Interior and Furnishing Work of The Secretariat Building (GF and FF) At Moti Daman. (E-30450)

Civil works others

Providing and Fixing of Full height Partly Glass & Partly Flush Partition.(Veneer Finished)(Min 3000mm ht) made Solid part of partition made from Aluminium frame work shall comprise of 50mm x 50mm x 1.6mm thk members aluminium section (weight not less than 0.836 kg/rmt)at regular distance of 450 to 600mm c/c both ways (As per drawing) and both side covered with 8mm th Marine Ply & 4mm thk Approved Veneer Cladding with groove pattern & Finished with required teak wood Beading , teak wood exposed frame pattern with melamine Polish. Partly Part of partition fixed 8mm thk Toughened glass Panel with Beading as per Drawing Rate also including 75mm x 75mm teak wood Door Frame with polish & Partly fabric Paneling , Partly Wall Paper , Partly Gypsum Paneling with Paint Finish & all necessary hardware.etc.The rate should also include of Applying anti-termite and anti- borer paint to wooden frame work wherever Required as per directed . & Applying three or more coats of melamine polish /painting of approved quality and shade to have desired, finish to all exposed surface of teak wood members beadings, board, groove pattern etc. including preparing of surface by sand papering, applying putty etc. complete(Quantity measured on elevated part at bottom of ceiling level & Door will be measured and paid separately)

Providing and Fixing of Full height Partly Glass & Partly Flush Partition.(Laminate Finished)(Min 3000mm ht) made Solid part of partition made from Aluminium frame work shall comprise of 50mm x 50mm x 1.6mm thk members aluminium section (weight not less than 0.836 kg/rmt)at regular distance of 450 to 600mm c/c both ways (As per drawing) and both side covered with 8mm th Marine Ply & 1mm thk Approved Laminate Cladding with groove pattern & Finished with required teak wood Beading , teak wood exposed frame pattern with melamine Polish. Partly Part of partition fixed 8mm thk Toughened glass Panel with Beading as per Drawing Rate also including 75mm x 75mm teak wood Door Frame with polish or Laminate cladding as per Directed & Partly fabric Paneling , Partly Wall Paper , Partly Gypsum Paneling with Paint Finish & all necessary hardware.etc.The rate should also include of Applying anti-termite and anti- borer paint to wooden frame work wherever Required as per directed . & Applying three or more coats of melamine polish at Exposed Teak wood Frame of approved quality and shade to have desired, finish to all exposed surface of teak wood members beadings, board, groove pattern etc. including preparing of surface by sand papering, applying putty etc. complete(Quantity measured on elevated part at bottom of ceiling level & Door will be measured and paid separately)

Providing & fixing of Full height Flush Partition.Veneer Finished (3000mm ht) made from Aluminium frame work shall comprise of 50mm x 25mm x 1.2mm thk members at regular distance of 450 to 600mm c/c both ways (As per drawing) and both side covered with 8mm th marine Ply & 4mm thk Approved Veneer Cladding with groove pattern & Finished with required teak wood Beading , teak wood exposed frame pattern with melamine Polish. Rate also including 75mm x75mm teak wood Door Frame with polish & Partly fabric Paneling , Partly Wall Paper , Partly Gypsum Panelling with Paint Finish & all necessary hardware.etc.The rate should also include of Applying anti-termite and anti- borer paint to wooden frame work wherever directed . & Applying three or more coats of melamine polish /painting of approved quality and shade to have desired, finish to all exposed surface of teak wood members beadings, board, groove pattern etc. including preparing of surface by sand papering, applying putty etc. complete (Quantity measured on elevated part at bottom of ceiling level & Door will be measured and paid separately)

Providing & fixing of Full height Flush Partition.Laminate Finished (3000mm ht) made from Aluminium frame work shall comprise of 50mm x 25mm x 1.2mm thk members at regular distance of 450 to 600mm c/c both ways (As per drawing) and both side covered with 8mm th marine Ply & 1mm thk Approved Laminate Cladding with groove pattern & Finished with required teak wood Beading , teak wood exposed frame pattern with melamine Polish.or Laminate Cladding As per Directed Rate also including 75mm x75mm teak wood Door Frame with polish or Laminate Cladding as per Drawing & Partly fabric Paneling , Partly Wall Paper , Partly Gypsum Panelling with Paint Finish & all necessary hardware.etc.The rate should also include of Applying anti-termite and anti- borer paint to wooden frame work wherever Required & directed . & Applying three or more coats of melamine polish at exposed Teak wood Member of approved quality and shade to have desired, finish to all exposed surface of teak wood members beadings, board, groove pattern etc. including preparing of surface by sand papering, applying putty etc. complete (Quantity measured on elevated part at bottom of ceiling level & Door will be measured and paid separately)

Providing & Fixing of 75mm th.Gypsum Solid Partition Above False ceiling to Slab Bottom level , using Aluminum tube frame work shall comprise of 50 mm x 25 mm Aluminum tube (Medium Gauge, Jindal Make) placed at regular distance of 600mm C/C on both way partition witch includes one layer on each side of tapered edge 13mm thick (both side of partition) Gypsum board screw fixed with drywall screws of 25mm at 300mm c/c to as per above Specs, complete as shown in the drawing & design or as directed by Engg-in-charge.

