SPECIAL REPAIRS TO BLDG NO T-254 (NURSING OFFRS MESS), BLDG NO T-40 (LABORATORY) OF MH AND CERTAIN PROVISION WORKS UNDER AGE B/R-I AT GE (N) AHMEDNAGAR

Amount

Taking down cement plaster on brick or concrete surfaces on wall/ceilling/stone/block etc including racking out joint, hacking for key,scrubbing down with water etc all as specified and as directed.

Demolition of brick work or stone/ boulder masonry/PCC block, built in cement mortar or cement lime mortar including all quoins, pillars etc.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings all as specified and as directed.

M&L for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L for excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / loose soil.

M&L for excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard / dense soil.

M&L for excavation over areas not exceeding 1.5 M deep and getting out in soft / loose Soil

Removing excavated material of soil exc. 250 m but n exc. 500 m and depositing where directed

Returnig, filling in including spreading, levelling, watering and well ramming in layers, n exc 25 cm thick in soil etc complete all as specified and directed by Engineer-in-Charge

Removing exacavated soil to a distance n. exc 50 m and depositing where directed at a level n. exc 1.5 m above the starting point etc complete all as specified and directed by Engineer-in-Charge

M&L for PCC 1:4:8 type D-2 (40mm graded aggregate) in foundation , sub base, filling and mass concrete.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter flat rough finished complete all as specified and directed .

M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide .

M&L for Flat form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exce 200 mm thick.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc

M&L for Formwork to chullah hoods, chajjas, troughs and similar items including edges

M&L for Reinforced Cement Concrete Design Mix Type M-25 (using 20 mm graded granite stone aggregate) in Chajjas

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed .

M&L for Mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed .

M&L for Mild steel TMT bars in stirrups, spacers and binders for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed .

M&L for RCC Design Mix M-25 using 20 mm graded granite stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed .

M&L for RCC Design Mix M-25 using 20 mm graded granite stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed .

M&L for RCC Design Mix M-25 using 20 mm graded granite stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed .

M&L for Hardcore of broken stone of gauge n exc 63mm deposited, spreaded & levelled in layers n exc 15cm thick including watering and ramming etc complete.

Moorum filling in floors/pavings, laid in layers not exceeding 15 cm thick, spread, levelled and rammed/ rolled including watering to required level and gradient.

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6

M&L for Brickwork with fly ash bricks, straight or curved on plan to any radiusin half brick thick walls built in 1:6

M&L for flush pointing to random rubble masonry, uncoursed or brought upto courses CM 1:4

M&L for readymix plaster 10mm thick on fair face of brick work or concrete surfaces finished even and smooth surfaces using without extra cement in internal surfaces.

M&L for readymix plaster 12 mm thick on other than fair face of brick work or concrete surfaces finished even and smooth surfaces using without extra cement of external surface including water proofing compound.

M&L for readymix plaster 5mm thick on fair face of brick work or concrete surfaces finished even and smooth surfaces using without extra cement in ceiling.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 , finished even and smooth without using extra cement and water proofing compound @ 3% by weight of cement (WPC shall be measured and paid separately).

M&L for rendering 10 mm thick in CM 1:6 over brick surfaces, finished even and smooth without using extra cement all as specified and as directed.

M&L for applying two coats of OBD over a coat of primer on newly plastered wall surfaces over 2 mm thick of wall care putty preparation of surfaces all as specified and as directed.

M&L for preparing new plastered surfaces and applying Two coats of cement base paint over a coat of alkali resistant primer on surfaces of walls.

M&L for preparation of newly plastered or unplastered surface and applying three coats of white wash on ceiling.

Supply only integral water proofing compound

M&L for preparing old painted surfaces by washing, rubbing down and stopping of distempered and painted surfaces and applying a coat of distemper oil emulsion on surfaces of walls.

M&L for preparing old painted surfaces by washing, rubbing down and stopping of painted surfaces and applying a coat of cement base paint on surfaces of walls.

M&L for Preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint).

