Carrying out various electric works on Semi Turn Key basis for system strengthening in Municipal area in the area of EE, EUDD II, Mathura under the jurisdiction of SE, EUDC, Mathura

Cartage of following material from Store centre, Mathura to work site.

ST Pole (11 mtr. Long) (Bottom Portion Galvanized)

PCC Pole (8.5 mtr. Long)

ST Pole Pole (13 mtr. Long) (Bottom Portion Galvanized)

11/0.43 KV 400 KVA T/F

11/0.43 KV 250 KVA T/F.

11/0.43 KV 100 KVA T/F.

11/0.43 KV 63 KVA T/F.

LT Aerial Bunch conductor. 3x120 Sq.mm.

LT XLPE cable AL 1X400 sq.mm.

LT PVC cable 1x630 sq.mm.

LT PVC cable 1x400 sq.mm.

AL XLPE cable 1x630 sq.mm.

AL. XLPE 1X400 sqmm. Cable

AL. XLPE 1X240 sqmm. Cable

LT PVC cable 3.5x150sq.mm.

LT PVC cable 3.5x240sq.mm.

LT PVC cable 3.5x70sq.mm.

33 KV XLPE Cable 3x300 Sq.mm.

11 KV XLPE Cable 3x185 Sq.mm.

11 KV XLPE Cable 3x70 Sq.mm.

2Cx10 Sq.mm. armoured cable

4x10 Sq.mm. armoured cable with catenary arrangement

Indoor Cable Jointing Kit I/D 11 KV 3x185 Sq.mm.

Outdoor Cable Jointing Kit O/D 11 KV 3x185 Sq.mm.

Straight Through for 11 KV 3x185 Sq.mm.

Outdoor Cable Jointing Kit O/D 11 KV 3x70 Sq.mm.

Outdoor Cable Jointing Kit O/D 33 KV 3x300 Sq.mm.

ACSR Ins. Weasel conductor

ACSR Weasel conductor

ACSR Dog conductor

D.O. Fuse Set for 11 KV

Cartage of above material like various size 33 KV, 11 kv cable, dog/weasel conductor, Jointing kit, vaccume interrupter, distribution transformers, ST/PCC Pole, VCB, insulator, Disc. fitting, control panel, pin insulator, bus isolator, Line isolator, Bus coupler, brass glands, channel, clamps etc. from Store Center, Mathura to work site and dismentled material from site to dvvnl store.

Digging of pit & erection of new single support ST Pole (13/11 mtr. long) including grouting of pole and fixing of all clamps, cross arm, pin/disc insulator & other accessories with providing stone pad as per relevant drawings. Any fabrication if required for above support.

Digging of pit & erection of new Double Pole Structure ST Pole (13/11 mtr. long) including grouting of pole and fixing of all Sturucture accessories, clamps, cross arm, pin/disc insulator & other accessories with providing stone pad as per relevant drawings. Any fabrication if required for above support.

Earthing of ST/PCC pole/Body earthing of T/F. by M.S earth rod.

Providing & fixing of MS Nut, Bolt and Washer's

Providing & Painting of ST pole with aluminum paint and Red oxide.

Digging of pit & erection of Stay rod with grouting cement sand and brick ballast including Nuzzling, binding Complete. (Stay Insulator providing by contractor)

Filling & Fixing of 11 KV Indoor type cable Jointing Kit for 11 KV 3x185 sqmm.XLPE cable

Filling & Fixing of 11 KV Outdoor type cable Jointing Kit for 11 KV 3x185 sqmm.XLPE cable

Filling & Fixing of 11 KV cable Jointing Kit (Straoght Through) for 11 KV 3x185 sqmm.XLPE cable

Filling & Fixing of 11 KV Outdoor type cable Jointing Kit for 11 KV 3x70 sqmm.XLPE cable

Filling & Fixing of 33 KV Indoor type cable Jointing Kit for 33 KV 3x300 sqmm.XLPE cable

Sagging of Weasel/Dog conductor on erected poles.

Sagging/Jumpering of Ins. Weasel/Dog conductor

Digging of trench by Making pits/open trench method/HDD method after due survey with the help of utility detector of existing electrical/telephonic cable/and other utilites of public utilites department and laying , Testing, Commisiong & energization of cables of 33 KV/11 kv XLPE double ckt. Cable by manual drill (by making moles) /HDD method/ open trench Including all material Like brick & sand and Back filling and restoring the road to make as original.

Sagging & Laying of 33/11 KV XLPE cable in Double Pole structure/Loop etc.

