LED Luminaire (for Flood Light) ( PAC Only )
LED Luminaire (For Road and Street Lights) ( PAC Only )
LED Luminaire (Recessed Luminaire) ( PAC Only )
LED Luminaire (Recessed Luminaire) ( PAC Only ) LED Luminaire (for Flood Light) ( 20 ) ( Under PAC ) Make shreeg Model glitz300 Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 5/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes * Photo biological safety of LEDs used shall be as per IS:16108/2012 Yes * 1/55 (exempt group) Types of LED Luminaire as per the IS: 16107(Part-2 Sec.-1)/2012 Type B * Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 * LED Rating/System Wattage/Rated Power 300W * Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt * Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP65 IP66
IP65
IP67 Mounting brackets (included) Adjustable * Warranty for free replacement (in Years) 2 * ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 90 to 300 V olts AC at 50 Hz+/-2 Hz * Automatic Higher Cut off voltage above 300 volt Yes * Rated voltage 230 V AC 50 Hz * AC Power Factor at full load ≥ 0.95 * Driver Efficiency (in %age) ≥85 * Total Harmonics Distortion (in %age) ≤ 10 * "The total circuit power shall not be more than 110 percent of the value declared by the manufacturer" Yes * OPTICAL LED chip Efficacy ≥130 Lm/Watt * Colour temperature (+/-500K) 6000K * Working life for LED (Minimum 50
000 burning hours as per LM-80 report) Yes * Colour Rendering Index(CRI) ≥70 * 2/55 Beam Angle ≥120 * Optic lense materal (UV stabilised) (Write NA for without optic lense supply) NA * THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes * Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes * Junction temperature < 85 degC * Operating temperature range -10 deg C to +55 deg C * Operating Humidity Range 10 % to 95% RH * PROTECTION Short circuit Protection Yes * Over load protecton Yes * Over Voltage protection Yes * Reverse polarity Yes * High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes * Insulation resistance between earth and current carrying part >100 M ohm * The luminaire shall be protected against surges and transients ( Internal) >/=4KV * The luminaire shall be protected against surges and transients of >/=10KV (External) No * CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes * The luminaire body must be corrosion resistant epoxy powder Yes * 3/55 coated All fastners must be of stainless steel Yes * The entire housing (both LED section and driver section) shall be dust and water proof having IP 66 protection as per IS:10322 (Part 1):1982 latest Yes * Extruded silicon loop gasket shall be provided in the lantern body to ensure a weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust
water
insects etc.
Yes * Luminaries light transparency should be of Toughened glass Yes * Toughned transparent glass cover thickness >/=4 mm * Toughned Glass shall not get discoloured shall not suffer degration due to heat and ageing within warranty period Yes * Number of electronic control gear (power supplies) 1 No. 1 No.
2 Nos.
3 Nos.
4 Nos. Driver components shall be industrial grade or above Yes * PCB shall be FR4 grade minimum 0.8 to 1.0 mm thick or more Yes * The Luminaires works on single phase three wires system (Phase
Neutral and Earth) Yes * Suitable connector shall be provided for LED connection between driver output and LED Yes * Length of ISI marked three core wire (shall 50 cm * 4/55 be provided along with supply of material) Light Source SMD LED Chip as per LM 80/IS16106 * MARKING "Manufactures Name and and brand on the aluminium die cast body Engraved/Embossed * Manufacturer’s name
model number
serial number Yes * Date of manufacture (month-year)
and lot number as identification mark inside each unit and the outside of each packaging box Yes * The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes * REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILED/PHILIPS EDISON/SYSKA LUMENMAX EVERLIGHT BRIDGELUX NATIONSTAR/REFOND * System must have EMI/EMC compliance as applicable (Test reports shall be furnish on demand by buyer/consignee) Yes * LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government lab/NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-79 report shall have total lumen output
power
PF
Current in Amps
CRI & CCT etc.