Demolition of Cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) including floor finishes

M&L for 75 mm thick plain cement concrete 1:4:8 type D2, using 40 mm graded stone aggregate as in sub base all as directed.

Demolition floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and removal of debries to a distance not exceeding 100m all as specified and as directed.

Dismantling of stone slabs and tiles of any description or thickness in floors ,aprons etc

S&F light shade Virified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including Screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar 1:6 .

S&F light shade vitrified ceramic tiles 8 to 10mm thick (square/rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in vertical surfaces such as skitings, dado set and jointed in neat cement slurry and pointed in white or coloured cement to match including rendering 10 mm thick in CM 1:4 on fair faces of brick or concrete surfaces of wall as in backing of skirting and dado all as specified and as directed.

M&L for machine cut kota stone flooring 18-20 mm thick over Screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc as directed by Er-In-Charge.

M&L for machine cut kota stone slab 18-20 mm thick in riser of steps,skirting,dado and pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including rendering 10 mm thick in CM 1:4 on fair faces of brick or concrete surfaces of wall as in backing of skirting and dado all as specified and as directed.

M&L for machine cut cudappah stone 18-20 mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for rounding to edges of stone slabs one edge ,such as in steps cooking platform and other similar situations

S&F Non-skid Coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) size of each tiles 400x400 mm in floors etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match including Screed bed or bedding layer of mortar 15mm thick for laying floor finishes in cement mortar 1:6

M&L for Glazed ceramic coloured tiles in vertical surface 350*250*7to 8mm /450x350x7mm to 8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match in backing of skirting and dado including rendering 10 mm thick in CM 1:4 on fair faces of brick or concrete surfaces of wall as in backing of skirting and dado all as specified and as directed.

Taking down of chowkat with shutter without taking off shutters from the frame not exceeding 1.5sqm for architraves, soffits, linings, window boards, etc all as specified and as directed.

Refixing of chowkat with shutter without taking off shutters from the frame not exceeding 1.5sqm for architraves, soffits, linings, window boards, etc all as specified and as directed.

M&L for Aluminium framed windows / Door any pattern, fixed/side hung/silding (three track) using powder coated alluminium sections, of approved make with or with out sash bars suitable for 4mm thick glazing including necessary jointed cleats, handles, glazing all as specified Note-: (glazing shall be measured and paid separatly)

S&F for Anodised aluminium window and ventilator shutters using powder coating (Thickness or powder coating not less than 50 micron), fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F for Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. including powder coating (Thickness or powder coating not less than 50 micron) complete all as specified

S&F for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge.

M&L for 18/19 mm thick Prelaminated particle board, interior grade, prelaminated two side with decorative choice laminations fixed with screws to timber / aluminium frame work

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F sheet glass ordinary quality 3 mm thick exceeding 0.5 sqm in each pane all as specified and as directed.

S&F sheet glass ordinary quality 4.8 mm thick exceeding 0.5 sqm in each pane all as specified and as directed.

M&L for 18-20mm thick granite (of any type ) work (table rubbed and polished ) in steps, jambs, pillars, window -cills, cooking platforms and like in cement (1:4) including pointing in wihte cement (1:2) using marble dust with admixture of pigment ot match with shade of granite including 20mm thick screedbed CM 1:4 complete all as specified and directed .

M&L for mild steel frame work such as grills with ends of bar shouldered, welded or forged into spikes conforming to Fe 410-0 or Fe 310-0 and taking down old one .

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with mild steel Squartube with singal side prelam PVC sheet used instead of plain colour PVC sheed & edges will be painted to match with prelam sheet & fixed in position as per manufacturer's instruction all as specified, as shown on drawing on page No 160 of SSR Part-II 2010

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, with particle board coare supplying & fixing in frame at site as per specification & drawing on sl. page no. 161 of SSR part II 2010

M&L for FE-410W(GdeE-250) quality B Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as spd and as directed.

S&F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel / wooden fillet / steel / aluminium frame all as specified and as directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples all as specified and as directed.

