Special Repairs to Bldg No T-37 (Septa), T-53 (ASC), and T-19/A-1,2 (Mortuary) at Aurangabad under GE (S) Ahmednagar

Amount

Demolition of cement concrete (un-reinforced) in ground floor and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles all as specified and as directed.

Taking down aluminium frame and shutters of doors, windows, ventilators of any type and partition including glass all as specified and as directed.

Taking down chowkats or frames, area n.exc 1.5 Sqm each (without taking off shutters from frames) all as specified and as directed.

Taking down chowkats or frame, area exc 1.5 Sqm but n.exc 4.5 Sqm each (without taking off shutters from the frames) all as specified and as directed.

Taking down trusses etc., any type and size of wooden/steel members, above 4m upto 8m span all as specified and as directed.

Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof coverings including ridges complete all as specified and as directed.

Dismantling single layer Mangalore pattern or similar tiles in roofing including ridge tiles all as specified and as directed

Dismantling wooden battens spaced exceeding 15cm for tiles, shingles etc of any size including tilting filets complete all as specified and as directed.

Dismantling boarding, any description, fixed in any position with nails all as specified and as directed.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section, in any position all as specified and as directed.

Dismantling stone slabs and tiles/ interlocking tiles etc of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar all as specified and as directed

Dismanlting floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and as directed.

Taking down cement or cement lime plaster on brick/stone walls etc. including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Excavation in trenches, n exc 1.50m wide and n exc 1.50m in depth; for foundations, etc. or for manholes etc not exc 10 Sqm on plan and not exc 1.5m in depth and getting out in soft/loose soil all as specified and as directed.

Returning, filling in (soil), including spreading, levelling, watering and well ramming in layers not exc 25cm thick all as specified and as directed.

Removing excavated soil to distance n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point all as specified and as directed.

M&L for cement concrete 1:3:6, type C1 using 20mm graded stone aggregates for fixing hold fasts and like all as specified and as directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed.

S&F 35mm thick second class hardwood factory made, plain, framed, panelled shutter (two panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated and fixed complete all as specified and as directed.

S&F 100 mm size butt hinges, medium weight, cold rolled mild steel, and fixed all as specified and as directed.

S&F 200mm long mild steel barrel tower bolts, stove enamelled black with bright bolt all as specified and as directed.

S&F 150 mm size mild steel pressed handle, oval type, stove enamelled black complete all as specified and as directed.

S&F 300 mm long, mild steel sliding door bolt, stove enamelled black with bright bolt, not less than 16 mm dia with & including a minimum of 6 bolts & nuts, four on bolt plate and two on staple plate complete all as specified and as directed.

S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and as directed.

S&F mild steel flat iron in wind ties for roof including securing bolts, nosing, posts/struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets including all necessary drilling holes, notching for wire etc conforming to Fe 290. Gde-165 complete all as specified and as directed.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/or rivetted or forged into spikes, framed guard bars and similar work conforming to Fe 290. Gde-165 complete all as specified and as directed.

S&F mild steel screw bolts, 11mm to 15mm dia (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 10 cm long all as specified and as directed.

S&F 1.25 mm thick mild steel plain black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and as directed.

S&F rolled mild steel joist, channel, angle or tee sections as in main and cross beams, hip and jack rafters; purlins etc fixed with angle cleats or other connecting plates conforming to Fe 410 -W (Gde-E- 250) quality-A complete all as specified and as directed.

S&F rolled mild steel plates (plain or chequred) channels, square cut or notched, forming holes, with riveted, bolted or welded attachment confirming to Fe 290. Gde-165 complete all as specified and as directed.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe 290 (Gde- 165) complete all as specified and as directed.

S&F mild steel framed work confirming to Fe 290. Gde-165 as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed.

S&F mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS.1161- 1979 grade St.-240 complete all as specified and as directed.

S&F mild steel windows with side hung shutters including projecting type hinges, steel handle and steel peg stay, complete with glazing bars, dovetailed or welded all as specified and as directed.

S&F mild steel windows with side hung shutters including projecting type hinges, steel handle and steel peg stay, complete without glazing bars, dovetailed or welded all as specified and as directed.

S&F mild steel ventilator, factory made with top hung shutter, including hinges, steel peg stays etc complete all as specified & as directed.

