.

M&L for applying two coats of White wash on ceiling including preparation of new or undecorated surface complete all as specified and directed.

M&L fillets plain or bullnosed , splayed , chamfered , or rounded on one face or edge in section wrought secured with nails or brads (2nd class hard wood) sectional area exc 3 n exc 6 sqcm complete all as specified and directed.

M&L for preparation of new or previously untreated wooden surface of any description n.exc 10 cm width or girth applying two coats of Synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for light shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

M&L for light shade vitrified ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick rendering in CM 1:3 complete all as specified and as directed

M&L for Non skid light shade joint free ceramic tiles, 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour over 15mm thick screed bed in CM 1:4 complete all as specified and directed

M&L for Non skid light shade, joint free ceramic tiles, 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour over 10mm thick rendering in CM 1:3 complete all as specified and directed.

M&L for Non skid light shade, joint free ceramic tiles, 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour over 15mm thick screed bed in CM 1:4 complete all as specified and directed

M&L for Non skid light shade, joint free ceramic tiles, 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour over 15mm thick screed bed in CM 1:4 complete all as specified and directed

M&L for Glazed ceramic light shade tiles in vertical surface of size 450 x 300 x 7mm/300x600x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with the tile colour over 10mm thick backing coat in CM 1:3 complete as specified and directed

M&L for machine pressed pre polished chequered cement concrete tiles 300x300x25mm thick over 15mm thick screed bed in CM 1:4 set & jointed in neat cement slurry & pointed in white or coloured cement to match as in floor complete all as specified and directed.

M&L Granite (of any tipe) tiles 18-20 mm thick machine cut , bedded and jointed with grey cement and pointed with white cement with admixtures over 20mm thick rendering in CM 1:4 complete all as specified and directed.

M&L machine pressed pre-cast concrete rubber moulded coloured interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment complete all as specified and directed.

M&L Sand filling under floor including well ramming for laying of interlocking paver blocks complete all as specified and directed.

M&L PCC, (1:2:4) Type B-1, 40mm thick as in floor finished even and smooth without using extra cement complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in path, plinth protection, sub-floors etc finished even and fair or even and rough as reqd complete all as specified and directed

M&L for PCC (1:3:6) type C-2 using 40 mm graded stone aggregate as in surface channel and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

M&L Precast cement concrete block masonry with solid block exc 10 Cm in width with PCC, type C1 (1:3:6) using 20mm graded stone aggregate) and setting in CM 1:6 complete all as specified and directed.

M&L Precast cement concrete block masonry with solid block 10 Cm thick with PCC, type C1 (1:3:6, using 20mm graded stone aggregate) (with plain or interlocking joints and setting in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L Precast RCC cover slab etc type B1 (1:2:4) using 20mm graded stone aggregate) set in CM (1:6) complete all as specified and directed.

M&L TMT bars 10 mm dia & over, cut to length, bend to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with & including mild steel wire not less than 0.90 mm dia on securing with clips complete all as specified and directed by Engr-in-Charge.

M&L for Rendering 15mm thick on fair faces of concrete surface of wall in CM (1:4) finished even and smooth without using extra cement all as specified and directed.

Supply only integral WPC (ISI Mark) complete all as specified and directed.

M&L for for applying two or more coats (over 1 mm thick plaster of paris wall care putty) of 100% premium acrylic emulsion paint having VOC less than 50 gm/ltr and UV resistance as per IS 15489:2004, Alkali & fungal resitance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over old surface on external surfaces including preparation of new surface complete all as specified and directed.

S&F 2nd class hard wood plain, solid, straight chawkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F 30mm thick flush shutter solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 30 mm thick 2nd class hard wood plain framed panneled shutter any number of panels with panels of timber of veneered particle board with commercial face veneers flat on both side with feather edged complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted without and mitred beads for securing glass or gauge etc all as specified in SSR Pt 1sec-8.24(a) complete all as specified and directed.

S&F 30mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted without and mitred beads for securing glass or gauge etc all as specified in SSR Pt 1sec-8.24(a) complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood and wood based materials of any description not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M/L 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pan complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S/F Factory mabe solid panel PVC door shutter 30 mm thick (style) considering of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails, lock rail & bottom rails on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed togeather with solvent cement, fixing in the frame at site complete all as specified and directed.

Solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforcement with M.S square tube, supplying & fixing in openings, complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, size of hinges 100mm complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, size of hinges 75mm complete all as specified and directed.

S&F Extruded Aluminium, anodised, bow handles of size 150mm complete all as specified and directed.