S&F 30mm thick flush door shutter soild core construction with block board core and plywood face panels commercial type on both sides .

S&F butt hinge, stainless steel 100mm long all as specified and as directed.

S&F aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extruded sections or cast aluminium alloy 300 mm long and fixed all as specified and as directed.

S&F Floor door stopper of aluminium alloy body double and tongue anodised with rubber shoe and fixed of size 150 mm all as specified and as directed.

S&F aluminium anodised barrel tower bolt of extruded section 200 mm long and fixed all as specified and as directed.

S&F extruded aluminium alloy handle fabricated type anodised 150 mm long

M&L for preparing new surfaces of wood of any description over 10cm width or girth and apply two coats of synthetic enamel paint over a coat of pink primer all as specified and as directed.

Ditto all as per Sr item No 78 but on steel surfaces over red oxide primer

S&F for 25mm dia curtain rod stainless steel with end fitting not less than 75 gms each and fixed with steel screw in brackets to walls complete all as specified and directed.

S&F in repair aluminium extruded Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed

Dismantling boarding, any description, fixed in wall or ceiling, any position with nails

S&F for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed.

M&L for 4mm thick non asbestos fibre cement building boards of make 'E Board classic designer board (Cascade or Occenic) of M/S Everest industries Ltd or equivalent as approved, fixed or laid/ inserted to timber/GI/Aluminium framework complete all as specified and directed .

Dismantling of wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

Dismantling of frame work in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section

S & F Rolled Mild Steel Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to Fe 410 - W (Gde E-250)quality-A,

S & F in repair vitreous china wash basin, white back, size 550 X 400 mm , errecting on existing CI brackets including taking down old one alll as specified and as directed . Note: If the mentioned size is not available in the market, the next immediate higher size shall be provided by the contractor .

Supply only for 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and taking down old one complete all as specified and as directed

S & F Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) complete in all respect all as specified.in repairs including seat cover with brass screws and excluding flush pipe and flushing cystren

Supply only PVC water closet seat and cover, black or white, closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device including taking down old one all as specified and as directed

S&F in repair brass chromium plated hand shower (Health foucet) with 1 meter long easy flex tube in chrome finish and wall hook with NRV (back flow preventer ) all as directed.

Suppy only in repairs 32 mm dia., Waste fittings, brass chromium plated for glazed ware sinks, wash basins etc., with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.

S&F steel water tubes, `meedium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors of 15 mm bore.

S&F steel water tubes, `meedium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors of 20 mm bore.

S&F stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe 15mm (fancy type chromium plated).

S&F for 15mm dia chromium plated Fancy Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

Taking up or down steel tubing 15mm dia and connections, including cleaning for re- fixing or removal to store

Taking up or down steel tubing 20mm dia and connections, including cleaning for re- fixing or removal to store

Supplying and laying 16 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including connecting to existing GI pipe line complete all as specified

Supplying and laying 20mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including connecting to existing GI pipe line complete all as specified

Supplying and laying 25mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including connecting to existing GI pipe line complete all as specified

Dismantling existing PVC water tanks of capacity exc 250 litres & n.exc 500 litres all as directed and removed from site. NOTE:-Dismantled water tank shall become the contractors property as per Sch of credit.

Dismantling existing PVC water tanks of capacity exc 500 litres & n.exc 1000 litres all as directed and removed from site. NOTE:-Dismantled water tank shall become the contractors property as per Sch of credit.

S&F 500 capacity in litres rotational moulded polyethylene water storage tanks ( cylindrical vertical with closed top ) hoisted & fixed in position all as specified in SSR part I and Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as spd and as directed.

ditto all as per sr item No 105 above but 1000 ltrs.