Providing & fixing Full height Storage Cabinet Veneer Finish (2600 mm ht. & depth 425 or as required) Cabinet made from 18mm th.ply finishedmarinewith 4mm th Approved Veneer from out side & inside of storage 19mm th. ply with Laminate & Shutter Making with 19mm Plywood with Required Frame work as per drawing & shutter operated on auto closing hinges, The storage shall have suitable size edge teak wood beading or The bottom of the storage unit to be provided above 19 mm Block board skirting of skirting height. The cost shall be inclusive of all locks, SS tower bolts, handles, SS hinges, magnetic catchers and all hardware as per direction /schedule of interiors, furniture finishes. The storage shall be inside finished with 1 mm thk laminate of approved shade and All exposed edges to be finished with Veneer with melamine polish & Cabinets will have individual locking arrangement, & with necessary hardware etc Complete as shown in the drawing & design or as directed by Egg-in-charge

Providing & fixing Full height Storage Cabinet Laminate Finish (2600 mm ht. & depth 425 or as required) Cabinet made from 18mm th. Marine ply finished with 1mm th Approved Laminate from out side & inside of storage 19mm th. ply with Laminate & Shutter Making with 19mm Plywood with Required Frame work as per drawing & shutter operated on auto closing hinges, The storage shall have suitable size edge teak wood beading or The bottom of the storage unit to be provided above 19 mm Block board skirting of skirting height. The cost shall be inclusive of all locks, SS tower bolts, handles, SS hinges, magnetic catchers and all hardware as per direction /schedule of interiors, furniture finishes. The storage shall be inside finished with 1 mm thk laminate of approved shade and All exposed edges to be finished with Veneer with melamine polish & Cabinets will have individual locking arrangement, & with necessary hardware etc Complete as shown in the drawing & design or as directed by Egg-in-charge

Providing , Fixing & Erecting Full Height Display cabinet (3000mm Ht) 450mm to 600mm deep storage cabinet made from 18mm th. marine ply wood finished with 4 mm thk veneer with melamine polish from all Exposed surfaces with all required Teak wood Beading, Frame work etc. & in side of storage made from 19mm ply & Partly shutters & Partly Open Cabinet as per Drawing Shutter operated on auto closing hinges with glass profile shutter , 19mm thk ply to be providing for self as per detail . Storage will have individual locking arrangement & necessary hardware like SSmat finish handles/ ball catch. Complete as shown in the drg. & Design or as directed by Engg-in-charg.

Providing & fixing 38mm thk Jamb Line Paneling Venner Finish (75mm to 250mm Wide & 38mm thk) Jamb line to consist of 19 mm th +19mm thk Marine plywood Finished with 4mm Thk Veneer & Border Seal with Teakwood /or Veneer Cladding with melamine polish with required frame work / teak wood beading patty & Grove pattern at wall surfaces, Partition edge as per required & suggested Area.Cost including for All necessary hardware & polishing work complete as per Directed by Engg- in - charge.

Providing & fixing 38mm thk Jamb Line Paneling Laminate Finish (75mm to 250mm Wide & 38mm thk) Jamb line to consist of 19 mm th +19mm thk Marine plywood Finished with 1mm Thk Approved Laminate & Border Seal with Teakwood /or Laminate Cladding with required frame work / teak wood beading patty with Melamine Polish & Grove pattern at wall surfaces, Partition edge as per required & suggested Area.Cost including for All necessary hardware complete as per Directed by Engg- in - charge.

Providing & fixing Dacorative Planter Box Veneer Finish ( 200mm to 300mm wide & 450mm Ht ) Planter making from 19mm th Marine plywood with required teakwood & ply wood frame work as per detail & making niche for Applying Artificial plant , dacorative Pabble etc , all external Surfaces of Planter finished with 4mm veneer with Melamine Polish including required Hardware etc Complete as shown in Drawing or as per directed by engg in charge.

Providing , Fixing & Erecting Full Height Reception Back wall Partition(3000mm Ht) 200mm to 300mm width Partition Making from 18mm th. Marine ply wood finished with 4 mm thk veneer with melamine polish from all Exposed surfaces with all required Teak wood Beading, Frame work , & partly MOCA Stone cladding, 12mm thoghned Glass cladding etc. & Making dacorative Niche for LOGO & LETTERS , Arrangement of Electrical lighting Point etc Niche from 19mm ply as per Drawing & necessary hardware Complete as shown in the drg. & Design or as directed by Engg-in-charg.

Providing & fixing of Rock wool insulation in Dry Partition using Ready Made mineral wool slabs rock wool having density of 50kg / M³ with thickness of insulation is As per Directed By Engineer in Charge Duly packed in non woven fabric bag or HDPE Bag in dry partitions as per required & suggested area insulation work is complete as per Architect suggestion

Providing & fixing 12 mm thk.Single Shutter Toughned Glass door with edge polished fixing with first quality patch fitting double action floor springs on shutter at bottom efficient Dorma Make (Heavy duty)fixed into floor (including cutting for floor and repairing afterwards), with two pairs of 600 mm long 25 mm dia matt finished SS handles, two pair of concealed shoot bolts 250 mm long and pin type narrow style lock,on shutter with all necessary hardware. complete as per the drawing & design or as directed Engg-in charge. including Dorma Make Floor Spring

Providing & fixing 12 mm thk.Double Shutter Toughned Glass door with edge polished fixing with first quality patch fitting double action floor springs on each shutter at bottom efficient Dorma Make (Heavy duty) fixed into floor (including cutting for floor and repairing afterwards), with two pairs of 600 mm long 25 mm dia matt finished SS handles, two pair of concealed shoot bolts 250 mm long and pin type narrow style lock,on Each shutter with all necessary hardware. complete as per the drawing & design or as directed Engg-in charge. including Dorma Make Floor Spring

Providing & fixing 12mm thk .Wall paneling to consist of 12 mm th plywood finished with 4mm Thk Veneer & melamine polish with required frame work with teak wood beading patty &12 mm Marine plywood backing grove pattern at wall surfaces, Partition edge as per required & suggested Area.Cost including for All necessary hardware & polishing work complete as per Directed by Engg- in - charge.

Providing & fixing 19mm thk .Wall paneling to consist of 19 mm th plywood finished with 4mm Thk Veneer & melamine polish with required frame work with teak wood beading patty &19 mm plywood backing grove pattern at wall surfaces, Partition edge as per required & suggested Area.Cost including for All necessary hardware & polishing work complete as per Directed by Engg- in - charge.

Providing & fixing 50mm thk Box paneling to consist of 19 mm th plywood finished with 4mm Veneer with required frame work with teak wood beading patty & 19 mm plywood Box pattern at wall surfaces, Partition edge as per required & suggested Area.Cost including for All necessary hardware & polishing work complete as per Directed by Engg- in - charge.

Providing & fixing 12mm thk un finished plywood paneling to consist of 12mm th Marine plywood with required ply wood frame work with paint finish or as per Sujested by engg -in charge & border seal to teak wood beading patty with polishing on edge at wall surfaces,as per required & suggested Area.with All Necessary hard ware, etc.