S&F aluminium powder coated frame for partitions with one or more rebates including joining cleats for fixing etc complete all as specified and as directed.

S&F powder coated aluminium door with frame and shutter in two panels (top and bottom) made out of aluminium sections (make Jindal or equivalent) including 5.5mm thick tinted glass, aluminium cleats, rubber/ neoprene beading, all necessary fittings and locking arrangements etc all as specified and as directed and comprises of following sections :- (a) Vertical style- 47 x 44.5 x 2.25 mm thick @ 1.15 Kg/m (Min) (b) Lock rail- 114.6 x 44.45 x 2.3mm thick @ 2.06 Kg/m (Min) (c) Bottom rail-114.6 x 44.45 x 2.3mm thick @ 2.06 Kg/m (Min) (d) Frame-47.5 x 44.45 x 2.25 mm thick @ 1.12 Kg/m (Min)

S&F in repairs double action floor spring hydrulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet, foundation box, main body with stainless steel cover, governing pivot made of brass other parts made of mild steel heavy duty and fixed complete all as specified and as directed.

S&F powder coated aluminum windows, three track, made out of aluminium sections (make Jindal or equivalent) including all necessary fittings, 5.5mm thick tinted glass, netlon jalli, rubber/ neoprene beading, locking arrangements all as specified and as directed and comprises of following sections :- (a) Window frame (i) Bottom-Section 20671 (Wt not less than 0.699 Kg/m) (ii) Top & Size - 20672 (Wt not less than 0.594 Kg/m) (b) Shutter (i) Vertical (end)- 20669 (Wt not less than 0.481 Kg/m) (ii) Vertical (lock) - 20689 (Wt not less than 0.481 Kg/m) (iii) Bottom - 20718 (Wt not less than 0.263 Kg/m) (iv) Top - 20668 (Wt not less than 0.377 Kg/m)

S&F prepainted galvalume aluminum zinc coating GI based corrugated steel sheets 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed.

S&F prepainted galvalume aluminum zinc coating GI based plain steel sheets 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ridges/cladding to wall, fixed with self tapping screws as specified and as directed.

S&F 9mm thick primium quality laminated PVC tiles 600mm x 600 mm in false ceilling, fixed with screws, including GI frame work for false ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to center/ intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900 mm center to center GI cleat and steel expansion fasteners with and including ceilling section (not exc 1.2m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm center to center frame work including hanger 6 mm dia GI wire upto 1200 mm length adjustable level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40x3mm size 60mm long including dismantling existing false ceiling boards,hangers & framework complete all as specified and as directed.

M&L for 75 mm thick PCC 1:4:8, type D2 (using 40 mm graded stone aggregates) as in sub-base complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregates) as in plinth protection, finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.

M&L for granite of any type work (table rubbed and polishing) in steps, jambs, pillars, window cill, cooking platform and like in cement mortar 1:4, including pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite complete all as specified and as directed.

M&L for machine cut kota stone flooring, 20-25 mm thick (size of kota stone slab 22"x22") laid over and including 20 mm thick bedding layer of cement mortar 1:6 jointed with grey cement slurry mixed with pigments to match the shade of slab including cutting, rubbing and mirror polishing including removing dust complete all as specified and as directed.

All as per serial item No. 48 here-in-before but 18 to 20 mm thick kota stone on vertical surfaces such as in skiting /dado of size as required at site over and including10 mm thick backing coat of cement mortar (1:4) complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exc 0.18 sqm but not exc 0.38 sqm, shade as approved by GE, as in floors etc., laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M&L for glazed coloured ceramic tiles 7mm thick (plain or printed), area of each tile exc 0.11 sqm but n exc 0.18 sqm, shade as approved by GE, as on vertical surfaces like dado, skirting etc laid over and including 10 mm thick backing coat in cement mortar 1:4, jointed in neat cement slurry and pointed in coloured cement to match with colour of tiles complete all as specified and as directed.

M&L for vitrified coloured ceramic tiles ,10 mm thick (square / rectangular), area of each tile exc 0.36 Sqm but n exc 0.42 Sqm, shade as approved by GE in floor etc laid over and including 15 mm thick bedding layer in cement mortar 1:6, jointed in grey cement slurry and pointed in white or coloured cement to match with colour of tiles all as specified and as directed.

