Renovation work of second and third floor for office of Chief Electoral West Bengal at shipping house BBD Bag, Kolkata

S NO DESCRIPTION TOTAL AMOUNT (Rs.)

GRAND TOTAL (DSR + Non-DSR/MR) 36,708,492.00

CEMENT CONCRETE: Providing and laying in position CEMENT CONCRETE of specified grade exluding

1.01 the cost of centring and shuttering-all work upto plinth level.

4.1.8 1: 4: 8 (1 Cement: 4 coarse sand: 8 graded stone aggregate 40mm nominal size) CUM 6.00 6,812.00 40,872.00

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with 15 micron anodising In

Natural Finish. Thickness 1.30 to 1.50mm. Designed to conceal screws. Seamless finish. Complete with

LAMINATED WOODEN FLOORING: Providing and laying 8mm thick AC5 grade laminate wooden flooring

having good castor chair and furniture resistance strength. Plank dimension to be 606x103 mm with clock

locking system and wax coating for better sound resistance. Impact and abrasion resistance to be of high

grade having class EN 13329. The flooring shall be laid with 2mm thick underlay and PVC sheet and

VITRIFIED TILES: Providing and laying vitrified floor and wall tiles in different sizes (thickness to be

1.05 11.41A specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of -

approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse

11.41A.2.1 Size of jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic

coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling/ grouting

GRANITE: Providing and laying Polished Granite stone flooring in required design and patterns, in linear

as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm

thick stone slab over 20 mm (average) thick base of cement mortar 1: 4 (1 cement: 4 coarse sand) laid

and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching

shade including rubbing, curing and polishing etc. all complete as specified and as directed by the

Engineer-in-Charge.

11.56.1 Polished Granite stone slab of colour Black, Cherry/ Ruby Red or equivalent sq m 12.00 4,481.30 53,775.60

FALSE CEILING WORKS -

1 Digitally signed by AMIT

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height including providing and fixing of

frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of

120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6

mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling

with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle

hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to

centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm

each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every

2 12.45 junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm -

long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm

long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter

channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing

to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing

tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two

coats of primer suitable for board, all as per manufacturer's specification and also including the cost of

making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably

fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the

cost of painting with

12.5mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS

certification marks)

Providing and Fixing 15 mm thick densified tegular edged eco friendly light

weight calcium silicate false ceiling tiles of approved texture of size 595 x

595 mm in true horizontal level, suspended on inter locking metal grid of

hot dipped galvanised steel sections (galvanising @ 120 grams per sqm

including both side) consisting of main ‘T’ runner suitably spaced at joints

to get required length and of size 24x38 mm made from 0.33 mm thick

(minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size

24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced

between main’T’ at 600 mm centre to centre to form a grid of 1200x600

mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made

of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x

600 mm panel to from grid of size 600x600 mm, resting on periphery walls

12.53 /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 sq m 1075.00 2,158.15 2,320,011.25

mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs

at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm

interval and laying 15 mm thick densified edges calicum silicate ceiling

tiles of approved texture in the grid, including, cutting/ making opening

for services like diffusers, grills, light fittings, fixtures, smoke detectors

etc., wherever required. Main ‘T’ runners to be suspended from ceiling

using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5

mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with

galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200

mm centre to centre along main ‘T’. Bottom exposed with 24 mm of all

T-sections shall be pre-painted with polyster baked paint, for all heights,

as per specifications, drawings and as directed by Engineer-in-Charge.

2 Digitally signed by AMIT

Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm

module which includes providing and fixing ‘C’ wall angle of size 20x30x20

mm made of 0.5 mm thick pre painted steel along the perimeter of the

room with help of nylon sleeves and wooden screws at 300 mm center to

centre, suspending the main C carrier of size 10x38x10 mm made of G.I

steel 0.7 mm thick from the soffit with the help of soffit cleat 37x27x25x1.6

mm, rawl plugs of size 38x12 mm and C carrier suspension clip and

main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee

having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm

thick is then fixed to the main C carrier and in direction perpendicular to

12.54.1 it at 600 mm centers with the help of suspension brackets. Wherever the Sqm. 60.00 2,221.70 133,302.00

main C carrier and spring T have to join, C carrier and spring T connectors

have to be used. All sections to be galvanized @ 120 gms/sqm (both side

inclusive), fixing with clip in tiles into spring T with :

12.54.1 GI Metal Ceiling Clip in plain Beveled edge global white color

tiles of size 600x600 and 0.5 mm thick with 25 mm height,

made of G I sheet having galvanizing of 100 gms/ sqm

(both sides inclusive) and electro statically polyester powder

coated of thickness 60 microns (minimum), including factory

painted after bending.

13.68 French spirit polishing: -

2.03 13.68.1 Two or more coats on new works including a coat of wood filler sq m 300.00 446.25 133,875.00

WALL FINISHES WORKS -

SINGLE GLAZED FIXED PARTITION WITH 10MM GLASS): Supply & Installation of Aluminium Partition

with Clip-on / U-Section of size 30mm x 21mm with 2.5mm Wall thickness in matt black/ Natural Alu finish.

Partition to be provided with suitable gaskets for insertion of 10mm thick clear toughened glass. Partition

Glass joineries consists of two-way Polycarbonate I-profiles, 90 Degree Polycarbonate L-Junction and

3 MR Polycarbonate T-Junction profiles. Polycarbonate profile joineries to be fixed with double sided adhesive sq m 180.00 11,180.00 2,012,400.00

tape & profiles to be inserted in the joint instead of sealing it with sealants. Polycarbonate profiles to be

used to give continuity glass effect. Hardware for fixing profiles to be used as per manufacturer standard.

Costs should be inclusive of necessary Hardware for fixing of profiles & installation charges.

Providing and fixing 12 mm thick frameless toughened glass door shutter

of approved brand and manufacture, including providing and fixing top &

bottom pivot & double acting hydraulic floor spring type fixing arrangement

21.18 and making necessary holes etc. for fixing required door fittings, all Sqm. 48 5,325.90 255,643.20

complete as per direction of Engineer-in-charge (Door handle, lock and

stopper etc.to be paid separately).

Door handle, lock and stopper etc. for per set of glass door

WOODEN DOOR FRAMES: Providing wood work in frames of doors, windows, clerestory windows and

other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia

9.1.1 Second class teak wood cu m 5.00 142,949.70 714,748.50

WOODEN BATTENS: Providing and fixing specified wood frame work consisting of battens 50x25mm

fixed with rawl plug and drilling necessary holes for rawl plug etc. including priming coat complete.

8.27.1 Kiln seasoned and chemically treated hollock wood CUM 5.00 187,277.65 936,388.25

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part 1) decorative type, core of

block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with

3 Digitally signed by AMIT

9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws SQM 40.00 3,473.85 138,954.00

9.24 Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) -

3.06 9.24.1 Rectangular or square SQM 5.00 199.15 995.75

WOODEN LIPPING: Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth

on all edges of flush door shutters (over all area of door shutter to be measured).

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to

IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight

upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good

the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S.

21.4.2 With brass cover plate minimum 1.25 mm thickness SET 25 2,966.10 74,152.50

FLUSH DOOR HANDLE: H type pull handle size 25x450mm C/C includes Stainless steel back to back

fixing accessories for steel,wood & glass door: 302 grade

WOODEN DOOR LOCK: Providing and Fixing LOCK ML DL 72/55, Dead lock in 55mm backset includes

strike plate and CYLINDER EPC K35/K35, double cylinder in 70mm length with 3keys and fixing , handle

3.10 LH 100 Escutcheon round Finish: BSS

GLASS FILMS: Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-

effect film to reproduce Sand-blasting effect on glass with customised designs, thickness of 2 mil (0.05mm)

without adhesive & 3mil (0.8)with adhesive having minimum tensile strength of 3.5 pound/inch at 73 F(0.6

kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch (0.7 kg/cm) on Acrylic, Glass

LACQUERED GLASS: Providing and fixing of 6mm thick annealed SGG Planilaque Evolution (premium

GRIHA rated lacquered glass from Saint-Gobain) of approved color by Architect/ Client / Customer, fixed

with SGG ULTRAFIX (compatible neutral core silicon/ double sided tape) on a perfectly leveled 12mm

MR thick water proof marine plywood / MDF / Mineral fibre board which is mounted on the RCC wall/any other SQM 50.00 5,004.00 250,200.00

structure. Lacquered glass must be made industrially (via curtain coating process); opaque (if viewed

against a support wall), coated with PU lacquer (50 micron thick); color consistency (measured by Minolta

spectrophotometer CM5081); highly durable (passes PERSOZ hardness test for minimum 220 oscillatios);

3.12 humid resistant (conforms to BS EN 1036 1999); environmentally friendly (no lead, no arsenic, no copper, -

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut

for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved

shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints

treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing,

8.2.2 Granite stone slab of colour black, Cherry/Ruby red -

4 Digitally signed by AMIT

WINDOW BLINDS: Providing & supplying of Window Blinds as per the approved sample double

honeycomb blackout shades having honeycomb within honeycomb with easy rise operating system as

per following specifications fabric specifications:

• Original Non-woven honeycomb shade shaving soft fabric appearance and high energy-efficient

fabric with high tear strength constructed out of Anti-static, resilent, colour fast & Sanitized Treat

100% spun bonded non-woven polyester fiber & precision manufacture to form a hexagonally shaped

duette pleat. The Fabric is GREENGUARD certified and can attain an NRC value of 0.75. Certificates to be

provided at the time of delivery of material at site. Pleat dimension ¾ ”Honeycomb within a Honeycomb”

with 3 air pockets for maximum energy efficiency.

MR • Shadings are duotone, with neutral tone facing the exterior and color facing the interior The Head rail. SQM 120.00 21,200.00 2,544,000.00

Shall measure 50 wide and 35mm deep & thick 1.25mm extruded from alu. alloy& shall be powder

coated to a smooth finish with a thickness of 40 microns. Fabric shall be constructed from spun-

bonded polyester fiber, precision manufactured to form a hexagonally shaped, dual pleat, cellular

construction. All cords & cord holes shall be fully concealed inside the fabric structure. As each

of the hexagonal cells is formed individually, pleats operate independent of each other providing

superior pleat retention & structure strength. Installation brackets. shall be of high-tension spring steel

suitable for overhead & wall mounting 30mm Duette Hartford mounting bracket. Head rail covered with

Sydney Valance of height 80mm made up of Aluminium & L shape moving Rail includes “Click & Engage"

method of dimension 50mmx55mmsticked with integrated moving rail magnets provide a streamlined look,

PELMET: Fabricate and install pelmet made of 19mm thick board, up to 300mm high and in line with

external glazing as per details of Architect. Rate to include finishing exposed surfaces of the Pelmet with

13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the

surface even and smooth complete sqm 900.00 262.70 236,430.00

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic

13.85 Compound ) content. -

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic

Compound) content less than 50 grams/ litre of approved brand and manufacture, including applying

5.5mm THICK HDHMR BOARD (BOTH SIDE RAW): Providing and fixing in wall lining, partitions etc.