) Yes * LM 80 & TM 21 (Part of LM 80) (Ref. IS:16105:2012) Reports Yes * 5/55 and Photo biological report for LED report from Central Government lab NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-80 report shall haveand the Pohoto Biological report of the LED Chip being used in the luminaire) Availability of test Report from Central Government lab/NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-5/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes * Seller has to furnish Type test report on demand by buyer/consignee Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * LED Luminaire for Flood Light shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 5): 2012 as applicable on the date Yes * * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001
O/o Executive Engineer
(E&M) Public Works Department Sirpur Bhawan Parisar
Raipur. (C.G.) 20 15 LED Luminaire (for Flood Light) ( 13 ) ( Under PAC ) 6/55 Make shreeg Model glitz200w Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 5/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes * Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes * Types of LED Luminaire as per the IS: 16107(Part-2 Sec.-1)/2012 Type B * Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 * LED Rating/System Wattage/Rated Power 200W * Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt * Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP65 IP66
IP67 Mounting brackets (included) Adjustable * Warranty for free replacement (in Years) 2 * ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 90 to 300 V olts AC at 50 Hz+/-2 Hz * Automatic Higher Cut off voltage above 300 volt Yes * Rated voltage 230 V AC 50 Hz * AC Power Factor at full load ≥ 0.95 * Driver Efficiency (in %age) ≥85 * 7/55 Total Harmonics Distortion (in %age) ≤ 10 * "The total circuit power shall not be more than 110 percent of the value declared by the manufacturer" Yes * OPTICAL LED chip Efficacy ≥130 Lm/Watt * Colour temperature (+/-500K) 6000K * Working life for LED (Minimum 50
000 burning hours as per LM-80 report) Yes * Colour Rendering Index(CRI) ≥70 * Beam Angle ≥120 * Optic lense materal (UV stabilised) (Write NA for without optic lense supply) NA * THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes * Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes * Junction temperature < 85 degC * Operating temperature range -10 deg C to +50 deg C * Operating Humidity Range 10 % to 95% RH * PROTECTION Short circuit Protection Yes * Over load protecton Yes * Over Voltage protection Yes * Reverse polarity Yes * High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes * Insulation resistance between earth and current carrying part >100 M ohm * 8/55 The luminaire shall be protected against surges and transients ( Internal) >/=4KV * The luminaire shall be protected against surges and transients of >/=10KV (External) No * CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes * The luminaire body must be corrosion resistant epoxy powder coated Yes * All fastners must be of stainless steel Yes * The entire housing (both LED section and driver section) shall be dust and water proof having IP 66 protection as per IS:10322 (Part 1):1982 latest Yes * Extruded silicon loop gasket shall be provided in the lantern body to ensure a weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust
4 Nos. 9/55 Driver components shall be industrial grade or above Yes * PCB shall be FR4 grade minimum 0.8 to 1.0 mm thick or more Yes * The Luminaires works on single phase three wires system (Phase
Neutral and Earth) Yes * Suitable connector shall be provided for LED connection between driver output and LED Yes * Length of ISI marked three core wire (shall be provided along with supply of material) 50 cm * Light Source SMD LED Chip as per LM 80/IS16106 * MARKING "Manufactures Name and and brand on the aluminium die cast body Engraved/Embossed * Manufacturer’s name
and lot number as identification mark inside each unit and the outside of each packaging box Yes * The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes * REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILED/PHILIPS EDISON/SYSKA LUMENMAX EVERLIGHT BRIDGELUX NATIONSTAR/REFOND * System must have EMI/EMC compliance as applicable (Test reports Yes * 10/55 shall be furnish on demand by buyer/consignee) LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government lab/NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-79 report shall have total lumen output
) Yes * LM 80 & TM 21 (Part of LM 80) (Ref. IS:16105:2012) Reports and Photo biological report for LED report from Central Government lab NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-80 report shall haveand the Pohoto Biological report of the LED Chip being used in the luminaire) Yes * Availability of test Report from Central Government lab/NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-5/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes * Seller has to furnish Type test report on demand by buyer/consignee Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * LED Luminaire for Flood Light shall comply with Complusory Registration(CRS) of Yes * 11/55 BIS for safety as per IS 10322 (Part 5/Section 5): 2012 as applicable on the date * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001
Raipur. (C.G.) 13 15 LED Luminaire (for Flood Light) ( 12 ) ( Under PAC ) Make shreeg Model glitz50w Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 5/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes * Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes * Types of LED Luminaire as per the IS: 16107(Part-2 Sec.-1)/2012 Type B * Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 * LED Rating/System Wattage/Rated Power 50W * Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt * Ingress Protection IP65 IP66
IP67 12/55 (IP Rating) as per IS:10322 (Part 1):1982 latest Mounting brackets (included) Adjustable * Warranty for free replacement (in Years) 2 * ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 90 to 300 V olts AC at 50 Hz+/-2 Hz * Automatic Higher Cut off voltage above 300 volt Yes * Rated voltage 230 V AC 50 Hz * AC Power Factor at full load ≥ 0.95 * Driver Efficiency (in %age) ≥85 * Total Harmonics Distortion (in %age) ≤ 10 * "The total circuit power shall not be more than 110 percent of the value declared by the manufacturer" Yes * OPTICAL LED chip Efficacy ≥130 Lm/Watt * Colour temperature (+/-500K) 6000K * Working life for LED (Minimum 50
000 burning hours as per LM-80 report) Yes * Colour Rendering Index(CRI) ≥70 * Beam Angle ≥120 * Optic lense materal (UV stabilised) (Write NA for without optic lense supply) NA * THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes * Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes * Junction temperature < 85 degC * 13/55 Operating temperature range -10 deg C to +50 deg C * Operating Humidity Range 10 % to 95% RH * PROTECTION Short circuit Protection Yes * Over load protecton Yes * Over Voltage protection Yes * Reverse polarity Yes * High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes * Insulation resistance between earth and current carrying part >100 M ohm * The luminaire shall be protected against surges and transients ( Internal) >/=4KV * The luminaire shall be protected against surges and transients of >/=10KV (External) No * CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes * The luminaire body must be corrosion resistant epoxy powder coated Yes * All fastners must be of stainless steel Yes * The entire housing (both LED section and driver section) shall be dust and water proof having IP 66 protection as per IS:10322 (Part 1):1982 latest Yes * Extruded silicon loop gasket shall be provided in the lantern body to ensure a weather proof seal between the UV Glass Yes * 14/55 cover and the metal housing to exclude the entry of the dust
Luminaries light transparency should be of Toughened glass Yes * Toughned transparent glass cover thickness >/=4 mm * Toughned Glass shall not get discoloured shall not suffer degration due to heat and ageing within warranty period Yes * Number of electronic control gear (power supplies) 1 No. 1 No.
