Repair maintenance and installation of new single phase motor.

Supply and fixing of tube well cover of M.S. sheet (6mm thick) with nuts and bolts complete for casing size: 250mm dia

P/Laying ISI marked P.V.C. insulated submersible cable confirming to(IS:694) and as per IS 8130: 2013 of 1.1 kV grade. Wire should be made from 999.90% purity copper, stranding in acc. to IS:8130/ЛЕС 60228 for lower watt loss, oxygen free for less chances of oxidization, insulation PVC type A/C/D, flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, existing pipe / open trench/ Cable tray/ on surface including making connection etc. as required For additional technical parameters of product /work refer Annexure 'A attached with this BSR 2.5 Sq.mm 3 core flat / Round

Rewinding of single phase/3phase submersible motor including all necessary material and of the same characteristics as original with required size of super enamelled wire 'E' class insulation material and testing etc. as required. Replacement of material or components shall be use as per guidelines of OEM of original product. All the scrap material should be retained by the contractor. 2,0 H.P.to 3.0 HP

SITC of Contactor OEM Fabricated DOL/Star-Delta Starter panel with switchgear selection as per Type-2 Cordinatiom Chart and made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON/ OFF push buttons, ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. All as per pre approved by Engineer incharge. For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR. For single phase Submersible / Monoblock pump 2.0 HP to 3.0 HP (DOL starter)

SITC of Radial / mixed flow ISI marked water and anti-corrosive liquid filled submersible motor pump sets suitable for 100/150mm dia borewell. The size of adopter fixed on top of the motor should exceed the top of coupler, for safegaurd the coupler. The construction material of motor and pump should match IS: 8034: 2018 and IS: 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011 with required accessories including making connection suitable for Bore well. The job includes labour part of lowering of riser pipe G.I./ H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to Starter. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect. OEM shall have submit NABL / CPRI/ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in-charge. For additional technical parameters of products/work, refer Annexure "A" attached with this BSR. 100 mm diameter Submersible pump shall have following HP Rating, phase, Head range, Discharge range respectively. 1.5HP, 1-0. (11-94)Mtr, (40-10) LPM

3.0 HP, 1-0, (40-170)Mtr, (60-20) LPM Copper Wound

5.0 HP, 1-0, (56 - 236)Mtr, (90 -25) LPM Copper wound

150 mm diameter Submersible pump shall have following HP Rating, phase, Head range, Discharge range respectively.7.5 HP, 3-0. (76-96)Mtr, (285-180) LPM

Providing & Laying of Polypropylene rope Confirming to IS:5175 for submersible pump of following sizes complete in all respect. All as per pre approved by Engineer in-charge For additional technical parameters of products/ work, refer Annexure "A" attached with this BSR 12mm (suitable up to 50 mm OD pipe)

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) 25 mm nominal bore