Confirming to ASTM E-84-2021 class1 BOTH side raw, having even grade low emission, high moisture

resistance, fire resistance, borer, termite & fungus resistance, green material and environmental friendly Sqm 60.00 504.00 30,240.00

3.20 MR with necessary fixing arrangement and screws etc. , complete as per direction of Engineer-in-Charge

5.5mm thick HDHMR Board -

ALUMINIUM FRAME: Providing and fixing aluminium work for doors, windows, ventilators and partitions

with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved

make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including

3.22 necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/

neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed

mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P.

21.1.1.3 brass / stainless

Polyester powdersteel screws,

coated all complete

aluminium as per

(minimum architectural

thickness drawings

of polyester and the

powder directions

coating of Engineer-in-

5 Digitally signed by AMIT

Providing and fixing 12 mm thick frameless toughened glass door shutter

of approved brand and manufacture, including providing and fixing top &

bottom pivot & double acting hydraulic floor spring type fixing arrangement

3.23 9.156.1 and making necessary holes etc. for fixing required door fittings, all Sqm. 400 1,031.50 412,600.00

complete as per direction of Engineer-in-charge (Door handle, lock and

stopper etc.to be paid separately)..

PARTITION INSULATION: Providing and Fixing 50 mm thick extruded polystyrene rigid Polyester rigid

3.24 26.7 insulation boards for cavity as per specifications Sqm 250 1,004.55 251,137.50

LAMINATE PANELLING: Providing & Fixing decorative high pressure laminated sheet of plain/ wood grain

in gloss/ matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding

9.127.2 quality

1.0 mmconforming

thick to IS : 2046 Type S, including cost of adhesive of approved quality. SQM 400.00 1,224.65 489,860.00

TOTAL WALL FINISHING WORKS

4 MISCELLANEOUS WORKS -

WATERPROOFING: Providing and laying water proofing treatment to vertical and horizontal surfaces of

depressed portions of W.C., kitchen and the like consisting of:

(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to

IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.

(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing

4.01 22.3 compound in recommended proportion including rounding off junction of vertical and horizontal surface. SQM 150.00 769.60 115,440.00

(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide

and pasted to each other with bitumen @ 1.7 kg/sqm).

Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by

4.02 1.1.18 mechanical transport including loading, transporting, unloading to approved municipal dumping ground for cum 12.00 494.10 5,929.20

lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. Note - item to be applicable

in urban areas having directions for restricted hours for movement/ plying of load carrying motor vehicle of -

Brick work with non modular fly ash bricks conforming to 1S:12894, class designation 10 average

compressive strength in super structure above plinth level up to floor V level in:

6.4.1 Cement mortar 1:4 (1 cement : 4 coarse sand) cum 6.00 8,962.35 53,774.10

4.04 6.45 Half brick masonry with non modular fly ash bricks of class designation 10, conforming to IS :12894, in -

Cementstructure above

mortar 1: 3 (1 plinth

cement:upto floor V sand)

4.05 13.4 12 mm cement plaster of mix: 1: 4 (1 cement: 4 coarse sand) sqm 180.00 357.35 64,323.00

DEMOLITION & DISMANTLING WORKS -

Demolition of brickwork manually/ by mechanical means including stacking of serviceable material and

disposal of unserviceable material within 50 metres lead as per the direction of the engineer in charge

Dismantling door, windows and clerestory widows (steel or wood) shutter including chowkats, architrave,

holdfasts etc complete and stacking within 50 metres lead

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or

round bars etc. including priming coat with approved steel primer all complete.

9.48.1 Fixed to openings /wooden frames with rawl plugs screws etc. kg 300.00 238.50 71,550.00

6 Digitally signed by AMIT

Grand Total (DSR + Non-DSR/MR) 14,575,329.75

Grand Total (DSR + Non-DSR/MR) 14,575,329.75

7 Digitally signed by AMIT

SCHEDULE OF QUANTITIES: INTERNAL & EXTERNAL PLUMBING

S NO DSR/ MR DESCRIPTION UNIT QTY RATE AMOUNT (Rs.)

DSR 2023 (DSR) (NON DSR)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type

A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,

1 12.41 (i) Single socketed pipes.

a MR 160 mm diameter Metre 3 754.80 2264.40

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain

water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm

2 12.42 gap for thermal expansion. -

a 12.42.2 Single pushfit Coupler -

b 12.42.3 Single tee with door -

d 12.42.6 Shoe (Plain) -

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by

means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work

and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not

less than 440 grams.

5 13.7 12 mm cement plaster finished with a floating coat of neat cement of mix : -

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved

brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual

6 17.81 flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including Each 18 18212.90 327,832.20

making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste

7 17.7 of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever -

1 Digitally signed by AMIT

White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of

approved quality and make, including painting of fittings and brackets, cutting and making good the walls

8 17.7A wherever required:-

White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and

stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls

17.10 wherever required :

17.10.1 Kitchen sink with drain board -

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction

of Engineer-in-charge

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by

11 Engineer in charge.

(a) 15 mm nominal dia Each 1 6940.75 6,940.75

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x

370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side,

12 17.80 including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in- Each 21 7979.20 167,563.20

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

17.28.2 Flexible pipe -

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete

14 17.31 with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. Each 13 1607.95 20,903.35

17.34 Providing and fixing toilet paper holder : -

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water

supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing.

16 18.7 This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per -

direction of Engineer in Charge.

Internal work - Exposed on wall -

a) 18.7.1 15 mm nominal dia Pipes metre 25 286.80 7,170.00

b) 18.7.2 20 mm nominal dia Pipes metre 10 335.00 3,350.00

c) 18.7.3 25 mm nominal dia Pipes metre 10 401.55 4,015.50

d) 18.7.4 32 mm nominal dia Pipes metre 10 518.75 5,187.50

2 Digitally signed by AMIT

e) 18.7.5 40 mm nominal dia Pipes metre 10 702.95 7,029.50

f) 18.7.6 50 mm nominal dia Pipes metre 934.15 -

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water

supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This

17 18.8 includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making -

good the same including testing of joints complete as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc. -

a) 18.8.1 15 mm nominal dia Pipes metre 70 497.80 34,846.00

b) 18.8.2 20 mm nominal dia Pipes metre 45 537.60 24,192.00

c) 18.8.3 25 mm nominal dia Pipes metre 18 627.25 11,290.50

d) 18.8.4 32 mm nominal dia Pipes metre 18 739.30 13,307.40

18 18.12 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. -

External work -

a) 18.12.5 40 mm dia nominal dia Pipes Metre 18 617.05 11,106.90

b) 18.12.6 50 mm dia nominal dia Pipes Metre 13 762.15 9,907.95

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee,

19 including cutting and threading the pipe etc. complete :

18.13.2 50 to 80 mm nominal bore Each 1785.35 -

18.21 Providing and fixing uplasticised PVC connection pipe with brass unions -

18.21.2.1 15 mm nominal bore Each 97.75 -

18.22 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : -

18.22.1 100 mm diameter Each 193.95 -

Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 : vent

pipes of Under ground tank complete.

(Tank Vent Pipe) -

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :

a) 18.40.5 40 mm diameter pipe Metre 13 25.25 328.25

b) 18.40.6 50 mm diameter pipe Metre 13 30.50 396.50

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work :

a) 18.41.5 40 mm dia nominal bore Metre 13 167.00 2,171.00

b) 18.41.6 50 mm dia nominal bore Metre 18 173.25 3,118.50

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover

27 18.48 and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings per litre 11.00 -

and the base support for tank.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and

28 weighing not less than 690 gms.

18.51.1 15mm nominal bore Each 1 798.95 798.95

3 Digitally signed by AMIT

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality

29 conforming to IS:8931

18.53.1 15mm nominal bore Each 1 574.30 574.30

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per

30 18.53A direction of Engineer-in-charge. Each 12 74.80 897.60

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated

aluminium rod with L.P./ H.P.H.D. plastic ball.

a) 18.62.4 40 mm nominal bore, 206 mm long, weighing not less than 690 gms Each 737.20 -

b) 18.62.5 50 mm nominal bore, 242 mm long, weighing not less than 1240 gms Each 1375.95 -

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after

insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

32 18.77 nominal size), including finishing complete so as to make it leak proof. Each 3.00 452.00 1,356.00

Providing and fixing CP Brass liquid soap container of standard shape with bracket of the same materials

with snap fittings of approved quality and colour.

Providing and fixing CP Brass towel ring with concealed fittings arrangement of approved quality and

36 MR Providing and fixing CP Brass Coat Hook of approved quality and colour Each 1 683.00 683.00

37 MR Providing and fixing C.P. brass Two way bib cock of approved quality conforming to IS:8931. Each 1 1699.00 1699.00

Providing and fixing CP Health faucet to european type W.C. of approved quality and make as approved

by engineer in charge.

Providing and fixing CP Brass Single lever mixer for sink of quality & make as approved by Engineer in

charge. (a) 15 mm nominal dia.

Providing and fixing CP Brass towel rail complete with brackets with CP brass screws with concealed

fittings arrangement of approved quality and colour.

Providing and fixing CP Brass soap Dish Holder with concealed fitting arrangements, of approved quality

Providing and fixing rectangular shape Stainless steel grating with frame for floor traps or drains of

required pattern including cutting and making good the floors complete.

Supply installation, testing and commissioning of water cooler with Inbuilt RO purification+UV(50LPH) .Cooling

capacity shall be 60Litre and storage capacity shall be 80Litre. Its should have 7 stages purification process,fully

automatic,rectangular tank with Forced fin and tube condenser,Non-corrosive SS-304 outer body,Food-grade SS-

43 MR 304 stainless steel inner tank (18/8 or 18/10),PUF insulation,Reciprocating compressor with R22 Refrigerant.Water Each 79780.00 - 0.00

outlet temp is aprrox 17 deg C, Operating power supply 230+10% V AC, 50 Hz, 1 PH, No of Cold water Faucet-2.