Laying of Laying of 2c/10 sq.mm. armoured Cable

Laying of 4X10 XLPE armoured Cable With Catenary arrange ment

Digging of trench by Making pits/open trench method/HDD method after due survey with the help of utility detector of existing electrical/telephonic cable/and other utilites of public utilites department and laying , Testing, Commisiong & energization of cables of LT XLPE/PVC/Al. double ckt. Cable by manual drill (by making moles) /HDD method/ open trench Including all material Like brick & sand and Back filling and restoring the road to make as original.

Sagging & Laying of LT cable 3.5x150/240sq.mm.

Laying of LT ABC 3X120 sq.mm. Cable

Laying LT XLPE cable AL 1X400 sq.mm.

Laying LT PVC cable 1x630 sq.mm.

Laying LT PVC cable 1x400 sq.mm.

Laying AL XLPE cable 1x630 sq.mm.

Laying AL. XLPE 1X400 sqmm. Cable

Laying AL. XLPE 1X240 sqmm. Cable

Guarding of 33KV/11 KV line. (including G.I. Wire and other related items)

Providing and Fixing of 11 KV Holding Clamp For ST Pole

Providing & fixing of G.I. Pipe 4"/6" dia

Providing & fixing of Clamp For G.I. Pipe

Providing & fixing of Guarding Angle for 33/11 KV

Providing & fixing of I Bolt for Guarding

Providing & fixing of Aluminium Biding Wire for Guarding

Providing & fixing of clamp for guarding angle for 11 KV line

Providing & Fixing of Cable end termination using total double compression brass glands for 3.5x70 sq.mm. XLPE Cable

Providing & Fixing of Cable end termination using total double compression brass glands for 3.5x150 sq.mm. XLPE Cable

Providing & Fixing of Cable end termination using total double compression brass glands for 3.5x240 sq.mm. XLPE Cable

C Panel Disconeccting and dismentling of existing C panel and Supply, installation testing commisioning of factory fabricated & wired metal clad dust and vermin proof double door type outdoor application stand mounting, M.S. Channel Base incliding channel stand with bottom cable entreis The panel board shall have suitable capacity electrolytic alumininum busbars as per IS8623 or above istulated with heat shrink sleeving and mounted on nonhygroscopic supports such as CMC/BMC support. panel shall be complete with suitable cable end boxes, double compression glands. panel comparment having special provision for internal locking system for stop the electricity theft The panel board shall be fabricated with gelvnized prime sheet with a minimum thickness of 1.6mm/2mm. with seven tank process powder coated. panel haveing proper space for connecting incomming and outgoing cable terminations MAKE: APC/SCHEINDER/ABB/SIEMENS/C&S & Complete with insulation of bakelite strip (08 mm/10 mm) thickness.

Earthing Complete for C Type Panels by earth rod

Providing & fixing of Lt ACB 800 Amp Nos. 250 Amp. Output MCCB and suitable covering & mounting strucuture

Providing & fixing of Lt ACB 630 Amp Nos. 250 Amp. Output MCCB and suitable covering & mounting strucuture

Providing & fixing of Foundation of RMU 3 Cubic Meter

Pipe and Pipe gel Earthing for R.M.U

Providing & fixing of Danger Board

Providing & fixing of Barbed Wire

Sagging of Guarding G.I. Wire

Providing & fixing of Stone Pad

Providing & fixing of Boot Protection For T/F Monkey Fault

Providing & fixing 16 sqmm. Alumimum thimble

Providing & Fixing of PVC Pipe 3" of diameter

Providing and Instllation of 24 Volt Battery with Charger.

Providing & Fixing of 33 KV V type Steel Cross Arm

Provoding & Fixing of 11 KV V type Steel Cross Arm

Providing & Fixing of 11 KV Pin Insulator with pin

Providing & Fixing of 33 KV V type Steel Cross Arm Holding Clamp

Providing & Fixing of 11 KV V type Steel Cross Arm Holding Clamp

Providing & Fixing of 33 KV Pin Insulator with pin

Providing & Fixing of Disc Insulator 45 KN & 70 KN (T&C/B&S) with fitting

Providing & fixing of 33 KV F Bracket

Providing & fixing of 11 KV F Bracket

Providing & fixing of Packing Piece Clamp for 33 KV/11 KV with nut & bolts

Providing & fixing of Aluminium Lug 25 sqmm.

Providing & fixing of Aluminium Lug 70 sqmm.

Providing & fixing of Aluminium Lug 150 sqmm.

Providing & fixing of Aluminium Lug 240 sqmm.