S&F Extruded Aluminium, anodised, bow handles of size 100mm complete all as specified and directed.

S&F aluminium anodised barrel bolts and fixed of 200 mm length complete all as specified and directed.

S&F aluminium anodised barrel bolts and fixed of 100 mm length complete all as specified and directed.

S&F Mild steel sliding door bolt, plate type stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, length of bolt 300mm complete all as specified and directed.

S&F in repairs Vitreous China EWC with P or S Trap including seat cover closed pattern with flat bottom and cover and MS CP hinging device, PVC flush bend pipe incl PVC Flushing Cistern 10 LITRE capacity, Low Level Valve Less, Symphonic Action type, White, with Inlet, Ball Valve, Float and Handle including 32mm dia PVC Flush Pipe, a Pair of Cast Iron Brackets duly Painted/ Erecting Stand including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 including taking down unserviceable Flushing Cistern and connected Items of any description, complete all as specified and as directed.

S&F in repair Plastic Water closet seat cover, black/white closed pattern with flat bottom, and cover and mild steel chromonium plated or aluminised hinging devices, complete all as specified and directed. Make : Parrywire, Hindware or equvalent.

S&F in repair Vitreous china squatting pan, 'Orissa' pattern, size 580 X 440 mm white, with integral foot rests including provision of lime concrete bedding, fixing of flushing cistern complete all as specified and directed.

S&F in repair PVC valveless, syphonic action type flushing cistern, low level, white, 10 Ltr capacity with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair vitreous China clay wash hand basin of size 550x400mm with pedastal incl brackets for fixing complete all as specified and as directed

Taking up or down steel tubing and connections for 15 mm bore of pipes complete all as specified and directed.

Taking up or down steel tubing and connections for 20 mm bore of pipes complete all as specified and directed.

S&F GI steel tubing medium grade 15mm bore with all fitting and fixed complete to wall and ceiling or laid under in floor

S&F GI tubes, medium grade galvanised, 20mm bore with all fitting and fixed complete to wall and ceilings or laid in floors complete all as specified and directed.

Refixing old steel tubing and connections in new or old position to walls and ceilings or laid in floors, 15mm bore complete all as specified and directed.

Refixing old steel tubing and connections in new or old position to walls and ceilings or laid in floors, 20mm bore complete all as specified and directed.

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever barackets and connecting union to pipe overall size 495mmx420mm bowl size 410mmx330mmx160mm complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs washers and wastes incl bedding in CM to dwarf wall or incl fixing cantilever brackets and connecting union to pipe overall size 915x460 mm bowl size 410mmx360mmx160 mm complete all as specified and directed.

S&F in repair pillar taps cast copper alloy with capstan heads, chromium plated, fancy type,15 mm bore complete all as specified and directed.

S&F in repair Bip tap, chromium plated, 15mm fancy type, complete all as specified and directed.

S&F in repair Concealed stop cock, fancy type, chromium plated, 15 mm bore, complete all as specified and directed.

S&F in repair Angular stop cock, fancy type, chromium plated, 15 mm bore, complete all as specified and directed.

S&F PVC connections 15 mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair 15mm bore brass CP WHB mixer for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed. Make: Prayag/

S&F Tubular Towel rod, D type 60cm long brass Chromium plated complete all as specified and directed.

S&F Stainless steel kitchen plate rack of size 31" X 30' X 10" made out of stainless steel sheet of 1.00 mm with all accessories including taking down old unservicable rack complete all as specified and directed. Make : Blue star, Cat No - BSKPR-314

S&F rotational moulded polyepolyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 500 Ltrs incl taking down old unservicable tank of any capacity all as specified and directed

S&F rotational moulded polyepolyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of capacity 1000 Ltrs incl taking down old unservicable tank of any capacity all as specified and directed

Disconnecting existing tanks, setting aside for cleaninig and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc and hoisting if required reconnecting and rfixing in position of exc 500 ltrs & nexc 1000 ltrs complete all as specified and directed.

Disconnecting existing tanks, setting aside for cleaninig and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc and hoisting if required reconnecting and rfixing in position of exc 1000 ltrs & nexc 2000 ltrs complete all as specified and directed.

S&F in repair float valve of size 20mm, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe complete all as specified and directed.

S&F in repair float valve of size 25mm, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe complete all as specified and directed.

S&F in repair tank nipple suitable for HDPE water tank of size 15mm dia bore complete all as specified and directed.

S&F in repair tank nipple suitable for HDPE water tank of size 20mm dia bore complete all as specified and directed.