4 Digitally signed by AMIT

Supply, Installation, testing and commissioning of storage type electric hot water heater made out of heavy gauge

steel jacket finished with rust proof baked-on glossy white enamel paint, inside glass lined heavy gauge steel tank,

25 mm thick polyurethane foam insulation, thermostatically controlled immersion heater with pilot neon lamp,

44 MR replaceable magnesium anode bar, suitable for 8.0 bar maximum working pressure, cold water inlet and hot water -

outlet pipe, suitable length of electrical cable and 15 amp 3 pin plug top, complete in all respect including testing etc.

Supply, Installation, Testing and Commisioning of Vessel type TABLE TOP BASIN having minimum SIZE:

630x460x130mm thinner edges and rimless bowl as per the color choice of the engineer in charge

TOTAL OF PLUMBING WORKS 826,472.65 666678.40

Grand Total (DSR + Non-DSR/MR) 1493151.05

Grand Total (DSR + Non-DSR/MR) 1493151.05

5 Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

S NO DESCRIPTION UNIT QTY RATE

DSR (INR) NON-DSR (INR)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm

FRLS PVC insulated copper conductor single core cable in surface / recessed

Group C class PVC conduit, with modular switch, modular plate, suitable GI box

Wiring for group controlled (looped) light point/ fan point/call bell point (without

independent switch etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor

C cable in surface/ recessed PVC conduit, and earthing the point with 1.5

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper

3 1.12 conductor single core cable in surface/ recessed medium class PVC conduit Metre 3000 334.00 1,002,000.00

alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable

for loop earthing as required.

Supplying and fixing following modular switch/ socket on the existing modular plate

& switch box including connections but excluding modular plate etc. as required.

5/6 amps switch

15/16 amp switch

3 pin 5/6 amp socket outlet

6 pin 15/16 amp socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the

existing modular plate switch box including connections but excluding modular

plate etc. asand

Supplying required.

fixing following size/module, GI box along with Modular base &

cover plate on existing modular metal boxes etc. as required.

6 LIGHT & POWER PLUGS -

Supplying and fixing suitable size GI box with modular plate and cover in front on

surface or in recess, including providing and fixing 3 pin 5/6 A modular socket

Supplying andAfixing

modular switch,

suitable connections

size GI box withetc. as required.

modular plate and cover in front on

surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular

socket outlet and 15/16 A modular switch, connections etc. as required.

1 Digitally signed by AMIT

Supplying and fixing suitable size GI box with modular plate and cover in front on

surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular

socket outlet and 2 nos. 5/6 Amp modular switch, connections etc. as required. (For -

SUBMAIN AND CONTROL WIRING -

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR

PVC insulated copper conductor, single core cable in surface/ recessed medium

2 X 1.5 sq. conduit

mm + 1as required

X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature

circuit breaker suitable for inductive load of following poles in the existing MCB DB

Single with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, TPN MCB in the existing

MCB DB complete with connections, testing and commissioning etc. as required.

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways

2mm thick along with required suitable number of GI couplers for joining raceways

and fixing GI brackets

300mmx38mm(GI) - 3 and all accessories complete in all respect as per the

225mmx38mm(GI) - 3 compartment

GI CABLE TRAYS -

Supplying and installing following size of perforated Hot Dipped Galvanised Iron

cable tray (Galvanisation thickness not less than 50 microns) with perforation not

depth X sections, joined with connectors, suspended from

1.6 mm thickness

2 Digitally signed by AMIT

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

Total of Electrical Works 1,760,746.00 553,294.06

Grand Total (DSR + MR)

Grand Total (DSR + MR)

3 Digitally signed by AMIT

SCHEDULE OF QUANTITIES: LIGHTING FIXTURES

DSR AMOUNT (RS.)

S No Description Unit Qty RATE DSR (INR) NON-DSR (INR)

LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120 lm/Watt )

Supplying, installation, Testing & Commissioning of LED Recessed/ surface Down

lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA

and prismatic diffuser and construction as per IS: 10322 with driver as per the

requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency

50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge

protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95,

IP20, CRI >80 , UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below

1 1.1 5%), life time (LED,Driver & electrical circuitary), of minimum 50000 Burning Hours with

70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /

6000°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) <3,

Maximum power consumption should not more than the specified rating and Fixture

shall be confirming to relevant BIS standards and trade mark certificate (T.C.).

Manufacturers Word Mark/ Name Engraved/ Embossing/ Screen printing on housing

Complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated

copper conductor single core cable and earthing etc. as required with Minimum 5 year

OEM warranty. System lumen efficacy ≥105 and <120 lm/Watt output . LM79 & LM80

Test report from NABL lab for all testing required for LED fixtures as per BIS shall nos 10

Supply of Integral, SMD 4x1 Backlit LED Panel, IP 20, 30W LED recessed mounted

fixture with system efficacy of minimum 100lm/W and system lumen output of minimum

3000lm, operating in ambient temperature of 0⁰C to 45⁰C at 50Hz frequency. Luminaire

shall have CRCA housing coated in white (RAL9016) with translucent HET diffuser for

uniform illumination and wider light distribution. LEDs used in the product shall comply

with IEC 62471. LM 80-08 compliant LEDs from reputed makes such as Nichia/Cree/

Bridgelux/ Lumiled/ Osram/Seoul should be provided. The LED shall comply with L70 life

of 50000 burning hours tested at maximum current. The LEDs used should be with CCT

2 MR of 4000 K and CRI of Minimum 80. LED Driver shall be Isolated type, Constant Current nos 50 3245.00 162250.00

topology driver with proper heat sink for heat dissipation suitable to operate in input

voltage range of 140V to 300V (nominal rated voltage – 240V) with 4KV internal surge

protection, Power factor of minimum 0.95 and total harmonic distortion (THD) of less

than or equal to 10% should be integral to the luminaire. Manufacturer shall have

inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80

reports need to be submitted from a NABL/UL accredited lab to verify above parameters.

Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106

Public Digitally signed by AMIT

Supply of 30W, suspended by 1.5m suspension wire, 4 feet linear, IP20, SMD LED

luminaire with system efficacy of 110 lumen/watt and system lumen output of 3300

lumen, operating in an ambient temperature of 0⁰C to 45⁰C. Operating at 50Hz

frequency, luminaire shall have extruded aluminium housing in white with high efficiency

translucence diffuser and must have provision for end to end seamless connectivity.

EMC package of wattage of 0.2-0.5 W LEDs used in the product shall comply with IEC

62471 for Photo-biological safety. LM 80-08 compliant LEDs from reputed makes such

as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. The LED shall

3 MR comply with L70 life of 50000 burning hours tested at maximum current. The LEDs used nos 20 4000.00 80000.00

should be with CCT of 4000 K and CRI of Minimum 80, with MacAdam CCT binning ≤3

mounted on 1.6mm FR4 / MCPCB with 35 micron cu layer. LED Driver shall be Isolated

type, Constant Current topology driver with proper heat sink for heat dissipation suitable

to operate in input voltage range of 140V to 300V (nominal rated voltage – 240V) with

3KV internal surge protection, Power factor of minimum 0.95, driver efficacy of minimum

85% and total harmonic distortion (THD) of less than or equal to 10% should be integral

to the luminaire. Manufacturer shall have inhouse lab approved by NABL or ministry of

science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL

accredited lab to verifysupply,

Design, manufacture, above parameters. Compliance

installation, and to Indian

commissioning of Standards of IS10322

a Electronically Driven,

Non Dimmable (but capable for dimming with just changing the Driver, if required in

future) customized translucent ceiling-mounted fabric and light engine. Sketch Lighting

make Illuminated Ceiling, or equivalent from any approved makes, matching below

specifications. from any approved makes The light box will be installed as per the

architectural requirements and must meet the following technical specifications. The

light box will be ceiling-mounted, size as approved by the architect. The ceiling box

should have a uniform depth of 250 mm or as requested by the light manufacturer for

4 MR spotless and glare-free illumination. Structure: The side walls of the light box will be SQM 53 6000.00 318000.00

constructed by the GC as part of the ceiling. Wooden box which is not part of this item,

should be made from 18 mm thick moisture and termite-resistant plywood or HDDMR

(High-Density High-Moisture Resistant Board), as approved by the architect. The roof of

the box shall also be made of the same moisture and termite-resistant plywood or

Interior Finish: The inner side of the box shall be primed and painted in matte white for

even light reflection and the white part should not be visible after installation of the fabric.

Thermal Management: Before installing the LED light engine, the interior of the light box

TOTAL be equipped with Thermal Interface Material for optimal heat dissipation. Thermally 39750.08 560250.00

TOTAL (DSR + Non-DSR) 600000.08

Public Digitally signed by AMIT

SCHEDULE OF QUANTITIES: EPABX (TELEPHONE & INTERCOM SYSTEM)

S NO DESCRIPTION Unit QTY RATE

MR DSR (INR) NON-DSR (INR)

Supply, Installation, Testing & Commissioning of EPABX with 2

PRI and 300 analog extension expandable till 500 extensions

capable of being PCM/TDM with voice mail, auto apending , call

1 MR forwarding etc facilities with operator console complete in all Nos 1 768,711.00 - 768,711.00

respect as per the directions of engineer in charge and all complete

with License & OEM Support of 3 years

SITC of Analog type Master /KTS Phones complete with handset

having features like digital display, redial, contact memory,

multiple direct/landline support (min. 6 keys), call hold /transfer &

2 MR pause, electronic volume control, handsfree speaker phone etc. Nos 25 6,500.00 - 162,500.00

including telephone/power cords etc. as required.

SITC of Analog type Phones complete with handset having features

like digital display, last number redial, electronic volume control,

handsfree speaker phone etc. including telephone/power cords etc.