Providing & fixing 19mm thk un finished plywood paneling to consist of 19mm th Marine plywood with required ply wood frame work with paint finish or as per Sujested by engg -in charge & border seal to teak wood beading patty with polishing on edge at wall surfaces,as per required & suggested Area.with All Necessary hard ware, etc.

Providing and supplying Acoustical Wall cladding with square edges made of fibre glass substrate 10mm thick and wrapped on the front side with an acoustically transparent and classified for Fire reaction Class A, as per ASTM E‐84, fabric with an option of colors – Husk, Copper, Sangria, Sesame, Coffee, Charcoal, Titanium, Flame, Peanut and Shell as per the choice of the Architect of size 600x600mm, 600x1200mm providing a minimum sound absorption level of 0.85 NRC to be affixed to wall using Wall panel Impalers supplied by Ceiling Solutions and construction adhesives as per the instructions laid down by the manufacturer. Installation : In order to fix the panels to the wall, the Impalers shall be fixed to the wall surface using self tapping screws. 3 nos. in case of 600x600mm and 4 nos in case of 600x1200mm wall panel Impalers to be used for the installation purpose. Silica based construction adhesive to be dabbed on to the projecting elements (spikes) of the impalers. Optra wall panels shall be pierced through the spikes of the impalers ensuring the line and level of the panels are maintained. Installation to be carried out by Trained Installation team & Installation should be carried out as per recommended procedure.

Providing and fixing of 6mm thick back painted Glass (premium GRIHA rated lacquered glass from Saint-Gobain) of approved color by Architect/ Client/Customer, fixed with SGG Glassmate Ultrafix (compatible neutral core silicon/double sided tape) on a perfectly leveled 12mm thick water proof marine plywood / MDF / Mineral fibre board which is mounted on the RCC wall/any other structure. Lacquered glass must be made industrially (via curtain coating process); opaque (if viewed against a support wall), coated with PU lacquer; color consistency (measured by Minolta spectrophotometer CM5081); highly durable (passes PERSOZ hardness test for minimum 220 oscillatios); humid resistant (conforms to BS EN 1036 1999); environmentally friendly (no lead, no arsenic, no copper, noformaldehyde); appropriate recycled content (12% post industrial / 6% post consumer); compressive strenght (1000 MPa) & tensile strenght (40 MPa),same as float glass. all complete as per direction of Engineer-in-Charge.

Providing & fixing Artificial Leather cladding over wooden partition/panelling fixed with Gripper & U-form ,Leather make & shade approved by Architect/ Client Complete work to give bubble free uniform surface. Any unevenness of the base surface shall be removed before fixing the Leather covering as per approved by Eng in charge. complete in all respects and the entire satisfaction of Architect and Engineer-in-charge.

Providing & fixing Fabric cladding over backing of u form sheet with 12 mm MDF paneling with required frame work as per drawing or wooden partition/panelling fixed with Gripper. Fabric make & shade approved by Architect/ Client Complete work to give bubble free uniform surface. Any unevenness of the base surface shall be removed before fixing the Fabric as per approved by Eng in charge. complete in all respects and the entire satisfaction of Architect and Engineer-in-charge.

Providing and fixing vinyl or Polyster Textile wallpaper coverings with approved adhesive on existing plastered surface finished with putty, to give bubble free uniform surface. Any unevenness of the base surface shall be removed before fixing the wall covering as per approved design, complete in all respects and the entire satisfaction of Architect and Engineer-in-charge.

Providing and fixing Gypsum false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45 x15 x 0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffuser, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge Gypsum moisture resistant board. (Cost including For suspended from RCC Ceiling /Roof, light cutting gala & also including Scaffolding & Working Platform for any height)

Providing and fixing Armstrong (CLASSIC LITE RH 99) (Silhautte grid) 16mm false ceiling system manufactured by Armstrong using hot dipped galvanized steel section, rotary stitched main tee of size 15mm x 45 mm web height, having 0.36 mm gauge at every 600 mm centre to centre maximum and rotary stitched cross tee of size 15 mm x 45 mm, having 0.33 mm gauge at every 600 mm. c/c. and wall angle of size 19 x 19 mm., having 0.35 mm gauge fixed to the periphery of the wall. The above grid is suspended at every 600mm c/c. in both directions using 2.0 mm. thick per-straightened GI wire laying CLASSIC LITE RH 99 ceiling tiles with Silhautte grid manufactured by Armstrong , having Humidity Resistance of 99%, RH and size 600mmx600mmx16mm over the formed grid complete. including light fixtures cutting gala in ceiling. & also including Scaffolding & Working Platform for any height)

Providing and fixing Armstrong Techzone Ceiling (Silhautte grid) 16mm false ceiling system manufactured by Armstrong using hot dipped galvanized steel section, rotary stitched main tee of size 15mm x 45 mm web height, having 0.36 mm gauge at every 600 mm centre to centre maximum and rotary stitched cross tee of size 15 mm x 45 mm, having 0.33 mm gauge at every 600 mm. c/c. and wall angle of size 19 x 19 mm., having 0.35 mm gauge fixed to the periphery of the wall. The above grid is suspended at every 600mm c/c. in both directions using 2.0 mm. thick per-straightened GI wire laying ("Tech zone Ultima " 6'' X 48'') (600mm x 1200mm & 300x1200mm) ceiling tiles with Silhautte grid manufactured by Armstrong , having Humidity Resistance of 99%, RH and size 600mmx1200mmx16mm over the formed grid complete.(Cost including For suspend1mtr.from RCC Ceiling /Roof with required MS Support, light cutting gala & also including Scaffolding & Working Platform for any height)