All as per serial item No 52 above but in dado / skirting or on vertical surfaces, laid over and including 10 mm thick backing coat in cement mortar 1:4 .

M&L for 60 mm thick precast cement concrete interlocking tiles (glossy finish/ rubber matt finish) hydraulically pressed cemented tiles of grey colour with pigments, (glossy finish/ rubber mat finish) factory made, M-35 grade as in floor laid over & including 25 mm thick sand cushioning and including filling of interstices with fine sand complete all as specified and as directed. Note Size, shape & pattern of tiles shall be as decided.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces (external plaster), finished surfaces even and fair all as specified and as directed.

M&L for rendering 10 mm thick in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces (Internal plaster), finished surfaces even and smooth without using extra cement all as specified and as directed.

M&L for GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc in walls ceiling's stanchions beams etc including all laps cutting and waste all as specified and as directed.

Complete removal of existing treatment from old decorated plastered or unplastered walls including cornices, pillars, filling up undulations and applying 1.5mm thick (average) wall care putty on entire surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed.

M&L for preparing new plastered surface of walls and applying three coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whiting all as specified and as directed.

M&L for preparation of new plastered surfaces of walls applying two coats of cement base paint over a coat of primer all as specified and as directed

S&F 3mm thick figured glass, pin head type and glazing to steel window/ventilator with oil putty in square n exc 0.5 Sqm in each pane all as specified and as directed

S&F 5.5mm thick tinted sheet glass, as in glazing to partition in square exc 0.5 Sqm in each pane fixed with and including rubber gasket and aluminium beading etc complete all as specified and as directed

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old treating small articles such as stops, covers, gully, gratings, holdfasts, ends of posts, backs of chowkats, etc., area n exc 0.1 sq. m each and treated with tar or coal tar black paint all as specified and as directed

M&L for preparation of new wood or wood based surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over one coat of pink primer complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified and as directed

M&L for 15mm bore, GI steel tubing, medium grade, with and including all fittings and fixed complete to walls or laid in floors including taking down existing GI tubing with fittings complete all as specified and directed.

M&L for 20mm bore, GI steel tubing, medium grade, with and including all fittings and fixed complete to walls or laid in floors including taking down existing GI tubing with fittings complete all as specified and directed.

S&F in repairs, 15mm bore bib taps, cast copper alloy fancy type chromium plated, with crutch or butterfly handles, screwed down for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repairs, 15mm bore stop valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or unions complete all as specified and as directed.

S&F in repairs, 20mm bore, stop valves, cast copper alloy, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F in repairs, 32 mm bore low density polythene pipe (LDPE) of pressure rating 6Kgf/sqcm fixed to wall or laid in floor etc including fittings complete all as specified and as directed.

S&F in repairs, 125mm size, brass chromium plated swivel shower rose, including shower arm fixed to steel pipe and union, complete all as specified and as directed.

S&F in repairs, 125 mm dia grating doom with waste hole of PTMT (Minimum weight 40gms) and fixed complete all as specified and as directed.

S&F in repairs, vitreous china wash hand basin, white, flat back, size 580 mm x 450 mm including brackets, pillar tap 15 mm bore chromium plated, fancy type, cast copper alloy with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe,15mm dia PVC connection pipe complete all as specified and as directed.

S&F in repairs, vitreous China, white, squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest, P or S trap, set in cement concrete including flush pipe and connecting to trap / flushing cistren and making good to floor complete all as specified and as directed.

S&F in repairs, vitreous China wash down water closet (pedestal pattern), white, including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap with and including white or black seat cover for pedestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed.

S&F in repairs, 450mm long PVC Connection, 15mm size with PTMT nuts complete all as specified and as directed.

S&F in repairs chromium plated health faucet with 1 metre flexible tube & hook complete all as specified and as directed.

S&F in repairs, sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long and fixedwith brass screws complete all as specified and as directed

S&F in repairs, wall corner sheet glass shelf assembly, size 12"x12" with 5mm thick toughned glass with all fittings and fixed with brass screws complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 1000 litres capacity, tripple layered, hoisted and fixed in position including 20 mm bore ball valves, high pressure, PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed, (Minimum weight 142 gms,) screwed to iron pipe and connecting, including taking down existing water tank with connected fittings complete all as specified and as directed.