1 Digitally signed by AMIT

Schedule of Quantities: Audio Visual System

S NO DESCRIPTION Unit QTY RATE

DSR (INR) NON-DSR (INR)

SITC of 43" 4k, UHD Commercial Display with 400 NITS, 24*7 ,Built in SOC/ Media Player

with Quad Core Processor 2.4 GHZ Wifi, CPU Built in With Cortex-A55*4, 1.1 GHz Processer,

Built in Google Certified Android 11 Operating System, 2.0GB, DDR3 2133Mhz and Memory

7 MR Flash 16GB EMMC, Inbuilt OTT App,With Built in Bluetooth, Wi-Fi/ LAN enabled, Audio Input Nos 2 55,750.00 111,500.00

& Audio Output, Built in Speaker(10W x 2), Built-in Chromecast , Basic Hotel Model Function

,HDMI Arc Function, Dolby Digital Audio, HDMI-CEC device linking supported, 2 USB(2.0) x 1

, USB 3.0 x 1, 3*HDMI(2.0 Side),HDR10/HLG, Headphone Out, 1 *RJ 45, SPDIF out and with

SITC of on Site Cubby

Cable Warranty

with flip top, cover and 6 Pass Through Holes for multi-format cables, 2

9 MR Universal Power Socket , 1 HDMI, 1 USB-C for Data Transfer, 2 Data/LAN/ Telephone etc., Nos 18 20,095.00 361,710.00

made of aluminium etc all complete in all respect

SITC of All in One Conference Unit, Camera Sensor 1/2.5″, CMOS, Effective Pixel: 8.0M, 4 x

MEMS mic array, AEC | ANS | AGC 180° Pickup Angle pickup Range: 5-8m (16-26ft) A.I.

camera with smart backlighting, auto-framing, speaker & presenter tracking, Inputs / Outputs

11 MR 1x USB-C Input with Alt-Mode, 1x HDMI Input, 1x HDMI Output etc all complete Nos 1 276,827.00 276,827.00

SITC of 4-Input 4K Wireless Presentation and Conferencing System with Matrix Outputs, USB

3.0, Multiview & Wireless Casting, Automatic or manual switching of 4 connected sources (2

HDMI & 2 USB-C) with assignable USB host connection, 60W PD on the USB C Ports,

Supports input resolutions up to 4K30 4:4:4 via USB-C or HDMI Inputs: 2x HDMI In: 19-pin

Type A, 2x USB-C, Wireless Video from Airplay or Miracast Source and casting dongle (1

dongle included), Outputs: 2x HDMI Out: 19-pin Type A, 1x Analog Audio Out, Video

Resolutions (Max): HDMI Out 1 – 3840x2160p @60Hz 4:4:4, HDMI Out 2 – 3840x2160p

@30Hz 4:4:4, USB: 3x USB 3.0 Type A device ports | 5v 10000mA per port, 2x USB 3.0 Type

SITC of Receiver for recieving HDMI 2.0 + RS-232 + bidirectional IR, over 10G copper network

cable. HDCP, 3D and 4K / UHD ( 60Hz RGB 4:4:4 , 60Hz YCbCr 4:4:4) compliant with HDR

15 MR support etc all complete Nos 2 245,899.00 491,798.00

S/I/T/C of Delegate Discussion Unit complete with gooseneck microphone - with its sleek and

compact form factor, D- Cerno SL guarantees zero mobile-phone interference and a

great digital sound quality. It is equipped with tactile buttons, braille indicators,

17 MR headphone connections and volume control and the cable connections are concealed Nos 18 37,750.56 679,510.08

for a neat overall look and feel.

SITC of Control Unit (CU) for AV Over IP product line Directly accessible SDVoE API, 3 RJ45-

type Ethernet connectors for flexible network configuration, Occupancy sensor connector Two

RS232 connectors for device control GPIO interface for device control etc all complete

1 Digitally signed by AMIT

SITC of 6.5-inch, 2-Way Ceiling Speaker, Rated Power: 30W, Frequency Range: 65 Hz – 20

kHz, Sensitivity: 88 dB, Rated Coverage 135° conical DMT, Maximum continuous SPL 106

dB, Nominal impedance: 8 / 16 Ohm, Transformer taps: 30W / 15W at 100 / 70V, IP-34 Rated,

21 MR Low-saturation and low-loss 70/100V transformers with 16Ω bypass, UL and CE Certified etc Nos 10 27,738.00 277,380.00

S/I/T/C of In-Ceiling Sub-Woofer with Backcan & Loopout having 1x 8 inch Driver; Frequency

Range: 42 Hz – 200 Hz; Nominal Coverage Angle: 180° Conical; Power handling capacity:200

Watts Continuous Program Power 100 Watts Continuous Pink Noise; Nominal Impedance :

22 MR 8Ω or 70/100V; Max SPL : 115 dB; Sensitivity : 95dB. ABS baffle with UL94 flame class fire Nos 2 26,432.00 52,864.00

rating; zinc-plated steel backcan.

S/I/T/C of Hand-Held Wireless Microphone Wireless Receiver: Switching bandwidth 30.5

MHz; Diversity System Microprocessor-controlled; Audio bandwidth 35 – 20 000 Hz (± 3 dB);

Signal to noise: 120 dB-A; RF diversity Antenna Receiver System; RF Band 3; RF Output

23 MR Power 50mW, RF Output: 10, 20 or 50mW, Audio Bandwidth: 40 – 20 000 Hz (+/- 3dB); inbuilt Nos 1 42,480.00 42,480.00

dual color display backlight. Handheld Transmitter: Dynamic Microphone capsules: super

cardiod; Switching bandwidth: 30.5 MHz; RF output power: 10 or 50 mW Modulation /

Bandwidth:Wideband FM; Max. SPL: 144 dB; SPL Audio bandwidth: 35 – 20 000 Hz; 1200

S/I/T/Cfrequencies that can

of Head-Worn be programmed

Wireless MicrophoneviaWireless

infrared within a 30Switching

Receiver: MHz wide bandwidth

MHz; Diversity System Microprocessor-controlled; Audio bandwidth 35 – 20 000 Hz (± 3 dB);

Signal to noise: 120 dB-A; RF diversity Antenna Receiver System; RF Band 3; RF Output

24 MR Power 50mW, RF Output: 10, 20 or 50mW, Audio Bandwidth: 40 – 20 000 Hz (+/- 3dB); inbuilt Nos 1 46,728.00 46,728.00

dual color display backlight. BodyPack Transmitter alongwith High-performance Headworn

Condenser Microphone: Pre-polarized condenser Cardioid microphone; Frequency Range: 80 -

20000 Hz; Max SPL: 120dB; Signal to Noise Ratio: 63 dBA.

SITC of Class D Dual Channel Mising Amplifier, 60 watts per channel into 4 and 8 ohms,

Bridged Mode Watts per channel: 200 W at 8 Ω & 4 Ω, 250 W at 70 V & 100 V, Signal to

Noise (A weighted, 20 Hz-20 kHz) >100 dB, Highpass Filter Switchable 80 Hz when Bridged

27 MR in 70V & 100V with minimum 3 microphone inputs etc all complete Nos 1 35,000.00 35,000.00

SITC of 4 Channel Class-D Amplifier, Power (per channels driven): 200 W at 8 Ω / 4 Ω / 100V

/ 70V, FlexAmp Technology, Frequency Response: 20 Hz – 20 kHz, Signal to Noise > 103 dB,

28 MR Input impedance >10k, balanced or unbalanced, User-configurable operating modes, UL, CE, Nos 1 25,000.00 25,000.00

RoHS/WEEE compliant etc all complete

SITC of 2 Meter Premium High Speed HDMI 2.0b Flexy Cable, Bandwidth up to 18Gbps, Up

to 4096x2160@60Hz at RGB 4:4:4 video resolution, High Dynamic Range (HDR10), Dolby

Vision and Hybrid log–gamma (HLG) video etc all complete

2 Digitally signed by AMIT

SITC of 15 Meter Active Copper HDMI Cable, Data Rate: Up to 18.2Gbps, Colour Depth: Up

to 16 bits, Colour Formats: RGB 4:4:4 / Y’CBCR 4:2:2 / Y’CBCR 4:2:0, Consumer Electronic

Control (CEC), Auto Lip-Sync Correction, Audio Return Channel (ARC), Enhanced Audio

33 MR Return Channel (eARC), High Dynamic Range (HDR) etc all complete Nos 18 20,653.00 371,754.00

SITC of 2 Meter USB Full-Featured Type-C cable for USB 3.1 Gen2, 4 Lane Displayport Alt

mode (4K60FPS Video and Audio), Supporting peripherals via USB 2.0 up to 480 Mbps

(Mouse, Keyboard, Thumb Drive, Speakerphone and Webcam) etc all complete

SITC of 15 Meter USB 3.1 Gen1 SuperSpeed Active Extension Cable TypeA/male to

TypeA/female, Supports 4K Webcam, SSD storage, Native USB2/USB1 and USB3 extension,

35 MR Plug and play compatible with PC, Mac, and Linux etc all complete Nos 9 37,054.00 333,486.00

SITC of 2 Conductor 16 AWG Speaker Cable, stranded Bare copper conductors, PVC/Nylon

36 MR insulation, PVC jacket (as per actual) etc all complete Metre 300 106.00 31,800.00

SITC of Category 6A Cable, 4 Pair, S/FTP, PVC jacket (as per actual) etc all complete

SITC of Various Cables, relay modules & Connectors etc all complete

SITC of 16U, Equipment Rack, with Front & Side doors, 4 No Fan Assembly, on Top of the

Rack, 4 Caster wheels, 2 no Shelfs to mount the equipments, 8X2, 5/6 Amp. Power

Distribution Unit as required , Cable Manager & Sufficient Rack hardwares etc all complete

3 Digitally signed by AMIT

SCHEDULE OF QUANTITIES: FIRE ALARM & PA SYSTEM

DSR NO AMOUNT (RS.)

S NO DESCRIPTION UNIT QTY RATE GST Factor Cess Factor

2022 DSR (INR) NON-DSR (INR)

Supplying, installation, testing and commissioning of

micro processor based intelligent addressable main fire alarm

panel, central processing unit with the following loop

modules and capable of supporting not less than 240

devices (including detectors) and minimum 120 detectors per

loop and loop length up to 2 km, network communication card,

minimum 320 character graphics/ LCD display with keypad and

minimum 4000 events history log in the non volatile memory

(EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs

1 17.2.1 back-up with 24 volt sealed maintenance free batteries with

automatic charger. The panel shall have facility to connect printer to

printout log and facility to have seamless integration with

analog/digital voice evacuation system (which is part of the

schedule of work under SH: PA System) and shall be complete

with all accessories . The panel shall be compatible for IBMS system

with open protocol BACnet/ Modbus over IP complete as per

Supplying, installation, testing & commissioning of intelligent

3 17.2.4 analog addressable photothermal detector with in-built isolator Each 100 2858.00 1.0633 0.973 2956.86 295686.08

complete with mounting base complete as required.

TOTAL (DSR + Non-DSR) 543186.09

1 Digitally signed by AMIT

SCHEDULE OF QUANTITIES: SIGNAGE

DSR/ AMOUNT (RS.)

S NO DESCRIPTION Unit QTY RATE

MR DSR (INR) NON-DSR

1 RECEPTION 3D ACRYLIC SIGNAGE

Providing, fabricating and fixing of 3D Brass Letters with backlit along

with the logo raised 1.5 inches of required size and shape with

MR arrangement of screws in the letters itself for mounting on the walls or Each 2 40,000.00 80000.00

pasting using 3M VHP Tape. Fixing complete as per directions of the

engineer. Tentative Size 42"x60" , as per approved drawings.