and lot number as identification mark Yes * 15/55 inside each unit and the outside of each packaging box The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes * REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILED/PHILIPS EDISON/SYSKA LUMENMAX EVERLIGHT BRIDGELUX NATIONSTAR/REFOND * System must have EMI/EMC compliance as applicable (Test reports shall be furnish on demand by buyer/consignee) Yes * LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government lab/NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-79 report shall have total lumen output
) Yes * LM 80 & TM 21 (Part of LM 80) (Ref. IS:16105:2012) Reports and Photo biological report for LED report from Central Government lab NABL/ILAC accrediated lab. Reports shall be furnish on demany by buyer (LM-80 report shall haveand the Pohoto Biological report of the LED Chip being used in the luminaire) Yes * Availability of test Report from Central Government lab/NABL/ILAC Yes * 16/55 accrediated lab to Indian Standrad IS:10322/part 5/sec-5/2012 and IS 16107 (Part 2/Sec 1) : 2012 Seller has to furnish Type test report on demand by buyer/consignee Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * LED Luminaire for Flood Light shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 5): 2012 as applicable on the date Yes * * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001
Raipur. (C.G.) 12 15 LED Luminaire (For Road And Street Lights) ( 10 ) ( Under PAC ) Make shreeg Model glance120w Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 3/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes * 17/55 Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes * Types of LED Luminaire as per the IS: 16107(Part-2 Sec.-1)/2012 Type B * Types of LED Modules as per the IS:IS: 16103(Part-2)/2012 Type 3 * LED Rating (in Watts)/System Wattage/Rated Power 120W * Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt * Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP66 * Warranty for free replacement (in years) 2 2
3
4
5 ELECTRICAL EFFICIENCY Input operating Voltage range and frequency 90 to 300 Volts AC at 50 Hz+/-2 * Automatic Higher Cut off voltage above 300 volt Yes * Rated voltage 230 V AC 50 Hz * AC Power Factor at full load ≥ 0.95 * Driver Efficiency (in %age) Upto 100W: ≥85%
Above 100W: >/=90% Yes * Total Harmonics Distortion ≤ 10 * "The total circuit power shall not be more than 110 percent of the value declared by the manufacturer (as per Cl. 8 of IS:16104:2012 lates)" Yes * OPTICAL LED chip Efficacy ≥130 Lm/Watt * Colour temperature 6000+/-500K * Working life for LED (Minimum 50
000 burning hours as per Yes * 18/55 LM-80 and LM 21 reports) Colour Rendering Index(CRI) ≥70 * LED Beam Angle ≥120 * Optic lense materal (UV stabilised) Poly carbonate lense * THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes * Junctiojn/Soldering point temperature shall not exceed 85 deg.c as per LM 80 report Yes * Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes * Operating temperature range -10 deg C to +55 deg C -20 deg. C to +50 deg. C
10 deg C to +50 deg C
10 deg C to +55 deg C Operating Humidity Range 10 % to 95% RH * PROTECTION Short circuit Protection Yes * Over load protecton Yes * Over Voltage protection Yes * Reverse polarity Yes * High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes * Insulation resistance between earth and current carrying part >100 M Ohm * The luminaire shall be protected against surges and transients ( Internal) >/=4KV * The luminaire shall be protected against surges and transients of >/=10KV (External) No * CONSTRUCTIONAL The Luminaires casing/housing (single Yes * 19/55 piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity The luminaire body must be corrosion resistant powder coated Yes * All fastners must be of stainless steel Yes * Protection of the entire housing (both LED section and driver section) as per IS:10322 (Part 1):1982 latest IP66 * Extruded silicon loop gasket shall be provided in the lantern body to ensure a weather proof seal between the UV Glass cover and the metal housing to exclude the entry of the dust
4 Nos. Light Source SMD LED Chip as per LM 80/IS16106 * Driver components shall be industrial grade or above Yes * PCB shall be FR4 grade minimum 0.8 to 1.0 mm thick or more Yes * The Luminaires works on single phase three Yes * 20/55 wires system (Phase
Neutral and Earth) Suitable connector shall be provided for LED connection between driver output and LED Yes * Length of ISI marked three core wire (shall be provided along with supply of material) 50 cm 50 cm
100 cm MARKING "Manufactures Name and and brand on the aluminium die cast body " Engraved/Embossed * Manufacturer’s name
and lot number as identification mark inside each unit and the outside of each packaging box Yes * The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes * Diameter of pole Luminiare suitable for: (upto 45W Pole OD: shall be 40mm)
(>45W<120W Pole OD: Shall be 50 mm)
(above 120W: OD shall be 60 mm for which luminiare is suitable Yes * REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILEDS/PHILIPS SYSKA/LUMENMAX EVERLIGHT/EDISON BRIDGELUX NATIONSTAR/REFOND * System must have EMI/EMC compliance as applicable (Test reports shall be furnish to the buyer/consignee on demand) Yes * 21/55 LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer consignee on demand (LM-79 report shall have total lumen output