S&F in repair tubular towel rail, aluminium 20mm dia, D type, 60cm long between flanges

S&F in repairs Fancy type chromium plated with long shank and cup (Concealed type) 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

Supply only in repair 15 mm bore Fancy type pillar taps (Swan neck), Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

S&F in repair 15mm dia Chromium plated fancy type Bib taps cast copper alloy with crutch or butterfly handles screwed down screwed for iron pipe fixed in repair all as spd & directed

Supply only in repair waste coupling of PTMT 32mm (half or full threaded) sutable for kitchen sink. (Minimum weight 32mm- 45gms/40mm-60 gms)

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size mini 815mm x 455mm bowl size 355mm x 355mm x 185mm,including 40mm dia Waste fittings, brass chromium plated for glazed ware sinks, wash basins etc., with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.

S&F in repair grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms)

S&F in repair Chromium plated shower roses 125 mm size with or without swevel joints and size including fixing to steel pipe in 15mm dia.

S&F in repair for Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed

S&F in repair for PVC connections 15mm size with PTMT nuts of length 450mm

S&F in repair for 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls.

S&F in repair for 110 mm bore PVC (SWR) bends of any radius.

S&F in repair for 110 mm bore PVC (SWR) branch piece single (Single `Y') equal or unequal with access door.

S&F in repair for PVC (SWR) pipes single socketed, 75mm dia in any length with rubber ring joints, laid in trenches or in floors

S&F in repair for PVC (SWR) bends any radius 75mm bore

S&F in repair for PVC (SWR) multi floor trap 75mm dia with grating including jointing with solvent cement

S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

M&L for cleaning the newly plastered surfaces of concrete (roof etc) with wire brushes and applying water proofing treatment as under :- (i) Applying one coat of oil bound bituminous primer @ 0.25 kg/Sq. M (ii) Providing and laying 3mm thick APP modified water proofing membrane weighing not less than 3.5 Kg/Sqm reinforced with non woven polyester mat weighing not less than 160 gm/Sqm all as specified procured from any one of the approved manufactures (iii) Apply one coat of solar reflective bituminous aluminium paint @ 0.15 kg/Sqm over membrane over non assesble roof surfaces complete all as per manufactures instructions and as directed.

M&L 75 mm thick cement concrete type C-2, 1:3:6 (Using 40 mm graded aggregate) finishing cement concrete surface even and smooth without using extra cement as in plinth protection including joints and bitumen filling complete all as spd and directed.

M&L for Prestressed precast RCC compound wall of height 1800 mm including excavation of post holes of size 450 x 450 X600 mm for foundation, PCC M 15 Nominal mix in foundation etc. complete all as specified and directed by Engineer in Charge. Column: 150 mm x 150 mm Vertical H section Column with 7 bars of 3 mm HT Steel with M-25 concrete. Precast slabs( incl top design slab) : 2100 x 300 x 50 mm plank with 4 bars of 3 mm HT steel with M-25 concrete. Foundation: 450 x 450 x 600 mm with PCC M 15 Nominal mix

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L for two coats of Cement base paint over a coat of primer etc. complete all as specified and directed by Engineer-in-Charge

S&F in replacement square profile LED lighting fixture with extruded environmental friendly, energy efficient ready to use pack LED Tube light fitiing 10 Watt with LED light source 6500 K,input voltage 140V-270V with uniform light output, with all accessories including its connection with 2 core seathed cable of size 0.5 Sqmm with etc complete all as specified and directed by Engineer-in-Charge.

S&F in replacement square profile LED lighting fixture , environmental friendly, energy efficient ready to use pack Aluminium housing LED Tube light fitiing 22 Watt with LED light source 6500 K,input voltage 160V-270V with uniform light output, with all accessories including its connection with and including 2 core sheathed copper conductor cable of size 0.5 Sqmm with complete with all accessories etc complete all as specified and directed by Engineer-in-Charge .

Taking down carefully copper/aluminum point wiring (light/fan/bell/socket, power point etc) complete, including fixture and fitting such as switches, ceilling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperately) and making good disturbed surfases of walls, floors etc complete all as specified and directed Engineer-in-Charge.