2 NAME SIGNAGE (All Floors)

Providing and fixing of Acrylic signage made of 3mm Acrylic with

textured wood finish pasted /White milky acrylic 3mm laser cut pasted

on top with proper names/ Departments written using plottercut vinyl or

MR laser cut acrylic letters in approved colour.Inserting provision for Each 50 2,500.00 125000.00

changing names .Fixing provision using 3M VHP double sided tape as

Signage Size 12x5 inch as per approved drawings.

3 FIRE EVACUATION MAP / SIGN.

Providing and fixing of Clear Acrylic sandwich frame of 3mm & 2mm

acrylic with Evacuation Plan Printed on photoluminescent media and

inserted between the two frames. Should be fixed on the wall using 4

MR Screw/ SS studs. Size 12 inch x 17 inch as per approved drawings. Each 4 3,000.00 12000.00

4 FIRE ESCAPE EDGE-LIT SIGNAGE

Providing and fixing of Edge-Lit signage with battery backup. Made

from acrylic sheet of 8 mm thickness laser engraved, Transformer to

be inbuilt. Maintenance - free sealed nickel cadmium battery included •

120V/277V AC Operation • Crystal clear acrylic face panel• Engraved

MR letters increase visibility • Anodized aluminum faceplate • Field applied Each 2 3,500.00 7000.00

chevron directional indicators simplify installation • Long life, energy-

saving LED lamps • Dual-voltage 120V/277V AC Operation • UL listed.

To be installed at stairs entry. Size 310mm x 175mm as per approved

5 FIRE SAFETY SIGNAGE

1 Digitally signed by AMIT

Providing fabricating and fixing of signage 05 mm thick Acrylic / Sun

board sheet at base with photoluminescent film self adhesive & colored

vinyl ( Red/Green) Plotter cut and pasted on top. Both side / Single

MR Side facing Complete including fixing on wall with screws and washers

or hanging on ceiling with GI chain/GI Bar complete as per technical

specifications and directions of Engineer. as per approved drawings.

Photoluminescent signages

TOTAL 225600.00

2 Digitally signed by AMIT

SCHEDULE OF WORKS FOR MODULAR FURNITURE Date : 06-12-2025

S. NO. SPECIFICATION UNIT 3rd Floor 2nd Floor UNIT RATE 3rd Floor AMOUNT 2nd floor Amount INDICATIVE IMAGE

Manufacturing, providing and placing in position machine made factory assembled workstation of following dimensions with the following specifications.

Providing and placing Hybrid Panel based Workstations with following specifications:Frame Work, Partition and Cable management : Frame work shall consist of main spine

and return spine of aluminium extruded section of minimum thickness of 1.2 mm. The overall thinkness of Panel base System should be minimum 60-70 mm.The thickness

of main spine partition panel should be minimum 60-70 mm and & Return spine partition panel should be minimum 25-30 mm. The panel will be hollow inside to

accommodate wiring for electrical/data and outer frame of panel should be made of extruded aluminium.The panel shall be made up of 3 mm thick MDF both sides of the

wooden frame to create the hollow for the wire management. The panel outer aluminium frame is designed in such a way that it can be easily slide in to the columns/

Connectors by means of stacking one over the other. Horizontal race way should be 150-170 mm height aluminium profile. There shall be complete cable management

arrangement with openable raceway above/ below worktop with provision for fitting electrical/data switches and holes for passing cable.Panel Finishes : Finishes of panel

above the worktop can be fabric pinup/fabric/laminate + Glass/metal writable marker board or single finish tile with raceway on main spine. Finishes of main spine panel

below the worktop the hollow panel should be made of MDF tile and 0.5mm thick steel sheet pasted on MDF which is powder coated with EPC finish 80-90 microns for -

durability on the inside as well on the outside. Raceway can be provided above/below the worktop.Connectors/ Brackets: End Post: Aluminium 60-70 mm width – 1180-

1220 mm height.Two way post: Aluminium 30-70 mm width –1180-1220 mm height.

Three way post: Aluminium 30-70 mm width –1180-1220 mm height.

Four way post: Aluminium 30-70 mm width – 1180-1220 mm height.

Brackets: Table top supported with 50-60mm width steel bracket.

Table top to table top connector: 150-170 mm Width x 120-140 mm Depth width connector.

Worktop :Worktop Made of 25mm thick E-1 grade particle board finished with 2mm ABS edge banding. E1 grade laminate with zero urea formaldehyde emissions (<or=

8mg/100 g oven dry board-perforated method) for better in-house air quality. This should comply with (EN 120-1992). The exposed edge of worktop shall be secured with

2mm thick PVC edge banding tape of approved colour. The height of Worktop shall be 740-760 mm from ground level. The particle board should be E-1 Grade with pvc

edge banding. Drawer Unit : 3 drawer Metal pedestal of overall dimensions internal and external dimensions 400 mm (W) x 450 mm (D) x 600 mm ( H). Drawer body should

be made of CRCA of thickness 0.7-0.8 mm duly powder coated with 70-80 micron. Each pedestal should be provided with pencil tray of 40-45 mm(H) x 110-120 mm (D) x

300-310 mm (W).Each pedestal should have 5 Nos castor fitted to it where in one castor will be fitted to lower most drawer to provide extra stability. Product should be

BIFMA gold rated SCSglobal certified for inhouse air quality.

1 Rectangular Workstation of size:- 1350mm (W) x 750mm (D) x 740mm(Worktop Height) x 1190 mm Nos. 15 47650.00 - 714,750.00

76 Supplying, fixing, placing in position and functional working Cubical Cabin Table AND 1200HT PARTITIONS

MAIN TABLE: 1500W X 750D X 750HT TABLE TOP

SIDE COMP STORAGE 2D1F: 900 X 450 X 750HT

Table top : Made of 25mm thick MDF As per IS 12406:2021, BIS certification board of approved shade . All the edges of cabin table surface shall be provided with machine

pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC.

2 Main Frame : Height - 1200mm frame with top and sides in Aluminium trims and junctions with Nos. 5 44,350.00 221,750.00

diecast caps. Partition is made of 50mm MINIMUM thick 1200mm ht NEO based system with fabric above and lamiante below the table top.Fabric magnetic and glass

markers are provided for each workstation.

Support : Table top is supported on MS Powder coated Square single perform Legs which is

constructed by 50Sq-16g ERW tube

Wire Management : Raceways are provided BTT only main spine and skirting on main (inside)

spine for power and data cable management. 65mm dia grommet hole is provided for wire access.

77 Supplying, fixing, placing in position and functional working Cabin Main Table - 1500W X 750D X 750HT

SIDE COMPOSITE STORAGE - 900 X 450 X 750HT

Table top: Made of 25mm thick MDF As per IS 12406:2021, BIS certification board of approved shade . All the edges of cabin table surface shall be provided with machine

pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC.

Under Structure Support: Table top is supported on MS Powder coated Square perform Legs which

is constructed by 50Sq-16g ERW tube acts as vertical member & supporting ms cross beam, which is

made of 40 x 20 16 gauge rectangular tube and connected to legs with aluminium die cast wing

connectors. Modesty Panel: MS square perforated metal modesty panels of 450mm ht are provided at passage side only.

Wire Management. 450mm Anodised flip up Made of Aluminum in anodised finish, which has soft

3 closure and three way wire acess & PVC cable dump. Vertebra for wire entry. Nos 39 18000 702,000.00 702,000.00

Side Composite Storage: Storage is made of 25mm thick top, 18mm MDF As per IS 12406:2021, BIS certification with openable shutters,adjustable shelves, auto closing

hinges, locking mechanism, finger groove handles and 2D+1F Drawer unit with Regular locking system.

PARTITIONS :- Panel based partition of 60mm thickness with framework made of aluminium alloy extrusions. All Aluminium parts are duly finished with powder coating in

desired shade/colour. Powder coating shall be 40-60microns thickness and shall be pretreated for seven stage anti-corrosion treatment followed by epoxy powder coating.

All these frame work sections are fitted to each other by fasteners 2 mm thickness which is properly zinc coated for corrosion resistant.

Vertical Member in aluminum alloy extrusion of size 60x26mm having thickness of 1.2mm duly epoxy polyester powder coated.Horizontal Member in aluminum alloy

extrusion of size 60x30mm having thickness of 1.2mm duly epoxy polyester powder coated. Middle Member in aluminum alloy extrusion of size 60x30mm having thickness

of 1.2mm duly epoxy polyester powder coated. Having provision to support the worktop with engineered design Support bracket.

Bottom Raceway/Skirting in aluminum alloy extrusion of size 100mm ht. having thickness of 1.5mm duly epoxy polyester powder coated.

Top & End Trims -The exposed vertical and horizontal faces of the frames are snap fitted with trims. The trims are made of aluminum extrusions of size 60x19mm of

thickness 1.5mm and are covered with ABS or Die cast caps

Manufacturing, providing and placing in position machine made factory assembled Interrogation Cabin Table of following dimensions with the following

specifications.

Digitally signed by AMIT

S. NO. SPECIFICATION UNIT 3rd Floor 2nd Floor UNIT RATE 3rd Floor AMOUNT 2nd floor Amount INDICATIVE IMAGE

Providing & Placing of Cabin office Table with side table with following details and specifications :

Top and legs are made of 25mm E-1 grade particle board finished with 2mm PVC edge banding. E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g

oven dry board-perforated method) for better in-house air quality. This should comply with (EN 120-1992). The exposed edge of worktop shall be secured with 2mm thick

PVC edge banding. The 18mm Thick Modesty panel is made of E-1 grade particle board finished with 2mm PVC edge banding. E1 grade laminate with zero urea

formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house air quality. This should comply with (EN 120-1992). The exposed edge of

worktop shall be secured with 2mm thick PVC edge banding. Wire management: Completely concealed wiremanagement with Aluminium anodized flipper with soft closure,

wiring tray & Housing made from MS sheet 1.2 mm., flange structure epoxy powder 70-80 micron coated spray color, baked at temperature 200c with vertical wire uptake

from floor via Fexibale cable riser/ Metal Powder pole .Side table top & Legs are madeout of 25 mm thick E-1 grade particle board finished with 2mm PVC edge banding. E1

grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house air quality. This should comply with (EN 120- -

1992). Side Table having the top supported three drawer melamine pedestal (1B+1B+1F) with I Type Handle & cetral lock. 3 drawer melamine finish pedestal of overall

dimensions internal and external dimensions 400mm (W) x 430 mm (D) x 690 mm ( H). Drawer should be made of 18mm thick E1 Grade particle board with matching edge

banding. Each pedestal should One castor to be fitted to lower most drawer to provide extra stability. E1 Grade laminate to be used which provide no urea formaldehyde

emission and formaldehyde should be phenol base with emission of not more than (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This

should comply with (EN 120-1892).Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty.