) Yes * LM 80 & TM 21 (Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer consignee on demand (LM-80 report shall have the Pohoto Biological report of the LED Chip being used in the luminaire) Yes * Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-3/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes * Seller shall furnish the Type test reports to the buyer/consignee on demand Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * LED Luminaire for road and street lighting shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 3): 2012 as applicable Yes * 22/55 on date * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001
Raipur. (C.G.) 10 15 LED Luminaire (For Road And Street Lights) ( 6 ) ( Under PAC ) Make shreeg Model glance70w Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values STANDARDS LED Luminaire conformity to IS:10322/Part 5/Section 3/2012 latest and IS: 16107 (Part 2/Sec 1):2012 latest Yes * Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes * Types of LED Luminaire as per the IS: 16107(Part-2 Sec.-1)/2012 Type B * Types of LED Modules as per the IS:IS: 16103(Part-2)/2012 Type 3 * LED Rating (in Watts)/System Wattage/Rated Power 70W * Luminaire System Efficacy (Lumen/watt) >/= 100 Lm/Watt * Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest IP66 * 23/55 Warranty for free replacement (in years) 2 2
000 burning hours as per LM-80 and LM 21 reports) Yes * Colour Rendering Index(CRI) ≥70 * LED Beam Angle ≥120 * Optic lense materal (UV stabilised) Poly carbonate lense * THERMAL MANAGEMENT Heat sink should be die- cast aluminium along with sufficient heat sink fins to dissipate heat effectively Yes * Junctiojn/Soldering point temperature shall not exceed 85 deg.c as per LM 80 report Yes * Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes * 24/55 Operating temperature range -10 deg C to +55 deg C -20 deg. C to +50 deg. C
10 deg C to +55 deg C Operating Humidity Range 10 % to 95% RH * PROTECTION Short circuit Protection Yes * Over load protecton Yes * Over Voltage protection Yes * Reverse polarity Yes * High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes * Insulation resistance between earth and current carrying part >100 M Ohm * The luminaire shall be protected against surges and transients ( Internal) >/=4KV * The luminaire shall be protected against surges and transients of >/=10KV (External) No * CONSTRUCTIONAL The Luminaires casing/housing (single piece housing) shall be pressure die casted aluminium alloy with higher thermal conductivity Yes * The luminaire body must be corrosion resistant powder coated Yes * All fastners must be of stainless steel Yes * Protection of the entire housing (both LED section and driver section) as per IS:10322 (Part 1):1982 latest IP66 * Extruded silicon loop gasket shall be provided in the lantern body to ensure a weather proof seal Yes * 25/55 between the UV Glass cover and the metal housing to exclude the entry of the dust
4 Nos. Light Source SMD LED Chip as per LM 80/IS16106 * Driver components shall be industrial grade or above Yes * PCB shall be FR4 grade minimum 0.8 to 1.0 mm thick or more Yes * The Luminaires works on single phase three wires system (Phase
Neutral and Earth) Yes * Suitable connector shall be provided for LED connection between driver output and LED Yes * Length of ISI marked three core wire (shall be provided along with supply of material) 50 cm 50 cm
and lot Yes * 26/55 number as identification mark inside each unit and the outside of each packaging box The operation characteristics voltage and power be marked inside of each LED luminaire unit Yes * Diameter of pole Luminiare suitable for: (upto 45W Pole OD: shall be 40mm)
(above 120W: OD shall be 60 mm for which luminiare is suitable Yes * REPORTS AND CERTIFICATIONS LED Make OSRAM/NICHIA/CREE SAMSUNG/SEOUL LUMILEDS/PHILIPS SYSKA/LUMENMAX EVERLIGHT/EDISON BRIDGELUX NATIONSTAR/REFOND * System must have EMI/EMC compliance as applicable (Test reports shall be furnish to the buyer/consignee on demand) Yes * LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer consignee on demand (LM-79 report shall have total lumen output
) Yes * LM 80 & TM 21 (Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer Yes * 27/55 consignee on demand (LM-80 report shall have the Pohoto Biological report of the LED Chip being used in the luminaire) Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-3/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes * Seller shall furnish the Type test reports to the buyer/consignee on demand Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * LED Luminaire for road and street lighting shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 3): 2012 as applicable on date Yes * * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001
Raipur. (C.G.) 6 15 LED Luminaire (Recessed Luminaire) ( 65 ) ( Under PAC ) Make shreeg Model glim6 Technical Specifications 28/55 * As per GeM Category Specification Specification Specification Name Values Allowed Values STANDARDS Conformity to Indian Standard IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 for Recess type * Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * Luminaire Class (as per Cl. 2.1 Section 2 of IS: 10322 (Part-1) Class I * Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 * Rating of Recess type LED Luminaire/System Wattage/Rated Power 6W * Light Intensity(System Lumens) 80 Lm/Watt for 3000 deg K