Providing & fixing Vertical Linear Baffle Ceiling (Metalium Make) made out of Aluminum Extrusion in Aluminum alloy grade 6063. The baffle blade shall be in size of 100x50x3600mm in powder coated to Wood grain finish – Red Oak & Cherry. The baffle blade shall be suspended using Slotted U-profile of 20 x 30mm at on-center spacing 100mm. Longer lengths of Baffle to be connected by Baffle Joiner and the ends to be installation of U-Grid: The U profile to be suspended at every 1200mm on-centre using 6mm threaded rod from the structural soffit using U-profile hanger. U-profile splice to be used to join more than one U profiles of length 3.75M. 1st U-Grid Channel must be no more than 400mm from the perimeter Fixed with End caps. Installation of Baffles: Locate the slot for Baffle Hangers in U Profile section at 1200mm centers. Hangers are inserted into the slot, and then inserted in the provision in the Al baffle. Two baffle hangers are required one on each side of the U-profile to hold the Al baffle in its place. Each Hanger to be secured into position by inserting the Locking Clip. When doing continuous installation, Baffles blades are to be connected at ends with Baffle Joiner, which are inserted into the top and bottom slots of the Baffle closed profile for alignment only. The bottom Joiner to be located first and fastened on one side only. The top Joiner to be fitted then and secured with grub screws on one side. Then the two Baffle sections shall be joined and the top Joiner is screw fastened on the 2nd Baffle profile. End Caps to be located by pushing the End Cap tongues into open Baffle slots. Installation to be carried out by Trained Installation team & Installation should be carried out as per recommended procedure.

Providing, Fixing,and Commissing Stretch Ceiling White translucent fabric with led aluminium base bar led light of osaram led lens 24 watt system with installation including sacffloding and staging complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.

Providing, Fixing,and Commissioning Veneer Finished Wooden Ceiling Making from 12 mm thick plywood (IS 710 ) as per drawing & instruction of EIC/architect& sample approved (complete with Teak wood frame work as per Drawing ).Ceiling finish with 12mm Plywood with Veneered MDF board and 4mm thk veneer with melamine polish finish. Plywood shall be fixed with required fabrication work and ply frame work with all necessary accessories & Hardware Rate shall include cost of making of all cutouts for light fixtures, gadgets,pelmets, grooves,and also provide support/template where ever required The rate shall be in sq.mt for all floors and at all heights including all costs the sample mock of 5 Sqm minimum of the frame work and ceiling) shall be approved from client/architect.5mm Groove shall be provided at the junction of the false ceiling & the wall. The rate shall be in sq m for all floors and at all heights ,Off sets whether hollow or solid in the ceilings including all costs. etc. completed as per as per drawing & instruction of Architect and Engineer-In-charge.

Providing, Fixing,and Commissioning Laminate Finished Wooden Ceiling Making from 12 mm thick plywood (IS 710 ) as per drawing & instruction of EIC/architect& sample approved (complete with Teak wood frame work as per Drawing ).Ceiling finish with 12mm Plywood with 4mm MDF board and 1mm thk Laminate finish. Plywood shall be fixed with required fabrication work and ply frame work with all necessary accessories & Hardware Rate shall include cost of making of all cutouts for light fixtures, gadgets,pelmets, grooves,and also provide support/template where ever required The rate shall be in sq.mt for all floors and at all heights including all costs the sample mock of 5 Sqm minimum of the frame work and ceiling) shall be approved from client/architect.2mm Groove shall be provided at the junction of the false ceiling & the wall. & Groove Finished with Polish match with laminate.The rate shall be in sq m for all floors and at all heights ,Off sets whether hollow or solid in the ceilings including all costs. etc. completed as per as per drawing & instruction of Architect and Engineer-In-charge.

Providing & Fixing 3M Etching LUMAR FILM including Plotter cutting. (Scotchcal™ ElectroCut™ Graphic Film Series 7725SE-400, Fluorescent Film) .complete in all respects and the entire satisfaction of Architect and Engineer-in-charge.

Providing & Installing Pictogrames & Signages for Locating the area as per design & drawings to the complete in all respects and the entire satisfaction of Architect and Engineer-in-charge.

Providing and fixing Printed Vinyl with Lamination Graphic design, 3M Make complete as per suggestion of Architect/Client. If in case any application finishing will not as per satisfaction contractor shall remove all film at their cost. Contractor shall do a sample mock of 5 Sqm minimum of glass film) , Design shall be approved from Architect/Client.

Providing and Supplying & Fixing of Design Brick wall cladding with required chemical with epoxy grout if required as per approved shade. Complete Cladding work on Wooden Partition, Brick wall or as per required area Complete with All required Scaffolding, staging, Ahdhesive Material ,Hardware etc.Complete Cleaning Smooth sarface , Remove all dust, Mortar, Chemical etc after work done

Providing and fixing Dimout Blinds Blackout (Zebra blinds / Hunter douglas) construction100% Polyester fabric weight 197 GSM with repeated fabric size:Solid11.5cm/Mesh 7.5cm fabric is fixed on Anodized extruded grooved tube size 40mm O.D, the control unit is made of high strength reinforced plastic with a clutch of wrap spring design and high carbonsteel spring design . The control unit and idler should be mounted in in cassette type powder coated Headrail (As per approved sample to the entire satisfaction of Engineer-in-Charge)

Providing and fixing Roller blinds 100% Blackout (Zebra blinds / Hunter douglas) , construction 3 ply PVC and1 ply Glass fibre fabric thickness 0.36 mm and weight +-520 GSM, Fire resistance NFPA 701, AATCC 16-2003 4.5 and Green guard certified with Anti fungal and Anti bacterial fabric The control unit is made of high strength reinforced plastic with a clutch of wrap spring design and high carbon steel spring design provided to transmit motion from driving to driven members of clutch The control unit and idler should be mounted on powder coated aluminium Headrail with M.S bracket to keep the fabric in Tension and straight (As per approved sample to the entire satisfaction of Engineer-in-Charge)

Providing, Applying, of Wall painting three coats with Royal touch Plastic paint ( Anti bacterial Paint )of Asian Paint or equivalent approved make list or approved by architect and engineer in any shades and colour as directed on wall surface to give an even shade including applying two coats of Acrylic co‐polymer Stucco putty of Brila or equivalent on a one coat of PVA prmer/Decoprime or equivalent and three coats of paint, scaffolding to at any height with all labour and material thoroughly brushing the surface free from morta droppings and other foreign matter and sand prepared smooth etc. complete. Top coat should have. The substrate must be sound, clean, dry, free from dust, oil, grease and laitance etc. All traces of release agents must be removed. On chalky and dusty surfaces, all loose material must be removed by stiff bristle brushing. The primer / paint application is to be done with the rollers. rate shall be including crack filling and levelling as per manufacturers specfication complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge.