Providing & fixing of Aluminium Lug 400 sqmm.

Providing & fixing of Aluminium Lug 630 sqmm.

Providing & fixing of Aluminium Lug 1000 sqmm.

Providing & Sagging/Fixing of Al. XLPE 1x1000 Sq.mm. Cable

Installation of 11/0.4 KV, 400 KVA T/F Mobile Trolley

Providng Trolley Structure for 400 KVA T/F with vehicle tyre,rim,coupling,trolly hook,earthing, painting and related accessories with complete job

Supply of G.I. Pipe Chemical earthing electrode 3 mtr. long 80 mm inner dia along with chemical powder and 50x6 mm G.I. Strip with Nut, Bolt and Washer.

Earthing of Power Transformer (Urban) by digging of pit up to water level depth Approx. 90 feet. into the boring 1-1/4" dia GI pipe of "B" grade,conforming to the requirement of IS specification and then connecting the top of the inserted pipe and Power Transformer body earthing through M.S. strip of size 50x6mm with the help of Electric welding Lum Sum Rate. It includes the cost of all material, labour, Carrier etc. required for proper completion of work.

Installation of D.O. Fuse Set of 11 KV

Supply, install, testing and commisioning of 11 KV 630 Amps 21 KA for 3 Sec. SF6 insulated, one side extesible, outdoor duty 3 way R.M.U. manual operate, in combination of 01 nos. VCB modules (O/G) & 2 Nos. Load Breaker Switch modules (I/C), CONSITIING OF COPPER BUSBAR in SF6 insulated 304 (Non-Ferrite Non-Magnetic Grade) stainless steel enclosure of thickness 2.5 mm with manometer fixed on the tank. the breaker shall have mechanical ON/OFF indicator with hand Trip device and spring charging, spring relase coil, auxiliary switch of 02 NO +2NC. The HV switchgerar and control gear should be confirming to IEC-62271-100, IEC-62271-200-2003 & IEC-60694-1996. The RMU gas tank should be internal arc tested for 21 KA for 1Second with IAC-AFL classification for gas tank. The complete RMU Should have ingress protection of minimum IP54. The RMU design should support site replaceable HT cable bushing. All the type test certified as per IEC from Third party lab to be submitted. RMU should have :- 01 Nos. micorprocessor based self powered numerical relay with over Current/earth fault & short circuit protection wiht each VCB feeder. - 3Nos. Protection CT Shall be of Burden 2.5 VA, ratio 200/1A, Class of Accuracy class 5P10 for O/C and E/F Protection for each VCB. (CT ration is indicative and may vary during detailed engineering) -1 No. Manometer for each tank-1 Nos. Voltage passage indicator for each feeder. -1 Nos. Fault Passage Indicator for each LBS Module.- Right angle boots for all the feeder Modules- Basic insulation level of complete system shall be 28KV(RMS)/75KV(Peak)- Vacuum Interrupter & RMU Should be of same make for better life cycle optimization.

Supply, install, testing and commisioning of 11 KV 630 Amps 21 KA for 3 Sec. SF6 insulated, one side extesible, outdoor duty 4 way R.M.U. manual operate, in combination of 02 nos. VCB modules (O/G) & 2 Nos. Load Breaker Switch modules (I/C), CONSITIING OF COPPER BUSBAR in SF6 insulated 304 (Non-Ferrite Non-Magnetic Grade) stainless steel enclosure of thickness 2.5 mm with manometer fixed on the tank. the breaker shall have mechanical ON/OFF indicator with hand Trip device and spring charging, spring relase coil, auxiliary switch of 02 NO +2NC. The HV switchgerar and control gear should be confirming to IEC-62271-100, IEC-62271-200-2003 & IEC-60694-1996. The RMU gas tank should be internal arc tested for 21 KA for 1Second with IAC-AFL classification for gas tank. The complete RMU Should have ingress protection of minimum IP54. The RMU design should support site replaceable HT cable bushing. All the type test certified as per IEC from Third party lab to be submitted. RMU should have :- 01 Nos. micorprocessor based self powered numerical relay with over Current/earth fault & short circuit protection wiht each VCB feeder. - 3Nos. Protection CT Shall be of Burden 2.5 VA, ratio 500/1A, Class of Accuracy class 5P10 for O/C and E/F Protection for each VCB. (CT ration is indicative and may vary during detailed engineering) -1 No. Manometer for each tank-1 Nos. Voltage passage indicator for each feeder. -1 Nos. Fault Passage Indicator for each LBS Module.- Right angle boots for all the feeder Modules- Basic insulation level of complete system shall be 28KV(RMS)/75KV(Peak)- Vacuum Interrupter & RMU Should be of same make for better life cycle optimization.