M&L for point wiring complete on surface of wall (open) type with two runs of 1.5 sq mm for phase and neutral single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable drawn in and incl PVC Casing and capping ISI Marked with its accessories PVC boxes (upto 18 module suitble for Mylinc series of Legrand including white plates with frame upto 18 module of make suitable for Mylinc Series ) for fixing switches/socket/regulators etc incl 1.5 sq mm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLSH cable as earth continuity conductor to common earth & connecting to earth dolly for the following, all as specified and directed. Note : 1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2.Wiring shall be done as per complaints recd from user only on required basis it is not necessary to do whole wiring of any whole bldg 3. All points are required to earthed upto fixtures i.e. Holders, Tube lights, Wall lights, ceiling lights, bulkhead lights, bldg security light etc

One light point controlled by switch 5 Amp single pole one way

One Fan point controlled by switch 5 Amp single pole one way

One bell point controlled by switch 5 Amp single pole one way

One 3 pin 5 Amp socket outlet on same board controlled by one, one way 5 Amp switch

One socket outlet 5/3 pin 5 Amp controlled by one switch on independent board

ditto all as per Sr Item No 133 (here-in-before) but with 2.5 Sqmm Copper conductor cable for Phase , Neutral and Earth for one 3 pin, 15 Amp socket outlet on independent board

S&F in replacement bell ding dong elelctric 230V AC single pole etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement Modular Switch, 6 Amp, one way, one Module as per existing. etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement Modular Switch, 16 Amp, one way, one Module as per existing. etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement Modular Socket Outlet 6 Amp, 3 pin, combined two module etc as per existing complete all as specified and directed by Engineer-in-Charge.

S&F in replacement Modular Socket Outlet 6 Amp / 16 Amp - 2/3 pin combined two module as per existing etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement Modular Bell push, 6 Amp, one module etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement Modular Fan Regulator Fan step regulator, 120 Watt - two module etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement lamp holder (Angular/Straight ), insulated body, with back plate for batten fitting etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement ceiling rose 3 terminal / PVC / polycarbonate, isolated body etc complete all as specified and directed by Engineer-in-Charge .

S&F in replacement double door Sheet metal enclosures factory made DBs 4 way TPN, 415 volts ,protection class IP-42, suitable for fixing of MCBs, etc, confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar, With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet complete all as specified and as directed.

S&F in replacement MCB , SP, AC, 240 Volts of 06 to 40 Amp capacity 10KA, 'B' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

S&F in replacement MCBs, TPN, AC, 415 volts of 63 Amps capacity 10 KA, 'B' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge .

S&F in replacement MCBs, SPN, AC, 240 volts of 63 Amps capacity 10 KA, 'C' series and making connections with suitable size of copper lugs etc complete all as specified and directed by Engineer-in-Charge

Supply & fix in replacemnt industrial type switch socket for Geysers with 20 Amp MCB etc complete all as specified and directed by Engineer-in-Charge

S&F sub main wiring with two single core PVC insulated,unsheathed, FRLS stranded copper conductor cable 4 Sqmm with 4 Sqmm PVC insulated, unsheathed, FRLS stranded copper conductor cable as earth wire drawn through and including PVC Casing and capping ISI Marked with its all necessary accessories and earth wire connected to common earth dolly etc complete all as specified and directed by Engineer-in-Charge Note : 1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2. Two run of 4 Sqmm cable i.e for one run for phase, one run for neutral with one run of 4 Sqmm cable for earth and one run of PVC Casing & caping shall be measured as one unit.

S&F sub main wiring with two single core PVC insulated,unsheathed, FRLS stranded copper conductor cable 2.5 Sqmm with 2.5 Sqmm PVC insulated, unsheathed, FRLS stranded copper conductor cable as earth wire drawn through and including PVC casing caping ISI Marked with its all necessary accessories and earth wire connected to common earth dolly etc complete all as specified and directed by Engineer-in-Charge Note : 1. Proper colour coding shall be adopted for wiring (For Phase- Red, Yellow, Blue, For Earth - Green and For Neutral- Black) 2. Two run of 2.5 Sqmm cable i.e for one run for phase, one run for neutral with one run of 2.5 Sqmm cable for earth and one run of PVC casing caping shall be measured as one unit