90 Lm/Watt for 4000 deg K
100 Lm/Watt for 6000 deg K Yes * Color temeprature (+/- 500 K) 6000 deg K * Type of fixture (in feet) 1x1 (for 3W to 16W) 1x1 (for 3W to 16W)
1x2 (3W to 16W)
1x1 (for 18W to 28W)
1x2 (18W to 28W)
1x4 (30W to 48W)
2x2(30W to 48W) CONSTRUCTIONAL Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest (Minimum) IP20 * Mounting type Recess type * Diffuser material Acrylic * The luminaire body must be corrosion resistant epoxy powder Yes * 29/55 coated/anadozing All fastners must be of nickel/chrome plated Yes * Number of electronic control gear (power supplies) 1 * Light Source SMD LED Chip as per LM 80/IS16106 * Warranty for free replacement 2 Years * ELECTRICAL EFFICIENCY MANAGEMENT Operating Voltage and frequency range 140V to 280 V at 50 Hz AC * Rated voltage 230 V AC 50 Hz * AC Power Factor ≥ 0.90 * Driver Efficiency ≥85 * Total Harmonics Distortion ( ≤ 20% (for upto 20W) (</=10% (for above 20W) Yes * The total circuit power shall not be more than 110 percent of the value declared by the manufacturer (as per Cl 8 of IS:16104:2012 lates) Yes * OPTICAL MANAGEMENT LED chip Efficacy (≥130 Lm/Watt for 6000 deg K
>/=120 Lm/Watt for 4000 deg K
>/=110 Lm/Watt for 3000 deg K) Yes * Working life for LED : (Minimum 50
000 burning hours as per LM-80 report) Yes * Colour Rendering Index(CRI) ≥80 * Beam Angle ≥120 * Reflector type Diffuser * THERMAL MANAGEMENT Fixture/Luminaire should be die-cast aluminium CRCA/Extruded aluminium Yes * Capacitor shall be rated for a temperature of 105 deg. celsius or Yes * 30/55 better Junction temperature soldering temperature < 85 deg C * Operating temperature range -10 deg. C to +55 deg. C * Humidity Range 10 % to 95% RH * PROTECTION Short circuit Protection Yes * Over load protecton Yes * High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes * Insulation resistance between earth and current carrying part >100 M ohm * The luminaire shall be protected against surges and transients of >/=2.5 KV Yes * MARKING Manufactures Name and brand shall available on the body of the Luminaire Engraved/Embssed * Each LED liminaire shall have the manufacturer’s name
serial number
date of manufacture (month- year)
and lot number as identification mark inside each unit and the outside of each packaging box Yes * The operation characteristics such as rated voltage and rated power in watts shall be marked inside each LED luminaire unit Yes * REPORTS AND CERTIFICATIONS LED Make EVERLIGHT/EDISON BRIDGELUX NATIONSTAR/SEOUL SAMSUNG/OSRAM REFOND/NICHIA CREE/LUMILEDS PHILIPS/SYSKA LUMENMAX * LM 79 (Photometry) Yes * 31/55 (Ref.IS:16106:2012) report from Central Government LAB NABL/ILAC accrediated lab. Reports shall be furnish to the buyer on demand (LM-79 report shall have total lumen output
) LM 80 &TM21(Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer on demand (LM-80 report shall have the Photo Biological report of the LED Chip being used in the luminaire) Yes * Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes * Seller has to furnish Type test report to the buyer on demand Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * LED Luminaire for rcess type shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 2): 2012 as applicable on date Yes * * Bold specifications are the golden parameters. Consignees and Quantity 32/55 S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001
Raipur. (C.G.) 65 15 LED Luminaire (Recessed Luminaire) ( 6 ) ( Under PAC ) Make shreeg Model glimmer12rs Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values STANDARDS Conformity to Indian Standard IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 for Recess type * Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * Luminaire Class (as per Cl. 2.1 Section 2 of IS: 10322 (Part-1) Class I * Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 * Rating of Recess type LED Luminaire/System Wattage/Rated Power 12W * Light Intensity(System Lumens) 80 Lm/Watt for 3000 deg K
100 Lm/Watt for 6000 deg K Yes * Color temeprature (+/- 500 K) 6000 deg K * 33/55 Type of fixture (in feet) 1x1 (for 18W to 28W) 1x1 (for 3W to 16W)
2x2(30W to 48W) CONSTRUCTIONAL Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest (Minimum) IP20 * Mounting type Recess type * Diffuser material Acrylic * The luminaire body must be corrosion resistant epoxy powder coated/anadozing Yes * All fastners must be of nickel/chrome plated Yes * Number of electronic control gear (power supplies) 1 * Light Source SMD LED Chip as per LM 80/IS16106 * Warranty for free replacement 2 Years * ELECTRICAL EFFICIENCY MANAGEMENT Operating Voltage and frequency range 140V to 280 V at 50 Hz AC * Rated voltage 230 V AC 50 Hz * AC Power Factor ≥ 0.90 * Driver Efficiency ≥85 * Total Harmonics Distortion ( ≤ 20% (for upto 20W) (</=10% (for above 20W) Yes * The total circuit power shall not be more than 110 percent of the value declared by the manufacturer (as per Cl 8 of IS:16104:2012 lates) Yes * OPTICAL MANAGEMENT LED chip Efficacy (≥130 Lm/Watt for 6000 deg K