S&F Gun metal gate valve, 25 mm dia, class I (ISI) marked with iron wheel head, screwed both ends for iron pipe, suitable for following bore of pipe including taking down old existing unserviceable complete all as specified and directed by Engr-in-Charge

S&F in repairs Gun metal, 20 mm dia, gate valve class I (ISI) marked with iron wheel head, screwed both ends for iron pipe, suitable for following bore of pipe including taking down old existing unserviceable complete all as specified and directed by Engr-in-Charge

S&F PVC (SWR) bends, any radius, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) Pipes single socketed in any length with rubber ring joints, 110 mm bore fixed to walls complete all as specified and directed.

M&L Aluminium anodized frame for doors , windows , ventilators with one or more rebates incl joing cleat for fixing etc complete all as specified and directed.

S&F anodised aluminium window and ventilator shutters fixed type without sash bars, aluminium secton weighing 0.55 kg/m incl necessary joining cleats glazing clips, rubber packing , anodised aluminium snap beading , screws complete

S&F anodised door shutters , aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , handles 2 nos in each door , hinges , anodised aluminium snap beading screws etc complete all as specified and directed.

S&F anodised window and ventilator shutters side hung/sliding type without sash , aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing , anodised aluminium snap beading screws ,anodised aluminium fittings such as peg stays 150 mm long(1 no) hinges type B-21 100 mm long (2 no) suitable handle (1 no ) complete all as specified and directed.

S&F Sheet glass, 5.5mm thick ordinary quality, in squares,exceeding 0.50 sqm in each pane including rubber packing and aluminium beading complete all as specified and directed.

M&L 12mm thick prelaminated particle board, interior grade prelaminated both side with decorative choice laminations, fixed with screw etc., complete all as specified and directed.

S&F in repair Aluminium extruded section door closer hydraulially regulated,(ISI Marked), designation No 3, universal type suitable for door shutter of 851 to 1000mm width and of weight of between 61 to 80 kg and fixed complete all as specified and directed.

M&L for Wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashings and junction of parapets, etc., and surface painting, with a layer of blown bitumen of any penetration applied hot @ 1.7 kg per sq. m. blinded with grit or pea size gravel @ 0.006 cu. m per sq. m, and lightly tampered (area of flashings, etc., shall be added to the roof area) complete all as specified and directed.

M&L for mild steel joist channel or angle or tee section, ms tube and fixed with ms flat iron cut into shape drilled and fixed with screw conforming fe 410 complete all as specified and directed.

S&F in repair CP over head showers dia around 100 mm round shape single flow ( ABS body chrome plated with grey face plate ) with rubit cleaning system with CP shower arm dia 20 mm long round shape without bend for wall mounted showers wall flange etc complete all as specified and as directed. Make: Jaquar Cat.No OHS-CHR-1989 with SHA-CHR-49483 or equivalent model from make Hindware / Prayag.

S&F in repair CP single lever wall mixer 3-in-1 system with provision for bath hand shower and overhead shower with 115 mm long bend pipe connecting legs and wall flange ( without hand & overhead shower) etc complete all as specified and as directed. Make: Jaquar Cat.part No OPP-CHR-15125PM or equivalent model from make Hindware/ Prayag/ Parryware.

S&F in repair 15 mm bore health faucet cock with flexible pipe 1 meter long etc complete all as specified and as directed. Make: Jaquar Cat.part No ALD-CHR-565 or equivalent model from make Hindware/ Prayag/ Parryware.

S&F in repair CP soap dish holder fixed on wall with CP screws etc complete all as specified and as directed. Make: Prayag Cat.part No BA-05 or equivalent model from make Hindware /Parryware/ Jaquar.

S&F in repair stainless steel Toilet paper roll holder with fixed on wall with CP screws etc complete all as specified and as directed. Make: Jaquar Cat.part No AKP-35755PS or equivalent model from make Hindware/ Parryware/ Jaquar.

S&F in repair stainless steel Towel ring square shape with round flange with fixed on wall with CP screws etc complete all as specified and as directed. Make: Jaquar Cat part No ACN-CHR-1121N or equivalent model from make Hindware/ Parryware/ Prayag.

S&F in repair Sheet glass corner shelf assembly with ABC bracket complete all as specified and as directed. Make: Jaquar Cat Part No CAN-1173 or equivalent model from make Hindware/ Parryware/ Prayag.

S&F in repairs Vitreous China EWC including seat cover closed pattern single piece size 755x365x655 complete all as specified and directed. Make: Jaguar Cat Part No: LYS-WHT-38851PSM or equivalent Hindware/ Parryware/ Prayag.

M/S T N CONSTRUCTION

M/S UTTAM SAHA

MS HO Shadap

Bharara construction