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. Earth pit not less than 2.25 m depth and top edge of the earth plate not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of nuts, bolts & washer etc. Earth wire connected upto main earth point / DBs alongwith 15mm dia earth protection pipe from top edge of the earth plate to main earth point to be connected and 20mm dia watering pipe light grade with funnel and provn of PCC using cement concrete (1:2:4) mix type B1 using granded stone aggregate and RCC pit cover 50 mm thick precost RCC (1:2:4) mix type B1 duly reinforced with 8 mm dia of TMT bar @ 100 mm CIC, both way, lifting arrangement complete including all necessary earth work etc complete all as specified and directed by Engineer-in-Charge

S & F for plastic body exhaust fan, AC single phase, 240 V of size 200 mm sweep with louvers including necessary connection and replacement of flexible copper cable from ceiling rose and taking down of old unserviceable fan complete all as specified and as directed

M & L for Supply, laying , connecting, testing and commissioning and jointing, LT underground cable in replacement,1100 volts grade, XLPE insulated, armored with galvanized round steel wire or steel strip, electric power cables heavy duty, with multi stranded aluminum conductor, laid in ducts, fixed on poles/walls with proper size saddles and clamp complete all as specified and as directed by the Engineer-in-Charge of following Sizes :- (a) LT cable 25 Sqmm, 3.5 core. Note : Excavation, Earthwork & protection pipe etc shall be measured and paid seprately under relevent items of this Sch.

Supply & laying of HDPE DWC pipe ISI marked of outer dia 50 mm polythylene with smooth internal and profiled external surface for non pressure under ground cable icluding coupler and bends etc complete all as specified and directed by Engineer-in-Charge

Supply & fix in replacement 36 Watt LED Panel 2X2 environmental friendly, new generation,aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source,6500 K suitable for armstrong/Grid ceiling, complete with separate electronic driver ceiling light 36 Watt with and including connecting up with & including twin core, twisted, flexible copper conductor cable of suitable size 230 Volt, 50 HZ etc complete all as specified and directed by Engineer-in-Charge .

S & F in replacement double door Sheet metal enclosures factory made DBs SPN, 8 way ,240 volts ,protection class IP-42,Concealed in wall suitable for fixing of MCBs, Isolators etc, confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar ,With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet complete all as specified and as directed.

S & F in replacement double door Sheet metal enclosures factory made DBs 4 way SPN, 240 volts ,Concealed in wall protection class IP-42, suitable for fixing of MCBs, Isolators etc, confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar ,With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet complete all as specified and as directed.

Supply & fix in replacemnt industrial type switch socket three phasewith 63 Amp TPN MCB etc complete all as specified and directed by Engineer-in-Charge

S&F square profile LED lighting fixture with extruded environmental friendly, energy efficient ready to use pack LED Tube light fitiing 12 Watt with LED light source 6500 K, input voltage 140V-270V with uniform light output, with all accessories including its connection with 2 core seathed cable of size 0.5 Sqmm with etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

Supply and fix air cooled split unit air conditioner electric driven single phase of capacity of 1.5 TR, BEE 5 star duel inverter,HD filter with Anti -virus protection rated ,ADC sensor,copper condensor complete all as specified and as directed.

Supply and fix Voltage stabilizer copper wound for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 140 V to 280 V with output voltage stabilized at 230 V output between 200-240 with low/high cut and time delay relay facility accuracy of ± 2.5% and of capacity 5 KVA

Supply & fix in replacemnt industrial type switch socket with 25 Amp MCB,10 KA etc complete all as specified and directed by Engineer-in-Charge

Arihant Construction (BID ID -3135601)

M/s Meher Construction (BID ID -3135358)

Ms. M.D. Auty (BID ID -3135340)

Priyadeep Construction (BID ID -3135655)

M/s A G Gund (BID ID -3134132)

AZAD SERVICES (BID ID -3134222)

M.H Construction (BID ID -3134688)

M/S CHHTRAPATI CONSTRUCTION (BID ID -3133891)