000 Yes * 34/55 burning hours as per LM-80 report) Colour Rendering Index(CRI) ≥80 * Beam Angle ≥120 * Reflector type Diffuser * THERMAL MANAGEMENT Fixture/Luminaire should be die-cast aluminium CRCA/Extruded aluminium Yes * Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes * Junction temperature soldering temperature < 85 deg C * Operating temperature range -10 deg. C to +55 deg. C * Humidity Range 10 % to 95% RH * PROTECTION Short circuit Protection Yes * Over load protecton Yes * High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes * Insulation resistance between earth and current carrying part >100 M ohm * The luminaire shall be protected against surges and transients of >/=2.5 KV Yes * MARKING Manufactures Name and brand shall available on the body of the Luminaire Engraved/Embssed * Each LED liminaire shall have the manufacturer’s name
and lot number as identification mark inside each unit and the outside of each packaging box Yes * 35/55 The operation characteristics such as rated voltage and rated power in watts shall be marked inside each LED luminaire unit Yes * REPORTS AND CERTIFICATIONS LED Make EVERLIGHT/EDISON BRIDGELUX NATIONSTAR/SEOUL SAMSUNG/OSRAM REFOND/NICHIA CREE/LUMILEDS PHILIPS/SYSKA LUMENMAX * LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government LAB NABL/ILAC accrediated lab. Reports shall be furnish to the buyer on demand (LM-79 report shall have total lumen output
) Yes * LM 80 &TM21(Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer on demand (LM-80 report shall have the Photo Biological report of the LED Chip being used in the luminaire) Yes * Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes * Seller has to furnish Type test report to the buyer on demand Yes * DC or AC supplied electronic control gear Yes * 36/55 for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) LED Luminaire for rcess type shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 2): 2012 as applicable on date Yes * * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001
Raipur. (C.G.) 6 15 LED Luminaire (Recessed Luminaire) ( 26 ) ( Under PAC ) Make shreeg Model glimmer18rs Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values STANDARDS Conformity to Indian Standard IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 for Recess type * Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * Luminaire Class (as per Cl. 2.1 Section 2 of IS: 10322 (Part-1) Class I * Types of LED Modules Type 3 * 37/55 as per the IS: 16103(Part-2)/2012 Rating of Recess type LED Luminaire/System Wattage/Rated Power 18W * Light Intensity(System Lumens) 80 Lm/Watt for 3000 deg K
100 Lm/Watt for 6000 deg K Yes * Color temeprature (+/- 500 K) 6000 deg K * Type of fixture (in feet) 1x4 (30W to 48W) 1x1 (for 3W to 16W)
2x2(30W to 48W) CONSTRUCTIONAL Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest (Minimum) IP20 * Mounting type Recess type * Diffuser material Acrylic * The luminaire body must be corrosion resistant epoxy powder coated/anadozing Yes * All fastners must be of nickel/chrome plated Yes * Number of electronic control gear (power supplies) 1 * Light Source SMD LED Chip as per LM 80/IS16106 * Warranty for free replacement 2 Years * ELECTRICAL EFFICIENCY MANAGEMENT Operating Voltage and frequency range 140V to 280 V at 50 Hz AC * Rated voltage 230 V AC 50 Hz * AC Power Factor ≥ 0.90 * Driver Efficiency ≥85 * Total Harmonics Distortion ( ≤ 20% (for upto 20W) (</=10% Yes * 38/55 (for above 20W) The total circuit power shall not be more than 110 percent of the value declared by the manufacturer (as per Cl 8 of IS:16104:2012 lates) Yes * OPTICAL MANAGEMENT LED chip Efficacy (≥130 Lm/Watt for 6000 deg K
000 burning hours as per LM-80 report) Yes * Colour Rendering Index(CRI) ≥80 * Beam Angle ≥120 * Reflector type Diffuser * THERMAL MANAGEMENT Fixture/Luminaire should be die-cast aluminium CRCA/Extruded aluminium Yes * Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes * Junction temperature soldering temperature < 85 deg C * Operating temperature range -10 deg. C to +55 deg. C * Humidity Range 10 % to 95% RH * PROTECTION Short circuit Protection Yes * Over load protecton Yes * High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes * Insulation resistance between earth and current carrying part >100 M ohm * The luminaire shall be protected against surges and transients Yes * 39/55 of >/=2.5 KV MARKING Manufactures Name and brand shall available on the body of the Luminaire Engraved/Embssed * Each LED liminaire shall have the manufacturer’s name
and lot number as identification mark inside each unit and the outside of each packaging box Yes * The operation characteristics such as rated voltage and rated power in watts shall be marked inside each LED luminaire unit Yes * REPORTS AND CERTIFICATIONS LED Make EVERLIGHT/EDISON BRIDGELUX NATIONSTAR/SEOUL SAMSUNG/OSRAM REFOND/NICHIA CREE/LUMILEDS PHILIPS/SYSKA LUMENMAX * LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government LAB NABL/ILAC accrediated lab. Reports shall be furnish to the buyer on demand (LM-79 report shall have total lumen output
) Yes * LM 80 &TM21(Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer on demand (LM-80 report shall have the Photo Biological report of the Yes * 40/55 LED Chip being used in the luminaire) Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes * Seller has to furnish Type test report to the buyer on demand Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * LED Luminaire for rcess type shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 2): 2012 as applicable on date Yes * * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001