Supply, install, testing and commisioning of 11 KV 630 Amps 21 KA for 3 Sec. SF6 insulated, one side extesible, outdoor duty 5 way R.M.U. manual operate, in combination of 03 nos. VCB modules (O/G) & 2 Nos. Load Breaker Switch modules (I/C), CONSITIING OF COPPER BUSBAR in SF6 insulated 304 (Non-Ferrite Non-Magnetic Grade) stainless steel enclosure of thickness 2.5 mm with manometer fixed on the tank. the breaker shall have mechanical ON/OFF indicator with hand Trip device and spring charging, spring relase coil, auxiliary switch of 02 NO +2NC. The HV switchgerar and control gear should be confirming to IEC-62271-100, IEC-62271-200-2003 & IEC-60694-1996. The RMU gas tank should be internal arc tested for 21 KA for 1Second with IAC-AFL classification for gas tank. The complete RMU Should have ingress protection of minimum IP54. The RMU design should support site replaceable HT cable bushing. All the type test certified as per IEC from Third party lab to be submitted. RMU should have :- 01 Nos. micorprocessor based self powered numerical relay with over Current/earth fault & short circuit protection wiht each VCB feeder. - 3Nos. Protection CT Shall be of Burden 2.5 VA, ratio 500/1A, Class of Accuracy class 5P10 for O/C and E/F Protection for each VCB. (CT ration is indicative and may vary during detailed engineering) -1 No. Manometer for each tank-1 Nos. Voltage passage indicator for each feeder. -1 Nos. Fault Passage Indicator for each LBS Module.- Right angle boots for all the feeder Modules- Basic insulation level of complete system shall be 28KV(RMS)/75KV(Peak)- Vacuum Interrupter & RMU Should be of same make for better life cycle optimization.

Providing & Fixing of Dead end clamp With I-Hook

Providing & Fixing of Suspension Clamp With I- Hook

Providing & Fixing of piercing Clamp

Installation of LT Distribution Box

Providing & Fixing of PVC Pipe 2" of diameter

Providing & Fixing of Clamp For Distribution Box

Concreting of Pole (ST 13 Mtr./11 Mtr.) PCC Pole

Providing and Fixing/Installation of Compact Substation T/F of 400 KVA including all relevant and required accessories.

Removal of old transformer(250 KVA) with all connected accessories from existing double pole.

Removal of old transformer(100 KVA) with all connected accessories from existing double pole.

Removal of old transformer(63KVA) with all connected accessories from existing double pole.

Removal of old transformer(25KVA) with all connected accessories from existing double pole.

Construction of Plinth 6x6x4 Height from ground as per sc (as per approved GTP)

Installation of following transformer on Plinth/Double pole with all connecting accessories jumering etc. including carriage of transformers from store centre, Mathura to work site.

400 KVA Transformer on Plinth

250 KVA Transformer on Plinth

100 KVA Transformer on Double Pole

63 KVA Transformer on Double Pole

Providing and Installation of Tail less unit complete

Mash/FRP Fencing of Sub-Station with civil works (as per approved GTP)

Complete Pipe in Pipe Gel earthing of 11/0.4 KV 250/400 Distribution Transformer by digging pits 6” dia upto 3 mtr. deep including chemical filled pipe in between (pipe-in-pipe) ISI mark B Grade & connecting with G.I strip of size 50mm X 6mm with neutral/body of 11/0.4 KV distribution transformer to above pipe-in-pipe (PIP) and filling of chemical crystalline conductive mixture containing highly conductive material around the (pipe-in-pipe) up to 3 Mtr. including making of chamber at the top of the earthing. Other details are as below:- 1.Earth pipe material – mild steel, Galvanised. 2-Main Electrode diameter – 42.4mm. 3-Auxiliary Electrode pipe, Diameter – 76mm. 4-Wall Thickness of main Electrode :- 2.6mm. 5-Wall thickness of auxiliary Ist whole:- 3.2mm. 6- Length of earthing electrode (PIP):- 3 Meter.

Dismantling of damaged & used items i.e. Distribution Transformer, ST/PCC Pole, HT/LT cable, Conductor (Scrap) & other accessories at work site and carriage dismantled material from Site to Store Center, Mathura.

Proper Road Restoration Kaccha/Pakka (If required) Rates shall be acceptable, if not given above for the same work.

Bee Pee Electricals