4.1 Cabin Table, Main Table 1950W x 750D x 740Hmm, Return Table :1050W x 450D x740-760Hmm Nos. 9 9 97,450.00 877,050.00 877,050.00

Manufacturing, providing and placing in position machine made factory assembled Cabin Table of following dimensions with the following specifications.

Providing & Placing Table with side unit with following details and specifications : Top is made of 50-55 mm thick ( 25+3+25mm) particle board with 3 mm thick MDF board

between the two particle baord with approved 0.4 mm thick veneer laminate and PU polish accordingly (Environmental Friendly) top profile should be in rectangle shape with

matching edges . Rectangular shaped table with 18mm thk modesty panel with matching finish. Top is Supported both C type side leg (50-55mmmthk ) , onse side leg

having the three equal drawer pedesatl with profile handle. , drawer unit are made out of 18 mm thick particle board stalled where switch socket are fitted (2-3 nos switch

socket) and closed wiring tray made of M.S. thickness 1.2mm, Epoxy powder coated spray color, baked at temperature 200 C°. Table table with combo Storage: It is

provided with the combination of 2nos Swing door & one nos drawer & open space fro CPU & Key board tray. The top of the Storage is 25mm thick and Body of storages is

made out of 18 mm thick particle board should be provided with lockable castor/ wheels. The Swing door & drawer should be operated with profile handle and easily close &

open with the assistance of sliding channels/ Hinges . Drawer facia, sides and all other should be made in 18 mm thick and drawer base should be 18 mm thick. The

complete structure should be supplied with approved veneer laminate, PU polish and deco painted..Full Height Back Storage: Full height back storages is made out 18

mm particle board with approved 0.4 mm thick veneer laminate and PU polish accordingly (Environmental Friendly). Back Storage is combination of Wooden & Open space

. All shelves are adjustable. The storage should have be operated with profile handle and easily close & open with the assistance of sliding channels/ Hinges. Door Lock

should be of three-way lock mechanism, the hinged doors can be locked at once. Door should be provided with Hinge-damping mechanism to enable soft closing of doors.

Storages should be provided Skirting with adjustable levelers.Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty.

5.1 Cabin Table is of Size: 3300mm(L1) x 2400mm(L2) x 1200(D1) x 650mm(D2)x 740-760mm(H1) Nos. 1 535,450.00 535,450.00 -

Supplying, fixing, placing in position and functional working Cafeteria Table

1. Dimensions: 1500mm (L) x 900mm (D) x 750mm (H)

2. The tabletop should be 25mm thick BWR (Boiling Water Resistant) plywood, ensuring durability and resistance to moisture. The surface will be finished with a 1.2mm

laminate, providing a sleek and easy-to-clean finish.

All edges will be fitted with PVC edging for durability and aesthetic appeal.

6.0 Support Structure: The tabletop will be supported by two (2) mild steel C-shaped legs, each measuring 50mm x 50mm. Nos 2 12600 25,200.00

The legs will be connected by horizontal connectors for stability.

All metal components will be treated with a powder coating of 50 microns to enhance protection against corrosion and wear.

The finish, colour, design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

CONFERENCE TABLE: Supplying, fixing, placing in position and functional working unitzed 10 seater Conference Table.Work Surface: Made MDF As per IS 12406:2021,

BIS certification/ Plywood of finished thickness of 36 mm, one side prelaminate board conforming to IS14587: 1998 and having chamfered edge. Full length access panel is

provided with soft closing hinges in line with worktop edge.

Understructure: The understructure consists of mixture of 18mm and 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-

12823:1990, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. Modesty: Made of 18mm Thick

Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.

7.0 Wire Management: An array of panels made of 0.8mm and 1.2 mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and Nos 1 28505 28,505.00

cables. Cutout for 4 module is provided for electrical fittings in Straight two seater and single seater modules below access flap per seat.Overall dimension in mm

(2100x1150x740) (WxDxH). The finish, design and size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

Manufacturing, providing and placing in position machine made factory assembled Meeting Rooms Table following dimensions with the following specifications.

CONFERENCE TABLE: Supplying fitting & fixing conference table 50 seater

1. Dimensions: 13755mm (L) x 2795mm (B) x 750mm (H)

2. Construction:Tabletop: The tabletop will be made from 36mm thick pre-laminated MDF As per IS 12406:2021, BIS certification (Medium Density Fiberboard),

The surface will be finished with a 1.2mm thick laminate in an approved shade.Side Panels: The conference tabletop will be supported by 25mm thick side panels made of - -

MDF As per IS 12406:2021, BIS certification, finished in a brown-black oak color with a 1.2mm thick laminate in an approved shade.Modesty Panel: Below the tabletop, an

18mm thick pre-laminated MDF As per IS 12406:2021, BIS certification modesty panel will be installed, ensuring a clean and polished appearance.Edge Treatment: All

exposed edges of the work surface will be finished with 2mm thick edge binding tape in a matching color, secured with hot melt glue for a seamless finish.

3. Wire Management: The table will feature a 6-module flip-top box (without switch-socket) mounted above the tabletop.

8.1 U Shape Confernce Table: 71. Dimensions: 13755mm (L) x 2795mm (B) x 750mm (H) Nos. 1 251,000.00 251,000.00

Digitally signed by AMIT

S. NO. SPECIFICATION UNIT 3rd Floor 2nd Floor UNIT RATE 3rd Floor AMOUNT 2nd floor Amount INDICATIVE IMAGE

Manufacturing, providing and Placing High Back revolving chairs for Cabin Main Chair of make of following dimensions with the following specifications.

Chair should be high back, cushioned seat assembly, moulded plywood upholstered with moulded polyurethane foam & finished with Leatherite. Back size: (W) 450 - 500

mm (H) 600-620mm; Seat size: (L) 450mm - 500mm (W) 450 - 500mm with Polyurethane Foam. Polyurethane Foam: The polyurethane foam (Recyclable) of minimum

density = 30 kg/ cum + 2 kg/cum fixed to moulded plywood and upholstered with Leathrite. Fixed armrest of premium quality of SS Chromed finish with PU cushion pads.

Synchro mechanism: 360 degree revolving type, from pivot for tilt with multiple locking position & feet resting on ground for extra comfort. The pneumatic adjustment has an

adjustment stroke of 70-120 mm, Pedestal Assembly: should have 5 star aluminium die cast with hard castors sutable for tiles flooring with adjustment, twin wheel castors &

the pitch centre Dia is 650 +/- 50mm. (750 +/- 10mm with castors). Twin wheel castors: these are made of injection moulded in black PP having 50-60mm dia,complete in all

respect. The above chair should be finished / completed as per above mentioned specifications including providing and fixing of other related materials including hardwares, Nos. 2 55,000.00 110,000.00 -

etc. complete or as directed by the Engineer-in-Charge and conforming to the image having back curvature in longitudinal and in trasverse direction as per the image. All

complete as per manufacturers specification.

Manufacturing, providing and Placing High Back revolving chairs for Asst./ Deputy Main Chair of make of following dimensions with the following

specifications.

Providing and placing in position high back Revolving Chair with Adjustable headrest , Overall Chair size: 430-460W x 440-470Dx 1260-1360Hmm, BACKREST: The outer

frame of the backrest made of injection moulded in black 20% Glass Filled Polypropylene and inner frame made up of injection moulded in black polypropylene. Inner frame

upholstered with mesh fabric then assembled with outer frame. The back has fix lumber support for achieving comfortable seating posture. Lumber support size 280 mm (W)

x 110 mm (H). Backrest size 780-810 mm (H) x 460-480 mm (W). Spine made of reengineered black nylon. Backrest is tested for Static testing- 67kg (Functional Load) &

102 Kg (proof Loading) for 1 Min and cyclic testing- 57 Kg Loading for 1,20,000 cycles and will comply to ANSI/BIFMA X 5.1 standards. SEAT:The seat is made up of 12 mm

thick (7 layers) hot pressed plywood and moulded seat foam upholstered with fabric. The bottom cover made up of injection moulded in black PP to cover the plywood. Seat

size 460-480 mm(W) x 440-470 mm (D). Minimum and Maximum seating height is 480 mm and 580 mm respectively.Seat Foam: Foam made out of moulded polyurethane

foam with the following properties. Average thickness of 55-65 mm with the following properties: Density: 52-55 Kg/M³ , Hardness: 25±/3 KGF ,Compression Set: 10% Max

,Tensile Strength: 0.90 to 1.2 Kg/Cm² ,Resilience: 40%-60% ,Comfort / Indentation Hardness: 15.4 ,Weight: 650 gms, ARM REST & HANDLES: ADJUSTABLE ARMS:The

armrest is made up of Thermo Polyurethane with 40 - 55 Shore Hardness and reinforced with 4 mm thick nylon insert. Arm pad size 235 mm (L) x 80 mm (W). The handle is

fitted to the seat with seat/handle connecting strip assembly made of 35% Glass filled nylon 20 mm thick. Adjustable arm rest with height adjustment up to 70 mm. Minimum Nos. 7 9 25,750.00 180,250.00 231,750.00

and Maximum height of armrest is 265 mm / 335 mm respectively. The front and back movement of armrest is 60 mm. The Handle is tested for Static Testing-75 Kg loading

for 1 min (Functional Load) and 103 Kg for 15 secs (Proof Load) and cyclic testing- 41kgs for 60,000 cycles and will comply as per ANSI/BIFMA X 5.1. standards.

Mechanism, single point control for seat and back adjustment, front pivot for tilt, tilt adjustment for back in 3position locking with antishock feature.Conventional mechanism

with one lever control for lock and seat height adjustment. Mechanism made out of MS plate thickness is 3 mm and seat’s tilting angle is 3° - 10° and back tilting angle is 87° -

106°. Also, it has the back tension adjustment knob. The mechanism has a knob to adjust the back tilt tension and is tested for 300000 cycles as per ANSI/BIFMA X 5.1.