Raipur. (C.G.) 26 15 LED Luminaire (Recessed Luminaire) ( 10 ) ( Under PAC ) Make shreeg Model glim15 Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values STANDARDS Conformity to Indian IS:10322/part * 41/55 Standard 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 for Recess type Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * Luminaire Class (as per Cl. 2.1 Section 2 of IS: 10322 (Part-1) Class I * Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 * Rating of Recess type LED Luminaire/System Wattage/Rated Power 16W * Light Intensity(System Lumens) 80 Lm/Watt for 3000 deg K
2x2(30W to 48W) CONSTRUCTIONAL Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest (Minimum) IP20 * Mounting type Recess type * Diffuser material Acrylic * The luminaire body must be corrosion resistant epoxy powder coated/anadozing Yes * All fastners must be of nickel/chrome plated Yes * Number of electronic 1 * 42/55 control gear (power supplies) Light Source SMD LED Chip as per LM 80/IS16106 * Warranty for free replacement 2 Years * ELECTRICAL EFFICIENCY MANAGEMENT Operating Voltage and frequency range 140V to 280 V at 50 Hz AC * Rated voltage 230 V AC 50 Hz * AC Power Factor ≥ 0.90 * Driver Efficiency ≥85 * Total Harmonics Distortion ( ≤ 20% (for upto 20W) (</=10% (for above 20W) Yes * The total circuit power shall not be more than 110 percent of the value declared by the manufacturer (as per Cl 8 of IS:16104:2012 lates) Yes * OPTICAL MANAGEMENT LED chip Efficacy (≥130 Lm/Watt for 6000 deg K
000 burning hours as per LM-80 report) Yes * Colour Rendering Index(CRI) ≥80 * Beam Angle ≥120 * Reflector type Diffuser * THERMAL MANAGEMENT Fixture/Luminaire should be die-cast aluminium CRCA/Extruded aluminium Yes * Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes * Junction temperature soldering temperature < 85 deg C * Operating temperature -10 deg. C to +55 deg. * 43/55 range C Humidity Range 10 % to 95% RH * PROTECTION Short circuit Protection Yes * Over load protecton Yes * High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes * Insulation resistance between earth and current carrying part >100 M ohm * The luminaire shall be protected against surges and transients of >/=2.5 KV Yes * MARKING Manufactures Name and brand shall available on the body of the Luminaire Engraved/Embssed * Each LED liminaire shall have the manufacturer’s name
and lot number as identification mark inside each unit and the outside of each packaging box Yes * The operation characteristics such as rated voltage and rated power in watts shall be marked inside each LED luminaire unit Yes * REPORTS AND CERTIFICATIONS LED Make EVERLIGHT/EDISON BRIDGELUX NATIONSTAR/SEOUL SAMSUNG/OSRAM REFOND/NICHIA CREE/LUMILEDS PHILIPS/SYSKA LUMENMAX * LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government LAB NABL/ILAC accrediated lab. Reports shall be furnish to the buyer on Yes * 44/55 demand (LM-79 report shall have total lumen output
) LM 80 &TM21(Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer on demand (LM-80 report shall have the Photo Biological report of the LED Chip being used in the luminaire) Yes * Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes * Seller has to furnish Type test report to the buyer on demand Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * LED Luminaire for rcess type shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 2): 2012 as applicable on date Yes * * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001
Raipur. 10 15 45/55 (C.G.) LED Luminaire (Recessed Luminaire) ( 1 ) ( Under PAC ) Make shreeg Model glamour1t Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values STANDARDS Conformity to Indian Standard IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 for Recess type * Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * Luminaire Class (as per Cl. 2.1 Section 2 of IS: 10322 (Part-1) Class I * Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 * Rating of Recess type LED Luminaire/System Wattage/Rated Power 6W * Light Intensity(System Lumens) 80 Lm/Watt for 3000 deg K
46/55 2x2(30W to 48W) CONSTRUCTIONAL Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest (Minimum) IP20 * Mounting type Recess type * Diffuser material Poly carbonate (UV stabilised) * The luminaire body must be corrosion resistant epoxy powder coated/anadozing Yes * All fastners must be of nickel/chrome plated Yes * Number of electronic control gear (power supplies) 1 * Light Source SMD LED Chip as per LM 80/IS16106 * Warranty for free replacement 2 Years * ELECTRICAL EFFICIENCY MANAGEMENT Operating Voltage and frequency range 140V to 280 V at 50 Hz AC * Rated voltage 230 V AC 50 Hz * AC Power Factor ≥ 0.90 * Driver Efficiency ≥85 * Total Harmonics Distortion ( ≤ 20% (for upto 20W) (</=10% (for above 20W) Yes * The total circuit power shall not be more than 110 percent of the value declared by the manufacturer (as per Cl 8 of IS:16104:2012 lates) Yes * OPTICAL MANAGEMENT LED chip Efficacy (≥130 Lm/Watt for 6000 deg K