S&F in repairs, tubular towel rail, 20mm dia, D type, 60cm long between flanges, brass chromium plated, fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed.

S&F in repairs, PVC low level flushing cistern, 10 litre capacity including ball valve, bracket, inlet, PVC pipe, PVC connection 600 mm long etc.complete all as specified and as directed.

S&F in repairs, 75 mm bore, PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or under floors complete all as specified and as directed.

S&F in repairs, 110 mm bore, PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid in trenches or under floors complete all as specified and as directed.

S&F in repairs, 75 mm bore PVC (SWR) bends any radius with access door complete all as specified and as directed.

S&F in repairs, 110 mm bore PVC (SWR) bends any radius with access door complete all as specified and as directed.

S&F in repairs, 75 mm dia PVC(SWR) nahani/floor trap with grating including jointing to waste pipe with solvent cement complete all as specified and as directed.

Taking down carefully any type of point wiring (light, fan, bell, socket or power), complete excluding light fittings but including switches, ceiling roses, pendants, regulators, sockets, etc. and making good disturbed surfaces of walls, ceiling, floors etc to match with existing surface complete all as specified and as directed.

M&L for point wiring complete on surface of wall (open) type with two runs of 1.5 sqmm for phase and neutral, single core, multi-stranded copper conductor cable of 1100 Volts grade, PVC insulated and unsheathed , FRLS cable drawn through and including PVC casing and caping (ISI marked) of suitable size and its accessories such as Tee, elbow, jointer, elbow corner etc. fixed on surface of walls, coloumns/ beams alongwith 1.5 Sqmm copper conductor cable (multi-stranded), PVC insulated and unsheathed FRLS cable as earth wire connected to common earth dolly at one end and metalic bodies of luminaire/ fan at other end including PVC folding boards for mounting switches, sockets, fan Regulators, accessories etc for one light/fan point controlled by one, one way switch all as specified and as directed. NOTE: 1.Proper colour coding shall be adoptd for wiring (for phase-RED,YELLOW,BLUE & for Earth-Green and Neutral-Black) 2. All points shall be earthed up to fixtures i.e holders,tube lights,all lights,ceiling lights,bulkhead lights,bldg security lights etc.)

All as per serial item No 92 but for 5 Amps socket in same board complete all as specified and as directed.

All as per serial Item No 92 but for 5 Amps socket in independent board complete all as specified and as directed.

All as per serial item No 92 but for power point 3 pin switch socket, 15/16 Amp with PVC copper conductor cable multistrand unsheathed 2.5 Sqmm on independent board including one run 1.5 Sqmm multistrand PVC copper conductor cable for earth continuity in and including PVC casing and caping fixed on wall including 2mm thick PVC box complete all as specified and as directed

S&F modular switch, single pole, one way, 6/10 Amps, 1 module complete all as specified and as directed.

S&F modular switch, single pole, one way, 15/16 Amps, 1 module complete all as specified and as directed.

S&F modular socket, 6 amp 2/3 pin, combined, 2 module complete all as specified and as directed.

S&F modular socket, 6 A/16 amp 2/3 pin, combined, 2 module complete all as specified and as directed.

S&F ceiling rose, surface bakelite, three terminal type complete all as specified and as directed.

S&F lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

S&F in repairs, LED lights fitting 1x 18W, 220V, AC, decorative box type with driver, holder including LED tube light, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F in repairs, LED light fitting mirror type with high out put diffuser 2 feet, 5 watt 220 V AC, decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F in repairs, LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser, soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

S&F in repairs, round shape 15 watt, 220 volts, AC, recessed type with high efficiency PMMA diffuser, soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F in repairs, 35/40 Watt, building mounted LED Security light fitting complete made up of pressure die cast housing with toughned glass and individual high power LEDs with secondary optics, IP66 protection and impact resistance of IK07 & 10KV external SPD, including GI bracket made out of GI pipe 40/50 mm bore, medium grade pipe 1.2 m long bend to shape required, fixed to pole / wall with 02 Nos MS clamps made out of flat iron 40 x 5 mm including nuts, bolts and washer, painting with two coats aluminium paint over a coat of primer, suitable for LED fitting, complete all as specified and as directed.