Following are the approved mechanism options to use with the chair. pneumatic height adjustment of 8.5 cm spine bracket made of aluminum die cast piece connecting to

back with mechanism, Base: pedestal made of die cast alunimium fitted with 5 nos. twin wheel castors (castor wheel dia. 60 mm approx.), base pedestal dia 60-70 mm and

pitch center dia. 660-680mm with castors, twin wheel castors injection moulded in Nylon etc. all complete as per direction of Engineer-in-Charge.The base is tested for static

load of 1200 kg. Castors:.60 mm: The twin wheel castors are injection moulded in nylon 35% Glass Filled and diameter of castor is 60mm. The castors are tested for 100000

cycles and will comply as per ANSI/BIFMA X 5.1 standards. Fabric properties: Content : 100% Polyester,Abrasion : 80,000,Flammability : Adheres to BS EN 1021-1 1994

(Cigarette),: Adheres to BS 7176:1995 (Low Hazard) Color Fastness to,Light Adhere to : 5+ [BS 1006 (1990)],Rubbing: Adhere to Dry: Class 5,Adheres to Wet: Class 4.5,

Manufacturing, providing and Placing visitor for Asst./ Deputy Mid back visitor Chair of make M/s (as per finally approved sample by department) of

10.0 following dimensions with the following specifications. -

Providing and placing in position medium back Revolving Chair , Overall Chair size: 430-460W x 440-470Dx 1060-1160Hmm, BACKREST: The outer frame of the backrest

made of injection moulded in black 20% Glass Filled Polypropylene and inner frame made up of injection moulded in black polypropylene. Inner frame upholstered with mesh

fabric then assembled with outer frame. The back has fix lumber support for achieving comfortable seating posture. Lumber support size 280 mm (W) x 110 mm (H).

Backrest size 780-810 mm (H) x 460-480 mm (W). Spine made of reengineered black nylon. Backrest is tested for Static testing- 67kg (Functional Load) & 102 Kg (proof

Loading) for 1 Min and cyclic testing- 57 Kg Loading for 1,20,000 cycles and will comply to ANSI/BIFMA X 5.1 standards. SEAT:The seat is made up of 12 mm thick (7

layers) hot pressed plywood and moulded seat foam upholstered with fabric. The bottom cover made up of injection moulded in black PP to cover the plywood. Seat size 460-

480 mm(W) x 440-470 mm (D). Minimum and Maximum seating height is 480 mm and 580 mm respectively.Seat Foam: Foam made out of moulded polyurethane foam with

the following properties. Average thickness of 55-65 mm with the following properties: Density: 52-55 Kg/M³ , Hardness: 25±/3 KGF ,Compression Set: 10% Max ,Tensile

Strength: 0.90 to 1.2 Kg/Cm² ,Resilience: 40%-60% ,Comfort / Indentation Hardness: 15.4 ,Weight: 650 gms, ARM REST & HANDLES: ADJUSTABLE ARMS:The armrest is

made up of Thermo Polyurethane with 40 - 55 Shore Hardness and reinforced with 4 mm thick nylon insert. Arm pad size 235 mm (L) x 80 mm (W). The handle is fitted to

the seat with seat/handle connecting strip assembly made of 35% Glass filled nylon 20 mm thick. Adjustable arm rest with height adjustment up to 70 mm. Minimum and Nos. 31 55 23,000.00 713,000.00 1,265,000.00

Maximum height of armrest is 265 mm / 335 mm respectively. The front and back movement of armrest is 60 mm. The Handle is tested for Static Testing-75 Kg loading for 1

min (Functional Load) and 103 Kg for 15 secs (Proof Load) and cyclic testing- 41kgs for 60,000 cycles and will comply as per ANSI/BIFMA X 5.1. standards. Mechanism,

single point control for seat and back adjustment, front pivot for tilt, tilt adjustment for back in 3position locking with antishock feature.Conventional mechanism with one lever

control for lock and seat height adjustment. Mechanism made out of MS plate thickness is 3 mm and seat’s tilting angle is 3° - 10° and back tilting angle is 87° - 106°. Also, it

has the back tension adjustment knob. The mechanism has a knob to adjust the back tilt tension and is tested for 300000 cycles as per ANSI/BIFMA X 5.1. Following are the

approved mechanism options to use with the chair. pneumatic height adjustment of 8.5 cm spine bracket made of aluminum die cast piece connecting to back with

mechanism, Base : Pedestal made of nylon base fitted with 5 nos. twin wheel castors (castor wheel dia. 60mm), base pedestal dia 60-70 mm and pitch center dia. 660-

680mm with castors, twin wheel castors injection moulded in Nylon etc. all complete as per direction of Engineer-in-Charge. Nylon Base: The base is injection moulded in

black 35% glass filled nylon and fitted with 5nos. The base is tested for static load of 1200 kg. Castors:.60 mm: The twin wheel castors are injection moulded in nylon 35%

Glass Filled and diameter of castor is 60 mm. The castors are tested for 100000 cycles and will comply as per ANSI/BIFMA X 5.1 standards. Fabric properties: Content :

100% Polyester,Abrasion : 80,000,Flammability : Adheres to BS EN 1021-1 1994 (Cigarette),: Adheres to BS 7176:1995 (Low Hazard) Color Fastness to,Light Adhere to : 5+

Digitally signed by AMIT

S. NO. SPECIFICATION UNIT 3rd Floor 2nd Floor UNIT RATE 3rd Floor AMOUNT 2nd floor Amount INDICATIVE IMAGE

Supplying, fixing, placing in position and functional working fix cantilever chair,

All over size is : 610mm(L)x 505mm(D)x 990mm(H) ,The chair made of full leatherette in black colour.

Details : - Arms : chrome finish arms with pu padding .

Use of ply: 12 mm minimum thick hot pressed BWR plywood (IS Grade - 303 for seat and back) .Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu

meter for best quality cushioning in seat ,

Back : 40 ± 2 mm thick polyurethane foam with density 45 (±3) kg per cu meter for best quality cushioning in back . backrest support foam , sign based on symmetrical

lumbar support backrest support . Only seat size is 610mm(L)x 505mm(D)x 485mm(H) & the back size is 610mm(L)x 540mm(H) , Base : chrome finish tublar frame of

cantilever type .

The finish, colour, design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

Manufacturing, providing and Placing Mid Back revolving chairs for Workststion & cabin-3 Visitor Back of make M/s (as per finally approved sample by

12.0 department) of following dimensions with the following specifications. - -

Providing and placing in position medium back Revolving Chair, Overall Chair size: 460-480W x 455-480Dx 1000-1100Hmm ,Backrest :The outer frame of the backrest

made of injection moulded in black 20% Glass Filled Polypropylene and inner frame made up of injection moulded in black polypropylene. Inner frame upholstered with mesh

fabric then assembled with outer frame. The back has fix lumber support for achieving comfortable seating posture. Lumber support made up of injection moulded in black

P.P. Lumber support size 280 mm (W) x 140 mm (H). Backrest size 570-590 mm (H) x 490-510mm (W). Spine made of reengineered black nylon. Seat : The seat is made

up of 12 mm thick (7 layers) hot pressed plywood and moulded seat foam upholstered with fabric. The bottom cover made up of injection moulded in black PP to cover the

plywood. Seat size 455-470mm(W) x 450-470 mm (D). Seating height is min.440mm and maxi. 540 mm respectively. Seat Foam: Foam made out of moulded polyurethane

foam with the following properties. Average thickness of 55-65 mm with the following properties: Density: 45 Kg/M³ or more , Hardness: 25±/3 KGF ,Compression Set: 10% Nos. 30 13,500.00 405,000.00

Max ,Tensile Strength: 0.90 to 1.2 Kg/Cm² ,Resilience: 40%-60% ,Comfort / Indentation Hardness: 15.4 ,Weight: 650 gms ,Adjustable Armrest: Adjustable Handle : The

armrest is made up of Thermo Polyurethane with 40 - 55 Shore Hardness and reinforced with 4 mm thick nylon insert. Arm pad size 235 mm (L) x 80 mm (W). The handle is

fitted to the seat with seat/handle connecting strip assembly made of 35% Glass filled nylon 20 mm thick. Adjustable arm rest with height adjustment up to 70 mm. Minimum

and Maximum height of armrest is 255 mm / 325 mm respectively. Arm Distance outside 640-650mm, Arm Distance inside 465-490mm .The front and back movement of

armrest is 60 mm. Mechanism: single point control for seat and back adjustment, front pivot for tilt, tilt adjustment for back in 3position locking with antishock feature:

Conventional mechanism with one lever control for lock and seat height adjustment. Mechanism made out of MS plate thickness is 3 mm and seat’s tilting angle is 3°-10°

and back tilting

Supplying, angle

fixing, is 87°-106°.

in position anditfunctional

has the back tension

working adjustment

visitor knob. The

chair. 1. SEAT mechanism

ASSEMBLY: Thehas a assembly

seat knob to adjust the back

is made up of tilt

±0.1cm.Following are the approved

thick hot-pressed plywood ,

upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE : 47.0 cm. (W) x 48.0 cm. (D) 2.

BACK ASSEMBLY: The back asembly is made of Base : chrome finish tublar frame of cantilever type . The back is upholstered using Net fabric with high tenacity yarn. 3.

HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =45+/-2 kg/m³ and hardness load 16 ± 2 kgf as per IS:7888 for 25%

compression. 4. ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. 6. TUBULAR FRAME (FOR 7512RG): The powder

13.0 coated (DFT 40-60 microns) tubular frame is cantilever type & made of Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. WIDTH (W): 61.0 CM. DEPTH (D): 64.5 CM. Nos. 58 77 4881 283,098.00 375,837.00

HEIGHT (H): 93.5 см. SEAT HEIGHT (SH): 46.5 CM.

The finish, colour, design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

Manufacturing, providing and placing in position machine made factory assembled Sofas for JS Cabins of make M/s s (as per finally approved sample by

14.0 department) of following dimensions with the following specifications. - -

Providing & Placing sofa, with wooden structure fabricated using hardwood of approved quality, duly seasoned and anti-termite treated with approved chemical and

methodology.The wooden base frame of the sofa shall be provided with M.S. helical spring along with high quality elastic belt 70-80mm, sides & back with 40-60mm elastic

belt, seat & back covered with jute & foam covered with Polyfilla & finished with thick marking cloth before doing final finish with leatherette material The component

specification shall be as follows Seat- 40-45Kg/cum density PU Foam, 100mm thick, Back– 32 - 40Kg/cum density PU foam, 50mm thick, Sides (inside)- 32-40 Kg/cum

density PUFoam, 11mm thick Sides (outside) &back (back side) - 35-40 Kg cum density PU foam, 13mm thick. Seat shell rest on Wooden Legs supported solid

wooden section of height 50-180mm. All Wooden work should be in White Ash / Teak wood polish with melamine & p.u coat Base of sofa should be infilled with suitable

wooden sections so as to give proper support to the seat Height of the base of sofa. sofa shall be 75-220mm (Approx). Finished width of arm shall be 100 - 180mm (Approx)

after upholstery work. Sofa to be fully upholstered using leatherette material of approved quality and shade , duly embossed including providing & fixing of all other required - -

materials and hardware etc. all complete as directed by the Engineer in charge. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05

years warranty.