000 burning hours as per LM-80 report) Yes * Colour Rendering ≥80 * 47/55 Index(CRI) Beam Angle ≥120 * Reflector type Diffuser * THERMAL MANAGEMENT Fixture/Luminaire should be die-cast aluminium CRCA/Extruded aluminium Yes * Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes * Junction temperature soldering temperature < 85 deg C * Operating temperature range -10 deg. C to +55 deg. C * Humidity Range 10 % to 95% RH * PROTECTION Short circuit Protection Yes * Over load protecton Yes * High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes * Insulation resistance between earth and current carrying part >100 M ohm * The luminaire shall be protected against surges and transients of >/=2.5 KV Yes * MARKING Manufactures Name and brand shall available on the body of the Luminaire Engraved/Embssed * Each LED liminaire shall have the manufacturer’s name
and lot number as identification mark inside each unit and the outside of each packaging box Yes * The operation characteristics such as rated voltage and rated Yes * 48/55 power in watts shall be marked inside each LED luminaire unit REPORTS AND CERTIFICATIONS LED Make EVERLIGHT/EDISON BRIDGELUX NATIONSTAR/SEOUL SAMSUNG/OSRAM REFOND/NICHIA CREE/LUMILEDS PHILIPS/SYSKA LUMENMAX * LM 79 (Photometry) (Ref.IS:16106:2012) report from Central Government LAB NABL/ILAC accrediated lab. Reports shall be furnish to the buyer on demand (LM-79 report shall have total lumen output
) Yes * LM 80 &TM21(Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer on demand (LM-80 report shall have the Photo Biological report of the LED Chip being used in the luminaire) Yes * Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes * Seller has to furnish Type test report to the buyer on demand Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * 49/55 LED Luminaire for rcess type shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 2): 2012 as applicable on date Yes * * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001
Raipur. (C.G.) 1 15 LED Luminaire (Recessed Luminaire) ( 1 ) ( Under PAC ) Make shreeg Model glamour30 Technical Specifications * As per GeM Category Specification Specification Specification Name Values Allowed Values STANDARDS Conformity to Indian Standard IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 for Recess type * Photo biological safety of LEDs used shall be as per IS:16108/2012 (exempt group) Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * Luminaire Class (as per Cl. 2.1 Section 2 of IS: 10322 (Part-1) Class I * Types of LED Modules as per the IS: 16103(Part-2)/2012 Type 3 * 50/55 Rating of Recess type LED Luminaire/System Wattage/Rated Power 30W * Light Intensity(System Lumens) 80 Lm/Watt for 3000 deg K
2x2(30W to 48W) CONSTRUCTIONAL Ingress Protection (IP Rating) as per IS:10322 (Part 1):1982 latest (Minimum) IP20 * Mounting type Recess type * Diffuser material Acrylic * The luminaire body must be corrosion resistant epoxy powder coated/anadozing Yes * All fastners must be of nickel/chrome plated Yes * Number of electronic control gear (power supplies) 1 * Light Source SMD LED Chip as per LM 80/IS16106 * Warranty for free replacement 2 Years * ELECTRICAL EFFICIENCY MANAGEMENT Operating Voltage and frequency range 140V to 280 V at 50 Hz AC * Rated voltage 230 V AC 50 Hz * AC Power Factor ≥ 0.90 * Driver Efficiency ≥85 * Total Harmonics Distortion ( ≤ 20% (for upto 20W) (</=10% (for above 20W) Yes * The total circuit power Yes * 51/55 shall not be more than 110 percent of the value declared by the manufacturer (as per Cl 8 of IS:16104:2012 lates) OPTICAL MANAGEMENT LED chip Efficacy (≥130 Lm/Watt for 6000 deg K
000 burning hours as per LM-80 report) Yes * Colour Rendering Index(CRI) ≥80 * Beam Angle ≥120 * Reflector type Diffuser * THERMAL MANAGEMENT Fixture/Luminaire should be die-cast aluminium CRCA/Extruded aluminium Yes * Capacitor shall be rated for a temperature of 105 deg. celsius or better Yes * Junction temperature soldering temperature < 85 deg C * Operating temperature range -10 deg. C to +55 deg. C * Humidity Range 10 % to 95% RH * PROTECTION Short circuit Protection Yes * Over load protecton Yes * High voltage test (1.5 KV for one minute between supply terminals and body of the unit) Yes * Insulation resistance between earth and current carrying part >100 M ohm * The luminaire shall be protected against surges and transients of >/=2.5 KV Yes * MARKING Manufactures Name Engraved/Embssed * 52/55 and brand shall available on the body of the Luminaire Each LED liminaire shall have the manufacturer’s name
) Yes * LM 80 &TM21(Ref. IS:16105:2012) Report and Photo biological report for LED report from Central Government Lab NABL/ILAC accrediated lab. Reports shall be furnish to the buyer on demand (LM-80 report shall have the Photo Biological report of the LED Chip being used in the luminaire) Yes * 53/55 Availability of test Report from Central Government Lab NABL/ILAC accrediated lab to Indian Standrad IS:10322/part 5/sec-2/2012 and IS 16107 (Part 2/Sec 1) : 2012 Yes * Seller has to furnish Type test report to the buyer on demand Yes * DC or AC supplied electronic control gear for LED Module shall comlpy as per IS:15885 (Part 2/Sec.13) Yes * LED Luminaire for rcess type shall comply with Complusory Registration(CRS) of BIS for safety as per IS 10322 (Part 5/Section 2): 2012 as applicable on date Yes * * Bold specifications are the golden parameters. Consignees and Quantity S.No. Consignee Address Quantity Delivery Days 1 Mahadev Bhoi 492001
Raipur. (C.G.) 1 15