S&F in repairs, lamp LED 9/10 Watt, 230 volts, 50 Hz AC complete all as specified and as directed.

S&F in repairs, sheet metal enclosure (Factory made), double door shutter type for distribution board (when MCBs are to be used), Tripple pole and neutral, 415 volts, 4 way, protection class IP-42, suitable for fixing MCBs, Isolators etc, confirming As per IEC 61439-3, suitable for flush mounting and surface mounting, with 100 Amps rated copper busbar, with Neutral bar, Earthbar and cable alley for cable managment, fully shrouded, Neutral bars, prefittes masking sheet complete all as specified and as directed.

S&F in repairs, sheet metal enclosure (Factory made), double door shutter type for distribution board (when MCBs are to be used), single pole and neutral, 240 volts, 8 way, protection class IP-42, suitable for fixing MCBs, Isolators etc, confirming As per IEC 61439-3, suitable for flush mounting and surface mounting, with 100 Amps rated copper busbar, with Neutral bar, Earthbar and cable alley for cable managment, fully shrouded, Neutral bars, prefittes masking sheet complete all as specified and as directed.

S&F in repairs, MCB SP, AC 240 V, 6 to 32 Amps, 10 KA capacity ,'c' series, making connection with suitable size of copper lugs etc complete all as specified and as directed.

S&F in repairs MCB TPN, AC 415 V, 63 amps, 10 KA capacity ,'C' series, making connection with suitabl size of copper lugs etc complete all as specified and as directed.

S&F in repairs, MCB SPN (DP) 240 volts, 40 to 63 Amps ,'c' series, making connection with suitable size of copper lugs etc complete all as specified and as directed.

S&F in repairs, MCB TPN 415 volts, 100 Amps, ,'c' series, making connection with suitable size of copper lugs etc complete all as specified and as directed.

S&F in repairs, sheet metal enclosure, SPN with 2 pin and earth plug and socket complete with and including single pole, 20 Amps MCB, 240V all as specified and as directed.

Supply, laying, jointing and testing PVC XLPE insulated armored heavy duty electric cable with aluminum conductor, 1100 volt grade, cross sectional area 50 Sqmm, 3.5 core, laid in trenches/ fixed on wall including electric connections on both ends with suitable lugs,binding wire including taking down existing cable all as required at site all as specified and as directed

M&L for dry river sand in trenches for cushioning (8 cm below the cable and 15 cm above the cable) of underground cable including spreading, levelling, hand punning complete all as specified and as directed. Note:Punned thickness will be measured and paid.

Supply and laying in replacement of un-reinforced precast concrete cable cover, class LV type-1, flat, size 250 mm x 150 mm x 40 mm complete all as specified and as directed.

S&F in repairs, GI tubing, light grade, 40 mm bore dia for cable protection on pole/wall/floor/ or in trenches and drain etc complete with necessary clamp, nut, bolts and washers and socket and making good the disturbed surface of wall , floor or roof etc all as specified and as directed.

M&L for sub main wiring with 2 runs of 4.0 sqmm, single core, PVC insulated & unsheathed cable, conforming to IS-694, 1100 volts with copper conductor, multi stranded, drawn in and including suitable size PVC Casing Caping (ISI marked) with all accessories such as Tees, Elbows, junction box etc as requied alongwith one run of 4.0 sqmm single core PVC insulated & unsheathed copper conductor as continuous earth wire dolly and connecting to existing main switch board / distribution board of each building as ordered and testing on completion including taking down old submain wiring and any type of casing/caping/Conduit, complete all as specified and as directed. Note : Three runs of 4.0 Sqmm cable and one run of PVC casing/caping will be measured as one Rm unit .

M&L in repairs/replacement earthing complete with galvanized steel earth plate electrode 60 cm X 60 cm X 6.0 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level, connecting to the GI wire 4 mm dia , by means of nut bolts, check nuts and washer of the GI . Earth wire connected upto main earth point/DBs alongwith 15mm dia GI pipe, medium grade, including provision of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregates with 40 mm thick RCC (1:2:4) cover with reinforced with XPM (weight not less than 4 Kg / Sqm) and frame of angle iron 25mm X 25 mm X 3mm with lugs 2 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding than 50 mtr, all as per electric plate No 3 of SSR Part I 2009 and connection to earth test point all as specified including testing on completion.