Providing and fixing Pelmets of upto 150mm/200 mm x 150 to 300 mm L shape made of 19 mm thick ply & 4mm thk Veneer with Melamine Polish as per drawing. Rate to be inclusive of lipping, cutting, wastages, necessary fixtures, nails, adhesives, necessary scaffolding, fixing at all heights and for all floors as per drawing and approved sample etc should also take load of all the all roller blinds.

Providing and fixing of Pergo 8mm thick AC-4( average 4550 cycles) Domestic Extra series Laminate wooden flooring with Titan X Coating, impact resistance 9N, and resistance to cigarette burn with a rating of 4 (EN 438-2.05) material should be installed on Pergo combi foam and polythene,complete in all respects and the entire satisfaction of Architect and Engineer-in-charge.

Providing and fixing of pergo laminate Wooden Flooring Skirting and beeding patti as per manufacturer's specificatons with ,complete in all respects and the entire satisfaction of Architect and Engineer-in-charge.

Providing and fixing of factory manufactured Aluminium Skirting (kubix) consist 80mm x 0.8mm thk Fixed on partition Or wall surfaces with Easy fixing caping strip & alligator anchor . The work includes flush looking without joint seing complete in all respects and the entire satisfaction of Architect and Engineer-in-charge.

Providing and fixing removable raised/False access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panelssupported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the architectural drawings, as marine and as directed by Architect and Engineer-in-charge consisting of: (a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug. (b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid

Providing Suppllying and fixing of Bluestar 150L Water Cooler: The SDLX 15150 model is a 150 liter water cooler which has a cooling capacity of 150 liter and storage capacity of 150 liter. per hour @ an ambient temp of 45˚ C. The outlet temp. of the water should drop by 15˚ C within a hour, The water cooler should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating coil, thermostats, relay etc. complete with necessary inlet & outlet connection. The body of water cooler will be made from Stainless Steel.It has two faucets. Both of them give cold water. The dimensions of the water cooler are 33 inch width, 28 inch depth and 49 inch height.

Supplying & erecting Reverse osmosis (RO) water purification system with M.S. powder coated pedestal frame, prefilter housing carbon filter suitable buster DC pump, auto low & high pressure switches with following size of LPH capacity & erected as directed with one year comprehensive maintenance guarantee. [D] 100 LPH with 3 phase Raw water pump of 500LPH @ 2.5kg/cm2 - (1N0 - Kirloskar /CRI/Lubi), Dual media filter 10"x54" - (1 No), Micron cartridge filter 20" x 2.5" ( 1No), High pressure pump 500LPH @ 10kg/cm2 - (1No - Shimge /CRI /Lubi), RO Membrane housing with RO membrane of 40*40 - (1No), RO pressure tube 4" x 1E - ( 1No), 0 - 1200LPH Rotameter -(2 Nos), with Recovery Rate 50%.

Supplying & erecting SAMSUNG LED T.V. of 55 inch size.Resolution Full HD (1920x1080) with refresh rate 60 Hertz.2 HDMI ports to connect set top box, Blu-ray speakers or gaming console. 1 USB ports to connect hard drives or other USB devices.20 Watts output with Dolby Digital Plus 2CH Speaker Type.Tizen OS screen with In-Built WiFi,Screen Mirroring,1.5 GB RAM, 8 GB ROM, Supported Apps: Netflix, Prime Video, YouTube, Zee5, etc.Display : Hyper Real Picture Engine, 178 Degree Viewing Angle, Mega Contrast, Contrast Enhancer, PurColor, 1000 PQI.USB /HDMI supported.Audio Wattage 20 watts. Voltage 240 watts. Power source AC.Media format ‎AVI, MPEG . Item weight 6KG 400GM.Battery cell composition Lithium Ion.Speaker Surround Sound Channel Configuration ‎Dolby Digital Plus.

Supplying & erecting SAMSUNG LED T.V. of 75 inch size.Resolution Full HD (1920x1080) with refresh rate 60 Hertz.2 HDMI ports to connect set top box, Blu-ray speakers or gaming console. 1 USB ports to connect hard drives or other USB devices.20 Watts output with Dolby Digital Plus 2CH Speaker Type.Tizen OS screen with In-Built WiFi,Screen Mirroring,1.5 GB RAM, 8 GB ROM, Supported Apps: Netflix, Prime Video, YouTube, Zee5, etc.Display : Hyper Real Picture Engine, 178 Degree Viewing Angle, Mega Contrast, Contrast Enhancer, PurColor, 1000 PQI.USB /HDMI supported.Audio Wattage 20 watts. Voltage 240 watts. Power source AC.Media format ‎AVI, MPEG . Item weight 6KG 400GM.Battery cell composition Lithium Ion.Speaker Surround Sound Channel Configuration ‎Dolby Digital Plus.

Providing ,fixing & Erecting of 'V' Shape Conference Room Table (GF) Table Size -(12000+12000+2100 x 830mm width x 750ht.) Trapezoidal shape as per shown on the Drawing made out of 19 mm thick Marine Ply with 40 mm thk leading edges having 50mm x 38mm bull nosed leading edges polished to match table top Veneer with melamine / PU over coat. 50mm x 50mm Solid teak wood frame under carriage with 8mm thk ply with Veneer finished. Also Provide Partly Portion in Top 6mm Corien, Corien Cladding,Veneer Fluted Paneling , Teakwood Carving Edge Patti As per Drawing,Table base to have Top flap/cut out for electrical/data pop up switch boxes & shutters below to service the electric equipment as required. Complete as per detail drawing & directed by the Architect. Rate inclusive of polishing work of all exposed Surfaces as per Directed & 8 no.s of POP boxes of make Le grand / Equivalent. Annual maintenance included upto 3 years.