14.1 3 seater sofa overall dimension - 1950mm W x 760-780mm D x 680-700mm H Nos. 1 63,450.00 63,450.00 -

14.2 1 seater sofa overall dimension - 810mm W x 760-780mm D x 680-700mm H Nos. 3 32,000.00 96,000.00 -

Supplying, fixing, placing in position and functional working 3 seater size : 2125mm(l) x960mm(d)x 820mm(h). Material : premium leatherette /style : with kiln-dried wood

framing makes it warp and scratch resistant,the panelled back and cushioned armrests Combination construction structure are made in moisture content shall be less than

(10-12)%. thickness of plywood used (mm) shall be 12 mm grade is 303 indian standard for commercial (common) and moisture proof plywood (tentative).understructure

frame shall be constructed from 18 mm thick kiln-dried beech wood. the complete structure shall be covered by p.u.foam fixed with adhesive glue ,the frame shall be padded

with high resilience polyurethane foam having 45 +/- 5 density in seat it shall be stack foam of 50mm thik,32mm thick back foam having 45 +/- 5 density foam used ,there

shall be cushion arm 25mm thick provided padded with high resilience polyurethane foam having density 45 +/- 5. the complete stack foam structure shall be covered it

complements the modish legs are made by square shape in solid wood material. ( seat : 480 mm(d) x 475mm(h) , arms height @ 685mm / back height @ 460mm ).

The finish, colour, design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

Digitally signed by AMIT

S. NO. SPECIFICATION UNIT 3rd Floor 2nd Floor UNIT RATE 3rd Floor AMOUNT 2nd floor Amount INDICATIVE IMAGE

Supplying, fixing, placing in position and functional working 1 seater sofa size : 1140mm(l) x960mm(d)x 820mm(h). Material : premium leatherette /style : 3 seater exclusive

premium leatherette lounge seating sofa with kiln-dried wood framing makes it warp and scratch resistant,comfortable seat depth & height designed wrapped in buttery-soft

premium leatherette with panelled back and cushioned armrests.

Combination construction structure are made in moisture content shall be less than (10-12)%. thickness of plywood used (mm) shall be 12MM grade is 303 indian standard

for commercial (common) and moisture proof plywood (tentative).understructure frame shall be constructed from 18 mm thick kiln-dried german beech wood framing is highly

16.0 durable. the complete structure shall be covered by p.u.foam fixed with adhesive glue ,the frame shall be padded with high resilience polyurethane foam having 24 +/- 5 Nos. 4 18000 72,000.00

density in seat it shall be stack foam of 50mm thik,32mm thick back foam having 45 +/- 5 density foam used ,there shall be cushion arm 25mm thick provided padded with

high resilience polyurethane foam having density 45 +/- 5. the complete stack foam structure shall be covered with premium leatherette , it complements the modish legs are

made by square shape in solid wood material. ( seat : 480 mm(d) x 475mm(h) , arms height @ 685mm / back height @ 460mm ).

The finish, colour, design & size of the furniture is tentative and could vary +_ 5% and to be approved by engineer in charge.

Manufacturing, providing and Placing Center & Corner table of make M/s (as per finally approved sample by department) of following dimensions with the

17.0 following specifications. - -

Providing and fixing tables of Centre table Size - 900mm W x 600mm D x 365mm H for whose top & Base are made of Particle board wood Grade E-1(Environmental

Friendly), thickness 19mm cover with Melamine, Edge banding (PVC) 2mm.E1 grade laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-

17.1 perforated method) for better in-house quality. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty Nos. 6 9 13,500.00 81,000.00 121,500.00

BEDSIDE UNIT: Supplying, fixing, placing in position and functional working bed side table.Overall Size : 400mmW x 450mmDX500H. Material : Body and drawer panels of

Bed side table are made of 18 mm thick MDF As per IS 12406:2021, BIS certification Board with 1mm thick laminated, all the exposed edges are edge banded with 0.8 mm

thick PVC edge banding. Side panels are made of 18 mm thick MDF As per IS 12406:2021, BIS certification board with imported H.D.F. foil wrapped decorative trim fixed on

18.0 to it. Hardware : The high quality hardware (with 5 years warrenty ) soft touch/hydraulic used like Roller slides, Hinges , minifix, dowels is of make approved make. 18 mm Nos 2 5489 10,978.00

thick MDF As per IS 12406:2021, BIS certification Board is in shade matching to bed. The finish, colour, design & size of the furniture is tentative and could vary +_ 5% and

to be approved by engineer in charge.

Manufacturing, providing and placing in position machine made factory assembled Reading Table of make M/s Platform Series (as per finally approved sample

19.0 by department) of following dimensions with the following specifications. -

Providing & Placing reading Table with following details and specifications : 750Wx 750D x740Hmm

Top is made of 25mm thick E-1 grade prelaminated particle board finished with 2mm thick PVC lipping. Grains of the table top to be unidirectional. The height of Worktop

shall be 740-760 mm from ground level. Understructure: MS legs SQ leg , where Structure made from cold rolled steel,thickness 1.2 mm. Epoxy powder coated spray paint,

19.1 baked at temperature 200 C° coated of 80-90 micron thickness. Powder coating should be scratch resistance (cross hatch test 6x6 grid method), well supported with beams Nos. 2 24,500.00 49,000.00

under table top.Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty.

Providing & Placing of Full Height Storage with Coat hanger. 900Wx 550Dx 2000Hmm Shelves & drawer, Body of storages made out 18 mm thick Particle Board (E-1

Grade), melamine finishes with 2 mm PVC edge-banding. E1 grade laminate to be used which provide no urea formaldehyde emission and formaldehyde should be phenol

base with emission of not more than (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992). Front of

Medium height Storages should be made out of 16 mm thick Particle Board (E-1 Grade) melamine finishes with 2 mm PVC edge-banding fitted with extruded aluminum

handle, as per requirement. Top should be 25 mm thick Particle Board (E-1 Grade), melamine finishes with 2 mm PVC edge-banding. Storages should be provided with

adjustable levelers. Door Lock as per manufactured std, the hinged doors can be locked at once. Door should be provided with Hinge-damping mechanism to enable soft

20.0 closing of doors. Product should be BIFMA gold rated SCSglobal certified for inhouse air quality and with 05 years warranty. Nos. 1 39,000.00 39,000.00

Providing and installation of modular wooden bed of size: 2018W x 2094 D x 925Hmm to be assembled at site. The Bed consists of Decorative Head Board, Foot Board,

Side rail and internal box partitions, Bottom plank and Top planks. The cushioned Headboard is assembly of decorative PVC foiled panels made in 12mm thick MDF, 40mm

thick leatheratte cushioned panel made with backing of 9mm thick prelaminated partcle board and 40mm thick polyurathene fome of 32 dencity, Decorative top profile made

in 25mm thick pvc foiled MDF and side profile made in 40mm thick thin pvc foiled wrapped MDF and fixed on head board. All these decorative profiles and cushion panel is

fixed on headboard base panel made in 15mm thick prelaminated particle board forming head board of 57mm composite thickness. The foot board of 48mm composite

thickness is made in 30mm base panel made with two panels of 15mm thick prelamilated and 15mm thick decorative profiles fixed on upper edge and two vertical edges

made in 15mm thick thin profile wrapped MDF. Body parts like side rail and internal supporting partition are made in 15mm thick mm thick prelaminated particle board with a

21.0 15mm top panel of 35mm thickness pasted on top edge of side rail to strengthened the panel. The Side rail are attached to headboard and footboard with the help of EBCO Nos. 1 67,750.00 67,750.00

made bed clamp of 150mm Length. The Bottom plank is made with 9mm thicj prelaminated particle board with 25mm spacer fixed at bottom to create gap between floor and

plank. The storage box of Bed structure is devided in two parts, the part towards headboard is simple box covered with 15mm thick top plank made with 15mm thick

prelaminated partcle board resting on 25mm plank support fixed on side rail. The second part towards footboard is provided with 3/4 lift-on Donati Mechanism. The Lift-on

mechnism is combination of MS support structure with gas spring fixed on it. All the esposed edges are srealed with 0.8mm thick PVC edge band pasted with the help of hot

melt industrial glue on machines.

Providing and installation of modular bedside table of size: 420W x 400D x 450Hmm, bed side table Carcass & Drawer Facia made up of 18mm thick Melamine finished

Prelaminated Particle Board. Drawer made up of 12mm thick PPB mounted on telescopic slide with 3/4 extension. All edges are sealed with PVC edge-band of 0.45mm

thick. Hardware used from standard range. PVC bushes are fixed at bottom to avoid scratches on dedicated floors. All the material used for this must satisfy quality norms

from IS standards. Boards used must be able to pass 4H test for Scratch resistivity. Decorative paper using for pre-lamination must be imprignated through MF resine.

Decorative Aluminium alloy made Handle to be used for drawer.standard Knock Down fittings to be use for assmbly on site.The bottom panel of drawer is made in 9mm thick

22.0 prelamonated particle baord fixed in the groves made on box panel of the drawer. The Drawer box is assembled with the help of quality fixtures and nylon plugs. Hardware :- Nos. 1 14,500.00 14,500.00

The high quality hardware to be used like telescopic ball bearing slides , Hinges, Minifix, wooden dowel of make Ebco or euivalent.

Providing and supplying corner table of size: 450W x 450D x 400-420Hmm, top made 25mm thk. Pre-Lamibated MDF Board and understructure with a shelf is made of

18mm thick prelaminated MDF board with all exposed edges sealed with 2mm PVC edge banding tape and unexposed edges sealed with 0.6mm PVC edge banding tape

23.0 pressed at 200o C with hot melt glue on special machines. Nos. 2 13,000.00 26,000.00

Digitally signed by AMIT

S. NO. SPECIFICATION UNIT 3rd Floor 2nd Floor UNIT RATE 3rd Floor AMOUNT 2nd floor Amount INDICATIVE IMAGE

TOTAL AMOUNT FOR 2ND AND 3RD FLOOR 11,527,783.44

TOTAL AMOUNT FOR 2ND AND 3RD FLOOR 11,527,783.44

Digitally signed by AMIT