Providing ,fixing & Erecting of 'V' Shape Conference Room Table (FF) Size - (5200+5200+2100 x 830mm width x 750ht. ) Trapezoidal shape as per shown on the Drawing made out of 19 mm thick Marine Ply with 40 mm thk leading edges having 50mm x 38mm bull nosed leading edges polished to match table top Veneer with melamine / PU over coat. 50mm x 50mm Solid teak wood frame under carriage with 8mm thk ply with Veneer finished. Also Provide Partly Portion in Top 6mm Corien, Corien Cladding,Veneer Fluted Paneling , Teakwood Carving Edge Patti As per Drawing,Table base to have Top flap/cut out for electrical/data pop up switch boxes & shutters below to service the electric equipment as required. Complete as per detail drawing & directed by the Architect. Rate inclusive of polishing work of all exposed Surfaces as per Directed & 8 no.s of POP boxes of make Le grand / Equivalent. Annual maintenance included upto 3 years.

Providing ,Fixing & Erecting of Reception Table Veneer Finish (GF) (Size 3600mm x 850mm )Size and shape as per drawing. Table top Made from 25mm th.Marine plywood finished with 4mm th. approved veneer with 6mm thk Corien Top & 18 mm th.verticals side.finished with 4mm thk veneer ,corien Cladding, Veneer Fluted Paneling as per Drawing. Table shall have drawer of 100mm wide on top level with apron of 18mm th ply shall be finished with veneer higher level counter is to be provided 8mm thk.Corian Top held in position using 30mm S S pipe as per design including storage unit made using 19 mm ply. All exposed edges to be sealed with Carving Edge, 4mm veneer , Corien Cladding, Fluted Panel Cladding etc & all exposed work veneer finished with Melamine or PU polish Complete as per the drawing and design or as directed by Engineer-in-Charge/Designer.Annual maintenance included upto 3 years.

Providing ,Fixing & Erecting of Reception Table (FF Adm) size 2100mm x 675mm and shape as per drawing. Table top Made from 25mm th.Marine plywood finished with 4mm th. approved veneer & 18 mm th.verticals side.finished with veneer & Table shall have drawer of 100mm wide on top level with apron of 18mm th ply shall be finished with veneer higher level counter is to be provided 8mm thk.CorianTop held in position using 30mm S S pipe as per design including storage unit made using 19 mm ply.All exposed edges to be sealed with Carving Edge, 4mm veneer , Corien Cladding, Fluted Panel Cladding etc & all exposed work veneer finished with Melamine or PU polish Complete as per the drawing and design or as directed by Engineer-in-Charge/Designer.Annual maintenance included upto 3 years.

Providing ,fixing & Erecting of Administative table 3000mm x 1200mm size and shape as per drawing. Table top Made 50mm thick from marine Ply & teakwood edge, carving patti with polishing & Finished with 4 mm th Approved Veneer with PU Polish work/ Partly Corien top as per drawing. table also Provide Drawer box made from 18mm thick Ply with Veneer as sides on 6mm th ply as backing. Table shall have drawer of 100mm wide on top level & back side and bottom to be provided with 12mm th. prelame ply Drawer to be lockable and sliding on aluminum drawer channels Drawer box size (450mm X 450mm X 300mm) consisting of 100mm wide 2 Nos. of drawer.(As per drawing) drawer box fixed with SS pipe as per drawing & All exposed wooden edges to be sealed with Veneer with Polish / Carving Patty, Partly Corien Cladding, Fluted Paneling etc as per Directed with all necessary hardware like drawer handle, locks CPU Trolly/key board tray /one cable manager etc.Complete as per Drawing .Annual maintenance included upto 3 years.

Providing ,fixing & Erecting of Side Cabinet (Administative table) size and shape as per drawing.(1200mm Lx450Dx710H) Cabinet top Made 50mm thick from marine Ply & teakwood edge, carving patti with polishing & Finished with 4 mm th Approved Veneer with marine Polish work/ Corien top as per drawing. Cabinet also Provide Drawer box made from 18mm thick Ply with Veneer, Cabinet shall have drawer of 100mm wide on top level & Sliding shutter (As per drawing) All exposed wooden edges to be sealed with Veneer with Polish as per Directed with all necessary hardware like drawer handle, locks etc.Complete as per Drawing .Annual maintenance included upto 3 years.

Providing ,fixing & Erecting of Full Height Storage Cabinet Veneer Finish (Back Credenza) 425mm Deep as per Drawing) storage cabinet top 50mm thk made from 18mm th. marine ply wood finished with 4mm th Approved Veneer from outside & Top With all exposed Surfaces veneer with PU or melamine polish. in side storage made from 19mm Pre lame ply & Shutter operated on auto closing hinges, 19mm th prelam ply to be providing for self having vertical 100mm wide18mm th band for supporting files. Storage will have individual locking arrangement ,necessary Teak wood beading patti Carving edge with Melamine or PU polish, & necessary hardware like SS mat finish handles/ ball catch. Complete as shown in the drg. & Design or as directed by Engineer-in Charge.Annual maintenance included upto 3 years.

Providing, Supplying and Fixing of 3 Seater Sofa (NT room) Factory made as per below specification including Erection at site. 3 Seater : Size : 2125L X 900D X 675H Frame : The sofa's frame is made from Marine ply and Hard wood Uphoilstery : Leatherette upholstered back and seat Colour : Black Legs : Mild Steel (Black)Modules : 3 Seater Polyurethane foam with 40 kg per cubic meter density for seats and 28kg per cubic meter for arms and back.

Providing, Supplying and Fixing of Rectangular Center Table (NT room) Factory made as per Directed By Engineer In Charge , including Erection at site. Size : 1200L x 600D x 450H

Providing, Supplying and Fixing of Circular Side Table (NT room) Factory made as per Directed By Engineer In Charge Erection at site. SIZE: 600x600 x 450H

Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. Pedestal : 2 Drawers & 1 Filling Drawer pedestal with castors - finish in 18 MM thk. Prelaminated Particle Board 2MM PVC Edge band to all Exposed Area & Metal Drawer with Centralized Lock with side finger grove.

Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. CUBE Cabin Table with Side Credenza (For Dy. Secretory (2400x900x750mm) TABLE TOP : 50mm thick baton structure. Baton frame is made up 25mm thick Prelaminated PB finish. UNDERSTRUCTURE : Gable end is Made up of it is baton structure is which is made up 25mm thick Prelaminated PB finish. STORAGE : LH / RH side is made in baton structure is which is made up 25mm thick Prelaminated PB finish. (SIDE CREDENZA: 1850 x 600 x 625)

Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. Z LINE Cabin Table With Side Credenza Membrane Finish (For Secretory 2530x2100x750) Director's Suite :- TOP made up of 18mm MDF Membrane top with additional 18mm thickness all over the edge with Decorative Aluminium Anodized Profile all over and soft water fall edges GABLE END in 67mm THK box type shape to be made of MDF Membrane + Partical finish Decorated Anodised section at front and back side MODESTY PANEL to be made of 18 mm thick Prelaminated particle board with PVC edge band INCLUDING LOW HEIGHT CREDESTAL @ 1200Lx450Dx 650HT :- To be made out of MDF with Membrane finish consist of three Drawers and 2 openable shutters. Top and side panel joined in 45 deg construction with soft water fall edges on all the front side. Complete body in 18mm thickness and drawers in 18mm thickness.

Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. Lift Foyer Table With Pedestal (1500W x 600D x 750H) TABLE TOP : 25 MM thk. Prelaminated Particle Board with 2MM PVC Edge band on all side. Table top at 750MM height from floor level. Cut-out provision for Access flap as required. UNDERSTRUCTURE : HOCK LEG : Designer MS Tapered Leg made up of 50x75MM verticals and Horizontal Connecting member made up of 40x40MM MS pipe finished in Powder coating. Cross members made up of 40x40MM MS Section finished in Powder coating are connected to Legs with Brackets for table support. WIRE MANAGMENT : Powder coated Switch mounting box below table top. Provision of vertical duct to take out cable from floor to box. MODESTY 450 MM HT.: Metal perforated moesty. ACCESS FLAP 450MM LENGTH : Special Aluminium access flap . 2 Drawers & 1 Filling Drawer pedestal with castors - finish in 18 MM thk. Prelaminated Particle Board 2MM PVC Edge band to all Exposed Area & Metal Drawer with Centralized Lock with side finger grove. MODESTY 450 MM HT.: Metal perforated moesty.

Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. Cabin Table With Side Credenza (1200W x450D X 750D (2100x900x750) TABLE TOP : 25 MM thk. Prelaminated Particle Board with 2MM PVC Edge band on all side. Table top at 750MM height from floor level. Cut-out provision for Access flap as required. UNDERSTRUCTURE : HOCK LEG : Designer MS Tapered Leg made up of 50x75MM verticals and Horizontal Connecting member made up of 40x40MM MS pipe finished in Powder coating. Cross members made up of 40x40MM MS Section finished in Powder coating are connected to Legs with Brackets for table support. WIRE MANAGMENT : Powder coated Switch mounting box below table top. Provision of vertical duct to take out cable from floor to box. ACCESS FLAP 450MM LENGTH : Special Aluminium access flap . SIDE CREDENZA : 2 Drawers & 1 Filling Drawer With Openable Shutter finish in 25 / 18 MM thk. Prelaminated PB Board 2MM PVC Edge band to all Exposed Area & Metal Drawer with Centralized Lock.

Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. Meeting Table 5 Seater (1800 x1100 x 750mm ) TABLE TOP : 25 MM thk. Prelaminated Particle Board with 2MM PVC Edge band on all side. Table top at 750MM height from floor level. Cut-out provision for Access flap as required. UNDERSTRUCTURE :HOCK LEG : Designer MS Tapered Leg made up of 50x75MM verticals and Horizontal Connecting member made up of 40x40MM MS pipe finished in Powder coating. Cross members made up of 40x40MM MS Section finished in Powder coating are connected to Legs with Brackets for table support. WIRE MANAGMENT : Special Aluminium flap with switch mounting box below table top and vertical duct for cable riser.

Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. Meeting Table 9/10 Seater (2400 x 1200 x 750mm ) TABLE TOP : 25 MM thk. Prelaminated Particle Board with 2MM PVC Edge band on all side. Table top at 750MM height from floor level. Cut-out provision for Access flap as required. UNDERSTRUCTURE :HOCK LEG : Designer MS Tapered Leg made up of 50x75MM verticals and Horizontal Connecting member made up of 40x40MM MS pipe finished in Powder coating. Cross members made up of 40x40MM MS Section finished in Powder coating are connected to Legs with Brackets for table support. WIRE MANAGMENT : Special Aluminium flap with switch mounting box below table top and vertical duct for cable riser.

Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. Cafe Table (900mm Dia x 750mm) TABLE TOP : 25 MM thk. Prelaminated Particle Board with 2MM PVC Edge band on all side. Table top at 750 MM height from floor level. UNDERSTRUCTURE : MS Powdercoated understructure.

Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. High Cafe Table (1800 x 800 x 1050mm ) TABLE TOP : 25 MM thk. Prelaminated Particle Board with 2MM PVC Edge band on all side. Table top at 1050 750 MM height from floor level. UNDERSTRUCTURE : Splayed ( Slant ) Legs made up of 40x40MM MS pipe finished in Powder coating. Cross members made up of 40x40MM MS Section finished in Powder coating are connected to Legs with Brackets for table support.

Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site.Midd Height Storage (1500 x 450 1050 ) TOP: 18MM Thick Prelaminated Partical Board with 2MM PVC edge band on all edges. CARCASS (Body/ Shutter / Back) : 18MM thick Prelaminated Partical Board with PVC edge band on all exposed edges. SHELF : One adjustable and One fixed shelf made of 18MM thick Prelaminated Partical Board with PVC edge band on all edges. SHUTTERS : Lockable Swing shutters with Finger Groove. HARDWARE : Hettich Hinges, Lock

Providing ,Supplying and fixing of Factory made Chair as per below specification including erection at site Medium Back Chair ( ELAN MB) Work station Chair , Cabin Visitor– Specification ,Backrest : Mid back,Upholstery : Backrest : Mesh (Black), Seat : Fabric (Black, Grey, Red, Blue), Armrest : 1D PP Armrest,Mechanism : 1P Synchro, Gaslift : Class 4, 100mm Stroke, Base : Nylon Dia 660mm, Castor : Nylon, Dia 60mm,Lumber : Yes

Providing ,Supplying and fixing of Factory made Chair as per below specification including erection at site. Meeting / Conference Room Chair (Light Up ) – Specification , Backrest : High Mid back, Upholstery : Backrest : Mesh (Black), Seat : Fabric (Black, Grey, Red, Blue), Armrest : 1D PP Armrest, Mechanism : Synchro 1P, Gaslift : Class 4, 112mm Stroke, Base : Nylon Dia 660mm, Castor : Nylon, Dia 60mm,Lumber : Yes

Providing ,Supplying and fixing of Factory made Chair as per below specification including erection at site. Cabin Table Chair (ONYX HIGH BACK ) Chair Back : Mesh Back with adjustable Head Rest ( Up , Down & swivel ), Chair Seat : Contoured seat design upholstered with breathable fabric, Lumber Support : adjustable lumbar support, Armrest : 1D PU Armrest , Arm pads can be moved up–down, Mechanism : Synchro- 1P locking ( Seat and Back Synchronised Mechanism with 1 point back angle Locking positions), Gaslift : Class 4, 112mm Stroke for seat height adjustment, Base : Injection moulded 5 Prong Nylon base, 660mm diameter nylon, Castor : Nylon, Dia 60mm

Providing ,Supplying and fixing of Factory made Chair as per below specification including erection at site. Cafe Chair (GALA) Backrest : Injection Moulded Polypropylene, Seat : Injection Moulded Polypropylene, Colour : Blue / Yellow / Grey / White, Under structure : MS Rod, Finish : Powder coat (Silver grey), Foot pad : Nylon glide

Providing ,Supplying and fixing of Factory made Sofa as per below specification including erection at site. 1 Seater Sofa (TURF 1 Seater FABRIC -MSLEG- Dy.Secretory Room Sofa) , Frame : The sofa’s frame is made from solid, sustainable wood and commercial ply, Upholstery: The seat and back are upholstered in Fabric / Leatherette, Legs: Powder coating (black)

Providing ,Supplying and fixing of Factory made Sofa as per below specification including erection at site. 2 Seater Sofa (TURF 2 Seater FABRIC -MSLEG- Dy.Secretory Room Sofa) ,Frame : The sofa’s frame is made from solid, sustainable wood and commercial ply, Upholstery: The seat and back are upholstered in Fabric / Leatherette, Legs: Powder coating (black)

Providing ,Supplying and fixing of Factory made Sofa as per below specification including erection at site. 1 Seater Sofa (EASE 1 Seater FABRIC -SS LEG- Open Visitor Area) EASE - Specifications : Frame : The sofa’s frame is made from solid, sustainable wood and commercial ply,Upholstery: Fabric / Leatherette upholstered back and seat, Base-frame: 40x22x1.6mm thk SS pipe, Base frame finish: SS (mirror finish),

Providing ,Supplying and fixing of Factory made Sofa as per below specification including erection at site. 2 Seater Sofa (EASE 2 Seater FABRIC -SS LEG- Open Visitor Area) EASE - Specifications: Frame : The sofa’s frame is made from solid, sustainable wood and commercial ply,Upholstery: Fabric / Leatherette upholstered back and seat, Base-frame: 40x22x1.6mm thk SS pipe, Base frame finish: SS (mirror finish),

Providing ,Supplying and fixing of Factory made Sofa as per below specification including erection at site. 3 Seater Sofa (EASE 3 Seater FABRIC -SS LEG- Open Visitor Area) EASE - Specifications : Frame : The sofa’s frame is made from solid, sustainable wood and commercial ply, Upholstery: Fabric / Leatherette upholstered back and seat, Base-frame: 40x22x1.6mm thk SS pipe, Base frame finish: SS (mirror finish),

Providing ,Supplying and fixing of Factory made Chair as per below specification including erection at site. POLO - High Café chair HIGH Cafeteria Chair with Metal legs

Providing ,Supplying and fixing of Factory made Center Table as per below specification including erection at site. BUDDY CENTER TABLE@ 900 x 600 x 450 mm HT. TOP 25mm Thk. Prelame PB with Rev Chamf Edge MSPC Base

Providing ,Supplying and fixing of Factory made Side Table as per below specification including erection at site.BUDDY SIDE TABLE@ 600 x 600 x 450 mm HT. - For Open Area : Top 25mm Thk Prelamm PB With Rev Chamf Edge MSPC Base

Providing ,Supplying and fixing of Factory made Chair as per below specification including erection at site.High Back Chair (Board Room Chair) High Back Chair ,Seat & Back Leather ( Body Touch ), Multilock with Knee tilt Mechanism,Aluminum Fixed Arms, Aluminum Base with 60mm castors.,Colour : Black, Grey & Tan.

Providing ,Supplying and fixing of Factory made Chair as per below specification including erection at site.Medium Back Chair (Board Room Visitor Chair) Medium Back Chair, Seat & Back Leather , Multilock with Knee tilt Mechanism, Aluminum Fixed Arms , Aluminum Base with 60mm castors., Colour : Black, Grey & Tan.

Providing ,Supplying and fixing of Factory made Compactor Storge as per below specification including erection at site. Type : Double face Mechanical Unit ,Size : 1810 L X 900 D X 2130 H , Each Component of the System will be treated with rust preventive treatment and will be powder coated for better finish, Each Mobile Unit will have Mechanical arrangement, Total No. of Shelf levels per face as per drawing elevation , Annual maintenance included upto 3 years.

Providing ,Supplying and fixing of Factory made Compactor Storge as per below specification including erection at site.Type : Single face Fixed Unit, Size : 1810 L X 450 D X 2130 H, Each Component of the System will be treated with rust preventive treatment and will be powder coated for better finish, Each Mobile Unit will have Mechanical arrangement, Total No. of Shelf levels per face as per drawing elevation ,Annual maintenance included upto 3 years.

Providing ,Supplying and fixing of Factory made Compactor Storge as per below specification including erection at site. Type : Single face Mechanical Unit Size : 1810 L X 450 D X 2130 H ,Each Component of the System will be treated with rust preventive treatment and will be powder coated for better finish ,Each Mobile Unit will have Mechanical arrangement,Total No. of Shelf levels per face as per drawing elevation Annual maintenance included upto 3 years.